The IMX_GPIO_NR() macro was only used by non-DT i.MX platforms.
As i.MX transitioned to a DT-only platform, get rid of this
unused macro.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The I2C buses are not declared at the device tree. As this will
be needed by further patches, add them, keeping all in
disabled state. Per-board settings can override it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
There are several pinctrl settings that are missing at this
DT file.
Also, the entries are out of order.
Add the missing bits, as they'll be required by the DRM driver - and
probably by other drivers not upstreamed yet.
Reorder the entres, adding the missing bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This is required in order to support USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The "smmu-cb-memtype" is a private property developed by the Hisilicon
driver in the early stage and is not used now. So delete it.
Otherwise, below YAML check warnings are reported:
arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Currently, the names of several nodes incorrectly match common PHY
provider schema. And the phy-provider.yaml requires them must have
property "#phy-cells". As a result, false positives similar to the
following are reported:
usb2-phy@120: '#phy-cells' is a required property
Change their names slightly so that they do not match pattern:
"^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Change the node name of the localbus to match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'. This error
is detected by simple-bus.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
1. Change the node name of the thermal zone to match
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal".
2. Change the node name of the trip point to match
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Look at the clock-names schema defined in arm,mali-utgard.yaml:
clock-names:
items:
- const: bus
- const: core
The "bus" needs to be placed before the "core".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Do not write the "ranges" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported:
soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not valid under \
any of the given schemas (Possible causes of the failure):
soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not of type 'boolean'
soc: pcie@a0090000:ranges:0: [33554432, 0, 2986344448, 0, 2986344448, 0, \
100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch unifies the error messages:
- have a "." and the end of each message
- write controller with a small "c", if not the first word of an error
message.
Link: https://lore.kernel.org/r/20210128104644.2982125-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The published errata specify the maximum allowed SPI frequency to be
max 85% of (FSYSCLK/2). So there's no need to track known bad clock
settings in the driver. As the setup of known good values is a bit
tricky, keep them.
Link: https://lore.kernel.org/r/20210128104644.2982125-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the reference to the errata for both the mcp2517fd
and the mcp2518fd.
Fixes: f5b84dedf7 ("can: mcp25xxfd: mcp25xxfd_probe(): add SPI clk limit related errata information")
Link: https://lore.kernel.org/r/20210128104644.2982125-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The VT-d IOMMU response RESPONSE_FAILURE for a page request in below
cases:
- When it gets a Page_Request with no PASID;
- When it gets a Page_Request with PASID that is not in use for this
device.
This is allowed by the spec, but IOMMU driver doesn't support such cases
today. When the device receives RESPONSE_FAILURE, it sends the device
state machine to HALT state. Now if we try to unload the driver, it hangs
since the device doesn't send any outbound transactions to host when the
driver is trying to clear things up. The only possible responses would be
for invalidation requests.
Let's use RESPONSE_INVALID instead for now, so that the device state
machine doesn't enter HALT state.
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210126080730.2232859-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
It is incorrect to always clear PRO when it's set w/o first checking
whether the overflow condition has been cleared. Current code assumes
that if an overflow condition occurs it must have been cleared by earlier
loop. However since the code runs in a threaded context, the overflow
condition could occur even after setting the head to the tail under some
extreme condition. To be sane, we should read both head/tail again when
seeing a pending PRO and only clear PRO after all pending PRs have been
handled.
Suggested-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/linux-iommu/MWHPR11MB18862D2EA5BD432BF22D99A48CA09@MWHPR11MB1886.namprd11.prod.outlook.com/
Link: https://lore.kernel.org/r/20210126080730.2232859-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since 5d283b0838 ("clk: imx6: Fix procedure to switch the parent
of LDB_DI_CLK"), the clock driver warns if ldb_di\d_sel is changed
from reset value on system boot. This warning is printed even if
the bootloader (or a previous kernel that did kexec) followed the
correct procedure for glitch-free reparenting.
As such systems are doing everything correctly, a warning is too
harsh. Demote to a notice, so users are still alerted, but without
cluttering a loglevel=5 boot.
While at it, add the words "possible glitch" into the log message, to
make it more user-friendly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add librem5-r4 with specifics to that revision like the near-level,
battery and charger properties. For schematics and more information,
see https://developer.puri.sm/Librem5/Hardware_Reference/Evergreen.html
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Expect all those regulators to be turned on initially.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables the Librem5's ft8006p based LCD panel driven by the
imx8mq's Northwest Logic DSI IP core and mxsfb display controller.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It's a supply for to touch and LCD.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The tps65982 feeds the bq25895 charge controller on the Librem 5.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the pmic driver fixed we can now shut off the regulator in the gpc.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is consistent with other IRQs and makes keeps currents low.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
vdda1v1 and vdda1v8 supplies are required by USB PLL. Add them in usbphyc
node.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add SDA/SCL pinmux lines for I2C6 on STM32MP1.
This support adds both in default and sleep states.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The haptic motor for the Librem 5 uses this.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for the Librem 5 phone, Evergreen revision which is supported
by "r4". Schematics and more information can be found at
https://developer.puri.sm/Librem5/Hardware_Reference/Evergreen.html
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"make dtbs_check" fails with:
arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dt.yaml: eeprom@50: compatible: 'oneOf' conditional failed, one must be fixed:
'microchip,at24c64' does not match '^(atmel|catalyst|microchip|nxp|ramtron|renesas|rohm|st),(24(c|cs|lc|mac)[0-9]+|spd)$'
Fix this by dropping the bogus "at" prefix.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210128110136.2293490-1-geert+renesas@glider.be
The R-Car System Controller (SYSC) driver registers PM domains from an
early_initcall(). It does not use a platform driver, as secondary CPU
startup on R-Car H1 needs to control the CPU power domains, before
initialization of the driver framework.
As fw_devlink only considers devices, it does not know that the System
Controller is ready. Hence probing of on-chip devices that are part of
the SYSC PM domain fails if fw_devlink is enabled:
probe deferral - supplier e6180000.system-controller not ready
Fix this by setting the OF_POPULATED flag for the SYSC device node after
successful initialization. This will make of_link_to_phandle() ignore
the SYSC device node as a dependency, and consumer devices will be
probed again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210128082847.2205950-1-geert+renesas@glider.be
- Fix DP vswing settings and handling (Imre, Ville)
- Various display code clean-up (Jani, Ville)
- Various display refactoring, including split out of pps, aux, and fdi (Ja\
ni, Dave)
- Add DG1 missing workarounds (Jose)
- Fix display color conversion (Chris, Ville)
- Try to guess PCH type even without ISA bridge (Zhenyu)
- More backlight refactor (Lyude)
- Support two CSC module on gen11 and later (Lee)
- Async flips for all ilk+ platforms (Ville)
- Clear color support for TGL (RK)
- Add a helper to read data from a GEM object page (Imre)
- VRR/Adaptive Sync Enabling on DP/eDP for TGL+ (Manasi, Ville Aditya)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmARc1oACgkQ+mJfZA7r
E8ovFAgAhBlnhrquGrgtuRmS5tkpLQShqiwrPv7ogDBkcayJ6Is+AO+FoE8kuzZO
q/TW2enkcRKFHhQnm9RA0Ayk+rwYqkEOcBU5gvzusdwbEjkygJfH/yA2ukAmaw32
QxP9A2pW+iWsEcqtMuOEu1ahu0Z8gnkCe8DakuBMf/0y5D9DairwaCC8nyZQdEJq
YFTxp+pILE57PhOVbKS3EZPbnl5t28NgCtMc8hjlPTWZxRSVV0eDrY2tx9vyhFhU
Eq8aLDxPKCRm18sg+J+lDytOvFoljXcglAEwPODVMmDNolG8R6aRQ9T6tG6qfxyI
UO1KyeYUHHEIJ4IBJKK+KWeUWLLBhA==
=3Jc8
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2021-01-27' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- HDCP 2.2 and HDCP 1.4 Gen12 DP MST support (Anshuman)
- Fix DP vswing settings and handling (Imre, Ville)
- Various display code clean-up (Jani, Ville)
- Various display refactoring, including split out of pps, aux, and fdi (Ja\
ni, Dave)
- Add DG1 missing workarounds (Jose)
- Fix display color conversion (Chris, Ville)
- Try to guess PCH type even without ISA bridge (Zhenyu)
- More backlight refactor (Lyude)
- Support two CSC module on gen11 and later (Lee)
- Async flips for all ilk+ platforms (Ville)
- Clear color support for TGL (RK)
- Add a helper to read data from a GEM object page (Imre)
- VRR/Adaptive Sync Enabling on DP/eDP for TGL+ (Manasi, Ville Aditya)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210127140822.GA711686@intel.com
Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit
links from sporadically dropping. Jon Nettleton found that a value
of 23 was the minimum to give a stable link, but testing with the
Com Express 7 module shows 24 is the minimum - so 23 may still be on
the margins. Use 24 instead for consistency across SolidRun platforms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no point calling dev_pm_opp_set_clkname() with the "name"
parameter set to NULL, this is already done by the OPP core at setup
time and should work as it is.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/0f22cc1791d8b88c50a9790c2dc19455b34ec7b0.1611742564.git.viresh.kumar@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit
links from sporadically dropping. Testing on this platform shows that
a value of 24 results in a stable link, whereas 23 or below has the
occasional drop.
Tested with a Netgear GS116 unmanaged switch link partner with Cat 5e
cabling.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In some cases we have the handle those explicitly as the fallback
connector type detection fails and marks those as eDP connectors.
Attempting to use such a connector with mutter leads to a crash of mutter
as it ends up with two eDP displays.
Information is taken from the official DCB documentation.
Cc: stable@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Noticed that I wasn't paying close enough attention the last time I looked
at our audio callbacks, as I completely missed the fact that we were
figuring out which audio-enabled connector goes to each encoder by checking
it's state, but without grabbing any of the appropriate modesetting locks
to do so.
That being said however: trying to grab modesetting locks in our audio
callbacks would be very painful due to the potential for locking inversion
between HDA and DRM. So, let's instead just copy what i915 does again - add
our own audio lock to protect audio related state, and store each audio
enabled connector in each nouveau_encoder struct so that we don't need to
check any atomic states.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drm_encoder->crtc is deprecated for atomic drivers, but
nouveau_encoder->crtc is safe.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Despite being an atomic driver, nouveau has a lot of leftover code that
relies on retrieving information regarding the new atomic state from
members of drm_encoder and drm_crtc. The first field being used,
drm_encoder.crtc, is deprecated for atomic drivers. The second field being
used is drm_crtc.state, which is only really sensible to use outside of an
atomic modeset.
So, add some helpers to lookup the current crtc for a given outp from the
atomic state. Then, convert most of the code in dispnv50/disp.c to use said
new helper, along with the relevant DRM atomic helpers for retrieving the
new encoder/crtc combinations for a new atomic state.
Note that we don't get rid of the nouveau_encoder.crtc field entirely for
three reasons:
- Legacy modesetting for pre-nv50 still uses it
- It doesn't cause any locking issues
- We need it for the HDA callbacks, as grabbing atomic modesetting locks in
those would be a mess.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Just to be more consistent with the order of args that DRM helpers like
drm_atomic_get_new_crtc_state() use.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I have a strange dejavu feeling that I tried to submit a patch for this in
the past, but that it was rejected. I can't remember though, but I'm
further convinced this patch is the right thing to do anyway.
We label the to-be-committed head state in nv50_msto_atomic_enable() as
armh. Normally armh implies a state which is currently armed in hardware.
nv50_msto_atomic_enable() is called _after_ drm_atomic_swap_state()
however, but before the commit tail ends, which means that said state is
not actually armed on hardware.
As well - take note that this is the same convention followed in all of the
other atomic_enable() callbacks.
So, let's correct this to asyh.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>