commit 0cf9e48ff2 upstream.
Leverage gpiochip_line_is_irq to check whether a pin has an irq
associated with it. The previous check ("irq == 0") didn't make much
sense. The irq variable refers to the pinctrl irq, and has nothing do to
with an individual pin.
On some systems, during suspend/resume cycle, the firmware leaves
an interrupt enabled on a pin that is not used by the kernel.
Without this patch that caused an interrupt storm.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Kornel Dulęba <korneld@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-4-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a855724dc0 upstream.
commit 4e5a04be88 ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100. Offset 0xFC is actually `WAKE_INT_MASTER_REG`. This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-3-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968ab92616 upstream.
commit 4e5a04be88 ("pinctrl: amd: disable and mask interrupts on probe")
had a mistake in loop iteration 63 that it would clear offset 0xFC instead
of 0x100. Offset 0xFC is actually `WAKE_INT_MASTER_REG`. This was
clearing bits 13 and 15 from the register which significantly changed the
expected handling for some platforms for GPIO0.
commit b26cd9325b ("pinctrl: amd: Disable and mask interrupts on resume")
actually fixed this bug, but lead to regressions on Lenovo Z13 and some
other systems. This is because there was no handling in the driver for bit
15 debounce behavior.
Quoting a public BKDG:
```
EnWinBlueBtn. Read-write. Reset: 0. 0=GPIO0 detect debounced power button;
Power button override is 4 seconds. 1=GPIO0 detect debounced power button
in S3/S5/S0i3, and detect "pressed less than 2 seconds" and "pressed 2~10
seconds" in S0; Power button override is 10 seconds
```
Cross referencing the same master register in Windows it's obvious that
Windows doesn't use debounce values in this configuration. So align the
Linux driver to do this as well. This fixes wake on lid when
WAKE_INT_MASTER_REG is properly programmed.
Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217315
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230421120625.3366-2-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ae071fc21 upstream.
Josh Triplett reports that initramfs-tools needs modules.builtin and
modules.builtin.modinfo to create a working initramfs for a non-modular
kernel.
If this is a general tooling issue not limited to Debian, I think it
makes sense to change modules_install.
This commit changes the targets as follows when CONFIG_MODULES=n.
In-tree builds:
make modules -> no-op
make modules_install -> install modules.builtin(.modinfo)
External module builds:
make modules -> show error message like before
make modules_install -> show error message like before
Link: https://lore.kernel.org/lkml/36a4014c73a52af27d930d3ca31d362b60f4461c.1686356364.git.josh@joshtriplett.org/
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Tested-by: Nicolas Schier <nicolas@fjasle.eu>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Tested-by: Josh Triplett <josh@joshtriplett.org>
Stable-dep-of: 4243afdb93 ("kbuild: builddeb: always make modules_install, to install modules.builtin*")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 458c15dfbc upstream.
syzbot reports a bug as below:
general protection fault, probably for non-canonical address 0xdffffc0000000009: 0000 [#1] PREEMPT SMP KASAN
RIP: 0010:__lock_acquire+0x69/0x2000 kernel/locking/lockdep.c:4942
Call Trace:
lock_acquire+0x1e3/0x520 kernel/locking/lockdep.c:5691
__raw_write_lock include/linux/rwlock_api_smp.h:209 [inline]
_raw_write_lock+0x2e/0x40 kernel/locking/spinlock.c:300
__drop_extent_tree+0x3ac/0x660 fs/f2fs/extent_cache.c:1100
f2fs_drop_extent_tree+0x17/0x30 fs/f2fs/extent_cache.c:1116
f2fs_insert_range+0x2d5/0x3c0 fs/f2fs/file.c:1664
f2fs_fallocate+0x4e4/0x6d0 fs/f2fs/file.c:1838
vfs_fallocate+0x54b/0x6b0 fs/open.c:324
ksys_fallocate fs/open.c:347 [inline]
__do_sys_fallocate fs/open.c:355 [inline]
__se_sys_fallocate fs/open.c:353 [inline]
__x64_sys_fallocate+0xbd/0x100 fs/open.c:353
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The root cause is race condition as below:
- since it tries to remount rw filesystem, so that do_remount won't
call sb_prepare_remount_readonly to block fallocate, there may be race
condition in between remount and fallocate.
- in f2fs_remount(), default_options() will reset mount option to default
one, and then update it based on result of parse_options(), so there is
a hole which race condition can happen.
Thread A Thread B
- f2fs_fill_super
- parse_options
- clear_opt(READ_EXTENT_CACHE)
- f2fs_remount
- default_options
- set_opt(READ_EXTENT_CACHE)
- f2fs_fallocate
- f2fs_insert_range
- f2fs_drop_extent_tree
- __drop_extent_tree
- __may_extent_tree
- test_opt(READ_EXTENT_CACHE) return true
- write_lock(&et->lock) access NULL pointer
- parse_options
- clear_opt(READ_EXTENT_CACHE)
Cc: <stable@vger.kernel.org>
Reported-by: syzbot+d015b6c2fbb5c383bf08@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-f2fs-devel/20230522124203.3838360-1-chao@kernel.org
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27655b9bb9 upstream.
Generate a hotplug event after registering a client to allow the
client to configure its display. Remove the hotplug calls from the
existing clients for fbdev emulation. This change fixes a concurrency
bug between registering a client and receiving events from the DRM
core. The bug is present in the fbdev emulation of all drivers.
The fbdev emulation currently generates a hotplug event before
registering the client to the device. For each new output, the DRM
core sends an additional hotplug event to each registered client.
If the DRM core detects first output between sending the artificial
hotplug and registering the device, the output's hotplug event gets
lost. If this is the first output, the fbdev console display remains
dark. This has been observed with amdgpu and fbdev-generic.
Fix this by adding hotplug generation directly to the client's
register helper drm_client_register(). Registering the client and
receiving events are serialized by struct drm_device.clientlist_mutex.
So an output is either configured by the initial hotplug event, or
the client has already been registered.
The bug was originally added in commit 6e3f17ee73 ("drm/fb-helper:
generic: Call drm_client_add() after setup is done"), in which adding
a client and receiving a hotplug event switched order. It was hidden,
as most hardware and drivers have at least on static output configured.
Other drivers didn't use the internal DRM client or still had struct
drm_mode_config_funcs.output_poll_changed set. That callback handled
hotplug events as well. After not setting the callback in amdgpu in
commit 0e3172bac3 ("drm/amdgpu: Don't set struct
drm_driver.output_poll_changed"), amdgpu did not show a framebuffer
console if output events got lost. The bug got copy-pasted from
fbdev-generic into the other fbdev emulation.
Reported-by: Moritz Duge <MoritzDuge@kolahilft.de>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2649
Fixes: 6e3f17ee73 ("drm/fb-helper: generic: Call drm_client_add() after setup is done")
Fixes: 8ab59da26b ("drm/fb-helper: Move generic fbdev emulation into separate source file")
Fixes: b79fe9abd5 ("drm/fbdev-dma: Implement fbdev emulation for GEM DMA helpers")
Fixes: 63c381552f ("drm/armada: Implement fbdev emulation as in-kernel client")
Fixes: 49953b70e7 ("drm/exynos: Implement fbdev emulation as in-kernel client")
Fixes: 8f1aaccb04 ("drm/gma500: Implement client-based fbdev emulation")
Fixes: 940b869c2f ("drm/msm: Implement fbdev emulation as in-kernel client")
Fixes: 9e69bcd88e ("drm/omapdrm: Implement fbdev emulation as in-kernel client")
Fixes: e317a69fe8 ("drm/radeon: Implement client-based fbdev emulation")
Fixes: 71ec16f45e ("drm/tegra: Implement fbdev emulation as in-kernel client")
Fixes: 0e3172bac3 ("drm/amdgpu: Don't set struct drm_driver.output_poll_changed")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Moritz Duge <MoritzDuge@kolahilft.de>
Tested-by: Torsten Krah <krah.tm@gmail.com>
Tested-by: Paul Schyska <pschyska@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mikko Perttunen <mperttunen@nvidia.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: amd-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # msm
Link: https://patchwork.freedesktop.org/patch/msgid/20230710091029.27503-1-tzimmermann@suse.de
[ Dropped changes to drivers/gpu/drm/armada/armada_fbdev.c as
174c3c38e3 drm/armada: Initialize fbdev DRM client
was introduced in 6.5-rc1 ]
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49024ec879 upstream.
Handle trailing and leading separators when parsing UNC and prefix
paths in smb3_parse_devname(). Then, store the sanitised paths in
smb3_fs_context::source.
This fixes the following cases
$ mount //srv/share// /mnt/1 -o ...
$ cat /mnt/1/d0/f0
cat: /mnt/1/d0/f0: Invalid argument
The -EINVAL was returned because the client sent SMB2_CREATE "\\d0\f0"
rather than SMB2_CREATE "\d0\f0".
$ mount //srv//share /mnt/1 -o ...
mount: Invalid argument
The -EINVAL was returned correctly although the client only realised
it after sending a couple of bad requests rather than bailing out
earlier when parsing mount options.
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66be5c48ee upstream.
Chech the session state and skip it if it's exiting.
Signed-off-by: Winston Wen <wentao@uniontech.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f2a0afa98 upstream.
Some servers may return error codes from REQ_GET_DFS_REFERRAL requests
that are unexpected by the client, so to make it easier, assume
non-DFS mounts when the client can't get the initial DFS referral of
@ctx->UNC in dfs_mount_share().
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8f6446b68 ]
DMA direction should be taken in dma_unmap_page() for unmapping integrity
data.
Fix this DMA direction, and reported in Guangwu's test.
Reported-by: Guangwu Zhang <guazhang@redhat.com>
Fixes: 4aedb70543 ("nvme-pci: split metadata handling from nvme_map_data / nvme_unmap_data")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e337087c3 ]
Lion says:
-------
In the QFQ scheduler a similar issue to CVE-2023-31436
persists.
Consider the following code in net/sched/sch_qfq.c:
static int qfq_enqueue(struct sk_buff *skb, struct Qdisc *sch,
struct sk_buff **to_free)
{
unsigned int len = qdisc_pkt_len(skb), gso_segs;
// ...
if (unlikely(cl->agg->lmax < len)) {
pr_debug("qfq: increasing maxpkt from %u to %u for class %u",
cl->agg->lmax, len, cl->common.classid);
err = qfq_change_agg(sch, cl, cl->agg->class_weight, len);
if (err) {
cl->qstats.drops++;
return qdisc_drop(skb, sch, to_free);
}
// ...
}
Similarly to CVE-2023-31436, "lmax" is increased without any bounds
checks according to the packet length "len". Usually this would not
impose a problem because packet sizes are naturally limited.
This is however not the actual packet length, rather the
"qdisc_pkt_len(skb)" which might apply size transformations according to
"struct qdisc_size_table" as created by "qdisc_get_stab()" in
net/sched/sch_api.c if the TCA_STAB option was set when modifying the qdisc.
A user may choose virtually any size using such a table.
As a result the same issue as in CVE-2023-31436 can occur, allowing heap
out-of-bounds read / writes in the kmalloc-8192 cache.
-------
We can create the issue with the following commands:
tc qdisc add dev $DEV root handle 1: stab mtu 2048 tsize 512 mpu 0 \
overhead 999999999 linklayer ethernet qfq
tc class add dev $DEV parent 1: classid 1:1 htb rate 6mbit burst 15k
tc filter add dev $DEV parent 1: matchall classid 1:1
ping -I $DEV 1.1.1.2
This is caused by incorrectly assuming that qdisc_pkt_len() returns a
length within the QFQ_MIN_LMAX < len < QFQ_MAX_LMAX.
Fixes: 462dbc9101 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Reported-by: Lion <nnamrec@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 158810b261 ]
25369891fc deletes a check for the case where no 'lmax' is
specified which 3037933448 previously fixed as 'lmax'
could be set to the device's MTU without any bound checking
for QFQ_LMAX_MIN and QFQ_LMAX_MAX. Therefore, reintroduce the check.
Fixes: 25369891fc ("net/sched: sch_qfq: refactor parsing of netlink parameters")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4626cd04 ]
If there is a failure during rtw89_fw_h2c_raw() rtw89_debug_priv_send_h2c
should return negative error code instead of a positive value count.
Fix this bug by returning correct error code.
Fixes: e3ec7017f6 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/tencent_AD09A61BC4DA92AD1EB0790F5C850E544D07@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa846677a9 ]
For some device types like TXGBE_ID_XAUI, *checksum computed in
txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the
limit on the size of *checksum.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Fixes: 5e2ea7801f ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 150e33e62c ]
Eric Dumazet says[1]:
-------
Speaking of psched_mtu(), I see that net/sched/sch_pie.c is using it
without holding RTNL, so dev->mtu can be changed underneath.
KCSAN could issue a warning.
-------
Annotate dev->mtu with READ_ONCE() so KCSAN don't issue a warning.
[1] https://lore.kernel.org/all/CANn89iJoJO5VtaJ-2=_d2aOQhb0Xw8iBT_Cxqp2HyuS-zj6azw@mail.gmail.com/
v1 -> v2: Fix commit message
Fixes: d4b36210c2 ("net: pkt_sched: PIE AQM scheme")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230711021634.561598-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 835a65f517 ]
1ba6113a90a0 removed a lot of the kernel GPU channel, but method 0x128
was important as otherwise the GPU spams us with `CACHE_ERROR` messages.
We use the blit subchannel inside our vblank handling, so we should keep
at least this part.
v2: Only do it for NV11+ GPUs
Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/201
Fixes: 4a16dd9d18 ("drm/nouveau/kms: switch to drm fbdev helpers")
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526091052.2169044-1-kherbst@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f72207a5c0 ]
The simple_write_to_buffer() function is designed to handle partial
writes. It returns negatives on error, otherwise it returns the number
of bytes that were able to be copied. This code doesn't check the
return properly. We only know that the first byte is written, the rest
of the buffer might be uninitialized.
There is no need to use the simple_write_to_buffer() function.
Partial writes are prohibited by the "if (*ppos != 0)" check at the
start of the function. Just use memdup_user() and copy the whole
buffer.
Fixes: d3cbb907ae ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/7c1f950b-3a7d-4252-82a6-876e53078ef7@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b690e266da ]
lkp reports below sparse warning when building for RV32:
arch/riscv/mm/init.c:1204:48: sparse: warning: cast truncates bits from
constant value (100000000 becomes 0)
IMO, the reason we didn't see this truncates bug in real world is "0"
means MEMBLOCK_ALLOC_ACCESSIBLE in memblock and there's no RV32 HW
with more than 4GB memory.
Fix it anyway to make sparse happy.
Fixes: decf89f86e ("riscv: try to allocate crashkern region from 32bit addressible memory")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306080034.SLiCiOMn-lkp@intel.com/
Link: https://lore.kernel.org/r/20230709171036.1906-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3f87278bc ]
The kernel does not currently validate that both the minimum and maximum
ports of a port range are specified. This can lead user space to think
that a filter matching on a port range was successfully added, when in
fact it was not. For example, with a patched (buggy) iproute2 that only
sends the minimum port, the following commands do not return an error:
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass
# tc filter show dev swp1 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
filter protocol ip pref 1 flower chain 0 handle 0x2
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: gact action pass
random type none pass val 0
index 2 ref 1 bind 1
Fix by returning an error unless both ports are specified:
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp src_port 100-200 action pass
Error: Both min and max source ports must be specified.
We have an error talking to the kernel
# tc filter add dev swp1 ingress pref 1 proto ip flower ip_proto udp dst_port 100-200 action pass
Error: Both min and max destination ports must be specified.
We have an error talking to the kernel
Fixes: 5c72299fba ("net: sched: cls_flower: Classify packets using port ranges")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e06c57d66 ]
Currently, verifier does not reject XDP programs that pass NULL pointer to
hints functions. At the same time, this case is not handled in any driver
implementation (including veth). For example, changing
bpf_xdp_metadata_rx_timestamp(ctx, ×tamp);
to
bpf_xdp_metadata_rx_timestamp(ctx, NULL);
in xdp_metadata test successfully crashes the system.
Add KF_TRUSTED_ARGS flag to hints kfunc definitions, so driver code
does not have to worry about getting invalid pointers.
Fixes: 3d76a4d3d4 ("bpf: XDP metadata RX kfuncs")
Reported-by: Stanislav Fomichev <sdf@google.com>
Closes: https://lore.kernel.org/bpf/ZKWo0BbpLfkZHbyE@google.com/
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/r/20230711105930.29170-1-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9373771aae ]
Quieten a gcc (11.3.0) build error or warning by checking the function
call status and returning -EBUSY if the function call failed.
This is similar to what several other wireless drivers do for the
SIOCGIWRATE ioctl call when there is a locking problem.
drivers/net/wireless/cisco/airo.c: error: 'status_rid.currentXmitRate' is used uninitialized [-Werror=uninitialized]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/39abf2c7-24a-f167-91da-ed4c5435d1c4@linux-m68k.org
Link: https://lore.kernel.org/r/20230709133154.26206-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18bddc5b67 ]
DAX can be used to share page cache between VMs, reducing guest memory
overhead. And chunk based data format is widely used for VM and
container image. So enable dax support for it, make erofs better used
for VM scenarios.
Fixes: c5aa903a59 ("erofs: support reading chunk-based uncompressed files")
Signed-off-by: Xin Yin <yinxin.x@bytedance.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230711062130.7860-1-yinxin.x@bytedance.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8191213a58 ]
z_erofs_do_read_page() may loop infinitely due to the inappropriate
truncation in the below statement. Since the offset is 64 bits and min_t()
truncates the result to 32 bits. The solution is to replace unsigned int
with a 64-bit type, such as erofs_off_t.
cur = end - min_t(unsigned int, offset + end - map->m_la, end);
- For example:
- offset = 0x400160000
- end = 0x370
- map->m_la = 0x160370
- offset + end - map->m_la = 0x400000000
- offset + end - map->m_la = 0x00000000 (truncated as unsigned int)
- Expected result:
- cur = 0
- Actual result:
- cur = 0x370
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Fixes: 3883a79abd ("staging: erofs: introduce VLE decompression support")
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230710093410.44071-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 936aa701d8 ]
z_erofs_pcluster_readmore() may take a long time to loop when the page
offset is large enough, which is unnecessary should be prevented.
For example, when the following case is encountered, it will loop 4691368
times, taking about 27 seconds:
- offset = 19217289215
- inode_size = 1442672
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Fixes: 386292919c ("erofs: introduce readmore decompression strategy")
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230710042531.28761-1-guochunhai@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8278ee2a26 ]
Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting
such rules.
Fixes: dce677da57 ("octeontx2-pf: Add vlan-etype to ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04499f28b4 ]
Remove unnecessary of_node_put from the continue path to prevent
child node from being released twice, which could avoid resource
leak or other unexpected issues.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Fixes: de879a016a ("net: dsa: felix: add functionality when not all ports are supported")
Link: https://lore.kernel.org/r/20230710031859.36784-1-luhongfei@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113899c266 ]
Commit a4d86249c7 ("drm/i915/gt: Provide a utility to create a scratch
buffer") mistakenly passed in uapi I915_CACHING_CACHED as argument to
i915_gem_object_set_cache_coherency(), which actually takes internal
enum i915_cache_level.
No functional issue since the value matches I915_CACHE_LLC (1 == 1), which
is the intended caching mode, but lets clean it up nevertheless.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: a4d86249c7 ("drm/i915/gt: Provide a utility to create a scratch buffer")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230707125503.3965817-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 49c60b2f08)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c413188c6 ]
If we are using Bigjoiner dpll_hw_state is supposed to be exactly
same as for master crtc, so no need to save it's state for slave crtc.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 0ff0e219d9 ("drm/i915: Compute clocks earlier")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230628141017.18937-1-stanislav.lisovskiy@intel.com
(cherry picked from commit cbaf758809)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56b3c6ba53 ]
When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.
After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.
This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f7973990 ]
Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.
[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec
Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc638eabfe ]
The last_bdp is initialized to bdp, and both last_bdp and bdp are
not changed. That is to say that last_bdp and bdp are always equal.
So bdp can be used directly.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230529022615.669589-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: 20f7973990 ("net: fec: recycle pages for transmitted XDP frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ae9c66b04 ]
This patch is a cleanup for fec driver. The fec_enet_reset_skb()
is used to free skb buffers for tx queues and is only invoked in
fec_restart(). However, fec_enet_bd_init() also resets skb buffers
and is invoked in fec_restart() too. So fec_enet_reset_skb() is
redundant and useless.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 20f7973990 ("net: fec: recycle pages for transmitted XDP frames")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c56fb2aab2 ]
In order to generate the prologue and epilogue, the BPF JIT needs to
know which registers that are clobbered. Therefore, the during
pre-final passes, the prologue is generated after the body of the
program body-prologue-epilogue. Then, in the final pass, a proper
prologue-body-epilogue JITted image is generated.
This scheme has worked most of the time. However, for some large
programs with many jumps, e.g. the test_kmod.sh BPF selftest with
hardening enabled (blinding constants), this has shown to be
incorrect. For the final pass, when the proper prologue-body-epilogue
is generated, the image has not converged. This will lead to that the
final image will have incorrect jump offsets. The following is an
excerpt from an incorrect image:
| ...
| 3b8: 00c50663 beq a0,a2,3c4 <.text+0x3c4>
| 3bc: 0020e317 auipc t1,0x20e
| 3c0: 49630067 jalr zero,1174(t1) # 20e852 <.text+0x20e852>
| ...
| 20e84c: 8796 c.mv a5,t0
| 20e84e: 6422 c.ldsp s0,8(sp) # Epilogue start
| 20e850: 6141 c.addi16sp sp,16
| 20e852: 853e c.mv a0,a5 # Incorrect jump target
| 20e854: 8082 c.jr ra
The image has shrunk, and the epilogue offset is incorrect in the
final pass.
Correct the problem by always generating proper prologue-body-epilogue
outputs, which means that the first pass will only generate the body
to track what registers that are touched.
Fixes: 2353ecc6f9 ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230710074131.19596-1-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dceaafd668 ]
With commit 27267655c5 ("openrisc: Support floating point user api") I
added an entry to the struct sigcontext which caused an unwanted change
to the userspace ABI.
To fix this we use the previously unused oldmask field space for the
floating point fpcsr state. We do this with a union to restore the ABI
back to the pre kernel v6.4 ABI and keep API compatibility.
This does mean if there is some code somewhere that is setting oldmask
in an OpenRISC specific userspace sighandler it would end up setting the
floating point register status, but I think it's unlikely as oldmask was
never functional before.
Fixes: 27267655c5 ("openrisc: Support floating point user api")
Reported-by: Szabolcs Nagy <nsz@port70.net>
Closes: https://lore.kernel.org/openrisc/20230626213840.GA1236108@port70.net/
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bcc62858d ]
The insertion of an empty frame was introduced with
commit db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1bca9ac0b ]
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b86f10ab6 ]
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END
prevent the packet transmission over slot and cycle boundaries.
This is important for taprio offload where the slots and
cycles correspond to the slots and cycles configured for the
network.
However, the Qbv offload feature of the i225 is also used for
enabling TX launchtime / ETF offload. In that case, however,
the cycle has no meaning for the network and is only used
internally to adapt the base time register after a second has
passed.
Enabling strict mode in this case would unnecessarily prevent
the transmission of certain packets (i.e. at the boundary of a
second) and thus interferes with the ETF qdisc that promises
transmission at a certain point in time.
Similar to ETF, this also applies to CBS offload that also should
not be influenced by strict mode unless taprio offload would be
enabled at the same time.
This fully reverts
commit d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
but its commit message only describes what was already implemented
before that commit. The difference to a plain revert of that commit
is that it now copes with the base_time = 0 case that was fixed with
commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
In particular, enabling strict mode leads to TX hang situations
under high traffic if taprio is applied WITHOUT taprio offload
but WITH ETF offload, e.g. as in
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <d0>
TDT <f0>
next_to_use <f0>
next_to_clean <d0>
buffer_info[next_to_clean]
time_stamp <ffff661f>
next_to_watch <00000000245a4efb>
jiffies <ffff6e48>
desc.status <1048000>
Fixes: d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf0a624dc7 ]
The enable_trace_eprobe() function enables all event probes, attached
to given trace probe. If an error occurs in enabling one of the event
probes, all others should be roll backed. There is a bug in that roll
back logic - instead of all event probes, only the failed one is
disabled.
Link: https://lore.kernel.org/all/20230703042853.1427493-1-tz.stoyanov@gmail.com/
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 7491e2c442 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Tzvetomir Stoyanov (VMware) <tz.stoyanov@gmail.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82ff5f29b7 ]
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8046063df8 ]
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d800bc500 ]
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 8046063df8 ("igc: Rename qbv_enable to taprio_offload_enable")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 028e6e204a ]
The while-loop may break on one of the two conditions, either ID string
is empty or GUID matches. The second one, may never be reached if the
parsed string is not correct GUID. In such a case the loop will never
advance to check the next ID.
Break possible infinite loop by factoring out guid_parse_and_compare()
helper which may be moved to the generic header for everyone later on
and preventing from similar mistake in the future.
Interestingly that firstly it appeared when WMI was turned into a bus
driver, but later when duplicated GUIDs were checked, the while-loop
has been replaced by for-loop and hence no mistake made again.
Fixes: a48e23385f ("platform/x86: wmi: add context pointer field to struct wmi_device_id")
Fixes: 844af950da ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-1-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
