In preparation for adding the missing SPI and I2C nodes to
sc8280xp.dtsi, it was decided to rename all of the existing qupX_
uart, spi, and i2c nodes to drop the qupX_ prefix. Let's go ahead
and rename qup2_uart17 to uart17. Note that some nodes are moved in the
file by this patch to preserve the expected sort order in the file.
Signed-off-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/lkml/20221212182314.1902632-1-bmasney@redhat.com/
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230103182229.37169-4-bmasney@redhat.com
Some lines were broken very aggresively, presumably to fit under 80 chars
and some places could have used a newline, particularly between subsequent
nodes. Address all that and remove redundant comments near PCIe ranges
while at it so as not to exceed 100 chars needlessly.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-5-konrad.dybcio@linaro.org
The dwc3 subnode was indented using spaces for some reason and other
properties were not exactly properly indented. Fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230102094642.74254-3-konrad.dybcio@linaro.org
Enable PCIe controllers and PHYs nodes on SM8550 MTP board.
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118230526.1499328-3-abel.vesa@linaro.org
This adds support for the aDSP, cDSP and MPSS Subsystems found in
the SM8550 SoC.
The aDSP, cDSP and MPSS needs:
- smp2p nodes to get event back from the subsystems
- remoteproc nodes with glink-edge subnodes providing all needed
resources to start and run the subsystems
In addition, the MPSS Subsystem needs a rmtfs_mem dedicated
memory zone.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115-topic-sm8550-upstream-dts-remoteproc-v3-2-815a1753de34@linaro.org
Add nodes for the Visionox VTDR6130 found on the SM8550-MTP
device.
TLMM states are also added for the Panel reset GPIO and
Tearing Effect signal for when the panel is running in
DSI Command mode.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-3-1729cfc0e5db@linaro.org
Add devices tree nodes describing display hardware on SM8550:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on the SM8550.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104-topic-sm8550-upstream-dts-display-v4-1-1729cfc0e5db@linaro.org
Currently, available frequencies for all CPUs are appearing as 2x
of the actual frequencies. Use xo clock source as bi_tcxo in the
cpufreq-hw node to fix this.
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117093533.3710000-1-quic_pkondeti@quicinc.com
The MUIC installed is a part of SM5703 MFD, and it seems to work
the same as the SM5502 MUIC unit.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
[Apply for msm8916-samsung-j5x]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143051.547302-1-linmengbo0689@protonmail.com
Samsung Galaxy J5 2015 and 2016 have a Hall sensor on GPIO pin 52.
Add GPIO Hall sensor for them.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143037.547248-1-linmengbo0689@protonmail.com
After moving msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi,
Add new J5 2016 device tree.
[Add j5x device tree]
Co-developed-by: Josef W Menad <JosefWMenad@protonmail.ch>
Signed-off-by: Josef W Menad <JosefWMenad@protonmail.ch>
[Use &pm8916_usbin as USB extcon and add chassis-type for j5x]
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Use common init device tree]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143024.547194-1-linmengbo0689@protonmail.com
The smartphones below are using the MSM8916 SoC,
which are released in 2015-2016:
Samsung Galaxy J5 2015 (SM-J500*)
Samsung Galaxy J5 2016 (SM-J510*)
Move msm8916-samsung-j5.dts to msm8916-samsung-j5-common.dtsi, and add
a common device tree for with initial support for:
- GPIO keys
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5703 MUIC)
- WCNSS (WiFi/BT)
- Regulators
The two devices (all other variants of J5 released in 2015 and J5X
released in 2016) are very similar, with some differences in display and
GPIO pins. The common parts are shared in msm8916-samsung-j5-common.dtsi
to reduce duplication.
This patch rewrites J5 2015 devices, later patches will add support for
other models.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106143010.547140-1-linmengbo0689@protonmail.com
IPA is used for mobile data. Add a node describing it.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104193759.3286014-2-elder@linaro.org
Add the CPU OPP tables including core frequency and L3 bus frequency.
The L3 throughput values were chosen by studying the frequencies
available in HW LUT and picking the highest one that's less than the
CPU frequency. DDR clock rates come from the vendor kernel.
Available values from the HW LUT:
300000000
556800000
652800000
806400000
844800000
940800000
1132800000
1209600000
1286400000
1401600000
1459200000
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230104171643.1004054-3-konrad.dybcio@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-19-dmitry.baryshkov@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-18-dmitry.baryshkov@linaro.org
Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-17-dmitry.baryshkov@linaro.org
The slope values used during tsens calibration differ between msm8976
and msm8956 SoCs. Use SoC-specific compat value for the msm8956 SoC.
Fixes: 0484d3ce09 ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-16-dmitry.baryshkov@linaro.org
Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used. To date, this has been
indicated by the presence or absence of a "modem-init" property.
That mechanism has been deprecated. Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.
Update all arm64 platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.
Update the affected nodes so the status property is last.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[bjorn: Moved sc7280 change herobrine-lte-sku]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-3-elder@linaro.org
Bindings expect each pin config to come with a "function" property:
sc7280-crd-r3.dtb: pinctrl@f100000: amp-en-state: 'oneOf' conditional failed, one must be fixed:
'function' is a required property
'bias-pull-down', 'drive-strength', 'pins' do not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-9-krzysztof.kozlowski@linaro.org
Correct typo in motor pinctrl node name:
msm8916-samsung-a5u-eur.dtb: pinctrl@1000000: 'motor-en-default-stae' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-8-krzysztof.kozlowski@linaro.org
The cluster idle issue was resolved on SM8250, so the change disabling
the cluster state is being reverted.
Issues where identified with the QMP PHY binding, that would prevent
enablement of Displayport and it was decided not to support the old
binding for the recently introduced SC8280XP, which broke USB. This
adjusts the USB PHY nodes to the new binding. The reset signal for the
first QMP PHY is corrected as well.
The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus 6P,
to avoid instabilities caused by use of protected memory regions.
The compatible for the MSM8992 TCSR mutex is corrected as well.
Lastly SDHCI interconnects on SM8350 are corrected to match the
providers #interconnect-cells.
-----BEGIN PGP SIGNATURE-----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=ZCnd
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-6.2' into arm64-for-6.3
Qualcomm ARM64 DTS fixes for 6.2
The cluster idle issue was resolved on SM8250, so the change disabling
the cluster state is being reverted.
Issues where identified with the QMP PHY binding, that would prevent
enablement of Displayport and it was decided not to support the old
binding for the recently introduced SC8280XP, which broke USB. This
adjusts the USB PHY nodes to the new binding. The reset signal for the
first QMP PHY is corrected as well.
The reserved memory map is updated on Xiaomi Mi 4C and Huawei Nexus 6P,
to avoid instabilities caused by use of protected memory regions.
The compatible for the MSM8992 TCSR mutex is corrected as well.
Lastly SDHCI interconnects on SM8350 are corrected to match the
providers #interconnect-cells.
Use two interconnect cells in order to optionally
support a path tag.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117115712.1054613-1-rfoss@kernel.org
While booting the CRD, a series of CMA allocation errors can be seen in
the kernel log:
cma: cma_alloc: reserved: alloc failed, req-size: 128 pages, ret: -12
Growing the CMA region and querying /proc/meminfo indicates that a newly
booted system (currently) uses 64MB CMA.
Define a memory region sufficiently large for the current use cases, to
avoid forcing users to add this themselves, through command line
parameters etc.
While fixing the CRD define the same region for the X13s.
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sc8280xp-lenovo-thinkpad-x13s
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117184630.2775905-1-quic_bjorande@quicinc.com
