[ Upstream commit a62d196e89 ]
corePWM is capable of inverted operation but the binding requires
\#pwm-cells of 2. Expand the binding to support setting the polarity.
Fixes: df77f77357 ("dt-bindings: pwm: add microchip corepwm binding")
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ac909916b ]
The preferred form for Renesas' compatible strings is:
"<vendor>,<family>-<module>"
Somehow the compatible string for the r9a09g011 I2C IP was upstreamed
as renesas,i2c-r9a09g011 instead of renesas,r9a09g011-i2c, which
is really confusing, especially considering the generic fallback
is renesas,rzv2m-i2c.
The first user of renesas,i2c-r9a09g011 in the kernel is not yet in
a kernel release, it will be in v6.1, therefore it can still be
fixed in v6.1.
Even if we don't fix it before v6.2, I don't think there is any
harm in making such a change.
s/renesas,i2c-r9a09g011/renesas,r9a09g011-i2c/g for consistency.
Fixes: 54ac6794df ("arm64: dts: renesas: r9a09g011: Add i2c nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221107165027.54150-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278f5015a3 ]
Although the HW User Manual for RZ/V2M states in the "Address Map"
section that the interrupt controller is assigned addresses starting
from 0x82000000, the memory locations from 0x82000000 0x0x8200FFFF
are marked as reserved in the "Interrupt Controller (GIC)" section
and are currently not used by the device tree, leading to the below
warning:
arch/arm64/boot/dts/renesas/r9a09g011.dtsi:51.38-63.5: Warning
(simple_bus_reg): /soc/interrupt-controller@82000000: simple-bus unit
address format error, expected "82010000"
Fix the unit address accordingly.
Fixes: fb1929b98f ("arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221103230648.53748-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64416ef0b0 ]
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the SCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: c62331e822 ("arm64: dts: renesas: Add Renesas R8A779F0 SoC support")
Fixes: 4075314425 ("arm64: dts: renesas: r8a779f0: Add SCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5101ef18b ]
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the HSCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 01a787f78b ("arm64: dts: renesas: r8a779f0: Add HSCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de1172624 ]
SM6125 comes with SDCC (SDHCI controller) v5, so the second range of
registers is cqhci, not core.
Fixes: cff4bbaf2a ("arm64: dts: qcom: Add support for SM6125")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # Sony Xperia 10 II
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026163646.37433-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7860f575 ]
As idr_alloc() and of_property_read_string_index() can return negative
numbers, it should be better to check the return value and deal with
the exception.
Therefore, it should be better to use goto statement to stop and return
error.
Fixes: 6adba21eb4 ("soc: qcom: Add APR bus driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107014403.3606-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95fade4016 ]
The QMP pipe clock is used by the USB part of the PHY so drop the
corresponding properties from the DP child node.
Fixes: 23737b9557 ("arm64: dts: qcom: sm6350: Add USB1 nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026152511.9661-3-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9f23e46d ]
The QMP pipe clock is used by the USB part of the PHY so drop the
corresponding properties from the DP child node.
Fixes: 5aa0d1becd ("arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026152511.9661-2-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8f298d4f6 ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: f8b4eb64f2 ("arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0/2.0 and IDP boards")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-5-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1caf66104c ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: 0a3a56a93f ("arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-4-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d9fcbb3e ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: 36c9d012f1 ("arm64: dts: qcom: use GPIO flags for tlmm")
Fixes: 5a263cf629 ("arm64: dts: qcom: sm8250-mtp: Add wcd9380 audio codec node")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-3-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76d21ffc5d ]
When resetting the block, the reset line is being driven low and then
high, which means that the line in DTS should be annotated as "active
low". It will become important when wcd9335 driver will be converted
to gpiod API that respects declared line polarities.
Fixes: f3eb39a55a ("arm64: dts: db820c: Add sound card support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-1-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af949211a ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 07fa917a33 ("arm64: dts: qcom: sm8450: add ufs nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-5-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3c7839b69 ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 59c7cf8147 ("arm64: dts: qcom: sm8350: Add UFS nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-4-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f8b37dd4e ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: b7e2fba066 ("arm64: dts: qcom: sm8250: Add UFS controller and PHY")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-3-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36a31b3a8d ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 3834a2e922 ("arm64: dts: qcom: sm8150: Add ufs nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-2-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c882c899ea ]
The function platform_get_irq prints an error message into the kernel
log when the irq isn't found.
Since the interrupt is actually optional and not provided by some SoCs,
use platform_get_irq_optional which does not print an error message.
Fixes: c081f3060f ("soc: qcom: Add support to register LLCC EDAC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104153041.412020-1-luca.weiss@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59e787935c ]
The Trogdor Homestar DTSI adds additional GPIO52 pin to secondary I2S pins
("sec_mi2s_active") and configures it to "mi2s_1" function.
The Trogdor DTSI (which is included by Homestar) configures drive
strength and bias for all "sec_mi2s_active" pins, thus the intention was
to apply this configuration also to GPIO52 on Homestar.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: be0416a3f9 ("arm64: dts: qcom: Add sc7180-trogdor-homestar")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6105a8b7c ]
Evidently I forgot to update the unit address for the 38-bit cached
memory node when I changed the address in the reg property..
Update it to match.
Fixes: 6c11933017 ("riscv: dts: microchip: update memory configuration for v2022.10")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13b2c3e0e ]
Commit b9e8a7d950 ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950 ("firmware: ti_sci: Switch transport to polled mode during system suspend")
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adf85adc2a ]
There is a sparse warning shown below:
drivers/soc/ti/knav_qmss_queue.c:70:12: warning: symbol
'knav_acc_firmwares' was not declared. Should it be static?
Since 'knav_acc_firmwares' is only called within knav_qmss_queue.c,
mark it as static to fix the warning.
Fixes: 96ee19becc ("soc: ti: add firmware file name as part of the driver")
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221019153212.72350-1-chenjiahao16@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d577e3d5 ]
The WLAN regulator uses 'gpios' property instead of 'gpio' to specify
regulator enable GPIO. While the former is also currently handled by
the Linux kernel regulator-fixed driver, the later is the correct one
per DT bindings. Update the DT to use the later.
Fixes: 7dd5cbba42 ("ARM: dts: stm32: Enable WiFi on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b835f1b8a ]
The Avenger96 is populated with STM32MP157A DHCOR SoM, drop the
stm32mp15xc.dtsi which should only be included in DTs of devices
which are populated with STM32MP15xC/F SoC as the stm32mp15xc.dtsi
enables CRYP block not present in the STM32MP15xA/D SoC .
Fixes: 7e76f82acd ("ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63646fcba5 ]
Adds KCSAN's volatile instrumentation to objtool's uaccess whitelist.
Recent kernel change have shown that this was missing from the uaccess
whitelist (since the first upstreamed version of KCSAN):
mm/gup.o: warning: objtool: fault_in_readable+0x101: call to __tsan_volatile_write1() with UACCESS enabled
Fixes: 75d75b7a4d ("kcsan: Support distinguishing volatile accesses")
Signed-off-by: Marco Elver <elver@google.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5192481f90 ]
According to the datasheet, HS bit should be specified to 1 when using
DMA transfer. As DMA transfer is not supported, it should be cleared to
0.
Previously, the driver relied on the HS bit being cleared by prior
firmware but this is not always the case.
Fix this by ensuring the bit is cleared during hardware initialization.
Fixes: ca7d8b980b ("memory: add Renesas RPC-IF driver")
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/08d9fb10b3051decebf871267a6e2e7cb2d4faf9.1665583089.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574d6c59da ]
Drive strength macros defined for FSD platform is not reflecting actual
names and values as per HW UM. FSD SoC pinctrl has following four levels
of drive-strength and their corresponding values:
Level-1 <-> 0
Level-2 <-> 1
Level-4 <-> 2
Level-6 <-> 3
The commit 684dac402f ("arm64: dts: fsd: Add initial pinctrl support")
used drive strength macros defined for Exynos4 SoC family. For some IPs
the macros values of Exynos4 matched and worked well, but Exynos4 SoC
family drive-strength (names and values) is not exactly matching with
FSD SoC.
Fix the drive strength macros to reflect actual names and values given
in FSD HW UM.
Fixes: 684dac402f ("arm64: dts: fsd: Add initial pinctrl support")
Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20221013104024.50179-2-p.rajanbabu@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff02ac6216 ]
MSM8916 was originally using the "qcom,q6v5-pil" compatible for the
MSS remoteproc. Later it was decided to use SoC-specific compatibles
instead, so "qcom,msm8916-mss-pil" is now the preferred compatible.
Commit 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific
compatibles to SCM/MSS") updated the MSM8916 device tree to make use of
the new compatible but still kept the old "qcom,q6v5-pil" as fallback.
This is inconsistent with other SoCs and conflicts with the description
in the binding documentation (which says that only one compatible should
be present). Also, it has no functional advantage since older kernels
could not handle this DT anyway (e.g. "power-domains" in the MSS node is
only supported by kernels that also support "qcom,msm8916-mss-pil").
Make this consistent with other SoCs by using only the
"qcom,msm8916-mss-pil" compatible.
Fixes: 60a05ed059 ("arm64: dts: qcom: msm8916: Add MSM8916-specific compatibles to SCM/MSS")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718140344.1831731-2-stephan.gerhold@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d440d811e ]
Fix Adreno OPP table according to the msm-3.18. Enable 624 MHz for the
speed bin 3 and 560 MHz for bins 2 and 3.
Fixes: 69cc3114ab ("arm64: dts: Add Adreno GPU definitions")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724140421.1933004-7-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0154caaa2b ]
Adjust MSM8996 cpufreq tables according to tables in msm-3.18. Some of
the frequencies are not supported on speed bins other than 0. Also other
speed bins support intermediate topmost frequencies, not supported on
speed bin 0. Implement all these differencies.
Fixes: 90173a954a ("arm64: dts: qcom: msm8996: Add CPU opps")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724140421.1933004-5-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8898c9748a ]
Qualcomm MSM8996 Pro is a variant of MSM8996 with higher frequencies
supported both on CPU and GPU. There are other minor hardware
differencies in the CPU and GPU regulators and bus fabrics.
However this results in significant differences between 8996 and 8996
Pro CPU OPP tables. Judging from msm-3.18 there are only few common
frequencies supported by both msm8996 and msm8996pro. Rather than
hacking the tables for msm8996, split msm8996pro support into a separate
file. Later this would allow having additional customizations for the
CBF, CPR, retulators, etc.
[DB: dropped all non-CPU-OPP changes]
Fixes: 90173a954a ("arm64: dts: qcom: msm8996: Add CPU opps")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
[DB: Realigned supported-hw to keep compat with current cpufreq driver]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724140421.1933004-3-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58c4a0b6f4 ]
Fix typo in the codec's pin name to be configured. Mismatched name
caused the pin configuration to be ignored.
Fixes: be497abe19 ("arm64: dts: qcom: Add support for Xiaomi Mi Mix2s")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Molly Sophia <mollysophia379@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220930192039.240486-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4290d407a ]
As serial communication requires a clock signal, the High Speed Serial
Communication Interfaces with FIFO (HSCIF) are clocked by a clock that
is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the HSCIF0 Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car V4H Hardware User's Manual rev. 0.54.
Fixes: 987da486d8 ("arm64: dts: renesas: Add Renesas R8A779G0 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a5bd4148f92806f7c8e577d383370f810315f586.1665155947.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecec4b20d2 ]
The checks for musb->xceiv and musb->xceiv->set_power duplicate those in
usb_phy_set_power(), so there is no need of them. Moreover, not calling
usb_phy_set_power() results in usb_phy_set_charger_current() not being
called, so current USB config max current is not propagated through USB
charger framework and charger drivers may try to draw more current than
allowed or possible.
Fix that by removing those extra checks and calling usb_phy_set_power()
directly.
Tested on Motorola Droid4 and Nokia N900
Fixes: a9081a008f ("usb: phy: Add USB charger support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Link: https://lore.kernel.org/r/1669400475-4762-1-git-send-email-ivo.g.dimitrov.75@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ca637c0ece upstream.
The reset line is called PWRST#, annotated as "active low" in the
binding documentation, and is driven low and then high by the driver to
reset the chip. However in device tree for CI20 board it was incorrectly
marked as "active high". Fix it.
Because (as far as I know) the ci20.dts is always built in the kernel I
elected not to also add a quirk to gpiolib to force the polarity there.
Fixes: db49ca3857 ("net: davicom: dm9000: switch to using gpiod API")
Reported-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5adedd4224 upstream.
Commit cd3bc044af ("KEYS: encrypted: Instantiate key with
user-provided decrypted data") added key instantiation with user
provided decrypted data. The user data is hex-ascii-encoded but was
just memcpy'ed to the binary buffer. Fix this to use hex2bin instead.
Old keys created from user provided decrypted data saved with "keyctl
pipe" are still valid, however if the key is recreated from decrypted
data the old key must be converted to the correct format. This can be
done with a small shell script, e.g.:
BROKENKEY=abcdefABCDEF1234567890aaaaaaaaaa
NEWKEY=$(echo -ne $BROKENKEY | xxd -p -c32)
keyctl add user masterkey "$(cat masterkey.bin)" @u
keyctl add encrypted testkey "new user:masterkey 32 $NEWKEY" @u
However, NEWKEY is still broken: If for BROKENKEY 32 bytes were
specified, a brute force attacker knowing the key properties would only
need to try at most 2^(16*8) keys, as if the key was only 16 bytes long.
The security issue is a result of the combination of limiting the input
range to hex-ascii and using memcpy() instead of hex2bin(). It could
have been fixed either by allowing binary input or using hex2bin() (and
doubling the ascii input key length). This patch implements the latter.
The corresponding test for the Linux Test Project ltp has also been
fixed (see link below).
Fixes: cd3bc044af ("KEYS: encrypted: Instantiate key with user-provided decrypted data")
Cc: stable@kernel.org
Link: https://lore.kernel.org/ltp/20221006081709.92303897@mail.steuer-voss.de/
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Nikolaus Voss <nikolaus.voss@haag-streit.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7f291e14d upstream.
When running xfstests against Azure the following oops occurred on an
arm64 system
Unable to handle kernel write to read-only memory at virtual address
ffff0001221cf000
Mem abort info:
ESR = 0x9600004f
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x0f: level 3 permission fault
Data abort info:
ISV = 0, ISS = 0x0000004f
CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=00000000294f3000
[ffff0001221cf000] pgd=18000001ffff8003, p4d=18000001ffff8003,
pud=18000001ff82e003, pmd=18000001ff71d003, pte=00600001221cf787
Internal error: Oops: 9600004f [#1] PREEMPT SMP
...
pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
pc : __memcpy+0x40/0x230
lr : scatterwalk_copychunks+0xe0/0x200
sp : ffff800014e92de0
x29: ffff800014e92de0 x28: ffff000114f9de80 x27: 0000000000000008
x26: 0000000000000008 x25: ffff800014e92e78 x24: 0000000000000008
x23: 0000000000000001 x22: 0000040000000000 x21: ffff000000000000
x20: 0000000000000001 x19: ffff0001037c4488 x18: 0000000000000014
x17: 235e1c0d6efa9661 x16: a435f9576b6edd6c x15: 0000000000000058
x14: 0000000000000001 x13: 0000000000000008 x12: ffff000114f2e590
x11: ffffffffffffffff x10: 0000040000000000 x9 : ffff8000105c3580
x8 : 2e9413b10000001a x7 : 534b4410fb86b005 x6 : 534b4410fb86b005
x5 : ffff0001221cf008 x4 : ffff0001037c4490 x3 : 0000000000000001
x2 : 0000000000000008 x1 : ffff0001037c4488 x0 : ffff0001221cf000
Call trace:
__memcpy+0x40/0x230
scatterwalk_map_and_copy+0x98/0x100
crypto_ccm_encrypt+0x150/0x180
crypto_aead_encrypt+0x2c/0x40
crypt_message+0x750/0x880
smb3_init_transform_rq+0x298/0x340
smb_send_rqst.part.11+0xd8/0x180
smb_send_rqst+0x3c/0x100
compound_send_recv+0x534/0xbc0
smb2_query_info_compound+0x32c/0x440
smb2_set_ea+0x438/0x4c0
cifs_xattr_set+0x5d4/0x7c0
This is because in scatterwalk_copychunks(), we attempted to write to
a buffer (@sign) that was allocated in the stack (vmalloc area) by
crypt_message() and thus accessing its remaining 8 (x2) bytes ended up
crossing a page boundary.
To simply fix it, we could just pass @sign kmalloc'd from
crypt_message() and then we're done. Luckily, we don't seem to pass
any other vmalloc'd buffers in smb_rqst::rq_iov...
Instead, let's map the correct pages and offsets from vmalloc buffers
as well in cifs_sg_set_buf() and then avoiding such oopses.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f05f80f217 upstream.
The device ID 0xa70e is defined for the USB3 device controller in the CPU
sub-system of Raptor Lake platform. Hence updating the ID accordingly.
Fixes: bad0d1d726 ("usb: dwc3: pci: Add support for Intel Raptor Lake")
Cc: stable <stable@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20221125105327.27945-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0dced9c7d upstream.
It can take more than one second to check each connector
when the system is resumed. So if you have, say, eight
connectors, it may take eight seconds for ucsi_resume() to
finish. That's a bit too much.
This will modify ucsi_resume() so that it schedules a work
where the interface is actually resumed instead of checking
the connectors directly. The connections will also be
checked in separate tasks which are queued for each connector
separately.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216706
Fixes: 99f6d43611 ("usb: typec: ucsi: Check the connection on resume")
Cc: <stable@vger.kernel.org>
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20221123093021.25981-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
