The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Fix up the two paths in the freescale callback that failed to re-enable
interrupts when polling.
Fixes: 853a9ae29e ("serial: 8250: fix handle_irq locking")
Cc: stable@vger.kernel.org # 5.13
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y/xYzqp4ogmOF5t0@kili
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230227085046.24282-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per HW manual for EMEV2 "R19UH0040EJ0400 Rev.4.00", the UART
IP found on EMMA mobile SoC is Register-compatible with the
general-purpose 16750 UART chip. Fix UART port type as 16750 and
enable 64-bytes fifo support.
Fixes: 22886ee968 ("serial8250-em: Emma Mobile UART driver V2")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230227114152.22265-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: 8d310c9107 ("drivers/tty/serial/8250: Make Aspeed VUART SIRQ polarity configurable")
Cc: stable <stable@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oskar Senft <osk@google.com>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-9-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to skip
waiting for transmission complete when UARTCTRL_SBK is asserted,
otherwise the kernel may stuck here.
And actually set_termios() adds transmission completion waiting to avoid
data loss or data breakage when changing the baud rate, but we don't
need to worry about this when queuing break characters.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230223093941.31790-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5779a072c2.
This results in a link error of
ld: drivers/tty/serial/earlycon.o: in function `parse_options':
drivers/tty/serial/earlycon.c:99: undefined reference to `uart_parse_earlycon'
When the config is in this state
CONFIG_SERIAL_CORE=m
CONFIG_SERIAL_CORE_CONSOLE=y
CONFIG_SERIAL_EARLYCON=y
CONFIG_SERIAL_FSL_LPUART=m
CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
Fixes: 5779a072c2 ("tty: serial: fsl_lpuart: adjust SERIAL_FSL_LPUART_CONSOLE config dependency")
Cc: stable <stable@kernel.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230226173846.236691-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux/fs.h has a wrapper for this operation.
Signed-off-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230306075527.1338-1-zbestahu@gmail.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
When neither "no_read_workqueue" nor "no_write_workqueue" are enabled,
tasklet_trylock() in crypt_dec_pending() may still return false due to
an uninitialized state, and dm-crypt will unnecessarily do io completion
in io_queue workqueue instead of current context.
Fix this by adding an 'in_tasklet' flag to dm_crypt_io struct and
initialize it to false in crypt_io_init(). Set this flag to true in
kcryptd_queue_crypt() before calling tasklet_schedule(). If set
crypt_dec_pending() will punt io completion to a workqueue.
This also nicely avoids the tasklet_trylock/unlock hack when tasklets
aren't in use.
Fixes: 8e14f61015 ("dm crypt: do not call bio_endio() from the dm-crypt tasklet")
Cc: stable@vger.kernel.org
Reported-by: Hou Tao <houtao1@huawei.com>
Suggested-by: Ignat Korchagin <ignat@cloudflare.com>
Reviewed-by: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
They are used during the erofs module init phase. Let's mark it as
__init like any other function.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230303063731.66760-1-frank.li@vivo.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Some boards might use USB-A female connector for USB ports, however,
the port could be connected to a dual-mode USB controller, making it
also behaves as a peripheral device if male-to-male cable is connected.
In this case, the dts looks like this:
&usb0 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
role-switch-default-mode = "host";
};
After boot, dwc2_ovr_init() sets GOTGCTL to GOTGCTL_AVALOVAL and call
dwc2_force_mode() with parameter host=false, which causes inconsistent
mode - The hardware is in peripheral mode while the kernel status is
in host mode.
What we can do now is to call dwc2_drd_role_sw_set() to switch to
device mode, and everything should work just fine now, even switching
back to none(default) mode afterwards.
Fixes: e14acb8769 ("usb: dwc2: drd: add role-switch-default-node support")
Cc: stable <stable@kernel.org>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/SG2PR01MB204837BF68EDB0E343D2A375C9A59@SG2PR01MB2048.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i.MX8MQ use Synopsys DesignWare USB3 Controller IP, so add the
compatible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230203014526.1461386-1-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some __dynamic_array() buffer will only used at trace event output time,
change to __get_buf() which will allocate tempary trace seq buffer for
output purpose.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1677465850-1396-5-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some __dynamic_array() buffer will only used at trace event output time,
change to __get_buf() which will allocate tempary trace seq buffer for
output purpose.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677465850-1396-4-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
some __dynamic_array() buffer will only used at trace event output time,
change to __get_buf() which will allocate tempary trace seq buffer for
output purpose.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1677465850-1396-3-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the original design seem have several problems, first during trace event
output stage, cdns3_dbg_ring() still refer to priv_ep->trb_pool which
data content may changed during runtime, second when ring number is
greater than TRBS_PER_SEGMENT, it has no change to show "too big" message,
third in cdns3_log_ring event class definition, it allocate too much trace
event buffer.
change cdns3_dbg_ring() to be called at trace event fast assign time, and
change trace buffer real dynamic according ring numbers.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1677465850-1396-2-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the USB gadget framework supports only version 1.0 of the MS OS
descriptor. OS desc has a field bcdVersion indicating its version, with
v1.0 represented by the value 0x100. However, __ffs_do_os_desc_header()
was expecting the incorrect value 0x1, so allow the correct value 0x100.
The bcdVersion field of the descriptor that is actually sent to the host
is set by composite_setup() (in composite.c) to the fixed value 0x100.
Therefore, it can be understood that __ffs_do_os_desc_header() is only
performing a format check of the OS desc passed to functionfs. If a value
other than 0x100 is accepted, there is no effect on communication over
the USB bus. Indeed, until now __ffs_do_os_desc_header() has only accepted
the incorrect value 0x1, but there was no problem with the communication
over the USB bus.
However, this can be confusing for functionfs userspace drivers. Since
bcdVersion=0x100 is used in actual communication, functionfs should accept
the value 0x100.
Note that the correct value for bcdVersion in OS desc v1.0 is 0x100, but
to avoid breaking old userspace drivers, the value 0x1 is also accepted as
an exception. At this time, a message is output to notify the user to fix
the userspace driver.
Signed-off-by: Yuta Hayama <hayama@lineo.co.jp>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/290f96db-1877-5137-373a-318e7b4f2dde@lineo.co.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a bug by making sure prev_err doesn't get used when being
uninitialized.
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Fixes: 9e622229bb ("mmc: starfive: Add sdio/emmc driver support")
Link: https://lore.kernel.org/r/20230307024646.10216-3-william.qiu@starfivetech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we don't change the current value if device isn't in
configured state. But in battery charging specification (section
1.2 and 1.4.13), it is mentioned that the device can draw up to
100mA of current if it's in unconfigured state. Hence add vbus
draw work in composite_resume to draw 100mA if the device isn't
configured.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1677217619-10261-3-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we process the suspend interrupt event only if the
device is in configured state. Consider a case where device
is not configured and got suspend interrupt, in that case our
gadget will still use 100mA as composite_suspend didn't happen.
But battery charging specification (BC1.2) expects a downstream
device to draw less than 2.5mA when unconnected OR suspended.
Fix this by removing the condition for processing suspend event,
and thus composite_resume would set vbus draw to 2.
Fixes: 72704f876f ("dwc3: gadget: Implement the suspend entry event handler")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1677217619-10261-2-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lower the power-on failed message severity from warn to info when the
controller does not power-up. It's normal to have this situation when
the SD card slot is empty, therefore we should not warn the user about
it.
Fixes: 7ca0f166f5 ("mmc: sdhci_am654: Add workaround for card detect debounce timer")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230306162751.163369-1-francesco@dolcini.it
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some ULPI USB PHY does not support internal VBUS supply, to drive the CPEN
pin, which requires the configuration of the ULPI DRVVBUSEXTERNAL bit of
OTG_CTRL register.
Added 'snps,ulpi-ext-vbus-drv' a DT property to configure the USB2 PHY to
drive VBUS with an external supply, by setting the USB2 PHY ULPIEXTVBUSDRV
bit[:17] of the GUSB2PHYCFG register to drive VBUS with an external supply.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20230215093146.5812-3-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ULPI USB PHYs do not support an internal vBus supply, to drive the
CPEN pin properly, it requires configuration of the ULPI DRVVBUSEXTERNAL
bit of the USB ULPI PHY OTG_CTRL register.
Added 'snps,ulpi-ext-vbus-drv' DT property to configure the USB2 PHY to
drives VBUS with an external supply.
When the ULPIEXTVBUSDRV bit is set to '1' in the Global USB2 PHY
Configuration registers, PHY drive vBus with an external 5V supply source.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230215093146.5812-2-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This binding uses usb-hcd.yaml so replace additionalProperties with
unevaluatedProperties to allow generic USB HCD properties. It's how EHCI
and XHCI bindings work too.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230228152105.25358-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This binding was originally meant to describe hard-wired USB devices but
in some situations we need to describe USB ports. That is needed e.g. if
USB port is meant to be used as a trigger source but it can have any
device plugged. It's a common case for home routers which have USB ports
(with no hard-wired devices) and USB LEDs to indicate ports state.
There is no point (and no easy way) to add separate binding covering
just USB ports. Adjust existing devices binding to allow describing
ports.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@21000: port@1: 'compatible' is a required property
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@21000: port@2: 'compatible' is a required property
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@21000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'port@1', 'port@2' were unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ehci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@22000: port@1: 'compatible' is a required property
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@22000: port@2: 'compatible' is a required property
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@22000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'port@1', 'port@2' were unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-ohci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@23000: port@1: 'compatible' is a required property
From schema: Documentation/devicetree/bindings/usb/generic-xhci.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: usb@23000: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'phy-names', 'phys', 'port@1' were unexpected)
From schema: Documentation/devicetree/bindings/usb/generic-xhci.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230228182909.1011-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3 USB Linux driver and several DTS use extcon property, so
document it, even though it is deprecated, to fix warnings like:
sm6125-sony-xperia-seine-pdx201.dtb: usb@4ef8800: usb@4e00000: Unevaluated properties are not allowed ('extcon' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230304130302.51497-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230307163041.3815-12-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230307163041.3815-11-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Loading V3 firmware does not need a quirk anymore, remove the leftover
code.
Fixes: ed8603e111 ("usb: host: xhci-rcar: Simplify getting the firmware name for R-Car Gen3")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230307163041.3815-10-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Transform zero-length array into flexible-array member in struct
ehci_regs.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
drivers/usb/host/oxu210hp-hcd.c:3983:30: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3986:38: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3971:30: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3978:30: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3523:30: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:2774:39: warning: array subscript port is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3569:35: warning: array subscript <unknown> is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:3888:36: warning: array subscript port is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
drivers/usb/host/oxu210hp-hcd.c:2911:45: warning: array subscript i is outside array bounds of ‘u32[0]’ {aka ‘unsigned int[]’} [-Warray-bounds=]
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/259
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/Y/gynI9Wv8RZTD8M@work
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers generally shouldn't be using of_irq_parse_one() directly as it
is a low-level interrupt parsing API. The exceptions are cases that need
the values from the 'interrupts' property.
This is not the case for Tegra XHCI driver as it just uses
of_irq_parse_one() to test for 'interrupts' being absent or invalid.
Instead, just make the interrupt optional on any error other than
deferred probe. The exact reason for failing to get the interrupt is not
that important.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230228235322.13289-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Steam Deck bios old properties. If a Steam deck didn't
upgrade the BIOS, the driver should be able to handle the previous
properties for shared boost types.
Signed-off-by: Lucas Tanure <lucas.tanure@collabora.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230309140051.945329-1-lucas.tanure@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
This series introduces an abstraction of the HDA DAI handling.
The motivation is to simplify and make the code more flexible regarding to IPC
versions, new features (ChainDMA (IPC4) and DSPless mode) and to pave the way for new
platforms.
For the first look the series might feels a bit too intrusive but it introduces
no functionality change (tested at each commit).
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Link: https://lore.kernel.org/r/20230308202117.426808-2-nick.alcock@oracle.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Since commit 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations
are used to identify modules. As a consequence, uses of the macro
in non-modules will cause modprobe to misidentify their containing
object file as a module when it is not (false positives), and modprobe
might succeed rather than failing with a suitable error message.
So remove it in the files in this commit, none of which can be built as
modules.
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230308202117.426808-1-nick.alcock@oracle.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The UVC Gadget function has become quite complex, but documentation
for it is fairly sparse. Add some more detailed documentation to
improve the situation.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Link: https://lore.kernel.org/r/20230308165213.139315-1-dan.scally@ideasonboard.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel will dump in the below cases:
sysfs: cannot create duplicate filename
'/devices/virtual/usb_power_delivery/pd1/source-capabilities'
1. After soft reset has completed, an Explicit Contract negotiation occurs.
The sink device will receive source capabilitys again. This will cause
a duplicate source-capabilities file be created.
2. Power swap twice on a device that is initailly sink role.
This will unregister existing capabilities when above cases occurs.
Fixes: 8203d26905 ("usb: typec: tcpm: Register USB Power Delivery Capabilities")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230215054951.238394-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm version of gpiochip add function to handle removal for us.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the unbind callback for f_uac1 and f_uac2, a call to snd_card_free()
via g_audio_cleanup() will disconnect the card and then wait for all
resources to be released, which happens when the refcount falls to zero.
Since userspace can keep the refcount incremented by not closing the
relevant file descriptor, the call to unbind may block indefinitely.
This can cause a deadlock during reboot, as evidenced by the following
blocked task observed on my machine:
task:reboot state:D stack:0 pid:2827 ppid:569 flags:0x0000000c
Call trace:
__switch_to+0xc8/0x140
__schedule+0x2f0/0x7c0
schedule+0x60/0xd0
schedule_timeout+0x180/0x1d4
wait_for_completion+0x78/0x180
snd_card_free+0x90/0xa0
g_audio_cleanup+0x2c/0x64
afunc_unbind+0x28/0x60
...
kernel_restart+0x4c/0xac
__do_sys_reboot+0xcc/0x1ec
__arm64_sys_reboot+0x28/0x30
invoke_syscall+0x4c/0x110
...
The issue can also be observed by opening the card with arecord and
then stopping the process through the shell before unbinding:
# arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
Recording WAVE '/dev/null' : Signed 32 bit Little Endian, Rate 48000 Hz, Stereo
^Z[1]+ Stopped arecord -D hw:UAC2Gadget -f S32_LE -c 2 -r 48000 /dev/null
# echo gadget.0 > /sys/bus/gadget/drivers/configfs-gadget/unbind
(observe that the unbind command never finishes)
Fix the problem by using snd_card_free_when_closed() instead, which will
still disconnect the card as desired, but defer the task of freeing the
resources to the core once userspace closes its file descriptor.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20230302163648.3349669-1-alvin@pqrs.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Microchip USB2517 USB 2.0 hub to the onboard usb hub
driver. Adopt the generic usb-device compatible ("usbVID,PID").
This hub has the same reset timings as USB2514, so reuse that one.
There is also an USB2517I which just has industrial temperature range.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230223073920.2912298-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, there was a 100uS delay inserted after issuing an end transfer
command for specific controller revisions. This was due to the fact that
there was a GUCTL2 bit field which enabled synchronous completion of the
end transfer command once the CMDACT bit was cleared in the DEPCMD
register. Since this bit does not exist for all controller revisions and
the current implementation heavily relies on utizling the EndTransfer
command completion interrupt, add the delay back in for uses where the
interrupt on completion bit is not set, and increase the duration to 1ms
for the controller to complete the command.
An issue was seen where the USB request buffer was unmapped while the DWC3
controller was still accessing the TRB. However, it was confirmed that the
end transfer command was successfully submitted. (no end transfer timeout)
In situations, such as dwc3_gadget_soft_disconnect() and
__dwc3_gadget_ep_disable(), the dwc3_remove_request() is utilized, which
will issue the end transfer command, and follow up with
dwc3_gadget_giveback(). At least for the USB ep disable path, it is
required for any pending and started requests to be completed and returned
to the function driver in the same context of the disable call. Without
the GUCTL2 bit, it is not ensured that the end transfer is completed before
the buffers are unmapped.
Fixes: cf2f8b63f7 ("usb: dwc3: gadget: Remove END_TRANSFER delay")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230306200557.29387-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://lore.kernel.org/r/20230306144641.21955-1-quic_mdalam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently only one stream is supported. This isn't usally a problem
until you have a multi codec audio card. Because the audio card will run
startup and shutdown on both capture and playback streams. So if your
hdmi-codec only support either playback or capture. Then ALSA can't open
for playback and capture.
This patch will ignore if startup and shutdown are called with a non
supported stream. Thus, allowing an audio card like this:
+-+
cpu1 <--@-| |-> codec1 (HDMI-CODEC)
| |<- codec2 (NOT HDMI-CODEC)
+-+
Signed-off-by: Emil Svendsen <emas@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20230309065432.4150700-2-emas@bang-olufsen.dk
Signed-off-by: Mark Brown <broonie@kernel.org>