Commit graph

1,215,304 commits

Author SHA1 Message Date
Konrad Dybcio
fd888ed763 arm64: dts: qcom: qrb4210-rb2: Add GPIO LEDs
Add the three LEDs (blue/yellow/green) connected to TLMM GPIOs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-and-Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515-topic-rb2-bits-v1-3-a52d154a639d@linaro.org
2023-05-23 06:26:11 -07:00
Konrad Dybcio
f7b01e07e8 arm64: dts: qcom: qrb4210-rb2: Enable display out
The RB2 has a HDMI output via an LT9611UXC bridge. Set it up.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-and-Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515-topic-rb2-bits-v1-2-a52d154a639d@linaro.org
2023-05-23 06:26:11 -07:00
Konrad Dybcio
e130889286 arm64: dts: qcom: qrb4210-rb2: Describe fixed regulators
The board hosts a whole lot of fixed regulators. Describe them.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-and-Tested-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515-topic-rb2-bits-v1-1-a52d154a639d@linaro.org
2023-05-23 06:24:47 -07:00
Krzysztof Kozlowski
d97a6332c5 arm64: dts: qcom: sm8550-qrd: add USB OTG
Add missing parts of USB stack to enable USB OTG mode.  The QRD8550
comes with one USB Type-C port.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516133011.108093-2-krzysztof.kozlowski@linaro.org
2023-05-23 06:24:07 -07:00
Krzysztof Kozlowski
b8ae83eb0c arm64: dts: qcom: sm8550-qrd: add PCIe0
Add PCIe0 nodes used with WCN7851 device.  The PCIe1 is not connected,
thus skip pcie_1_phy_aux_clk input clock to GCC.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516133011.108093-1-krzysztof.kozlowski@linaro.org
2023-05-23 06:24:07 -07:00
Luke D. Jones
e6c7e2711d HID: asus: reformat the hotkey mapping block
Older formatting of this block was beginning to get somewhat cluttered.
Condensing the block and putting comments to the side makes it easier
to read and scan the scancodes plus keycodes.

Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:17:24 +02:00
Luke D. Jones
73920f6151 HID: asus: add keycodes for 0x6a, 0x4b, and 0xc7
These two keys are found on some models with dual display.
- 0x6a is intended for controlling the secondary screen brightness.
- 0x4b is intended for toggling the arrow keys between arrows and
  page up / page down.
This key is found on a slightly modified keyboard layout.
- 0xc7 is intended to cycle through keybvoard brightnesses (upwards) but
  there is not suitable existing code for this behaviour. Using
  `KEY_KBDILLUMTOGGLE` is different behaviour to Windows but at least
  is picked up by many desktops already.

Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:17:24 +02:00
Luke D. Jones
74e47b2c52 HID: asus: Add support for ASUS ROG Z13 keyboard
Add support for the ROG Z13 keyboard. This is a variant of the last
few ASUS ROG keyboards and has much of the same functionality.

Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:17:24 +02:00
Denis Arefev
16a9c24f24 HID: wacom: Add error check to wacom_parse_and_register()
Added a variable check and
   transition in case of an error

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:11:57 +02:00
Sung-Chi Li
ed84c4517a HID: google: add jewel USB id
Add 1 additional hammer-like device.

Signed-off-by: Sung-Chi Li <lschyi@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:09:24 +02:00
Nikita Zhandarovich
bd249b9197 HID: wacom: avoid integer overflow in wacom_intuos_inout()
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.

Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.

Fixes: 3bea733ab2 ("USB: wacom tablet driver reorganization")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:08:23 +02:00
Jason Gerecke
d9eef346b6 HID: wacom: Check for string overflow from strscpy calls
The strscpy function is able to return an error code when a copy would
overflow the size of the destination. The copy is stopped and the buffer
terminated before overflow actually occurs so it is safe to continue
execution, but we should still produce a warning should this occur.

Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2023-05-23 15:06:36 +02:00
Rander Wang
1b167ba8a2
ASoC: SOF: Intel: tgl: unify core_put on IPC3 & IPC4 path
Firmware may do context saving before powering off primary core, so driver
needs to send ipc msg by set_core_state. In IPC4 path, firmware needs to
save current context to IMR before powering off primary core. Firmware
does nothing for set_core_state message in IPC3 path. So IPC4 and IPC3
can share the same operation sequence.

Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230523103217.20412-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-05-23 13:56:00 +01:00
Rander Wang
c6d15567a4
ASoC: SOF: Intel: mtl: add core_get & put support on MeterLake platforms
In core_get case, driver can power up primary core and don't need to send
ipc message to fw. Non-primary core should be powered up by fw with ipc
message.

In core_put case, driver should first send ipc message to fw to disable dsp
core then power down primary core if the target is primary core.

Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230523103217.20412-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-05-23 13:55:59 +01:00
Claudiu Beznea
a9392efae9
ASoC: use pm.h instead of runtime_pm.h
Do not include pm_runtime.h header in files where runtime PM support is
not implemented. Use pm.h instead as suspend to RAM specific
implementation is available.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230517094903.2895238-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-05-23 13:55:56 +01:00
Claudiu Beznea
2f3092e77f
ASoC: do not include pm_runtime.h if not used
Do not include pm_runtime.h header in files where APIs exported by
pm_runtime.h are not used.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> # for omap-mcbsp-st.c
Link: https://lore.kernel.org/r/20230517094903.2895238-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-05-23 13:55:55 +01:00
Thomas Zimmermann
b0c536d88e drm/msm: Use struct fb_info.screen_buffer
The fbdev framebuffer is in system memory. Store the address in
the field 'screen_buffer'. Fixes the following sparse warning.

../drivers/gpu/drm/msm/msm_fbdev.c:124:26: warning: incorrect type in assignment (different address spaces)
../drivers/gpu/drm/msm/msm_fbdev.c:124:26:    expected char [noderef] __iomem *screen_base
../drivers/gpu/drm/msm/msm_fbdev.c:124:26:    got void *

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230522191701.13406-1-tzimmermann@suse.de
2023-05-23 14:50:37 +02:00
Thomas Zimmermann
aa25aacc3e drm/gma500: Clear fbdev framebuffer with fb_memset_io()
The fbdev framebuffer is I/O memory, so clear it with fb_memset_io().
Fixes the following sparse warning:

../drivers/gpu/drm/gma500/fbdev.c:234:20: warning: incorrect type in argument 1 (different address spaces)
../drivers/gpu/drm/gma500/fbdev.c:234:20:    expected void *s
../drivers/gpu/drm/gma500/fbdev.c:234:20:    got char [noderef] __iomem *screen_base

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230522190637.7039-1-tzimmermann@suse.de
2023-05-23 14:50:26 +02:00
Neil Armstrong
b002bac7b4 arm64: dts: qcom: sm8450-hdk: Add QMP & DP to SuperSpeed graph
With support for the QMP combo phy to react to USB Type-C switch events,
introduce it as the next hop for the SuperSpeed lanes of the Type-C
connector, and connect the output of the DisplayPort controller
to the QMP combo phy.

This allows the TCPM to perform orientation switching of both USB and
DisplayPort signals.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-4-6c43d293995f@linaro.org
2023-05-23 05:37:53 -07:00
Neil Armstrong
a3e42da4f7 arm64: dts: qcom: sm8350-hdk: Add QMP & DP to SuperSpeed graph
With support for the QMP combo phy to react to USB Type-C switch events,
introduce it as the next hop for the SuperSpeed lanes of the Type-C
connector, and connect the output of the DisplayPort controller
to the QMP combo phy.

This allows the TCPM to perform orientation switching of both USB and
DisplayPort signals.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-3-6c43d293995f@linaro.org
2023-05-23 05:37:53 -07:00
Neil Armstrong
e5167da381 arm64: dts: qcom: sm8450: add ports subnodes in usb1 qmpphy node
Add the USB3+DP Combo QMP PHY port subnodes in the SM8450 SoC DTSI
to avoid duplication in the devices DTs.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-2-6c43d293995f@linaro.org
2023-05-23 05:37:53 -07:00
Neil Armstrong
d831312557 arm64: dts: qcom: sm8350: add ports subnodes in usb1 qmpphy node
Add the USB3+DP Combo QMP PHY port subnodes in the SM8350 SoC DTSI
to avoid duplication in the devices DTs.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-1-6c43d293995f@linaro.org
2023-05-23 05:37:53 -07:00
Neil Armstrong
5294c2d78f arm64: defconfig: enable FSA4480 driver as module
Enable the FSA4480 driver as module for Qualcomm HDK8350 and HDK8450
platforms to permit USB-C Altmode support.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-5-6c43d293995f@linaro.org
2023-05-23 05:37:33 -07:00
Neil Armstrong
4b11fa4f07 qcom: pmic_glink: enable altmode for SM8450
Create a separate bitmask for sm8550 and enable altmode aux driver
for sm8450 platform to enable pmic-glink altmode events.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230503-topic-sm8450-graphics-dp-next-v3-6-6c43d293995f@linaro.org
2023-05-23 05:37:12 -07:00
Bjorn Andersson
de6d1f0c49 dt-bindings: clock: qcom: Accept power-domains for GPUCC
In many designs the power-domains provided by the GPU clock controller
are powered by some GFX rail, add power-domains as a valid property to
allow this to be specified.

Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230523010348.63043-1-quic_bjorande@quicinc.com
2023-05-23 05:35:44 -07:00
Takashi Iwai
03a58514d4 Merge branch 'topic/midi20' into for-next
This is a (largish) patch set for adding the support of MIDI 2.0
functionality, mainly targeted for USB devices.  MIDI 2.0 is a
complete overhaul of the 40-years old MIDI 1.0.  Unlike MIDI 1.0 byte
stream, MIDI 2.0 uses packets in 32bit words for Universal MIDI Packet
(UMP) protocol.  It supports both MIDI 1.0 commands for compatibility
and the extended MIDI 2.0 commands for higher resolutions and more
functions.

For supporting the UMP, the patch set extends the existing ALSA
rawmidi and sequencer interfaces, and adds the USB MIDI 2.0 support to
the standard USB-audio driver.

The rawmidi for UMP has a different device name (/dev/snd/umpC*D*) and
it reads/writes UMP packet data in 32bit CPU-native endianness.  For
the old MIDI 1.0 applications, the legacy rawmidi interface is
provided, too.

As default, USB-audio driver will take the alternate setting for MIDI
2.0 interface, and the compatibility with MIDI 1.0 is provided via the
rawmidi common layer.  However, user may let the driver falling back
to the old MIDI 1.0 interface by a module option, too.

A UMP-capable rawmidi device can create the corresponding ALSA
sequencer client(s) to support the UMP Endpoint and UMP Group
connections.  As a nature of ALSA sequencer, arbitrary connections
between clients/ports are allowed, and the ALSA sequencer core
performs the automatic conversions for the connections between a new
UMP sequencer client and a legacy MIDI 1.0 sequencer client.  It
allows the existing application to use MIDI 2.0 devices without
changes.

The MIDI-CI, which is another major extension in MIDI 2.0, isn't
covered by this patch set.  It would be implemented rather in
user-space.

Roughly speaking, the first half of this patch set is for extending
the rawmidi and USB-audio, and the second half is for extending the
ALSA sequencer interface.

The patch set is based on 6.4-rc2 kernel, but all patches can be
cleanly applicable on 6.2 and 6.3 kernels, too (while 6.1 and older
kernels would need minor adjustment for uapi header changes).

The updates for alsa-lib and alsa-utils will follow shortly later.

The author thanks members of MIDI Association OS/API Working Group,
especially Andrew Mee, for great helps for the initial design and
debugging / testing the drivers.

Link: https://lore.kernel.org/r/20230523075358.9672-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 14:14:47 +02:00
Oswald Buddenhagen
7195fb46da ALSA: emu10k1: pass raw FX send config to snd_emu10k1_pcm_init_voice()
... instead of passing in a high-level mixer struct. Let the
higher-level functions handle the differences between the voice types.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 14:14:01 +02:00
Oswald Buddenhagen
f5192e3381 ALSA: emu10k1: introduce higher-level voice manipulation functions
This adds snd_emu10k1_pcm_init_{voices,extra_voice}() and
snd_emu10k1_playback_{un,}mute_voices() to slightly abstract by voice
function and potential stereo property.

Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 14:13:38 +02:00
Arnd Bergmann
e34cd89a6a platform/x86: lenovo-yogabook: add I2C dependency
The added platform_driver support fails to link when I2C core support is
not rechable:

x86_64-linux-ld: drivers/platform/x86/lenovo-yogabook.o: in function `yogabook_pdev_probe':
lenovo-yogabook.c:(.text+0x5a5): undefined reference to `i2c_bus_type'

Add a Kconfig dependency to enforce a working configuration.

Fixes: 6df1523fa0 ("platform/x86: lenovo-yogabook: Add platform driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230519082606.375471-1-arnd@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-23 13:04:30 +02:00
Horatiu Vultur
6007612459 lan966x: Fix unloading/loading of the driver
It was noticing that after a while when unloading/loading the driver and
sending traffic through the switch, it would stop working. It would stop
forwarding any traffic and the only way to get out of this was to do a
power cycle of the board. The root cause seems to be that the switch
core is initialized twice. Apparently initializing twice the switch core
disturbs the pointers in the queue systems in the HW, so after a while
it would stop sending the traffic.
Unfortunetly, it is not possible to use a reset of the switch here,
because the reset line is connected to multiple devices like MDIO,
SGPIO, FAN, etc. So then all the devices will get reseted when the
network driver will be loaded.
So the fix is to check if the core is initialized already and if that is
the case don't initialize it again.

Fixes: db8bcaad53 ("net: lan966x: add the basic lan966x driver")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230522120038.3749026-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-05-23 13:01:06 +02:00
David Arcari
3279decb2c platform/x86/intel/ifs: Annotate work queue on stack so object debug does not complain
Object Debug results in the following warning while attempting to load
ifs firmware:

[  220.007422] ODEBUG: object 000000003bf952db is on stack 00000000e843994b, but NOT annotated.
[  220.007459] ------------[ cut here ]------------
[  220.007461] WARNING: CPU: 0 PID: 11774 at lib/debugobjects.c:548 __debug_object_init.cold+0x22e/0x2d5
[  220.137476] RIP: 0010:__debug_object_init.cold+0x22e/0x2d5
[  220.254774] Call Trace:
[  220.257641]  <TASK>
[  220.265606]  scan_chunks_sanity_check+0x368/0x5f0 [intel_ifs]
[  220.288292]  ifs_load_firmware+0x2a3/0x400 [intel_ifs]
[  220.332793]  current_batch_store+0xea/0x160 [intel_ifs]
[  220.357947]  kernfs_fop_write_iter+0x355/0x530
[  220.363048]  new_sync_write+0x28e/0x4a0
[  220.381226]  vfs_write+0x62a/0x920
[  220.385160]  ksys_write+0xf9/0x1d0
[  220.399421]  do_syscall_64+0x59/0x90
[  220.440635]  entry_SYSCALL_64_after_hwframe+0x63/0xcd
[  220.566845] ---[ end trace 3a01b299db142b41 ]---

Correct this by calling INIT_WORK_ONSTACK instead of INIT_WORK.

Fixes: 684ec21570 ("platform/x86/intel/ifs: Authenticate and copy to secured memory")

Signed-off-by: David Arcari <darcari@redhat.com>
Cc: Jithu Joseph <jithu.joseph@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230523105400.674152-1-darcari@redhat.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-23 12:55:16 +02:00
Steve Wahl
bbb320bfe2 platform/x86: ISST: Remove 8 socket limit
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot().  Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.

On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.

Fixes: aa2ddd2425 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-05-23 12:52:05 +02:00
Takashi Iwai
6b39e30dce ALSA: docs: Add MIDI 2.0 documentation
Add the brief document for describing the MIDI 2.0 implementation on
Linux kernel.  Both rawmidi and sequencer API extensions are
described.

Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-38-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:40 +02:00
Takashi Iwai
d2b7060777 ALSA: seq: Add UMP group filter
Add a new filter bitmap for UMP groups for reducing the unnecessary
read/write when the client is connected to UMP EP seq port.

The new group_filter field contains the bitmap for the groups, i.e.
when the bit is set, the corresponding group is filtered out and
the messages to that group won't be delivered.

The filter bitmap consists of each bit of 1-based UMP Group number.
The bit 0 is reserved for the future use.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-37-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:38 +02:00
Takashi Iwai
e85b926056 ALSA: seq: Print UMP Endpoint and Block information in proc outputs
This patch enhances the /proc/asound/seq/clients output to show a few
more information about the assigned UMP Endpoint and Blocks.

The "Groups" are shown in 1-based group number to align with the
sequencer client name and port number.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-36-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:38 +02:00
Takashi Iwai
d2d247e35e ALSA: seq: Add ioctls for client UMP info query and setup
Add new ioctls for sequencer clients to query and set the UMP endpoint
and block information.

As a sequencer client corresponds to a UMP Endpoint, one UMP Endpoint
information can be assigned at most to a single sequencer client while
multiple UMP block infos can be assigned by passing the type with the
offset of block id (i.e. type = block_id + 1).

For the kernel client, only SNDRV_SEQ_IOCTL_GET_CLIENT_UMP_INFO is
allowed.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-35-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:36 +02:00
Takashi Iwai
4025f0e627 ALSA: seq: ump: Create UMP Endpoint port for broadcast
Create a sequencer port for broadcasting the all group inputs at the
port number 0.  This corresponds to a UMP Endpoint connection;
application can read all UMP events from this port no matter which
group the UMP packet belongs to.

Unlike seq ports for other UMP groups, a UMP Endpoint port has no
SND_SEQ_PORT_TYPE_MIDI_GENERIC bit, so that it won't be treated as a
normal MIDI 1.0 device from legacy applications.

The port is named as "MIDI 2.0" to align with representations on other
operation systems.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-34-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:35 +02:00
Takashi Iwai
81fd444aa3 ALSA: seq: Bind UMP device
This patch introduces a new ALSA sequencer client for the kernel UMP
object, snd-seq-ump-client.  It's a UMP version of snd-seq-midi
driver, while this driver creates a sequencer client per UMP endpoint
which contains (fixed) 16 ports.

The UMP rawmidi device is opened in APPEND mode for output, so that
multiple sequencer clients can share the same UMP endpoint, as well as
the legacy UMP rawmidi devices that are opened in APPEND mode, too.
For input, on the other hand, the incoming data is processed on the
fly in the dedicated hook, hence it doesn't open a rawmidi device.

The UMP packet group is updated upon delivery depending on the target
sequencer port (which corresponds to the actual UMP group).

Each sequencer port sets a new port type bit,
SNDRV_SEQ_PORT_TYPE_MIDI_UMP, in addition to the other standard
types for MIDI.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-33-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:33 +02:00
Takashi Iwai
329ffe11a0 ALSA: seq: Allow suppressing UMP conversions
A sequencer client like seq_dummy rather doesn't want to convert UMP
events but receives / sends as is.  Add a new event filter flag to
suppress the automatic UMP conversion and applies accordingly.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-32-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:32 +02:00
Takashi Iwai
e9e02819a9 ALSA: seq: Automatic conversion of UMP events
This patch enables the automatic conversion of UMP events from/to the
legacy ALSA sequencer MIDI events.  Also, as UMP itself has two
different modes (MIDI 1.0 and MIDI 2.0), yet another converters
between them are needed, too.  Namely, we have conversions between the
legacy and UMP like:
  - seq legacy event -> seq UMP MIDI 1.0 event
  - seq legacy event -> seq UMP MIDI 2.0 event
  - seq UMP MIDI 1.0 event -> seq legacy event
  - seq UMP MIDI 2.0 event -> seq legacy event

and the conversions between UMP MIDI 1.0 and 2.0 clients like:
  - seq UMP MIDI 1.0 event -> seq UMP MIDI 2.0 event
  - seq UMP MIDI 2.0 event -> seq UMP MIDI 1.0 event

The translation is per best-effort; some MIDI 2.0 specific events are
ignored when translated to MIDI 1.0.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-31-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:28 +02:00
Takashi Iwai
a3ca3b3080 ALSA: seq: Add UMP group number to snd_seq_port_info
Add yet more new filed "ump_group" to snd_seq_port_info for specifying
the associated UMP Group number for each sequencer port.  This will be
referred in the upcoming automatic UMP conversion in sequencer core.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-30-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:27 +02:00
Takashi Iwai
ff166a9d19 ALSA: seq: Add port direction to snd_seq_port_info
Add a new field "direction" to snd_seq_port_info for allowing a client
to tell the expected direction of the port access.  A port might still
allow subscriptions for read/write (e.g. for MIDI-CI) even if the
primary usage of the port is a single direction (either input or
output only).  This new "direction" field can help to indicate such
cases.

When the direction is unspecified at creating a port and the port has
either read or write capability, the corresponding direction bits are
set automatically as default.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-29-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:25 +02:00
Takashi Iwai
177ccf811d ALSA: seq: Support MIDI 2.0 UMP Endpoint port
This is an extension to ALSA sequencer infrastructure to support the
MIDI 2.0 UMP Endpoint port.  It's a "catch-all" port that is supposed
to be present for each UMP Endpoint.  When this port is read via
subscription, it sends any events from all ports (UMP Groups) found in
the same client.

A UMP Endpoint port can be created with the new capability bit
SNDRV_SEQ_PORT_CAP_UMP_ENDPOINT.  Although the port assignment isn't
strictly defined, it should be the port number 0.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:24 +02:00
Takashi Iwai
74661932ac ALSA: seq: Add port inactive flag
This extends the ALSA sequencer port capability bit to indicate the
"inactive" flag.  When this flag is set, the port is essentially
invisible, and doesn't appear in the port query ioctls, while the
direct access and the connection to this port are still allowed.  The
active/inactive state can be flipped dynamically, so that it can be
visible at any time later.

This feature is introduced basically for UMP; some UMP Groups in a UMP
Block may be unassigned, hence those are practically invisible.  On
ALSA sequencer, the corresponding sequencer ports will get this new
"inactive" flag to indicate the invisible state.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-27-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:23 +02:00
Takashi Iwai
46397622a3 ALSA: seq: Add UMP support
Starting from this commit, we add the basic support of UMP (Universal
MIDI Packet) events on ALSA sequencer infrastructure.  The biggest
change here is that, for transferring UMP packets that are up to 128
bits, we extend the data payload of ALSA sequencer event record when
the client is declared to support for the new UMP events.

A new event flag bit, SNDRV_SEQ_EVENT_UMP, is defined and it shall be
set for the UMP packet events that have the larger payload of 128
bits, defined as struct snd_seq_ump_event.

For controlling the UMP feature enablement in kernel, a new Kconfig,
CONFIG_SND_SEQ_UMP is introduced.  The extended event for UMP is
available only when this Kconfig item is set.  Similarly, the size of
the internal snd_seq_event_cell also increases (in 4 bytes) when the
Kconfig item is set.  (But the size increase is effective only for
32bit architectures; 64bit archs already have padding there.)
Overall, when CONFIG_SND_SEQ_UMP isn't set, there is no change in the
event and cell, keeping the old sizes.

For applications that want to access the UMP packets, first of all, a
sequencer client has to declare the user-protocol to match with the
latest one via the new SNDRV_SEQ_IOCTL_USER_PVERSION; otherwise it's
treated as if a legacy client without UMP support.

Then the client can switch to the new UMP mode (MIDI 1.0 or MIDI 2.0)
with a new field, midi_version, in snd_seq_client_info.  When switched
to UMP mode (midi_version = 1 or 2), the client can write the UMP
events with SNDRV_SEQ_EVENT_UMP flag.  For reads, the alignment size
is changed from snd_seq_event (28 bytes) to snd_seq_ump_event (32
bytes).  When a UMP sequencer event is delivered to a legacy sequencer
client, it's ignored or handled as an error.

Conceptually, ALSA sequencer client and port correspond to the UMP
Endpoint and Group, respectively; each client may have multiple ports
and each port has the fixed number (16) of channels, total up to 256
channels.

As of this commit, ALSA sequencer core just sends and receives the UMP
events as-is from/to clients.  The automatic conversions between the
legacy events and the new UMP events will be implemented in a later
patch.

Along with this commit, bump the sequencer protocol version to 1.0.3.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:21 +02:00
Takashi Iwai
afb72505e4 ALSA: seq: Introduce SNDRV_SEQ_IOCTL_USER_PVERSION ioctl
For the future extension of ALSA sequencer ABI, introduce a new ioctl
SNDRV_SEQ_IOCTL_USER_PVERSION.  This is similar like the ioctls used
in PCM and other interfaces, for an application to specify its
supporting ABI version.

The use of this ioctl will be mandatory for the upcoming UMP support.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-25-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:19 +02:00
Takashi Iwai
1359905383 ALSA: seq: Prohibit creating ports with special numbers
Some port numbers are special, such as 254 for subscribers and 255 for
broadcast.  Return error if application tries to create such a port.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-24-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:19 +02:00
Takashi Iwai
4f92eb792e ALSA: seq: Check validity before creating a port object
The client type and the port info validity check should be done before
actually creating a port, instead of unnecessary create-and-scratch.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-23-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:18 +02:00
Takashi Iwai
7c3f0d3d3a ALSA: seq: Check the conflicting port at port creation
We didn't check if a port with the given port number has been already
present at creating a new port.  Check it and return -EBUSY properly
if the port number conflicts.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-22-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:17 +02:00
Takashi Iwai
94c5b717ad ALSA: seq: Drop dead code for the old broadcast support
The broadcast and multicast supports have been never enabled.
Let's drop the dead code.

Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230523075358.9672-21-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2023-05-23 12:11:16 +02:00