Only higher voltage sku can support HBR3 so a condition
check added in max source rate calculation for ehl/jsl.
Bspec: 32247, 20598
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-4-animesh.manna@intel.com
Combo phy is limited to 5.4 GHz on low-voltage SKUs. Combo phy DP is
limited to 5.4 GHz, while combo phy eDP can do 8.1 GHz.
Bspec: 20584, 20598, 49180, 49201
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-3-animesh.manna@intel.com
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before intel_encoder->type is set. This causes incorrect max source
rate to be used for display 11+. On EHL and JSL, HBR3 is used instead of
HBR2, and on the other affected platforms, HBR2 is used instead of HBR3.
Move intel_dp_set_source_rates() to after intel_encoder->type is
set. Add comment to intel_dp_is_edp() describing unsafe usages. Cleanup
intel_dp_init_connector() while at it.
Note: The same change was originally added as commit 680c45c767
("drm/i915/dp: Correctly advertise HBR3 for GEN11+"), but later reverted
due to issues in CI in commit d391301960 ("Revert "drm/i915/dp:
Correctly advertise HBR3 for GEN11+"").
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-2-animesh.manna@intel.com
Accidentally dropped the else in a rebase fail, causing the DG2 max rate
to be overwritten later in the if ladder.
Fixes: e752d1f9c1 ("drm/i915/dg2: add DG2 UHBR source rates")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901112815.16498-1-jani.nikula@intel.com
Enable MIPI DSI support on ADL-P platform.
The esc clock changes, WA changes are taken care
in the previous patches.
As per the Bspec the seq remains to be same as TGL.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-3-vandita.kulkarni@intel.com
Wa_16012360555 SW will have to program the "LP to HS Wakeup Guardband"
field to account for the repeaters on the HS Request/Ready PPI signaling
between the Display engine and the DPHY.
v2: Fix build issue.
v3: Align to new naming (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-2-vandita.kulkarni@intel.com
We had a mix of intel_edp_drrs_*(), intel_dp_drrs_*() and
intel_dp_set_drrs_state(), so properly renaming all functions to
keep the same pattern.
While at it, also dropping intel_dp_set_drrs_state from the
documentation as it is a static function.
v3:
- dropping documentation style comment in static function
(intel_drrs_set_state)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-3-jose.souza@intel.com
intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce
some lines from it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com
At this point is sure that HSW and BDW will never have PSR enabled by
default, so here dropping it from device info and cleaning up code.
v2:
- enable psr support for display 9
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-1-jose.souza@intel.com
UHBR modes has higher link rate and added new values for programming
mpll of SNPS phy. No change in sequence, only the pll parameters
are different for UHBR modes.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827103843.527-1-jani.nikula@intel.com
Apparently the last reader of i915->active_pipes was removed with commit
ef79d62b5c ("drm/i915: Encapsulate dbuf state handling harder"), and
now it's only ever written to. Remove it completely.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826141830.889-1-jani.nikula@intel.com
The memory latency values returned by pcode on DG2 are in units of "2
usec" rather than 1 usec on all other platforms. I.e., we need to
double the value returned by pcode to obtain the true latency value.
The bspec wording here was a bit ambiguous as to whether it wanted us to
multiply or divide the pcode value by two, but we confirmed offline with
the hardware team that we need to double the value the pcode gives us;
this change is intended to support a larger range of potential latency
values.
Bspec: 49326
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820225710.401136-1-matthew.d.roper@intel.com
On g4x and pch the DPLL has two P1 dividers (for refresh rate
switching). Program the FPx1 P1 divider consistently to the reduced
clock P1 divider if available, otherwise just program it to the
same value as the FPx0 P1 divider.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The current gen2 DPLL readout code:
* assumes i845/i865 have LVDS which is not true
* assumes only pipe B can drive LVDS (true, but makes
the code appear a bit magical)
* hard to parse in general
Clean it up by checking for i85x (the only gen2 platform
with LVDS) and reusing intel_lvds_port_enabled().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
When we enable the DPLL for the PPS kick, let's tell the DPLL code
we're dealing with an eDP output. This shouldn't really matter, but
it's more consistent with the way the DPLL is configured when we're
actually enabling the eDP port for real.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We don't care about __iomem mismatch when dealing with error
pointers. Silence it with ERR_CAST().
drivers/gpu/drm/i915/display/intel_dpt.c:136:21: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/display/intel_dpt.c:136:21: expected struct i915_vma *[assigned] vma
drivers/gpu/drm/i915/display/intel_dpt.c:136:21: got void [noderef] __iomem *[assigned] iomem
v2: The code moved into intel_dpt.c
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712161815.24776-1-ville.syrjala@linux.intel.com
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
drm_dp_dpcd_read/write already has debug error message.
Drop redundant error messages which gives false
status even if correct value is read in drm_dp_dpcd_read().
v2: -Added fixes tag (Ankit)
v3: -Fixed build error (CI)
Fixes: 9488a030ac ("drm/i915: Add support for enabling link status and recovery")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812131107.5531-1-swati2.sharma@intel.com
DP 2.0 UHBR link rates always use 128b/132b channel encoding, which has
a different data bandwidth efficiency from 8b/10b. The computation is
slightly convoluted due to the units we use; this is all explained in
the added comment.
v2: Clarified comment (Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8afd8d97a04c2d86c2dcadfed9f8e1f84272a13c.1629735412.git.jani.nikula@intel.com
