[ Upstream commit f4aec227e9 ]
SCSSI has reset controls for each channel in the SoCs newer than Pro4,
so this adds missing reset controls for channel 1, 2 and 3. And more, this
moves MCSSI reset ID after SCSSI.
Fixes: 6b39fd590a ("reset: uniphier: add reset control support for SPI")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02aeb2f215 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f25c7a006c ]
In case of tiled displays, if we hotplug just one connector,
fbcon currently just selects the preferred mode and if it is
tiled mode then that becomes a problem if rest of the tiles are
not present.
So in the fbdev driver on hotplug when we probe the client modeset,
if we dont find all the connectors for all tiles, then on a connector
with one tile, just fallback to the first available non tiled mode
to display over a single connector.
On the hotplug of the consecutive tiled connectors, if the tiled mode
no longer exists because of fbcon size limitation, then return
no modes for consecutive tiles but retain the non tiled mode
on the 0th tile.
Use the same logic in case of connected boot case as well.
This has been tested with Dell UP328K tiled monitor.
v2:
* Set the modes on consecutive hotplugged tiles to no mode
if tiled mode is pruned (Dave)
v1:
* Just handle the 1st connector hotplug case
* v1 Reviewed-by: Dave Airlie <airlied@redhat.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Dave Airlie <airlied@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113222952.9231-1-manasi.d.navare@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eff5d31f74 ]
To build test, add COMPILE_TEST depedency to both ARM_RK3399_DMC_DEVFREQ
and DEVFREQ_EVENT_ROCKCHIP_DFI configuration. And ARM_RK3399_DMC_DEVFREQ
used the SMCCC interface so that add HAVE_ARM_SMCCC dependency to prevent
the build break.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b76b3479da ]
Change time stats counting to bigger type by using 64-bit jiffies.
This will make devfreq stats code look similar to cpufreq stats and
prevents overflow (for HZ = 1000 after 49.7 days).
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4556f5e99 ]
Putting a 'struct devfreq_event_dev' object on the stack is generally
a bad idea and here it leads to a warnig about potential stack overflow:
drivers/devfreq/event/exynos-ppmu.c:643:12: error: stack frame size of 1040 bytes in function 'exynos_ppmu_probe' [-Werror,-Wframe-larger-than=]
There is no real need for the device structure, only the string inside
it, so add an internal helper function that simply takes the string
as its argument and remove the device structure.
Fixes: 1dd62c66d3 ("PM / devfreq: events: extend events by type of counted data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[cw00.choi: Fix the issue from 'desc->name' to 'desc[j].name']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bff47c2302 ]
When building with C=1, sparse issues a warning:
CHECK arch/x86/entry/vdso/vdso32-setup.c
arch/x86/entry/vdso/vdso32-setup.c:28:28: warning: symbol 'vdso32_enabled' was not declared. Should it be static?
Provide the missing header file.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/36224.1575599767@turing-police
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93e23eb2ed ]
Freed work request skbs when connection terminates.
enqueue_wr()/ dequeue_wr() is shared between softirq
and application contexts, should be protected by socket
lock. Moved dequeue_wr() to appropriate file.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aec743d69 ]
RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1162f84403 ]
Currently, when bpftool cgroup show <path> has an error, no error
message is printed. This is confusing because the user may think the
result is empty.
Before the change:
$ bpftool cgroup show /sys/fs/cgroup
ID AttachType AttachFlags Name
$ echo $?
255
After the change:
$ ./bpftool cgroup show /sys/fs/cgroup
Error: can't query bpf programs attached to /sys/fs/cgroup: Operation
not permitted
v2: Rename check_query_cgroup_progs to cgroup_has_attached_progs
Signed-off-by: Hechao Li <hechaol@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191224011742.3714301-1-hechaol@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02939cd167 ]
The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59ef4da4e4 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/clk/clk-bm1880.c: In function 'bm1880_pll_rate_calc':
drivers/clk/clk-bm1880.c:477:13: warning:
variable 'fref' set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.kernel.org/r/20191129033534.188257-1-yuehaibing@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dae7a589c1 ]
dma_chan_to_owner() dereferences the driver from the struct device to
obtain the owner and call module_[get|put](). However, if the backing
device is unbound before the dma_device is unregistered, the driver
will be cleared and this will cause a NULL pointer dereference.
Instead, store a pointer to the owner module in the dma_device struct
so the module reference can be properly put when the channel is put, even
if the backing device was destroyed first.
This change helps to support a safer unbind of DMA engines.
If the dma_device is unregistered in the driver's remove function,
there's no guarantee that there are no existing clients and a users
action may trigger the WARN_ONCE in dma_async_device_unregister()
which is unlikely to leave the system in a consistent state.
Instead, a better approach is to allow the backing driver to go away
and fail any subsequent requests to it.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6fa75ca91 ]
__clk_init_parent() will call the .get_parent() callback of the clock
so .init() must run before.
Fixes: 541debae0a ("clk: call the clock init() callback before any other ops callback")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lkml.kernel.org/r/20190924123954.31561-2-jbrunet@baylibre.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 966b753cf3 ]
Current implementation for IOMMU x2APIC support makes use of
the MMIO access to MSI capability block registers, which requires
checking EFR[MsiCapMmioSup]. However, only IVHD type 11h/40h contain
the information, and not in the IVHD type 10h IOMMU feature reporting
field. Since the BIOS in newer systems, which supports x2APIC, would
normally contain IVHD type 11h/40h, remove the IOMMU_FEAT_XTSUP_SHIFT
check for IVHD type 10h, and only support x2APIC with IVHD type 11h/40h.
Fixes: 6692981295 ('iommu/amd: Add support for X2APIC IOMMU interrupts')
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 813071438e ]
The IOMMU MMIO access to MSI capability registers is available only if
the EFR[MsiCapMmioSup] is set. Current implementation assumes this bit
is set if the EFR[XtSup] is set, which might not be the case.
Fix by checking the EFR[MsiCapMmioSup] before accessing the MSI address
low/high and MSI data registers via the MMIO.
Fixes: 6692981295 ('iommu/amd: Add support for X2APIC IOMMU interrupts')
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb950bca5d ]
Commit d355bb2097 ("PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()")
unexported a bunch of symbols from the PCI core since the only external
users were non-modular IOMMU drivers. Although most of those symbols
can remain private for now, 'pci_{enable,disable_ats()' is required for
the ARM SMMUv3 driver to build as a module, otherwise we get a build
failure as follows:
| ERROR: "pci_enable_ats" [drivers/iommu/arm-smmu-v3.ko] undefined!
| ERROR: "pci_disable_ats" [drivers/iommu/arm-smmu-v3.ko] undefined!
Re-export these two functions so that the ARM SMMUv3 driver can be build
as a module.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: John Garry <john.garry@huawei.com> # smmu v3
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e198c395a ]
The WiFi firmware used on db845c implements the 8bit host-capability
message, so enable the quirk for this.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191113232245.4039932-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df9166bfa7 ]
This patch reworks the fdmi symbolic node name data for the following two
issues:
- Correcting extraneous periods following the DV and HN fdmi data fields.
- Avoiding buffer overflow issues when formatting the data.
The fix to the fist issue is to just remove the characters.
The fix to the second issue has all data being staged in temporary storage
before being moved to the real buffer.
Link: https://lore.kernel.org/r/20191218235808.31922-3-jsmart2021@gmail.com
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 030b995ad9 ]
In AVC update we don't call avc_node_kill() when avc_xperms_populate()
fails, resulting in the avc->avc_cache.active_nodes counter having a
false value. In last patch this changes was missed , so correcting it.
Fixes: fa1aa143ac ("selinux: extended permissions for ioctls")
Signed-off-by: Jaihind Yadav <jaihindyadav@codeaurora.org>
Signed-off-by: Ravi Kumar Siddojigari <rsiddoji@codeaurora.org>
[PM: merge fuzz, minor description cleanup]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba519aa13 ]
Currently the mem clk is voted upon from both the active and proxy pool on
MSM8998 SoCs where only a proxy vote should suffice. Fix this by removing
mem clk from the active pool.
Fixes: 1665cbd573 ("remoteproc: qcom_q6v5_mss: Add support for MSM8998")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20191218132217.28141-2-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8443ffd1bb ]
Add a device node for the global timer, which is part of the Cortex-A9
MPCore.
The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d67c0340a ]
I was unable to get clk_set_rate() setting a lower RPC-IF clock frequency
and that issue boiled down to me not passing CLK_SET_RATE_PARENT flag to
clk_register_composite() when registering the RPC[D2] clocks...
Fixes: db4a0073cc ("clk: renesas: rcar-gen3: Add RPC clocks")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/be27a344-d8bf-9e0c-8950-2d1b48498496@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 411f5c1eac ]
The driver currently handles vblank events only when updating planes on
an already enabled CRTC. The atomic update API however allows requesting
an event when enabling or disabling a CRTC. This currently leads to
event objects being leaked in the kernel and to events not being sent
out. Fix it.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d07de2c18 ]
Currently CONFIG_CRYPTO_DEV_AMLOGIC_GXL=y implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/crypto/amlogic/amlogic-gxl-core.o: in function `meson_crypto_probe':
drivers/crypto/amlogic/amlogic-gxl-core.c:240: undefined reference to `devm_platform_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dc0e31062 ]
Currently CONFIG_CRYPTO_DEV_SAFEXCEL=y implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/crypto/inside-secure/safexcel.o: in function `safexcel_probe':
drivers/crypto/inside-secure/safexcel.c:1692: undefined reference to `devm_platform_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dbc96ad65 ]
Clang warns:
../drivers/scsi/aic7xxx/aic7xxx_core.c:2317:5: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
if ((syncrate->sxfr_u2 & ST_SXFR) != 0)
^
../drivers/scsi/aic7xxx/aic7xxx_core.c:2310:4: note: previous statement
is here
if (syncrate == &ahc_syncrates[maxsync])
^
1 warning generated.
This warning occurs because there is a space amongst the tabs on this
line. Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
This has been a problem since the beginning of git history hence no fixes
tag.
Link: https://github.com/ClangBuiltLinux/linux/issues/817
Link: https://lore.kernel.org/r/20191218014220.52746-1-natechancellor@gmail.com
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df74b6985 ]
In UFS host reset and restore path, before probe, we stop and start the
host controller once. After host controller is stopped, the pending
requests, if any, are cleared from the doorbell, but no completion IRQ
would be raised due to the hba is stopped. These pending requests shall be
completed along with the first NOP_OUT command (as it is the first command
which can raise a transfer completion IRQ) sent during probe. Since the
OCSs of these pending requests are not SUCCESS (because they are not yet
literally finished), their UPIUs shall be dumped. When there are multiple
pending requests, the UPIU dump can be overwhelming and may lead to
stability issues because it is in atomic context. Therefore, before probe,
complete these pending requests right after host controller is stopped and
silence the UPIU dump from them.
Link: https://lore.kernel.org/r/1574751214-8321-5-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f6403496 ]
vfs_clone_file_range() can modify the metadata on the source file too,
so we need to commit that to stable storage as well.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Acked-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ddbd77181 ]
ACPICA commit 29cc8dbc5463a93625bed87d7550a8bed8913bf4
create_buffer_field is a deferred op that is typically processed in
load pass 2. However, disassembly of control method contents walk the
parse tree with ACPI_PARSE_LOAD_PASS1 and AML_CREATE operators are
processed in a later walk. This is a problem when there is a control
method that has the same name as the AML_CREATE object. In this case,
any use of the name segment will be detected as a method call rather
than a reference to a buffer field. If this is detected as a method
call, it can result in a mal-formed parse tree if the control methods
have parameters.
This change in processing AML_CREATE ops earlier solves this issue by
inserting the named object in the ACPI namespace so that references
to this name would be detected as a name string rather than a method
call.
Link: 29cc8dbc
Reported-by: Elia Geretto <elia.f.geretto@gmail.com>
Tested-by: Elia Geretto <elia.f.geretto@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87ec9adcca ]
It turns out booting the modem is dependent on a bimc vote from Linux on
msm8998. To make the modem happy, add the bimc clock to rely on the
default vote from rpmcc. Once we have interconnect support, bimc should
be controlled properly.
Fixes: 6131dc8121 ("clk: qcom: smd: Add support for MSM8998 rpm clocks")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191217165409.4919-1-jeffrey.l.hugo@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7489a7e1 ]
issues:
MEC is ruined by the amdkfd_pre_reset after VF FLR done
fix:
amdkfd_pre_reset() would ruin MEC after hypervisor finished the VF FLR,
the correct sequence is do amdkfd_pre_reset before VF FLR but there is
a limitation to block this sequence:
if we do pre_reset() before VF FLR, it would go KIQ way to do register
access and stuck there, because KIQ probably won't work by that time
(e.g. you already made GFX hang)
so the best way right now is to simply remove it.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1512d064f5 ]
issues:
gpu_recover() is re-entered by the mailbox interrupt
handler mxgpu_nv.c
fix:
we need to bypass the gpu_recover() invoke in mailbox
interrupt as long as the timeout is not infinite (thus the TDR
will be triggered automatically after time out, no need to invoke
gpu_recover() through mailbox interrupt.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5479034576 ]
[Why]
A corner case currently exists where DPP DTO is lowered before
pipes are updated to a higher viewport. This causes underflow
as the DPPCLK is too low for the current viewport.
[How]
Only lower DPP DTO when it is safe to lower, or if
the newer clocks are higher than the current ones.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 615b9b585e ]
[Why]
Previously update_bw_bounding_box for RN was commented out
due to incorrect values causing BSOD on Hybrid Graphics.
However, commenting out this function also may cause issues
such as underflow in certain cases such as 2x4K displays.
[How]
Fix dram_speed_mts calculations.
Update from proper index of clock_limits[]
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c705f9fc6a ]
In ezusb_init, if upriv is NULL, the code crashes. However, the caller
in ezusb_probe can handle the error and print the failure message.
The patch replaces the BUG_ON call to error return.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b90dfc487 ]
The PLX PEX NTB forwards DMA transactions using Requester IDs that don't
exist as PCI devices. The devfn for a transaction is used as an index into
a lookup table storing the origin of a transaction on the other side of the
bridge.
Alias all possible devfns to the NTB device so that any transaction coming
in is governed by the mappings for the NTB.
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09298542cd ]
Add a "nr_devfns" parameter to pci_add_dma_alias() so it can be used to
create DMA aliases for a range of devfns.
[bhelgaas: incorporate nr_devfns fix from James, update
quirk_pex_vca_alias() and setup_aliases()]
Signed-off-by: James Sewart <jamessewart@arista.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 057f184b12 ]
Starting in v5.5, the timestamps are correctly passed down as
64-bit seconds with NFSv4 on 32-bit machines, but some debug
statements still truncate them to 'long'.
Fixes: e86d5a0287 ("NFS: Convert struct nfs_fattr to use struct timespec64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df4654bd6e ]
Clang warns:
../sound/usb/usx2y/usX2Yhwdep.c:122:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
info->version = USX2Y_DRIVER_VERSION;
^
../sound/usb/usx2y/usX2Yhwdep.c:120:2: note: previous statement is here
if (us428->chip_status & USX2Y_STAT_CHIP_INIT)
^
1 warning generated.
This warning occurs because there is a space before the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
This was introduced before the beginning of git history so no fixes tag.
Link: https://github.com/ClangBuiltLinux/linux/issues/831
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20191218034257.54535-1-natechancellor@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0705f95c33 ]
ERSPAN_VERSION is an attribute parsed in kernel side, nla_policy
type should be added for it, like other attributes.
Fixes: af308b94a2 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db1ae0314f ]
throttle_active_work() is only called if CONFIG_SYSFS is set, otherwise
we get a harmless warning:
arch/x86/kernel/cpu/mce/therm_throt.c:238:13: error: 'throttle_active_work' \
defined but not used [-Werror=unused-function]
Mark the function as __maybe_unused to avoid the warning.
Fixes: f6656208f0 ("x86/mce/therm_throt: Optimize notifications of thermal throttle")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: bberg@redhat.com
Cc: ckellner@redhat.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: hdegoede@redhat.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191210203925.3119091-1-arnd@arndb.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbd20c939c ]
In fore200e_send and fore200e_close, the pointers from the arguments
are dereferenced in the variable declaration block and then checked
for NULL. The patch fixes these issues by avoiding NULL pointer
dereferences.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
