- Collect interrupt-related code in irq.c (Ilpo Järvinen)
- Mark 3ware-9650SE Root Port Extended Tags as broken (Jörg Wedekind)
* pci/enumeration:
PCI: Mark 3ware-9650SE Root Port Extended Tags as broken
PCI: Place interrupt related code into irq.c
# Conflicts:
# drivers/pci/Makefile
- After a DPC event, print all logged TLP Prefixes instead of printing the
first prefix several times (Ilpo Järvinen)
- Ignore the expected Surprise Down error that may cause a DPC event when
hot-removing a device (Smita Koralahalli)
- Add an RP PIO log size quirk for Intel Raptor Lake Root Ports, which
still don't advertise the correct log size, which prevented logging of RP
PIO Log registers when DPC is triggered (Paul Menzel)
* pci/dpc:
PCI/DPC: Quirk PIO log size for Intel Raptor Lake Root Ports
PCI/DPC: Ignore Surprise Down error on hot removal
PCI/DPC: Print all TLP Prefixes, not just the first
- Unmap MMIO mappings in pci_iounmap() to avoid a leak when
ARCH_HAS_GENERIC_IOPORT_MAP is defined (Philipp Stanner)
- Move pci_iomap.c to drivers/pci/ since it's all PCI-related (Philipp
Stanner)
- Move other PCI-related devres code from lib/devres.c to drivers/pci/
(Philipp Stanner)
- Move other devres code from pci.c to devres.c (Philipp Stanner)
* pci/devres:
PCI: Move devres code from pci.c to devres.c
PCI: Move PCI-specific devres code to drivers/pci/
PCI: Move pci_iomap.c to drivers/pci/
pci_iounmap(): Fix MMIO mapping leak
- Collect ASPM-related code into aspm.c (David E. Box)
- Save and restore ASPM L1 PM Substates configuration so these states
continue working after suspend/resume (David E. Box)
- Move the ASPM L1.2-related LTR save/restore next to the ASPM save/restore
(David E. Box)
- Move the required L1 disable before L1 Substate configuration into
pci_restore_aspm_l1ss_state() (Bjorn Helgaas)
- Update save_save when ASPM config is changed, so a .slot_reset() during
error recovery restores the changed config, not the .probe()-time config
(Vidya Sagar)
* pci/aspm:
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
PCI/ASPM: Move pci_configure_ltr() to aspm.c
- Fix sysfs paths in aer_rootport_total_err_* documentation (Johan Hovold)
- Block runtime suspend while handling AER errors (Stanislaw Gruszka)
- Add a generic Header Log structure and reader shared by AER and DPC (Ilpo
Järvinen)
* pci/aer:
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI/AER: Block runtime suspend when handling errors
PCI/AER: Clean up version indentation in ABI docs
PCI/AER: Fix rootport attribute paths in ABI docs
This patch fixes to check on the right return value if it was the last
callback. The rv variable got overwritten by the return of
copy_result_to_user(). Fixing it by introducing a second variable for
the return value and don't let rv being overwritten.
Cc: stable@vger.kernel.org
Fixes: 61bed0baa4 ("fs: dlm: use a non-static queue for callbacks")
Reported-by: Valentin Vidić <vvidic@valentin-vidic.from.hr>
Closes: https://lore.kernel.org/gfs2/Ze4qSvzGJDt5yxC3@valentin-vidic.from.hr
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Many PCIe device drivers save the configuration state of their device
during probe and restore it when their .slot_reset() hook is called during
PCIe error recovery.
If the ASPM configuration is changed after the driver's probe is called and
before an error event occurs, .slot_reset() restores the ASPM configuration
to what it was at the time of probe, not to what it was just before the
occurrence of the error event. This leads to a mismatch in ASPM
configuration between the device and its upstream device.
Update the saved configuration of the device when the ASPM configuration
changes.
Link: https://lore.kernel.org/r/20240222174436.3565146-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[bhelgaas: commit log, rebase to pci/aspm, rename to
pci_update_aspm_saved_state() since it updates only LNKCTL, update only
ASPMC and CLKREQ_EN in LNKCTL]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Per PCIe r6.1, sec 5.5.4, L1 must be disabled while setting ASPM L1 PM
Substates enable bits. Previously this was enforced by clearing
PCI_EXP_LNKCTL_ASPMC before calling pci_restore_aspm_l1ss_state().
Move the L1 (and L0s, although that doesn't seem required) disable into
pci_restore_aspm_l1ss_state() itself so it's closer to the code that
depends on it.
Link: https://lore.kernel.org/r/20240223213733.GA115410@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Continuing work by Ard Biesheuvel to improve the x86 early startup code,
with the long-term goal to make it position independent:
- Get rid of early accesses to global objects, either by moving them
to the stack, deferring the access until later, or dropping the
globals entirely.
- Move all code that runs early via the 1:1 mapping into .head.text,
and move code that does not out of it, so that build time checks can
be added later to ensure that no inadvertent absolute references were
emitted into code that does not tolerate them.
- Remove fixup_pointer() and occurrences of __pa_symbol(), which rely
on the compiler emitting absolute references, which is not guaranteed.
- Improve the early console code.
- Add early console message about ignored NMIs, so that users are at least
warned about their existence - even if we cannot do anything about them.
- Improve the kexec code's kernel load address handling.
- Enable more X86S (simplified x86) bits.
- Simplify early boot GDT handling
- Micro-optimize the boot code a bit
- Misc cleanups.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zvw3
-----END PGP SIGNATURE-----
Merge tag 'x86-boot-2024-03-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 boot updates from Ingo Molnar:
- Continuing work by Ard Biesheuvel to improve the x86 early startup
code, with the long-term goal to make it position independent:
- Get rid of early accesses to global objects, either by moving
them to the stack, deferring the access until later, or dropping
the globals entirely
- Move all code that runs early via the 1:1 mapping into
.head.text, and move code that does not out of it, so that build
time checks can be added later to ensure that no inadvertent
absolute references were emitted into code that does not
tolerate them
- Remove fixup_pointer() and occurrences of __pa_symbol(), which
rely on the compiler emitting absolute references, which is not
guaranteed
- Improve the early console code
- Add early console message about ignored NMIs, so that users are at
least warned about their existence - even if we cannot do anything
about them
- Improve the kexec code's kernel load address handling
- Enable more X86S (simplified x86) bits
- Simplify early boot GDT handling
- Micro-optimize the boot code a bit
- Misc cleanups
* tag 'x86-boot-2024-03-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/sev: Move early startup code into .head.text section
x86/sme: Move early SME kernel encryption handling into .head.text
x86/boot: Move mem_encrypt= parsing to the decompressor
efi/libstub: Add generic support for parsing mem_encrypt=
x86/startup_64: Simplify virtual switch on primary boot
x86/startup_64: Simplify calculation of initial page table address
x86/startup_64: Defer assignment of 5-level paging global variables
x86/startup_64: Simplify CR4 handling in startup code
x86/boot: Use 32-bit XOR to clear registers
efi/x86: Set the PE/COFF header's NX compat flag unconditionally
x86/boot/64: Load the final kernel GDT during early boot directly, remove startup_gdt[]
x86/boot/64: Use RIP_REL_REF() to access early_top_pgt[]
x86/boot/64: Use RIP_REL_REF() to access early page tables
x86/boot/64: Use RIP_REL_REF() to access '__supported_pte_mask'
x86/boot/64: Use RIP_REL_REF() to access early_dynamic_pgts[]
x86/boot/64: Use RIP_REL_REF() to assign 'phys_base'
x86/boot/64: Simplify global variable accesses in GDT/IDT programming
x86/trampoline: Bypass compat mode in trampoline_start64() if not needed
kexec: Allocate kernel above bzImage's pref_address
x86/boot: Add a message about ignored early NMIs
...
4ff116d0d5 ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume") restored the L1 PM Substates Capability after resume,
which reduced power consumption by making the ASPM L1.x states work after
resume.
a7152be79b ("Revert "PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume"") reverted 4ff116d0d5 because resume failed on some
systems, so power consumption after resume increased again.
a7152be79b mentioned that we restore L1 PM substate configuration even
though ASPM L1 may already be enabled. This is due the fact that the
pci_restore_aspm_l1ss_state() was called before pci_restore_pcie_state().
Save and restore the L1 PM Substates Capability, following PCIe r6.1, sec
5.5.4 more closely by:
1) Do not restore ASPM configuration in pci_restore_pcie_state() but
do that after PCIe capability is restored in pci_restore_aspm_state()
following PCIe r6.1, sec 5.5.4.
2) If BIOS reenables L1SS, particularly L1.2, we need to clear the
enables in the right order, downstream before upstream. Defer
restoring the L1SS config until we are at the downstream component.
Then update the config for both ends of the link in the prescribed
order.
3) Program ASPM L1 PM substate configuration before L1 enables.
4) Program ASPM L1 PM substate enables last, after rest of the fields
in the capability are programmed.
[bhelgaas: commit log, squash L1SS-related patches, do both LNKCTL restores
in pci_restore_pcie_state()]
Link: https://lore.kernel.org/r/20240128233212.1139663-3-david.e.box@linux.intel.com
Link: https://lore.kernel.org/r/20240128233212.1139663-4-david.e.box@linux.intel.com
Link: https://lore.kernel.org/r/20240223205851.114931-5-helgaas@kernel.org
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217321
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216782
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216877
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Co-developed-by: David E. Box <david.e.box@linux.intel.com>
Reported-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Tasev Nikola <tasev.stefanoska@skynet.be> # Asus UX305FA
Cc: Mark Enriquez <enriquezmark36@gmail.com>
Cc: Thomas Witt <kernel@witt.link>
Cc: Werner Sembach <wse@tuxedocomputers.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
-----BEGIN PGP SIGNATURE-----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=Sq5d
-----END PGP SIGNATURE-----
Merge tag 'x86-apic-2024-03-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 APIC fixup from Dave Hansen:
"Revert VERW fixed addressing patch.
The reverted commit is not x86/apic material and was cruft left over
from a merge.
I believe the sequence of events went something like this:
- The commit in question was added to x86/urgent
- x86/urgent was merged into x86/apic to resolve a conflict
- The commit was zapped from x86/urgent, but *not* from x86/apic
- x86/apic got pullled (yesterday)
I think we need to be a bit more vigilant when zapping things to make
sure none of the other branches are depending on the zapped material"
* tag 'x86-apic-2024-03-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/bugs: Use fixed addressing for VERW operand"
When the trace_pipe_raw file is closed, there should be no new readers on
the file descriptor. This is mostly handled with the waking and wait_index
fields of the iterator. But there's still a slight race.
CPU 0 CPU 1
----- -----
wait_index++;
index = wait_index;
ring_buffer_wake_waiters();
wait_on_pipe()
ring_buffer_wait();
The ring_buffer_wait() will miss the wakeup from CPU 1. The problem is
that the ring_buffer_wait() needs the logic of:
prepare_to_wait();
if (!condition)
schedule();
Where the missing condition check is the iter->wait_index update.
Have the ring_buffer_wait() take a conditional callback function and a
data parameter that can be used within the wait_event_interruptible() of
the ring_buffer_wait() function.
In wait_on_pipe(), pass a condition function that will check if the
wait_index has been updated, if it has, it will return true to break out
of the wait_event_interruptible() loop.
Create a new field "closed" in the trace_iterator and set it in the
.flush() callback before calling ring_buffer_wake_waiters().
This will keep any new readers from waiting on a closed file descriptor.
Have the wait_on_pipe() condition callback also check the closed field.
Change the wait_index field of the trace_iterator to atomic_t. There's no
reason it needs to be 'long' and making it atomic and using
atomic_read_acquire() and atomic_fetch_inc_release() will provide the
necessary memory barriers.
Add a "woken" flag to tracing_buffers_splice_read() to exit the loop after
one more try to fetch data. That is, if it waited for data and something
woke it up, it should try to collect any new data and then exit back to
user space.
Link: https://lore.kernel.org/linux-trace-kernel/CAHk-=wgsNgewHFxZAJiAQznwPMqEtQmi1waeS2O1v6L4c_Um5A@mail.gmail.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240312121703.557950713@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: f3ddb74ad0 ("tracing: Wake up ring buffer waiters on closing of the file")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Convert ring_buffer_wait() over to wait_event_interruptible(). The default
condition is to execute the wait loop inside __wait_event() just once.
This does not change the ring_buffer_wait() prototype yet, but
restructures the code so that it can take a "cond" and "data" parameter
and will call wait_event_interruptible() with a helper function as the
condition.
The helper function (rb_wait_cond) takes the cond function and data
parameters. It will first check if the buffer hit the watermark defined by
the "full" parameter and then call the passed in condition parameter. If
either are true, it returns true.
If rb_wait_cond() does not return true, it will set the appropriate
"waiters_pending" flag and returns false.
Link: https://lore.kernel.org/linux-trace-kernel/CAHk-=wgsNgewHFxZAJiAQznwPMqEtQmi1waeS2O1v6L4c_Um5A@mail.gmail.com/
Link: https://lore.kernel.org/linux-trace-kernel/20240312121703.399598519@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: f3ddb74ad0 ("tracing: Wake up ring buffer waiters on closing of the file")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The check for knowing if the poll should wait or not is basically the
exact same logic as rb_watermark_hit(). The only difference is that
rb_watermark_hit() also handles the !full case. But for the full case, the
logic is the same. Just call that instead of duplicating the code in
ring_buffer_poll_wait().
Link: https://lore.kernel.org/linux-trace-kernel/20240312131952.802267543@goodmis.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
If a reader of the ring buffer is doing a poll, and waiting for the ring
buffer to hit a specific watermark, there could be a case where it gets
into an infinite ping-pong loop.
The poll code has:
rbwork->full_waiters_pending = true;
if (!cpu_buffer->shortest_full ||
cpu_buffer->shortest_full > full)
cpu_buffer->shortest_full = full;
The writer will see full_waiters_pending and check if the ring buffer is
filled over the percentage of the shortest_full value. If it is, it calls
an irq_work to wake up all the waiters.
But the code could get into a circular loop:
CPU 0 CPU 1
----- -----
[ Poll ]
[ shortest_full = 0 ]
rbwork->full_waiters_pending = true;
if (rbwork->full_waiters_pending &&
[ buffer percent ] > shortest_full) {
rbwork->wakeup_full = true;
[ queue_irqwork ]
cpu_buffer->shortest_full = full;
[ IRQ work ]
if (rbwork->wakeup_full) {
cpu_buffer->shortest_full = 0;
wakeup poll waiters;
[woken]
if ([ buffer percent ] > full)
break;
rbwork->full_waiters_pending = true;
if (rbwork->full_waiters_pending &&
[ buffer percent ] > shortest_full) {
rbwork->wakeup_full = true;
[ queue_irqwork ]
cpu_buffer->shortest_full = full;
[ IRQ work ]
if (rbwork->wakeup_full) {
cpu_buffer->shortest_full = 0;
wakeup poll waiters;
[woken]
[ Wash, rinse, repeat! ]
In the poll, the shortest_full needs to be set before the
full_pending_waiters, as once that is set, the writer will compare the
current shortest_full (which is incorrect) to decide to call the irq_work,
which will reset the shortest_full (expecting the readers to update it).
Also move the setting of full_waiters_pending after the check if the ring
buffer has the required percentage filled. There's no reason to tell the
writer to wake up waiters if there are no waiters.
Link: https://lore.kernel.org/linux-trace-kernel/20240312131952.630922155@goodmis.org
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
The rb_watermark_hit() checks if the amount of data in the ring buffer is
above the percentage level passed in by the "full" variable. If it is, it
returns true.
But it also sets the "shortest_full" field of the cpu_buffer that informs
writers that it needs to call the irq_work if the amount of data on the
ring buffer is above the requested amount.
The rb_watermark_hit() always sets the shortest_full even if the amount in
the ring buffer is what it wants. As it is not going to wait, because it
has what it wants, there's no reason to set shortest_full.
Link: https://lore.kernel.org/linux-trace-kernel/20240312115641.6aa8ba08@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Fixes: 42fb0a1e84 ("tracing/ring-buffer: Have polling block on watermark")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
When pcm_runtime is adding platform components it will scan all
registered components. In case of DPCM FE/BE some DAI links will
configure dummy platform. However both dummy codec and dummy platform
are using "snd-soc-dummy" as component->name. Dummy codec should be
skipped when adding platforms otherwise there'll be overflow and UBSAN
complains.
Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Link: https://msgid.link/r/20240305065606.3778642-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5V9t
-----END PGP SIGNATURE-----
Merge tag 'rfds-for-linus-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RFDS mitigation from Dave Hansen:
"RFDS is a CPU vulnerability that may allow a malicious userspace to
infer stale register values from kernel space. Kernel registers can
have all kinds of secrets in them so the mitigation is basically to
wait until the kernel is about to return to userspace and has user
values in the registers. At that point there is little chance of
kernel secrets ending up in the registers and the microarchitectural
state can be cleared.
This leverages some recent robustness fixes for the existing MDS
vulnerability. Both MDS and RFDS use the VERW instruction for
mitigation"
* tag 'rfds-for-linus-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
x86/rfds: Mitigate Register File Data Sampling (RFDS)
Documentation/hw-vuln: Add documentation for RFDS
x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
The sample rates set by the rockchip_i2s_tdm driver in master mode are
inaccurate up to 5% in several cases, due to the driver logic to configure
clocks and a nasty interaction with the Common Clock Framework.
To understand what happens, here is the relevant section of the clock tree
(slightly simplified), along with the names used in the driver:
vpll0 _OR_ vpll1 "mclk_root"
clk_i2s2_8ch_tx_src "mclk_parent"
clk_i2s2_8ch_tx_mux
clk_i2s2_8ch_tx "mclk" or "mclk_tx"
This is what happens when playing back e.g. at 192 kHz using
audio-graph-card (when recording the same applies, only s/tx/rx/):
0. at probe, rockchip_i2s_tdm_set_sysclk() stores the passed frequency in
i2s_tdm->mclk_tx_freq (*) which is 50176000, and that is never modified
afterwards
1. when playback is started, rockchip_i2s_tdm_hw_params() is called and
does the following two calls
2. rockchip_i2s_tdm_calibrate_mclk():
2a. selects mclk_root0 (vpll0) as a parent for mclk_parent
(mclk_tx_src), which is OK because the vpll0 rate is a good for
192000 (and sumbultiple) rates
2b. sets the mclk_root frequency based on ppm calibration computations
2c. sets mclk_tx_src to 49152000 (= 256 * 192000), which is also OK as
it is a multiple of the required bit clock
3. rockchip_i2s_tdm_set_mclk()
3a. calls clk_set_rate() to set the rate of mclk_tx (clk_i2s2_8ch_tx)
to the value of i2s_tdm->mclk_tx_freq (*), i.e. 50176000 which is
not a multiple of the sampling frequency -- this is not OK
3a1. clk_set_rate() reacts by reparenting clk_i2s2_8ch_tx_src to
vpll1 -- this is not OK because the default vpll1 rate can be
divided to get 44.1 kHz and related rates, not 192 kHz
The result is that the driver does a lot of ad-hoc decisions about clocks
and ends up in using the wrong parent at an unoptimal rate.
Step 0 is one part of the problem: unless the card driver calls set_sysclk
at each stream start, whatever rate is set in mclk_tx_freq during boot will
be taken and used until reboot. Moreover the driver does not care if its
value is not a multiple of any audio frequency.
Another part of the problem is that the whole reparenting and clock rate
setting logic is conflicting with the CCF algorithms to achieve largely the
same goal: selecting the best parent and setting the closest clock
rate. And it turns out that only calling once clk_set_rate() on
clk_i2s2_8ch_tx picks the correct vpll and sets the correct rate.
The fix is based on removing the custom logic in the driver to select the
parent and set the various clocks, and just let the Clock Framework do it
all. As a side effect, the set_sysclk() op becomes useless because we now
let the CCF compute the appropriate value for the sampling rate. It also
implies that the whole calibration logic is now dead code and so it is
removed along with the "PCM Clock Compensation in PPM" kcontrol, which has
always been broken anyway. The handling of the 4 optional clocks also
becomes dead code and is removed.
The actual rates have been tested playing 30 seconds of audio at various
sampling rates before and after this change using sox:
time play -r <sample_rate> -n synth 30 sine 950 gain -3
The time reported in the table below is the 'real' value reported by the
'time' command in the above command line.
rate before after
--------- ------ ------
8000 Hz 30.60s 30.63s
11025 Hz 30.45s 30.51s
16000 Hz 30.47s 30.50s
22050 Hz 30.78s 30.41s
32000 Hz 31.02s 30.43s
44100 Hz 30.78s 30.41s
48000 Hz 29.81s 30.45s
88200 Hz 30.78s 30.41s
96000 Hz 29.79s 30.42s
176400 Hz 27.40s 30.41s
192000 Hz 29.79s 30.42s
While the tests are running the clock tree confirms that:
* without the patch, vpll1 is always used and clk_i2s2_8ch_tx always
produces 50176000 Hz, which cannot be divided for most audio rates
except the slowest ones, generating inaccurate rates
* with the patch:
- for 192000 Hz vpll0 is used
- for 176400 Hz vpll1 is used
- clk_i2s2_8ch_tx always produces (256 * <rate>) Hz
Tested on the RK3308 using the internal audio codec.
Fixes: 081068fd64 ("ASoC: rockchip: add support for i2s-tdm controller")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://msgid.link/r/20240305-rk3308-audio-codec-v4-1-312acdbe628f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we force enable power save on non-running vdevs, this results
in unexpected ping latency in below scenarios:
1. disable power save from userspace.
2. trigger suspend/resume.
With step 1 power save is disabled successfully and we get a good latency:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=5.13 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=5.45 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=5.99 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=6.34 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=4.47 ms
64 bytes from 192.168.1.1: icmp_seq=6 ttl=64 time=6.45 ms
While after step 2, the latency becomes much larger:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=17.7 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=15.0 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=14.3 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=16.5 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=20.1 ms
The reason is, with step 2, power save is force enabled due to vdev not
running, although mac80211 was trying to disable it to honor userspace
configuration:
ath11k_pci 0000:03:00.0: wmi cmd sta powersave mode psmode 1 vdev id 0
Call Trace:
ath11k_wmi_pdev_set_ps_mode
ath11k_mac_op_bss_info_changed
ieee80211_bss_info_change_notify
ieee80211_reconfig
ieee80211_resume
wiphy_resume
This logic is taken from ath10k where it was added due to below comment:
Firmware doesn't behave nicely and consumes more power than
necessary if PS is disabled on a non-started vdev.
However we don't know whether such an issue also occurs to ath11k firmware
or not. But even if it does, it's not appropriate because it goes against
userspace, even cfg/mac80211 don't know we have enabled it in fact.
Remove it to fix this issue. In this way we not only get a better latency,
but also, and the most important, keeps the consistency between userspace
and kernel/driver. The biggest price for that would be the power consumption,
which is not that important, compared with the consistency.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Fixes: b2beffa7d9 ("ath11k: enable 802.11 power save mode in station mode")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240309113115.11498-1-quic_bqiang@quicinc.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This was reverts commit 8009479ee9.
It was originally in x86/urgent, but was deemed wrong so got zapped.
But in the meantime, x86/urgent had been merged into x86/apic to
resolve a conflict. I didn't notice the merge so didn't zap it
from x86/apic and it managed to make it up with the x86/apic
material.
The reverted commit is known to cause some KASAN problems.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
CONFIG_SSB_DEBUG is used in one header file and nowhere else, so
remove it and the now-empty inline function that contained it. Also
remove the call to the empty inline function. The empty "default:"
case is kept to prevent 2 compiler warnings:
drivers/ssb/main.c:1133:9: warning: enumeration value 'SSB_BUSTYPE_PCMCIA' not handled in switch [-Wswitch]
drivers/ssb/main.c:1133:9: warning: enumeration value 'SSB_BUSTYPE_SDIO' not handled in switch [-Wswitch]
Reported-by: Ying Sun <sunying@isrc.iscas.ac.cn>
Link: https://lore.kernel.org/lkml/4e8525fe.607e2.18a8ddfdce8.Coremail.sunying@isrc.iscas.ac.cn/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Michael Büsch <m@bues.ch>
Cc: linux-wireless@vger.kernel.org
Cc: Kalle Valo <kvalo@kernel.org>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240309224540.22682-1-rdunlap@infradead.org
CYW43439 is a Wi-Fi + Bluetooth combo device from Infineon. The
WiFi part is capable of 802.11 b/g/n. This chip is present e.g.
on muRata 1YN module. Extend the binding with its DT compatible.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240309031355.269835-1-marex@denx.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/a92e4b2f7aace64a1e3a91af7974a6982700a18f.1709886922.git.u.kleine-koenig@pengutronix.de
The kzalloc() in brcmf_pcie_download_fw_nvram() will return null
if the physical memory has run out. As a result, if we use
get_random_bytes() to generate random bytes in the randbuf, the
null pointer dereference bug will happen.
In order to prevent allocation failure, this patch adds a separate
function using buffer on kernel stack to generate random bytes in
the randbuf, which could prevent the kernel stack from overflow.
Fixes: 91918ce88d ("wifi: brcmfmac: pcie: Provide a buffer of random bytes to the device")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240306140437.18177-1-duoming@zju.edu.cn
The ssb_device_uevent() function first attempts to convert the 'dev' pointer
to 'struct ssb_device *'. However, it mistakenly dereferences 'dev' before
performing the NULL check, potentially leading to a NULL pointer
dereference if 'dev' is NULL.
To fix this issue, move the NULL check before dereferencing the 'dev' pointer,
ensuring that the pointer is valid before attempting to use it.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Rand Deeb <rand.sec96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240306123028.164155-1-rand.sec96@gmail.com
We used EHT capability of 20MHz-only as rate mask to RA (rate adaptive)
H2C command when connecting with AP set EHT 20MHz. It would get the
wrong rate mask and the MCS rate can only reach MCS11.
According to the description of 802.11be spec, if all supported channel
bandwidth field of HE PHY capabilities are zero, then the EHT capability
of 20MHz-only is valid. As a result, we adjust the code to set correct
rate mask based on HE PHY bandwidth capability.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240305004502.6655-1-pkshih@realtek.com
The split of /reserved-memory handling between fdt.c and
of_reserved_mem.c makes for reading and restructuring the code
difficult. As of_reserved_mem.c is only built for
CONFIG_OF_EARLY_FLATTREE already, move all the code to one spot.
Acked-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Oreoluwa Babatunde <quic_obabatun@quicinc.com>
Link: https://lore.kernel.org/r/20240311181303.1516514-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
We make a few cancellation judgements based on ctx->rings, so let's
zero it afer deallocation for IORING_SETUP_NO_MMAP just like it's
done with the mmap case. Likely, it's not a real problem, but zeroing
is safer and better tested.
Cc: stable@vger.kernel.org
Fixes: 03d89a2de2 ("io_uring: support for user allocated memory for rings/sqes")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/9ff6cdf91429b8a51699c210e1f6af6ea3f8bdcf.1710255382.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If read multishot is being invoked from the poll retry handler, then we
should return IOU_ISSUE_SKIP_COMPLETE rather than -EAGAIN. If not, then
a CQE will be posted with -EAGAIN rather than triggering the retry when
the file is flagged as readable again.
Cc: stable@vger.kernel.org
Reported-by: Sargun Dhillon <sargun@meta.com>
Fixes: fc68fcda04 ("io_uring/rw: add support for IORING_OP_READ_MULTISHOT")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Yu Chien Peter Lin <peterlin@andestech.com> says:
This patch series introduces the Andes PMU extension, which serves the
same purpose as Sscofpmf and Smcntrpmf. Its non-standard local interrupt
is assigned to bit 18 in the custom S-mode local interrupt enable and
pending registers (slie/slip), while the interrupt cause is (256 + 18).
* b4-shazam-merge:
riscv: andes: Support specifying symbolic firmware and hardware raw events
riscv: dts: renesas: Add Andes PMU extension for r9a07g043f
dt-bindings: riscv: Add Andes PMU extension description
perf: RISC-V: Introduce Andes PMU to support perf event sampling
perf: RISC-V: Eliminate redundant interrupt enable/disable operations
riscv: dts: renesas: r9a07g043f: Update compatible string to use Andes INTC
dt-bindings: riscv: Add Andes interrupt controller compatible string
riscv: errata: Rename defines for Andes
Link: https://lore.kernel.org/r/20240222083946.3977135-1-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add the Andes AX45 JSON files that allows specifying symbolic event
names for the raw PMU events.
Signed-off-by: Locus Wei-Han Chen <locus84@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Charles Ci-Jyun Wu <dminus@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Acked-by: Ian Rogers <irogers@google.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-11-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
xandespmu stands for Andes Performance Monitor Unit extension.
Based on the added Andes PMU ISA string, the SBI PMU driver
will make use of the non-standard irq source.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240222083946.3977135-10-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Document the ISA string for Andes Technology performance monitor
extension which provides counter overflow interrupt and mode
filtering mechanisms.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-9-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Assign riscv_pmu_irq_num the value of (256 + 18) for the custome PMU
and add SSCOUNTOVF and SIP alternatives to ALT_SBI_PMU_OVERFLOW()
and ALT_SBI_PMU_OVF_CLEAR_PENDING() macros, respectively.
To make use of Andes PMU extension, "xandespmu" needs to be appended
to the riscv,isa-extensions for each cpu node in device-tree, and
make sure CONFIG_ANDES_CUSTOM_PMU is enabled.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Charles Ci-Jyun Wu <dminus@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Co-developed-by: Locus Wei-Han Chen <locus84@andestech.com>
Signed-off-by: Locus Wei-Han Chen <locus84@andestech.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-8-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The interrupt enable/disable operations are already performed by the
IRQ chip functions riscv_intc_irq_unmask()/riscv_intc_irq_mask() during
enable_percpu_irq()/disable_percpu_irq(). It can be done only once.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-7-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add "andestech,cpu-intc" compatible string to indicate that
Andes specific local interrupt is supported on the core,
e.g. AX45MP cores have 3 types of non-standard local interrupt
which can be handled in supervisor mode:
- Slave port ECC error interrupt
- Bus write transaction error interrupt
- Performance monitor overflow interrupt
These interrupts are enabled/disabled via a custom register
SLIE instead of the standard interrupt enable register SIE.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-5-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Use "ANDES" rather than "ANDESTECH" to unify the naming
convention with directory, file names, Kconfig options
and other definitions.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Charles Ci-Jyun Wu <dminus@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240222083946.3977135-2-peterlin@andestech.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
SPI controller with integrated chip select handling still need to adhere
to SPI device's CS setup, hold and inactive delays. For controller
without set_cs_timing spi core shall handle the delays to avoid
duplicated delay handling in each controller driver.
Fixes a regression for the out of tree SPI controller and SPI HID
transport on Apple M1/M1 Pro/Max notebooks.
Fixes: 4d8ff6b099 ("spi: Add multi-cs memories support in SPI core")
Signed-off-by: Janne Grunau <j@jannau.net>
Link: https://msgid.link/r/20240311-spi-cs-delays-regression-v1-1-0075020a90b2@jannau.net
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_lpspi_probe() is allocating/disposing memory manually with
spi_alloc_host()/spi_alloc_target(), but uses
devm_spi_register_controller(). In case of error after the latter call the
memory will be explicitly freed in the probe function by
spi_controller_put() call, but used afterwards by "devm" management outside
probe() (spi_unregister_controller() <- devm_spi_unregister() below).
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070
...
Call trace:
kernfs_find_ns
kernfs_find_and_get_ns
sysfs_remove_group
sysfs_remove_groups
device_remove_attrs
device_del
spi_unregister_controller
devm_spi_unregister
release_nodes
devres_release_all
really_probe
driver_probe_device
__device_attach_driver
bus_for_each_drv
__device_attach
device_initial_probe
bus_probe_device
deferred_probe_work_func
process_one_work
worker_thread
kthread
ret_from_fork
Fixes: 5314987de5 ("spi: imx: add lpspi bus driver")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://msgid.link/r/20240312112050.2503643-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, performing an exclusive get on an already-enabled regulator
resulted in inconsistent state initialization between child and parent
regulators. While the child's counts were updated, its parent's counters
remained unaffected.
Consequently, attempting to disable an already-enabled exclusive regulator
triggered unbalanced disables warnings from its parent regulator.
This commit addresses the issue by propagating the enable state to the
parent regulator using a regulator_enable call. This ensures consistent
state management across the regulator hierarchy, preventing warnings!
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://msgid.link/r/20240312091638.1266167-1-kory.maincent@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'gpio-ranges' is a phandle-array which is really a matrix. The schema in
cirrus,cs42l43 is incomplete as it doesn't define there's only a single
entry. Add the outer array constraints that there is a single entry.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://msgid.link/r/20240311222554.1940567-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
