[ Upstream commit 285994a62c ]
The ARM architecture allows the caching of intermediate page table
levels and page table freeing requires a sequence like:
pmd_clear()
TLB invalidation
pte page freeing
With commit 5e5f6dc105 (arm64: mm: enable HAVE_RCU_TABLE_FREE logic),
the page table freeing batching was moved from tlb_remove_page() to
tlb_remove_table(). The former takes care of TLB invalidation as this is
also shared with pte clearing and page cache page freeing. The latter,
however, does not invalidate the TLBs for intermediate page table levels
as it probably relies on the architecture code to do it if required.
When the mm->mm_users < 2, tlb_remove_table() does not do any batching
and page table pages are freed before tlb_finish_mmu() which performs
the actual TLB invalidation.
This patch introduces __tlb_flush_pgtable() for arm64 and calls it from
the {pte,pmd,pud}_free_tlb() directly without relying on deferred page
table freeing.
Fixes: 5e5f6dc105 arm64: mm: enable HAVE_RCU_TABLE_FREE logic
Reported-by: Jon Masters <jcm@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit fb7332a9fe ]
On architectures with hardware broadcasting of TLB invalidation messages
, it makes sense to reduce the range of the mmu_gather structure when
unmapping page ranges based on the dirty address information passed to
tlb_remove_tlb_entry.
arm64 already does this by directly manipulating the start/end fields
of the gather structure, but this confuses the generic code which
does not expect these fields to change and can end up calculating
invalid, negative ranges when forcing a flush in zap_pte_range.
This patch moves the minimal range calculation out of the arm64 code
and into the generic implementation, simplifying zap_pte_range in the
process (which no longer needs to care about start/end, since they will
point to the appropriate ranges already). With the range being tracked
by core code, the need_flush flag is dropped in favour of checking that
the end of the range has actually been set.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7132813c38 ]
Current implementation doesn't zero out the pages allocated.
Honor the __GFP_ZERO flag and zero out if set.
Cc: <stable@vger.kernel.org> # v3.14+
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2077cef4d5 ]
Firstly, handle zero length calls properly. Believe it or not there
are a few of these happening during early boot.
Next, we can't just drop to a memcpy() call in the forward copy case
where dst <= src. The reason is that the cache initializing stores
used in the Niagara memcpy() implementations can end up clearing out
cache lines before we've sourced their original contents completely.
For example, considering NG4memcpy, the main unrolled loop begins like
this:
load src + 0x00
load src + 0x08
load src + 0x10
load src + 0x18
load src + 0x20
store dst + 0x00
Assume dst is 64 byte aligned and let's say that dst is src - 8 for
this memcpy() call. That store at the end there is the one to the
first line in the cache line, thus clearing the whole line, which thus
clobbers "src + 0x28" before it even gets loaded.
To avoid this, just fall through to a simple copy only mildly
optimized for the case where src and dst are 8 byte aligned and the
length is a multiple of 8 as well. We could get fancy and call
GENmemcpy() but this is good enough for how this thing is actually
used.
Reported-by: David Ahern <david.ahern@oracle.com>
Reported-by: Bob Picco <bpicco@meloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 31aaa98c24 ]
With the increase in number of CPUs calls to functions that dump
output to console (e.g., arch_trigger_all_cpu_backtrace) can take
a long time to complete. If IRQs are disabled eventually the NMI
watchdog kicks in and creates more havoc. Avoid by telling the NMI
watchdog everything is ok.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d51291cb8f ]
Currently perf-stat (aka, counting mode) does not work:
$ perf stat ls
...
Performance counter stats for 'ls':
1.585665 task-clock (msec) # 0.580 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.054 M/sec
<not supported> cycles
<not supported> stalled-cycles-frontend
<not supported> stalled-cycles-backend
<not supported> instructions
<not supported> branches
<not supported> branch-misses
0.002735100 seconds time elapsed
The reason is that state is never reset (stays with PERF_HES_UPTODATE set).
Add a call to sparc_pmu_enable_event during the added_event handling.
Clean up the encoding since pmu_start calls sparc_pmu_enable_event which
does the same. Passing PERF_EF_RELOAD to sparc_pmu_start means the call
to sparc_perf_event_set_period can be removed as well.
With this patch:
$ perf stat ls
...
Performance counter stats for 'ls':
1.552890 task-clock (msec) # 0.552 CPUs utilized
24 context-switches # 0.015 M/sec
0 cpu-migrations # 0.000 K/sec
86 page-faults # 0.055 M/sec
5,748,997 cycles # 3.702 GHz
<not supported> stalled-cycles-frontend:HG
<not supported> stalled-cycles-backend:HG
1,684,362 instructions:HG # 0.29 insns per cycle
295,133 branches:HG # 190.054 M/sec
28,007 branch-misses:HG # 9.49% of all branches
0.002815665 seconds time elapsed
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5b0d4b5514 ]
perf_pmu_disable is called by core perf code before pmu->del and the
enable function is called by core perf code afterwards. No need to
call again within sparc_pmu_del.
Ditto for pmu->add and sparc_pmu_add.
Signed-off-by: David Ahern <david.ahern@oracle.com>
Acked-by: Bob Picco <bob.picco@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 53eb251697 ]
A bug was reported that the semtimedop() system call was always
failing eith ENOSYS.
Since SEMCTL is defined as 3, and SEMTIMEDOP is defined as 4,
the comparison "call <= SEMCTL" will always prevent SEMTIMEDOP
from getting through to the semaphore ops switch statement.
This is corrected by changing the comparison to "call <= SEMTIMEDOP".
Orabug: 20633375
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 66d0f7ec9f ]
Load balancing can be triggered in the critical sections protected by
srmmu_context_spinlock in destroy_context() and switch_mm() and can hang
the cpu waiting for the rq lock of another cpu that in turn has called
switch_mm hangning on srmmu_context_spinlock leading to deadlock.
So, disable interrupt while taking srmmu_context_spinlock in
destroy_context() and switch_mm() so we don't deadlock.
See also commit 77b838fa1e ("[SPARC64]: destroy_context() needs to disable
interrupts.")
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 6f963ec2d6 upstream.
When unbinding and rebinding the driver on a system with a card in PHB0, this
error condition is reached after a few attempts:
ERROR: Bad of_node_put() on /pciex@3fffe40000000
CPU: 0 PID: 3040 Comm: bash Not tainted 3.18.0-rc3-12545-g3627ffe #152
Call Trace:
[c000000721acb5c0] [c00000000086ef94] .dump_stack+0x84/0xb0 (unreliable)
[c000000721acb640] [c00000000073a0a8] .of_node_release+0xd8/0xe0
[c000000721acb6d0] [c00000000044bc44] .kobject_release+0x74/0xe0
[c000000721acb760] [c0000000007394fc] .of_node_put+0x1c/0x30
[c000000721acb7d0] [c000000000545cd8] .cxl_probe+0x1a98/0x1d50
[c000000721acb900] [c0000000004845a0] .local_pci_probe+0x40/0xc0
[c000000721acb980] [c000000000484998] .pci_device_probe+0x128/0x170
[c000000721acba30] [c00000000052400c] .driver_probe_device+0xac/0x2a0
[c000000721acbad0] [c000000000522468] .bind_store+0x108/0x160
[c000000721acbb70] [c000000000521448] .drv_attr_store+0x38/0x60
[c000000721acbbe0] [c000000000293840] .sysfs_kf_write+0x60/0xa0
[c000000721acbc50] [c000000000292500] .kernfs_fop_write+0x140/0x1d0
[c000000721acbcf0] [c000000000208648] .vfs_write+0xd8/0x260
[c000000721acbd90] [c000000000208b18] .SyS_write+0x58/0x100
[c000000721acbe30] [c000000000009258] syscall_exit+0x0/0x98
We are missing a call to of_node_get(). pnv_pci_to_phb_node() should
call of_node_get() otherwise np's reference count isn't incremented and
it might go away. Rename pnv_pci_to_phb_node() to pnv_pci_get_phb_node()
so it's clear it calls of_node_get().
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13648b0118 upstream.
/proc/<pid>/maps currently don't annotate stack vma with "[stack]"
This is because KSTK_ESP ie expected to return usermode SP of tsk while
currently it returns the kernel mode SP of a sleeping tsk.
While the fix is trivial, we also need to adjust the ARC kernel stack
unwinder to not use KSTK_SP and friends any more.
Reported-and-suggested-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit b3cffac04e upstream.
Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.
Lets save the actual PC in the structure so that the correct value is
accessible later.
Fixes: 669e846e6c ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 4ff6f8e61e upstream.
This has been broken for a long time: it broke first in 2.6.35, then was
almost fixed in 2.6.36 but this one-liner slipped through the cracks.
The bug shows up as an infinite loop in Windows 7 (and newer) boot on
32-bit hosts without EPT.
Windows uses CMPXCHG8B to write to page tables, which causes a
page fault if running without EPT; the emulator is then called from
kvm_mmu_page_fault. The loop then happens if the higher 4 bytes are
not 0; the common case for this is that the NX bit (bit 63) is 1.
Fixes: 6550e1f165
Fixes: 16518d5ada
Reported-by: Erik Rull <erik.rull@rdsoftware.de>
Tested-by: Erik Rull <erik.rull@rdsoftware.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 06c8173eb9 upstream.
Commit:
f31a9f7c71 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area")
introduced alternative instructions for XSAVES/XRSTORS and commit:
adb9d526e9 ("x86/xsaves: Add xsaves and xrstors support for booting time")
added support for the XSAVES/XRSTORS instructions at boot time.
Unfortunately both failed to properly protect them against faulting:
The 'xstate_fault' macro will use the closest label named '1'
backward and that ends up in the .altinstr_replacement section
rather than in .text. This means that the kernel will never find
in the __ex_table the .text address where this instruction might
fault, leading to serious problems if userspace manages to
trigger the fault.
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Jamie Iles <jamie.iles@oracle.com>
[ Improved the changelog, fixed some whitespace noise. ]
Acked-by: Borislav Petkov <bp@alien8.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Allan Xavier <mr.a.xavier@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: adb9d526e9 ("x86/xsaves: Add xsaves and xrstors support for booting time")
Fixes: f31a9f7c71 ("x86/xsaves: Use xsaves/xrstors to save and restore xsave area")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 956421fbb7 upstream.
'ret_from_fork' checks TIF_IA32 to determine whether 'pt_regs' and
the related state make sense for 'ret_from_sys_call'. This is
entirely the wrong check. TS_COMPAT would make a little more
sense, but there's really no point in keeping this optimization
at all.
This fixes a return to the wrong user CS if we came from int
0x80 in a 64-bit task.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4710be56d76ef994ddf59087aad98c000fbab9a4.1424989793.git.luto@amacapital.net
[ Backported from tip:x86/asm. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 1ea76fbadd upstream.
Commit b568b8601f ("Treat SCI interrupt as normal GSI interrupt")
accidently removes support of legacy PIC interrupt when fixing a
regression for Xen, which causes a nasty regression on HP/Compaq
nc6000 where we fail to register the ACPI interrupt, and thus
lose eg. thermal notifications leading a potentially overheated
machine.
So reintroduce support of legacy PIC based ACPI SCI interrupt.
Reported-by: Ville Syrjälä <syrjala@sci.fi>
Tested-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: linux-pm@vger.kernel.org
Link: http://lkml.kernel.org/r/1424052673-22974-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b43d7125f upstream.
pmc_dbgfs_unregister() will be called when pmc->dbgfs_dir is unconditionally
NULL on error path in pmc_dbgfs_register(). To prevent this we move the
assignment to where is should be.
Fixes: f855911c1f (x86/pmc_atom: Expose PMC device state and platform sleep state)
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Kumar P. Mahesh <mahesh.kumar.p@intel.com>
Link: http://lkml.kernel.org/r/1421253575-22509-2-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e7c22d447 upstream.
The issue is that the stack for processes is not properly randomized on
64 bit architectures due to an integer overflow.
The affected function is randomize_stack_top() in file
"fs/binfmt_elf.c":
static unsigned long randomize_stack_top(unsigned long stack_top)
{
unsigned int random_variable = 0;
if ((current->flags & PF_RANDOMIZE) &&
!(current->personality & ADDR_NO_RANDOMIZE)) {
random_variable = get_random_int() & STACK_RND_MASK;
random_variable <<= PAGE_SHIFT;
}
return PAGE_ALIGN(stack_top) + random_variable;
return PAGE_ALIGN(stack_top) - random_variable;
}
Note that, it declares the "random_variable" variable as "unsigned int".
Since the result of the shifting operation between STACK_RND_MASK (which
is 0x3fffff on x86_64, 22 bits) and PAGE_SHIFT (which is 12 on x86_64):
random_variable <<= PAGE_SHIFT;
then the two leftmost bits are dropped when storing the result in the
"random_variable". This variable shall be at least 34 bits long to hold
the (22+12) result.
These two dropped bits have an impact on the entropy of process stack.
Concretely, the total stack entropy is reduced by four: from 2^28 to
2^30 (One fourth of expected entropy).
This patch restores back the entropy by correcting the types involved
in the operations in the functions randomize_stack_top() and
stack_maxrandom_size().
The successful fix can be tested with:
$ for i in `seq 1 10`; do cat /proc/self/maps | grep stack; done
7ffeda566000-7ffeda587000 rw-p 00000000 00:00 0 [stack]
7fff5a332000-7fff5a353000 rw-p 00000000 00:00 0 [stack]
7ffcdb7a1000-7ffcdb7c2000 rw-p 00000000 00:00 0 [stack]
7ffd5e2c4000-7ffd5e2e5000 rw-p 00000000 00:00 0 [stack]
...
Once corrected, the leading bytes should be between 7ffc and 7fff,
rather than always being 7fff.
Signed-off-by: Hector Marco-Gisbert <hecmargi@upv.es>
Signed-off-by: Ismael Ripoll <iripoll@upv.es>
[ Rebased, fixed 80 char bugs, cleaned up commit message, added test example and CVE ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: CVE-2015-1593
Link: http://lkml.kernel.org/r/20150214173350.GA18393@www.outflux.net
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96738c69a7 upstream.
Andy pointed out that if an NMI or MCE is received while we're in the
middle of an EFI mixed mode call a triple fault will occur. This can
happen, for example, when issuing an EFI mixed mode call while running
perf.
The reason for the triple fault is that we execute the mixed mode call
in 32-bit mode with paging disabled but with 64-bit kernel IDT handlers
installed throughout the call.
At Andy's suggestion, stop playing the games we currently do at runtime,
such as disabling paging and installing a 32-bit GDT for __KERNEL_CS. We
can simply switch to the __KERNEL32_CS descriptor before invoking
firmware services, and run in compatibility mode. This way, if an
NMI/MCE does occur the kernel IDT handler will execute correctly, since
it'll jump to __KERNEL_CS automatically.
However, this change is only possible post-ExitBootServices(). Before
then the firmware "owns" the machine and expects for its 32-bit IDT
handlers to be left intact to service interrupts, etc.
So, we now need to distinguish between early boot and runtime
invocations of EFI services. During early boot, we need to restore the
GDT that the firmware expects to be present. We can only jump to the
__KERNEL32_CS code segment for mixed mode calls after ExitBootServices()
has been invoked.
A liberal sprinkling of comments in the thunking code should make the
differences in early and late environments more apparent.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2996cb29b upstream.
The KSTK_EIP() and KSTK_ESP() macros should return the user program
counter (PC) and stack pointer (A0StP) of the given task. These are used
to determine which VMA corresponds to the user stack in
/proc/<pid>/maps, and for the user PC & A0StP in /proc/<pid>/stat.
However for Meta the PC & A0StP from the task's kernel context are used,
resulting in broken output. For example in following /proc/<pid>/maps
output, the 3afff000-3b021000 VMA should be described as the stack:
# cat /proc/self/maps
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0
And in the following /proc/<pid>/stat output, the PC is in kernel code
(1074234964 = 0x40078654) and the A0StP is in the kernel heap
(1335981392 = 0x4fa17550):
# cat /proc/self/stat
51 (cat) R ... 1335981392 1074234964 ...
Fix the definitions of KSTK_EIP() and KSTK_ESP() to use
task_pt_regs(tsk)->ctx rather than (tsk)->thread.kernel_context. This
gets the registers from the user context stored after the thread info at
the base of the kernel stack, which is from the last entry into the
kernel from userland, regardless of where in the kernel the task may
have been interrupted, which results in the following more correct
/proc/<pid>/maps output:
# cat /proc/self/maps
...
0800b000-08070000 r-xp 00000000 00:02 207 /lib/libuClibc-0.9.34-git.so
...
100b0000-100b1000 rwxp 00000000 00:00 0 [heap]
3afff000-3b021000 rwxp 00000000 00:00 0 [stack]
And /proc/<pid>/stat now correctly reports the PC in libuClibc
(134320308 = 0x80190b4) and the A0StP in the [stack] region (989864576 =
0x3b002280):
# cat /proc/self/stat
51 (cat) R ... 989864576 134320308 ...
Reported-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d42d48a34 upstream.
The native (64-bit) sigval_t union contains sival_int (32-bit) and
sival_ptr (64-bit). When a compat application invokes a syscall that
takes a sigval_t value (as part of a larger structure, e.g.
compat_sys_mq_notify, compat_sys_timer_create), the compat_sigval_t
union is converted to the native sigval_t with sival_int overlapping
with either the least or the most significant half of sival_ptr,
depending on endianness. When the corresponding signal is delivered to a
compat application, on big endian the current (compat_uptr_t)sival_ptr
cast always returns 0 since sival_int corresponds to the top part of
sival_ptr. This patch fixes copy_siginfo_to_user32() so that sival_int
is copied to the compat_siginfo_t structure.
Reported-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Tested-by: Bamvor Jian Zhang <bamvor.zhangjian@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a52d209336 upstream.
Since the removal of CONFIG_REGULATOR_DUMMY option, the touchscreen stopped
working. This patch enables the "replacement" for REGULATOR_DUMMY and
allows the touchscreen to work even though there is no regulator for "vcc".
Signed-off-by: Martin Vajnar <martin.vajnar@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b568b8601f upstream.
Currently Xen Domain0 has special treatment for ACPI SCI interrupt,
that is initialize irq for ACPI SCI at early stage in a special way as:
xen_init_IRQ()
->pci_xen_initial_domain()
->xen_setup_acpi_sci()
Allocate and initialize irq for ACPI SCI
Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq
number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on
IOAPIC irqdomains through following path
acpi_gsi_to_irq()
->mp_map_gsi_to_irq()
->mp_map_pin_to_irq()
->check IOAPIC irqdomain
For PV domains, it uses Xen event based interrupt manangement and
doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC.
This causes Xen domain0 fail to install interrupt handler for ACPI SCI
and all ACPI events will be lost. Please refer to:
https://lkml.org/lkml/2014/12/19/178
So the fix is to get rid of special treatment for ACPI SCI, just treat
ACPI SCI as normal GSI interrupt as:
acpi_gsi_to_irq()
->acpi_register_gsi()
->acpi_register_gsi_xen()
->xen_register_gsi()
With above change, there's no need for xen_setup_acpi_sci() anymore.
The above change also works with bare metal kernel too.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: xen-devel@lists.xenproject.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1421720467-7709-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 428d53be5e upstream.
We have to delete the allocated interrupt info if __inject_vm() fails.
Otherwise user space can keep flooding kvm with floating interrupts and
provoke more and more memory leaks.
Reported-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2207cdd0 upstream.
If a vm with no VCPUs is created, the injection of a floating irq
leads to an endless loop in the kernel.
Let's skip the search for a destination VCPU for a floating irq if no
VCPUs were created.
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ac96caf0f upstream.
The hrtimer that handles the wait with enabled timer interrupts
should not be disturbed by changes of the host time.
This patch changes our hrtimer to be based on a monotonic clock.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d00f75942 upstream.
Patch 0759d0681c ("KVM: s390: cleanup handle_wait by reusing
kvm_vcpu_block") changed the way pending guest clock comparator
interrupts are detected. It was assumed that as soon as the hrtimer
wakes up, the condition for the guest ckc is satisfied.
This is however only true as long as adjclock() doesn't speed
up the monotonic clock. Reason is that the hrtimer is based on
CLOCK_MONOTONIC, the guest clock comparator detection is based
on the raw TOD clock. If CLOCK_MONOTONIC runs faster than the
TOD clock, the hrtimer wakes the target VCPU up too early and
the target VCPU will not detect any pending interrupts, therefore
going back to sleep. It will never be woken up again because the
hrtimer has finished. The VCPU is stuck.
As a quick fix, we have to forward the hrtimer until the guest
clock comparator is really due, to guarantee properly timed wake
ups.
As the hrtimer callback might be triggered on another cpu, we
have to make sure that the timer is really stopped and not currently
executing the callback on another cpu. This can happen if the vcpu
thread is scheduled onto another physical cpu, but the timer base
is not migrated. So lets use hrtimer_cancel instead of try_to_cancel.
A proper fix might be to introduce a RAW based hrtimer.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f187922dd upstream.
When the guest writes to the TSC, the masterclock TSC copy must be
updated as well along with the TSC_OFFSET update, otherwise a negative
tsc_timestamp is calculated at kvm_guest_time_update.
Once "if (!vcpus_matched && ka->use_master_clock)" is simplified to
"if (ka->use_master_clock)", the corresponding "if (!ka->use_master_clock)"
becomes redundant, so remove the do_request boolean and collapse
everything into a single condition.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed4cbc81ad upstream.
activate_mm() and switch_mm() call get_new_mmu_context() which in turn
can enable the HTW before the entryhi is changed with the new ASID.
Since the latter will enable the HTW in local_flush_tlb_all(),
then there is a small timing window where the HTW is running with the
new ASID but with an old pgd since the TLBMISS_HANDLER_SETUP_PGD
hasn't assigned a new one yet. In order to prevent that, we introduce a
simple htw counter to avoid starting HTW accidentally due to nested
htw_{start,stop}() sequences. Moreover, since various IPI calls can
enforce TLB flushing operations on a different core, such an operation
may interrupt another htw_{stop,start} in progress leading inconsistent
updates of the htw_seq variable. In order to avoid that, we disable the
interrupts whenever we update that variable.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9118/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06f34e1c28 upstream.
We used to calculate page address differently in 2 cases:
1. In virt_to_page(x) we do
--->8---
mem_map + (x - CONFIG_LINUX_LINK_BASE) >> PAGE_SHIFT
--->8---
2. In in pte_page(x) we do
--->8---
mem_map + (pte_val(x) - PAGE_OFFSET) >> PAGE_SHIFT
--->8---
That leads to problems in case PAGE_OFFSET != CONFIG_LINUX_LINK_BASE -
different pages will be selected depending on where and how we calculate
page address.
In particular in the STAR 9000853582 when gdb attempted to read memory
of another process it got improper page in get_user_pages() because this
is exactly one of the places where we search for a page by pte_page().
The fix is trivial - we need to calculate page address similarly in both
cases.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 165235180f upstream.
mvebu_armada375_smp_wa_init is only used on armada 375 but is defined
for all mvebu machines. As it calls a function that is only provided
sometimes, this can result in a link error:
arch/arm/mach-mvebu/built-in.o: In function `mvebu_armada375_smp_wa_init':
:(.text+0x228): undefined reference to `mvebu_setup_boot_addr_wa'
To solve this, we can just change the existing #ifdef around the
function to also check for Armada375 SMP platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 305969fb62 ("ARM: mvebu: use the common function for Armada 375 SMP workaround")
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95fcedb027 upstream.
The vexpress tc2 power management code calls mcpm_loopback, which
is only available if ARM_CPU_SUSPEND is enabled, otherwise we
get a link error:
arch/arm/mach-vexpress/built-in.o: In function `tc2_pm_init':
arch/arm/mach-vexpress/tc2_pm.c:389: undefined reference to `mcpm_loopback'
This explicitly selects ARM_CPU_SUSPEND like other platforms that
need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 3592d7e002 ("ARM: 8082/1: TC2: test the MCPM loopback during boot")
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bc78f32c2 upstream.
Add regulator_has_full_constraints() call to poodle board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.
This fixes the following warnings that can be seen on poodle if
regulators are enabled:
ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 271e80176a upstream.
Add regulator_has_full_constraints() call to corgi board file to let
regulator core know that we do not have any additional regulators left.
This lets it substitute unprovided regulators with dummy ones.
This fixes the following warnings that can be seen on corgi if
regulators are enabled:
ads7846 spi1.0: unable to get regulator: -517
spi spi1.0: Driver ads7846 requests probe deferral
wm8731 0-001b: Failed to get supply 'AVDD': -517
wm8731 0-001b: Failed to request supplies: -517
wm8731 0-001b: ASoC: failed to probe component -517
corgi-audio corgi-audio: ASoC: failed to instantiate card -517
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91117a2024 upstream.
The 'pfn' returned by axonram was completely bogus, and has been since
2008.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9df11828d9 upstream.
The L2 cache properties were completely off with respect to what the
hardware is configured for. Fix the cache-size, cache-line-size and
cache-sets to reflect the L2 cache controller we have: 512KB, 16 ways
and 32 bytes per cache-line.
Fixes: 46d4bca044 ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67fd14b3ec upstream.
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de47699d00 upstream.
Commit 58ecb23f64 ("ARM: tegra: add missing unit addresses to DT") added
unit address and changed reg base for GR3D and DSI host1x modules, but these
addresses belongs to GR2D and TVO modules respectively. Fix it by changing
modules unit and reg base addresses to proper ones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: 58ecb23f64 (ARM: tegra: add missing unit addresses to DT)
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c7e36bfc3 upstream.
With commit '7dedd34: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset()
with DEBUG_LL' we moved from parsing cmdline to identify uart used
for earlycon to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.
On DRA7 UART3 hwmod doesn't have this flag enabled, and atleast on
BeagleBoard-X15, where we use UART3 for console, boot fails with
DEBUG_LL enabled. Enable DEBUG_OMAP4UART3_FLAGS for UART3 hwmod.
For using DEBUG_LL, enable CONFIG_DEBUG_OMAP4UART3 in menuconfig.
Fixes: 90020c7b2c ("ARM: OMAP: DRA7: hwmod: Create initial DRA7XX SoC data")
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e461894dc2 upstream.
StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbef8478be upstream.
Migrating hugepages and hwpoisoned hugepages are considered as non-present
hugepages, and they are referenced via migration entries and hwpoison
entries in their page table slots.
This behavior causes race condition because pmd_huge() doesn't tell
non-huge pages from migrating/hwpoisoned hugepages. follow_page_mask() is
one example where the kernel would call follow_page_pte() for such
hugepage while this function is supposed to handle only normal pages.
To avoid this, this patch makes pmd_huge() return true when pmd_none() is
true *and* pmd_present() is false. We don't have to worry about mixing up
non-present pmd entry with normal pmd (pointing to leaf level pte entry)
because pmd_present() is true in normal pmd.
The same race condition could happen in (x86-specific) gup_pmd_range(),
where this patch simply adds pmd_present() check instead of pmd_huge().
This is because gup_pmd_range() is fast path. If we have non-present
hugepage in this function, we will go into gup_huge_pmd(), then return 0
at flag mask check, and finally fall back to the slow path.
Fixes: 290408d4a2 ("hugetlb: hugepage migration core")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca5d25642e upstream.
Export the _save_msa asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m and
CONFIG_CPU_HAS_MSA=y due to commit f798217dfd ("KVM: MIPS: Don't leak
FPU/DSP to guest"):
ERROR: "_save_msa" [arch/mips/kvm/kvm.ko] undefined!
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ce465e04b upstream.
Export the _save_fp asm function used by the lose_fpu(1) macro to GPL
modules so that KVM can make use of it when it is built as a module.
This fixes the following build error when CONFIG_KVM=m due to commit
f798217dfd ("KVM: MIPS: Don't leak FPU/DSP to guest"):
ERROR: "_save_fp" [arch/mips/kvm/kvm.ko] undefined!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: f798217dfd (KVM: MIPS: Don't leak FPU/DSP to guest)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9260/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fde3538a8a upstream.
Whenever we modify a page table entry, we need to ensure that the HTW
will not fetch a stable entry. And for that to happen we need to ensure
that HTW is stopped before we modify the said entry otherwise the HTW
may already be in the process of reading that entry and fetching the
old information. As a result of which, we replace the htw_reset() calls
with htw_{stop,start} in more appropriate places. This also removes the
remaining users of htw_reset() and as a result we drop that macro
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9116/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 461d1597ff upstream.
When we use htw_{start,stop}() outside of htw_reset(), we need
to ensure that c0 changes have been propagated properly before
we attempt to continue with subsequence memory operations.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9114/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98a833c1fa upstream.
The "add" instruction is actually a macro in binutils and depending on
the size of the immediate it can expand to an "addi" instruction.
However, the "addi" instruction traps on overflows which is not
something we want on address calculation.
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00121.html
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acac4108df upstream.
The "addi" instruction will trap on overflows which is not something
we need in this code, so we replace that with "addiu".
Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00430.html
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 69e4e63ec8 upstream.
The current code uses bits 0-6 of the sys_cpupll register to calculate
core clock speed. However this is only valid on Au1300, on all earlier
models the hardware only uses bits 0-5 to generate core clock.
This fixes clock calculation on the MTX1 (Au1500), where bit 6 of cpupll
is set as well, which ultimately lead the code to calculate a bogus cpu
core clock and also uart base clock down the line.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reported-by: John Crispin <blogic@openwrt.org>
Tested-by: Bruno Randolf <br1@einfach.org>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/9279/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f798217dfd upstream.
The FPU and DSP are enabled via the CP0 Status CU1 and MX bits by
kvm_mips_set_c0_status() on a guest exit, presumably in case there is
active state that needs saving if pre-emption occurs. However neither of
these bits are cleared again when returning to the guest.
This effectively gives the guest access to the FPU/DSP hardware after
the first guest exit even though it is not aware of its presence,
allowing FP instructions in guest user code to intermittently actually
execute instead of trapping into the guest OS for emulation. It will
then read & manipulate the hardware FP registers which technically
belong to the user process (e.g. QEMU), or are stale from another user
process. It can also crash the guest OS by causing an FP exception, for
which a guest exception handler won't have been registered.
First lets save and disable the FPU (and MSA) state with lose_fpu(1)
before entering the guest. This simplifies the problem, especially for
when guest FPU/MSA support is added in the future, and prevents FR=1 FPU
state being live when the FR bit gets cleared for the guest, which
according to the architecture causes the contents of the FPU and vector
registers to become UNPREDICTABLE.
We can then safely remove the enabling of the FPU in
kvm_mips_set_c0_status(), since there should never be any active FPU or
MSA state to save at pre-emption, which should plug the FPU leak.
DSP state is always live rather than being lazily restored, so for that
it is simpler to just clear the MX bit again when re-entering the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4c6f2cad9 upstream.
Ensure any hardware page table walker (HTW) is disabled while in KVM
guest mode, as KVM doesn't yet set up hardware page table walking for
guest mappings so the wrong mappings would get loaded, resulting in the
guest hanging or crashing once it reaches userland.
The HTW is disabled and re-enabled around the call to
__kvm_mips_vcpu_run() which does the initial switch into guest mode and
the final switch out of guest context. Additionally it is enabled for
the duration of guest exits (i.e. kvm_mips_handle_exit()), getting
disabled again before returning back to guest or host.
In all cases the HTW is only disabled in normal kernel mode while
interrupts are disabled, so that the HTW doesn't get left disabled if
the process is preempted.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
