[ Upstream commit a58d882841 ]
The mv88e6xxx has an internal PPU that polls PHY state. If we want to
access the internal PHYs, we need to disable the PPU first. Because
that is a slow operation, a 10ms timer is used to re-enable it,
canceled with every access, so bulk operations effectively only
disable it once and re-enable it some 10ms after the last access.
If a PHY is accessed and then the mv88e6xxx module is removed before
the 10ms are up, the PPU re-enable ends up accessing a dangling pointer.
This especially affects probing during bootup. The MDIO bus and PHY
registration may succeed, but registration with the DSA framework
may fail later on (e.g. because the CPU port depends on another,
very slow device that isn't done probing yet, returning -EPROBE_DEFER).
In this case, probe() fails, but the MDIO subsystem may already have
accessed the MIDO bus or PHYs, arming the timer.
This is fixed as follows:
- If probe fails after mv88e6xxx_phy_init(), make sure we also call
mv88e6xxx_phy_destroy() before returning
- In mv88e6xxx_remove(), make sure we do the teardown in the correct
order, calling mv88e6xxx_phy_destroy() after unregistering the
switch device.
- In mv88e6xxx_phy_destroy(), destroy both the timer and the work item
that the timer might schedule, synchronously waiting in case one of
the callbacks already fired and destroying the timer first, before
waiting for the work item.
- Access to the PPU is guarded by a mutex, the worker acquires it
with a mutex_trylock(), not proceeding with the expensive shutdown
if that fails. We grab the mutex in mv88e6xxx_phy_destroy() to make
sure the slow PPU shutdown is already done or won't even enter, when
we wait for the work item.
Fixes: 2e5f032095 ("dsa: add support for the Marvell 88E6131 switch chip")
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250401135705.92760-1-david.oberhollenzer@sigma-star.at
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ac6ea4a3e ]
Using RTEXT_FILTER_SKIP_STATS is incorrectly skipping non-stats IPv6
netlink attributes on link dump. This causes issues on userspace tools,
e.g iproute2 is not rendering address generation mode as it should due
to missing netlink attribute.
Move the filling of IFLA_INET6_STATS and IFLA_INET6_ICMP6STATS to a
helper function guarded by a flag check to avoid hitting the same
situation in the future.
Fixes: d5566fd72e ("rtnetlink: RTEXT_FILTER_SKIP_STATS support to avoid dumping inet/inet6 stats")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250402121751.3108-1-ffmancera@riseup.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a0a3ff659 ]
Upstream fix ac888d5886 ("net: do not delay dst_entries_add() in
dst_release()") moved decrementing the dst count from dst_destroy to
dst_release to avoid accessing already freed data in case of netns
dismantle. However in case CONFIG_DST_CACHE is enabled and OvS+tunnels
are used, this fix is incomplete as the same issue will be seen for
cached dsts:
Unable to handle kernel paging request at virtual address ffff5aabf6b5c000
Call trace:
percpu_counter_add_batch+0x3c/0x160 (P)
dst_release+0xec/0x108
dst_cache_destroy+0x68/0xd8
dst_destroy+0x13c/0x168
dst_destroy_rcu+0x1c/0xb0
rcu_do_batch+0x18c/0x7d0
rcu_core+0x174/0x378
rcu_core_si+0x18/0x30
Fix this by invalidating the cache, and thus decrementing cached dst
counters, in dst_release too.
Fixes: d71785ffc7 ("net: add dst_cache to ovs vxlan lwtunnel")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Link: https://patch.msgid.link/20250326173634.31096-1-atenart@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8930424777 ]
Because skb_tunnel_check_pmtu() doesn't handle PACKET_HOST packets,
commit 30a92c9e3d ("openvswitch: Set the skbuff pkt_type for proper
pmtud support.") forced skb->pkt_type to PACKET_OUTGOING for
openvswitch packets that are sent using the OVS_ACTION_ATTR_OUTPUT
action. This allowed such packets to invoke the
iptunnel_pmtud_check_icmp() or iptunnel_pmtud_check_icmpv6() helpers
and thus trigger PMTU update on the input device.
However, this also broke other parts of PMTU discovery. Since these
packets don't have the PACKET_HOST type anymore, they won't trigger the
sending of ICMP Fragmentation Needed or Packet Too Big messages to
remote hosts when oversized (see the skb_in->pkt_type condition in
__icmp_send() for example).
These two skb->pkt_type checks are therefore incompatible as one
requires skb->pkt_type to be PACKET_HOST, while the other requires it
to be anything but PACKET_HOST.
It makes sense to not trigger ICMP messages for non-PACKET_HOST packets
as these messages should be generated only for incoming l2-unicast
packets. However there doesn't seem to be any reason for
skb_tunnel_check_pmtu() to ignore PACKET_HOST packets.
Allow both cases to work by allowing skb_tunnel_check_pmtu() to work on
PACKET_HOST packets and not overriding skb->pkt_type in openvswitch
anymore.
Fixes: 30a92c9e3d ("openvswitch: Set the skbuff pkt_type for proper pmtud support.")
Fixes: 4cb47a8644 ("tunnels: PMTU discovery support for directly bridged IP packets")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Tested-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/eac941652b86fddf8909df9b3bf0d97bc9444793.1743208264.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fccd2b711d ]
When a peer attempts to establish a connection, vsock_connect() contains
a loop that waits for the state to be TCP_ESTABLISHED. However, the
other peer can be fast enough to accept the connection and close it
immediately, thus moving the state to TCP_CLOSING.
When this happens, the peer in the vsock_connect() is properly woken up,
but since the state is not TCP_ESTABLISHED, it goes back to sleep
until the timeout expires, returning -ETIMEDOUT.
If the socket state is TCP_CLOSING, waiting for the timeout is pointless.
vsock_connect() can return immediately without errors or delay since the
connection actually happened. The socket will be in a closing state,
but this is not an issue, and subsequent calls will fail as expected.
We discovered this issue while developing a test that accepts and
immediately closes connections to stress the transport switch between
two connect() calls, where the first one was interrupted by a signal
(see Closes link).
Reported-by: Luigi Leonardi <leonardi@redhat.com>
Closes: https://lore.kernel.org/virtualization/bq6hxrolno2vmtqwcvb5bljfpb7mvwb3kohrvaed6auz5vxrfv@ijmd2f3grobn/
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Luigi Leonardi <leonardi@redhat.com>
Reviewed-by: Luigi Leonardi <leonardi@redhat.com>
Link: https://patch.msgid.link/20250328141528.420719-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df207de9d9 ]
Matt Dowling reported a weird UDP memory usage issue.
Under normal operation, the UDP memory usage reported in /proc/net/sockstat
remains close to zero. However, it occasionally spiked to 524,288 pages
and never dropped. Moreover, the value doubled when the application was
terminated. Finally, it caused intermittent packet drops.
We can reproduce the issue with the script below [0]:
1. /proc/net/sockstat reports 0 pages
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 1 mem 0
2. Run the script till the report reaches 524,288
# python3 test.py & sleep 5
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 3 mem 524288 <-- (INT_MAX + 1) >> PAGE_SHIFT
3. Kill the socket and confirm the number never drops
# pkill python3 && sleep 5
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 1 mem 524288
4. (necessary since v6.0) Trigger proto_memory_pcpu_drain()
# python3 test.py & sleep 1 && pkill python3
5. The number doubles
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 1 mem 1048577
The application set INT_MAX to SO_RCVBUF, which triggered an integer
overflow in udp_rmem_release().
When a socket is close()d, udp_destruct_common() purges its receive
queue and sums up skb->truesize in the queue. This total is calculated
and stored in a local unsigned integer variable.
The total size is then passed to udp_rmem_release() to adjust memory
accounting. However, because the function takes a signed integer
argument, the total size can wrap around, causing an overflow.
Then, the released amount is calculated as follows:
1) Add size to sk->sk_forward_alloc.
2) Round down sk->sk_forward_alloc to the nearest lower multiple of
PAGE_SIZE and assign it to amount.
3) Subtract amount from sk->sk_forward_alloc.
4) Pass amount >> PAGE_SHIFT to __sk_mem_reduce_allocated().
When the issue occurred, the total in udp_destruct_common() was 2147484480
(INT_MAX + 833), which was cast to -2147482816 in udp_rmem_release().
At 1) sk->sk_forward_alloc is changed from 3264 to -2147479552, and
2) sets -2147479552 to amount. 3) reverts the wraparound, so we don't
see a warning in inet_sock_destruct(). However, udp_memory_allocated
ends up doubling at 4).
Since commit 3cd3399dd7 ("net: implement per-cpu reserves for
memory_allocated"), memory usage no longer doubles immediately after
a socket is close()d because __sk_mem_reduce_allocated() caches the
amount in udp_memory_per_cpu_fw_alloc. However, the next time a UDP
socket receives a packet, the subtraction takes effect, causing UDP
memory usage to double.
This issue makes further memory allocation fail once the socket's
sk->sk_rmem_alloc exceeds net.ipv4.udp_rmem_min, resulting in packet
drops.
To prevent this issue, let's use unsigned int for the calculation and
call sk_forward_alloc_add() only once for the small delta.
Note that first_packet_length() also potentially has the same problem.
[0]:
from socket import *
SO_RCVBUFFORCE = 33
INT_MAX = (2 ** 31) - 1
s = socket(AF_INET, SOCK_DGRAM)
s.bind(('', 0))
s.setsockopt(SOL_SOCKET, SO_RCVBUFFORCE, INT_MAX)
c = socket(AF_INET, SOCK_DGRAM)
c.connect(s.getsockname())
data = b'a' * 100
while True:
c.send(data)
Fixes: f970bd9e3a ("udp: implement memory accounting helpers")
Reported-by: Matt Dowling <madowlin@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250401184501.67377-3-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a465a0da1 ]
__udp_enqueue_schedule_skb() has the following condition:
if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf)
goto drop;
sk->sk_rcvbuf is initialised by net.core.rmem_default and later can
be configured by SO_RCVBUF, which is limited by net.core.rmem_max,
or SO_RCVBUFFORCE.
If we set INT_MAX to sk->sk_rcvbuf, the condition is always false
as sk->sk_rmem_alloc is also signed int.
Then, the size of the incoming skb is added to sk->sk_rmem_alloc
unconditionally.
This results in integer overflow (possibly multiple times) on
sk->sk_rmem_alloc and allows a single socket to have skb up to
net.core.udp_mem[1].
For example, if we set a large value to udp_mem[1] and INT_MAX to
sk->sk_rcvbuf and flood packets to the socket, we can see multiple
overflows:
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 3 mem 7956736 <-- (7956736 << 12) bytes > INT_MAX * 15
^- PAGE_SHIFT
# ss -uam
State Recv-Q ...
UNCONN -1757018048 ... <-- flipping the sign repeatedly
skmem:(r2537949248,rb2147483646,t0,tb212992,f1984,w0,o0,bl0,d0)
Previously, we had a boundary check for INT_MAX, which was removed by
commit 6a1f12dd85 ("udp: relax atomic operation on sk->sk_rmem_alloc").
A complete fix would be to revert it and cap the right operand by
INT_MAX:
rmem = atomic_add_return(size, &sk->sk_rmem_alloc);
if (rmem > min(size + (unsigned int)sk->sk_rcvbuf, INT_MAX))
goto uncharge_drop;
but we do not want to add the expensive atomic_add_return() back just
for the corner case.
Casting rmem to unsigned int prevents multiple wraparounds, but we still
allow a single wraparound.
# cat /proc/net/sockstat | grep UDP:
UDP: inuse 3 mem 524288 <-- (INT_MAX + 1) >> 12
# ss -uam
State Recv-Q ...
UNCONN -2147482816 ... <-- INT_MAX + 831 bytes
skmem:(r2147484480,rb2147483646,t0,tb212992,f3264,w0,o0,bl0,d14468947)
So, let's define rmem and rcvbuf as unsigned int and check skb->truesize
only when rcvbuf is large enough to lower the overflow possibility.
Note that we still have a small chance to see overflow if multiple skbs
to the same socket are processed on different core at the same time and
each size does not exceed the limit but the total size does.
Note also that we must ignore skb->truesize for a small buffer as
explained in commit 363dc73aca ("udp: be less conservative with
sock rmem accounting").
Fixes: 6a1f12dd85 ("udp: relax atomic operation on sk->sk_rmem_alloc")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250401184501.67377-2-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9684407522 ]
Protect the parser TCAM/SRAM memory, and the cached (shadow) SRAM
information, from concurrent modifications.
Both the TCAM and SRAM tables are indirectly accessed by configuring
an index register that selects the row to read or write to. This means
that operations must be atomic in order to, e.g., avoid spreading
writes across multiple rows. Since the shadow SRAM array is used to
find free rows in the hardware table, it must also be protected in
order to avoid TOCTOU errors where multiple cores allocate the same
row.
This issue was detected in a situation where `mvpp2_set_rx_mode()` ran
concurrently on two CPUs. In this particular case the
MVPP2_PE_MAC_UC_PROMISCUOUS entry was corrupted, causing the
classifier unit to drop all incoming unicast - indicated by the
`rx_classifier_drops` counter.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250401065855.3113635-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8fe975fd ]
In the current implementation, skbprio enqueue/dequeue contains an assertion
that fails under certain conditions when SKBPRIO is used as a child qdisc under
TBF with specific parameters. The failure occurs because TBF sometimes peeks at
packets in the child qdisc without actually dequeuing them when tokens are
unavailable.
This peek operation creates a discrepancy between the parent and child qdisc
queue length counters. When TBF later receives a high-priority packet,
SKBPRIO's queue length may show a different value than what's reflected in its
internal priority queue tracking, triggering the assertion.
The fix removes this overly strict assertions in SKBPRIO, they are not
necessary at all.
Reported-by: syzbot+a3422a19b05ea96bee18@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a3422a19b05ea96bee18
Fixes: aea5f654e6 ("net/sched: add skbprio scheduler")
Cc: Nishanth Devarajan <ndev2021@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://patch.msgid.link/20250329222536.696204-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 078aabd567 ]
When calling netlbl_conn_setattr(), addr->sa_family is used
to determine the function behavior. If sk is an IPv4 socket,
but the connect function is called with an IPv6 address,
the function calipso_sock_setattr() is triggered.
Inside this function, the following code is executed:
sk_fullsock(__sk) ? inet_sk(__sk)->pinet6 : NULL;
Since sk is an IPv4 socket, pinet6 is NULL, leading to a
null pointer dereference.
This patch fixes the issue by checking if inet6_sk(sk)
returns a NULL pointer before accessing pinet6.
Signed-off-by: Debin Zhu <mowenroot@163.com>
Signed-off-by: Bitao Ouyang <1985755126@qq.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Fixes: ceba1832b1 ("calipso: Set the calipso socket label to match the secattr.")
Link: https://patch.msgid.link/20250401124018.4763-1-mowenroot@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 688c15017d ]
When nf_tables_updchain encounters an error, hook registration needs to
be rolled back.
This should only be done if the hook has been registered, which won't
happen when the table is flagged as dormant (inactive).
Just move the assignment into the registration block.
Reported-by: syzbot+53ed3a6440173ddbf499@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=53ed3a6440173ddbf499
Fixes: b9703ed44f ("netfilter: nf_tables: support for adding new devices to an existing netdev chain")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d74da1177 ]
conncount has its own GC handler which determines when to reap stale
elements, this is convenient for dynamic sets. However, this also reaps
non-dynamic sets with static configurations coming from control plane.
Always run connlimit gc handler but honor feedback to reap element if
this set is dynamic.
Fixes: 290180e244 ("netfilter: nf_tables: add connlimit support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c9106f490 ]
With SRIOV enabled, idpf ends up calling into idpf_remove() twice.
First via idpf_shutdown() and then again when idpf_remove() calls into
sriov_disable(), because the VF devices use the idpf driver, hence the
same remove routine. When that happens, it is possible for the adapter
to be NULL from the first call to idpf_remove(), leading to a NULL
pointer dereference.
echo 1 > /sys/class/net/<netif>/device/sriov_numvfs
reboot
BUG: kernel NULL pointer dereference, address: 0000000000000020
...
RIP: 0010:idpf_remove+0x22/0x1f0 [idpf]
...
? idpf_remove+0x22/0x1f0 [idpf]
? idpf_remove+0x1e4/0x1f0 [idpf]
pci_device_remove+0x3f/0xb0
device_release_driver_internal+0x19f/0x200
pci_stop_bus_device+0x6d/0x90
pci_stop_and_remove_bus_device+0x12/0x20
pci_iov_remove_virtfn+0xbe/0x120
sriov_disable+0x34/0xe0
idpf_sriov_configure+0x58/0x140 [idpf]
idpf_remove+0x1b9/0x1f0 [idpf]
idpf_shutdown+0x12/0x30 [idpf]
pci_device_shutdown+0x35/0x60
device_shutdown+0x156/0x200
...
Replace the direct idpf_remove() call in idpf_shutdown() with
idpf_vc_core_deinit() and idpf_deinit_dflt_mbx(), which perform
the bulk of the cleanup, such as stopping the init task, freeing IRQs,
destroying the vports and freeing the mailbox. This avoids the calls to
sriov_disable() in addition to a small netdev cleanup, and destroying
workqueues, which don't seem to be required on shutdown.
Reported-by: Yuying Ma <yuma@redhat.com>
Fixes: e850efed5e ("idpf: add module register and probe functionality")
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efaaf344bc ]
Starting from Meteor Lake, the Kumeran interface between the integrated
MAC and the I219 PHY works at a different frequency. This causes sporadic
MDI errors when accessing the PHY, and in rare circumstances could lead
to packet corruption.
To overcome this, introduce minor changes to the Kumeran idle
state (K1) parameters during device initialization. Hardware reset
reverts this configuration, therefore it needs to be applied in a few
places.
Fixes: cc23f4f0b6 ("e1000e: Add support for Meteor Lake")
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e19c1272c8 ]
The lookup table forces the use of the "pinctrl-bcm2835" GPIO chip
provider and essentially assumes that there is going to be such a
provider, and if not, we will fail to set-up the SPI device.
While this is true on Raspberry Pi based systems (2835/36/37, 2711,
2712), this is not true on 7712/77122 Broadcom STB systems which use the
SPI driver, but not the GPIO driver.
There used to be an early check:
chip = gpiochip_find("pinctrl-bcm2835", chip_match_name);
if (!chip)
return 0;
which would accomplish that nicely, bring something similar back by
checking for the compatible strings matched by the pinctrl-bcm2835.c
driver, if there is no Device Tree node matching those compatible
strings, then we won't find any GPIO provider registered by the
"pinctrl-bcm2835" driver.
Fixes: 21f252cd29 ("spi: bcm2835: reduce the abuse of the GPIO API")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250401233603.2938955-1-florian.fainelli@broadcom.com
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8983dc1b66 ]
There is another VivoBook model which built-in mic got broken recently
by the fix of the pin sort. Apply the correct quirk
ALC256_FIXUP_ASUS_MIC_NO_PRESENCE to this model for addressing the
regression, too.
Fixes: 3b4309546b ("ALSA: hda: Fix headset detection failure due to unstable sort")
Closes: https://lore.kernel.org/Z95s5T6OXFPjRnKf@eldamar.lan
Link: https://patch.msgid.link/20250402074208.7347-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d669101052 ]
If we are unable to lookup the chip-select GPIO, the error path will
call bcm2835_spi_cleanup() which unconditionally calls gpiod_put() on
the cs->gpio variable which we just determined was invalid.
Fixes: 21f252cd29 ("spi: bcm2835: reduce the abuse of the GPIO API")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250401224238.2854256-1-florian.fainelli@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 93d34608fd ]
devm_kasprintf() returns NULL when memory allocation fails. Currently,
imx_card_probe() does not check for this case, which results in a NULL
pointer dereference.
Add NULL check after devm_kasprintf() to prevent this issue.
Fixes: aa736700f4 ("ASoC: imx-card: Add imx-card machine driver")
Signed-off-by: Henry Martin <bsdhenrymartin@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250401142510.29900-1-bsdhenrymartin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eada75467f ]
The vectorized io_uring NVMe passthru opcodes don't yet support fixed
buffers. But since userspace can trigger this condition based on the
io_uring SQE parameters, it shouldn't cause a kernel warning.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 23fd22e55b ("nvme: wire up fixed buffer support for nvme passthrough")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f7023171d ]
When a crashkernel is launched on RISC-V, the entry to purgatory is
done by trapping via the stvec CSR. From riscv_kexec_norelocate():
| ...
| /*
| * Switch to physical addressing
| * This will also trigger a jump to CSR_STVEC
| * which in this case is the address of the new
| * kernel.
| */
| csrw CSR_STVEC, a2
| csrw CSR_SATP, zero
stvec requires that the address is 4B aligned, which was not the case,
e.g.:
| Loaded purgatory at 0xffffc000
| kexec_file: kexec_file_load: type:1, start:0xffffd232 head:0x4 flags:0x6
The address 0xffffd232 not 4B aligned.
Correct by adding proper function alignment.
With this change, crashkernels loaded with kexec-file will be able to
properly enter the purgatory.
Fixes: 736e30af58 ("RISC-V: Add purgatory")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20250328085313.1193815-1-bjorn@kernel.org
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 28093cfef5 ]
Commit 58ff537109 ("riscv: Omit optimized string routines when
using KASAN") introduced calls to EXPORT_SYMBOL() in assembly string
routines, which result in R_RISCV_64 relocations against
.export_symbol section. As these rountines are reused by RISC-V
purgatory and our relocator doesn't recognize these relocations, this
fails kexec-file-load with dmesg like
[ 11.344251] kexec_image: Unknown rela relocation: 2
[ 11.345972] kexec_image: Error loading purgatory ret=-8
Let's support R_RISCV_64 relocation to fix kexec on 64-bit RISC-V.
32-bit variant isn't covered since KEXEC_FILE and KEXEC_PURGATORY isn't
available.
Fixes: 58ff537109 ("riscv: Omit optimized string routines when using KASAN")
Signed-off-by: Yao Zi <ziyao@disroot.org>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20250326051445.55131-2-ziyao@disroot.org
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83d78ac677 ]
Ryan sent a fix [1] for arm64 that applies to riscv too: in some hugetlb
functions, we must not use the pte value to get the size of a mapping
because the pte may not be present.
So use the already present size parameter for huge_pte_clear() and the
newly introduced size parameter for huge_ptep_get_and_clear(). And make
sure to gather A/D bits only on present ptes.
Fixes: 82a1a1f3bf ("riscv: mm: support Svnapot in hugetlb page")
Link: https://lore.kernel.org/all/20250217140419.1702389-1-ryan.roberts@arm.com/ [1]
Link: https://lore.kernel.org/r/20250317072551.572169-1-alexghiti@rivosinc.com
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ebd494426 ]
Should an error occur after a successful regulator_bulk_enable() call,
regulator_bulk_disable() should be called, as already done in the remove
function.
Instead of adding an error handling path in the probe, switch from
devm_regulator_bulk_get() to devm_regulator_bulk_get_enable() and
simplify the remove function and some other places accordingly.
Finally, add a missing const when defining rt5665_supply_names to please
checkpatch and constify a few bytes.
Fixes: 33ada14a26 ("ASoC: add rt5665 codec driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/e3c2aa1b2fdfa646752d94f4af968630c0d58248.1742629525.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 121df45b37 ]
When lowcore relocation is enabled, the machine check handler doesn't
use the lowcore address when setting _CIF_MCCK_GUEST. Fix this by
adding the missing base register.
Fixes: 0001b7bbc5 ("s390/entry: Make mchk_int_handler() ready for lowcore relocation")
Reported-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8741d07379 ]
Now ublk driver depends on `ubq->canceling` for deciding if the request
can be dispatched via uring_cmd & io_uring_cmd_complete_in_task().
Once ubq->canceling is set, the uring_cmd can be done via ublk_cancel_cmd()
and io_uring_cmd_done().
So set ubq->canceling when queue is frozen, this way makes sure that the
flag can be observed from ublk_queue_rq() reliably, and avoids
use-after-free on uring_cmd.
Fixes: 216c8f5ef0 ("ublk: replace monitor with cancelable uring_cmd")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250327095123.179113-2-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5322b6ec0 ]
History of the performance regression:
======================================
Since the following series of user copy updates were merged upstream
~2 years ago via:
a562456643 ("Merge branch 'x86-rep-insns': x86 user copy clarifications")
.. copy_user_generic() on x86_64 stopped doing alignment of the
writes to the destination to a 8 byte boundary for the non FSRM case.
Previously, this was done through the ALIGN_DESTINATION macro that
was used in the now removed copy_user_generic_unrolled function.
Turns out this change causes some loss of performance/throughput on
some use cases and specific CPU/platforms without FSRM and ERMS.
Lately I got two reports of performance/throughput issues after a
RHEL 9 kernel pulled the same upstream series with updates to user
copy functions. Both reports consisted of running specific
networking/TCP related testing using iperf3.
Partial upstream fix
====================
The first report was related to a Linux Bridge testing using VMs on a
specific machine with an AMD CPU (EPYC 7402), and after a brief
investigation it turned out that the later change via:
ca96b162bf ("x86: bring back rep movsq for user access on CPUs without ERMS")
... helped/fixed the performance issue.
However, after the later commit/fix was applied, then I got another
regression reported in a multistream TCP test on a 100Gbit mlx5 nic, also
running on an AMD based platform (AMD EPYC 7302 CPU), again that was using
iperf3 to run the test. That regression was after applying the later
fix/commit, but only this didn't help in telling the whole history.
Testing performed to pinpoint residual regression
=================================================
So I narrowed down the second regression use case, but running it
without traffic through a NIC, on localhost, in trying to narrow down
CPU usage and not being limited by other factor like network bandwidth.
I used another system also with an AMD CPU (AMD EPYC 7742). Basically,
I run iperf3 in server and client mode in the same system, for example:
- Start the server binding it to CPU core/thread 19:
$ taskset -c 19 iperf3 -D -s -B 127.0.0.1 -p 12000
- Start the client always binding/running on CPU core/thread 17, using
perf to get statistics:
$ perf stat -o stat.txt taskset -c 17 iperf3 -c 127.0.0.1 -b 0/1000 -V \
-n 50G --repeating-payload -l 16384 -p 12000 --cport 12001 2>&1 \
> stat-19.txt
For the client, always running/pinned to CPU 17. But for the iperf3 in
server mode, I did test runs using CPUs 19, 21, 23 or not pinned to any
specific CPU. So it basically consisted with four runs of the same
commands, just changing the CPU which the server is pinned, or without
pinning by removing the taskset call before the server command. The CPUs
were chosen based on NUMA node they were on, this is the relevant output
of lscpu on the system:
$ lscpu
...
Model name: AMD EPYC 7742 64-Core Processor
...
Caches (sum of all):
L1d: 2 MiB (64 instances)
L1i: 2 MiB (64 instances)
L2: 32 MiB (64 instances)
L3: 256 MiB (16 instances)
NUMA:
NUMA node(s): 4
NUMA node0 CPU(s): 0,1,8,9,16,17,24,25,32,33,40,41,48,49,56,57,64,65,72,73,80,81,88,89,96,97,104,105,112,113,120,121
NUMA node1 CPU(s): 2,3,10,11,18,19,26,27,34,35,42,43,50,51,58,59,66,67,74,75,82,83,90,91,98,99,106,107,114,115,122,123
NUMA node2 CPU(s): 4,5,12,13,20,21,28,29,36,37,44,45,52,53,60,61,68,69,76,77,84,85,92,93,100,101,108,109,116,117,124,125
NUMA node3 CPU(s): 6,7,14,15,22,23,30,31,38,39,46,47,54,55,62,63,70,71,78,79,86,87,94,95,102,103,110,111,118,119,126,127
...
So for the server run, when picking a CPU, I chose CPUs to be not on the same
node. The reason is with that I was able to get/measure relevant
performance differences when changing the alignment of the writes to the
destination in copy_user_generic.
Testing shows up to +81% performance improvement under iperf3
=============================================================
Here's a summary of the iperf3 runs:
# Vanilla upstream alignment:
CPU RATE SYS TIME sender-receiver
Server bind 19: 13.0Gbits/sec 28.371851000 33.233499566 86.9%-70.8%
Server bind 21: 12.9Gbits/sec 28.283381000 33.586486621 85.8%-69.9%
Server bind 23: 11.1Gbits/sec 33.660190000 39.012243176 87.7%-64.5%
Server bind none: 18.9Gbits/sec 19.215339000 22.875117865 86.0%-80.5%
# With the attached patch (aligning writes in non ERMS/FSRM case):
CPU RATE SYS TIME sender-receiver
Server bind 19: 20.8Gbits/sec 14.897284000 20.811101382 75.7%-89.0%
Server bind 21: 20.4Gbits/sec 15.205055000 21.263165909 75.4%-89.7%
Server bind 23: 20.2Gbits/sec 15.433801000 21.456175000 75.5%-89.8%
Server bind none: 26.1Gbits/sec 12.534022000 16.632447315 79.8%-89.6%
So I consistently got better results when aligning the write. The
results above were run on 6.14.0-rc6/rc7 based kernels. The sys is sys
time and then the total time to run/transfer 50G of data. The last
field is the CPU usage of sender/receiver iperf3 process. It's also
worth to note that each pair of iperf3 runs may get slightly different
results on each run, but I always got consistent higher results with
the write alignment for this specific test of running the processes
on CPUs in different NUMA nodes.
Linus Torvalds helped/provided this version of the patch. Initially I
proposed a version which aligned writes for all cases in
rep_movs_alternative, however it used two extra registers and thus
Linus provided an enhanced version that only aligns the write on the
large_movsq case, which is sufficient since the problem happens only
on those AMD CPUs like ones mentioned above without ERMS/FSRM, and
also doesn't require using extra registers. Also, I validated that
aligning only on large_movsq case is really enough for getting the
performance back.
I also tested this patch on an old Intel based non-ERMS/FRMS system
(with Xeon E5-2667 - Sandy Bridge based) and didn't get any problems:
no performance enhancement but also no regression either, using the
same iperf3 based benchmark. Also newer Intel processors after
Sandy Bridge usually have ERMS and should not be affected by this change.
[ mingo: Updated the changelog. ]
Fixes: ca96b162bf ("x86: bring back rep movsq for user access on CPUs without ERMS")
Fixes: 034ff37d34 ("x86: rewrite '__copy_user_nocache' function")
Reported-by: Ondrej Lichtner <olichtne@redhat.com>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20250320142213.2623518-1-herton@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb58e1579f ]
We're trying to mix non-PIC/PIE objects into the otherwise-PIE
relocatable kernels, to avoid GOT/PLT references during early boot
alternative resolution (which happens before the GOT/PLT are set up).
riscv64-unknown-linux-gnu-ld: arch/riscv/errata/sifive/errata.o: relocation R_RISCV_HI20 against `tlb_flush_all_threshold' can not be used when making a shared object; recompile with -fPIC
riscv64-unknown-linux-gnu-ld: arch/riscv/errata/thead/errata.o: relocation R_RISCV_HI20 against `riscv_cbom_block_size' can not be used when making a shared object; recompile with -fPIC
Fixes: 8dc2a7e802 ("riscv: Fix relocatable kernels with early alternatives using -fno-pie")
Link: https://lore.kernel.org/r/20250326224506.27165-2-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84c3c08f5a ]
ASUS VivoBook X515JA with PCI SSID 1043:14f2 also hits the same issue
as other VivoBook model about the mic pin assignment, and the same
workaround is required to apply ALC256_FIXUP_ASUS_MIC_NO_PRESENCE
quirk.
Fixes: 3b4309546b ("ALSA: hda: Fix headset detection failure due to unstable sort")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219902
Link: https://patch.msgid.link/20250326152205.26733-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2593f7e0dc ]
Set ret = 0 on successful completion of the processing loop in
cs_dsp_load() and cs_dsp_load_coeff() to ensure that the function
returns 0 on success.
All normal firmware files will have at least one data block, and
processing this block will set ret == 0, from the result of either
regmap_raw_write() or cs_dsp_parse_coeff().
The kunit tests create a dummy firmware file that contains only the
header, without any data blocks. This gives cs_dsp a file to "load"
that will not cause any side-effects. As there aren't any data blocks,
the processing loop will not set ret == 0.
Originally there was a line after the processing loop:
ret = regmap_async_complete(regmap);
which would set ret == 0 before the function returned.
Commit fe08b7d508 ("firmware: cs_dsp: Remove async regmap writes")
changed the regmap write to a normal sync write, so the call to
regmap_async_complete() wasn't necessary and was removed. It was
overlooked that the ret here wasn't only to check the result of
regmap_async_complete(), it also set the final return value of the
function.
Fixes: fe08b7d508 ("firmware: cs_dsp: Remove async regmap writes")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20250323170529.197205-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8144e9c8f3 ]
Make sure we are not using DB's which were remapped for link status.
Fixes: f6e51c354b ("ntb: intel: split out the gen3 code")
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de203da734 ]
There is a kernel API ntb_mw_clear_trans() would pass 0 to both addr and
size. This would make xlate_pos negative.
[ 23.734156] switchtec switchtec0: MW 0: part 0 addr 0x0000000000000000 size 0x0000000000000000
[ 23.734158] ================================================================================
[ 23.734172] UBSAN: shift-out-of-bounds in drivers/ntb/hw/mscc/ntb_hw_switchtec.c:293:7
[ 23.734418] shift exponent -1 is negative
Ensuring xlate_pos is a positive or zero before BIT.
Fixes: 1e2fd202f8 ("ntb_hw_switchtec: Check for alignment of the buffer in mw_set_trans()")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f1a58ed91 ]
This patch adds parentheses to parameters caller and callee of macros
make_call_t0 and make_call_ra. Every existing invocation of these two
macros uses a single variable for each argument, so the absence of the
parentheses seems okay. However, future invocations might use more
complex expressions as arguments. For example, a future invocation might
look like this: make_call_t0(a - b, c, call). Without parentheses in the
macro definition, the macro invocation expands to:
...
unsigned int offset = (unsigned long) c - (unsigned long) a - b;
...
which is clearly wrong.
The use of parentheses ensures arguments are correctly evaluated and
potentially saves future users of make_call_t0 and make_call_ra debugging
trouble.
Fixes: 6724a76cff ("riscv: ftrace: Reduce the detour code size to half")
Signed-off-by: Juhan Jin <juhan.jin@foxmail.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/tencent_AE90AA59903A628E87E9F80E563DA5BA5508@qq.com
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5cce3fc5 ]
Leak fixes back in 2008 missed one case - if we are trying to set affinity
and spufs_mkdir() fails, we need to drop the reference to neighbor.
Fixes: 58119068cb "[POWERPC] spufs: Fix memory leak on SPU affinity"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c134deabf4 ]
prior to "[POWERPC] spufs: Fix gang destroy leaks" we used to have
a problem with gang lifetimes - creation of a gang returns opened
gang directory, which normally gets removed when that gets closed,
but if somebody has created a context belonging to that gang and
kept it alive until the gang got closed, removal failed and we
ended up with a leak.
Unfortunately, it had been fixed the wrong way. Dentry of gang
directory was no longer pinned, and rmdir on close was gone.
One problem was that failure of open kept calling simple_rmdir()
as cleanup, which meant an unbalanced dput(). Another bug was
in the success case - gang creation incremented link count on
root directory, but that was no longer undone when gang got
destroyed.
Fix consists of
* reverting the commit in question
* adding a counter to gang, protected by ->i_rwsem
of gang directory inode.
* having it set to 1 at creation time, dropped
in both spufs_dir_close() and spufs_gang_close() and bumped
in spufs_create_context(), provided that it's not 0.
* using simple_recursive_removal() to take the gang
directory out when counter reaches zero.
Fixes: 877907d37d "[POWERPC] spufs: Fix gang destroy leaks"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1ca8698ca ]
It's called from spufs_fill_dir(), and caller of that will do
spufs_rmdir() in case of failure. That does remove everything
we'd managed to create, but... the problem dentry is still
negative. IOW, it needs to be explicitly dropped.
Fixes: 3f51dd91c8 "[PATCH] spufs: fix spufs_fill_dir error path"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07c574eb53 ]
Fix netfs_unbuffered_read() to return an ssize_t rather than an int as
netfs_wait_for_read() returns ssize_t and this gets implicitly truncated.
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20250314164201.1993231-5-dhowells@redhat.com
Acked-by: "Paulo Alcantara (Red Hat)" <pc@manguebit.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Viacheslav Dubeyko <slava@dubeyko.com>
cc: Alex Markuze <amarkuze@redhat.com>
cc: Ilya Dryomov <idryomov@gmail.com>
cc: ceph-devel@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 815f80ad20 ]
pwm_num is set to 7 for these chips, but NCT6776_REG_PWM_MODE and
NCT6776_PWM_MODE_MASK only contain 6 values.
Fix this by adding another 0 to the end of each array.
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Link: https://lore.kernel.org/r/20250312030832.106475-1-tasos@tasossah.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edcccc6892 ]
We are no longer depending on legacy device trees so
drop the no compatible check for NAND and OneNAND
nodes.
Suggested-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20250114-omap-gpmc-drop-no-compatible-check-v1-1-262c8d549732@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80b5f90158 ]
In can_send() and can_receive() CAN messages and CAN filter matches are
counted to be visible in the CAN procfs files.
KCSAN detected a data race within can_send() when two CAN frames have
been generated by a timer event writing to the same CAN netdevice at the
same time. Use atomic operations to access the statistics in the hot path
to fix the KCSAN complaint.
Reported-by: syzbot+78ce4489b812515d5e4d@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/67cd717d.050a0220.e1a89.0006.GAE@google.com
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250310143353.3242-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21b02fd9c ]
These scripts fail if the kernel is tainted which leads to wrong test
failure reports in CI environments when an unrelated test triggers some
splat.
Check taint state at start of script and SKIP if its already dodgy.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a70f891e0f ]
When devmem socket is closed, netdev_rx_queue_restart() is called to
reset queue by the net_devmem_unbind_dmabuf(). But callback may return
-ENETDOWN if the interface is down because queues are already freed
when the interface is down so queue reset is not needed.
So, it should not warn if the return value is -ENETDOWN.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250309134219.91670-8-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4afacc9948 ]
When userspace invokes S4 the flow is:
1) amdgpu_pmops_prepare()
2) amdgpu_pmops_freeze()
3) Create hibernation image
4) amdgpu_pmops_thaw()
5) Write out image to disk
6) Turn off system
Then on resume amdgpu_pmops_restore() is called.
This flow has a problem that because amdgpu_pmops_thaw() is called
it will call amdgpu_device_resume() which will resume all of the GPU.
This includes turning the display hardware back on and discovering
connectors again.
This is an unexpected experience for the display to turn back on.
Adjust the flow so that during the S4 sequence display hardware is
not turned back on.
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2038
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Link: https://lore.kernel.org/r/20250306185124.44780-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 68bfdc8dc0)
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f674e7b67 ]
The PCIe error handling has the nvme driver quiesce the device, attempt
to restart it, then wait for that restart to complete.
A PCIe DPC event also toggles the PCIe link. If the slot doesn't have
out-of-band presence detection, this will trigger a pciehp
re-enumeration.
The error handling that calls nvme_error_resume is holding the device
lock while this happens. This lock blocks pciehp's request to disconnect
the driver from proceeding.
Meanwhile the nvme's reset can't make forward progress because its
device isn't there anymore with outstanding IO, and the timeout handler
won't do anything to fix it because the device is undergoing error
handling.
End result: deadlocked.
Fix this by having the timeout handler short cut the disabling for a
disconnected PCIe device. The downside is that we're relying on an IO
timeout to clean up this mess, which could be a minute by default.
Tested-by: Nilay Shroff <nilay@linux.ibm.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65be5c95d0 ]
The kernel requires X86_FEATURE_SGX_LC to be able to create SGX enclaves,
not just X86_FEATURE_SGX.
There is quite a number of hardware which has X86_FEATURE_SGX but not
X86_FEATURE_SGX_LC. A kernel running on such hardware does not create
the /dev/sgx_enclave file and does so silently.
Explicitly warn if X86_FEATURE_SGX_LC is not enabled to properly notify
users that the kernel disabled the SGX driver.
The X86_FEATURE_SGX_LC, a.k.a. SGX Launch Control, is a CPU feature
that enables LE (Launch Enclave) hash MSRs to be writable (with
additional opt-in required in the 'feature control' MSR) when running
enclaves, i.e. using a custom root key rather than the Intel proprietary
key for enclave signing.
I've hit this issue myself and have spent some time researching where
my /dev/sgx_enclave file went on SGX-enabled hardware.
Related links:
https://github.com/intel/linux-sgx/issues/837https://patchwork.kernel.org/project/platform-driver-x86/patch/20180827185507.17087-3-jarkko.sakkinen@linux.intel.com/
[ mingo: Made the error message a bit more verbose, and added other cases
where the kernel fails to create the /dev/sgx_enclave device node. ]
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Kai Huang <kai.huang@intel.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20250309172215.21777-2-vdronov@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09beefefb5 ]
The hypercall in hv_mark_gpa_visibility() is invoked with an input
argument and an output argument. The output argument ostensibly returns
the number of pages that were processed. But in fact, the hypercall does
not provide any output, so the output argument is spurious.
The spurious argument is harmless because Hyper-V ignores it, but in the
interest of correctness and to avoid the potential for future problems,
remove it.
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Link: https://lore.kernel.org/r/20250226200612.2062-2-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250226200612.2062-2-mhklinux@outlook.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
