[ Upstream commit 7f4dbc3f26 ]
Since commit 65ac79e181 ("net: dsa: microchip: add the phylink
get_caps") the phy-mode must be set otherwise the switch driver will
assume "NA" mode and invalidate the port.
Fixes: 65ac79e181 ("net: dsa: microchip: add the phylink get_caps")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fa24aa721 ]
The Verdin iMX8M Mini System on Module does not have USB-ID signal
connected on Verdin USB_2 (usbotg2). On Verdin Development board this is
no problem, as we have connected a USB-Hub that is always connected.
However, if Verdin USB_2 is desired to be used as a single USB-Host port
the chipidea driver does not detect if a USB device is plugged into this
port, due to runtime pm shutting down the PHY.
Add the power-domain &pgc_otg2 to &usbphynop2 in order to detect
plugging events and enumerate the usb device.
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df88005bd8 ]
In case the power domain clock are ungated before the reset is asserted,
the system might freeze completely. This is likely due to a device is an
undefined state being attached to bus, which sporadically leads to a bus
hang. Assert the reset before the clock are enabled to assure the device
is in defined state before being attached to bus.
Fixes: fe58c887fb ("soc: imx: gpcv2: add support for optional resets")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7406f864e ]
The Lynx PCS integrated with ENETC port 0 does not support in-band
autoneg for the 2500base-x SERDES protocol, and prints errors from its
phylink methods. Furthermore, the AQR112 card used for these boards does
not expect in-band autoneg either. So delete the extraneous property.
Fixes: e426d63e75 ("arm64: dts: ls1028a-qds: add overlays for various serdes protocols")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af7d78c957 ]
Drop the "winbond,w25q16dw" compatible since it causes to set the
MODALIAS to w25q16dw which is not specified within spi-nor id table.
Fix this by use the common "jedec,spi-nor" compatible.
Fixes: 2125212785 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83c75e1bc2 ]
This naming error slipped through, so now that a new backlight node has
been added with correct spelling, fix this one also.
Fixes: 98efa526a0 ("ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node")
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56c310de0b ]
ib_dma_map_sg() augments the SGL into a 'dma mapped SGL'. This process
may change the number of entries and the lengths of each entry.
Code that touches dma_address is iterating over the 'dma mapped SGL'
and must use dma_nents which returned from ib_dma_map_sg().
We should use the return count from ib_dma_map_sg for futher usage.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20220818105355.110344-4-haris.iqbal@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Aleksei Marov <aleksei.marov@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b66905e04d ]
When iommu is enabled, we hit warnings like this:
WARNING: at rtrs/rtrs.c:178 rtrs_iu_post_rdma_write_imm+0x9b/0x110
rtrs warn on one sge entry length is 0, which is unexpected.
The problem is ib_dma_map_sg augments the SGL into a 'dma mapped SGL'.
This process may change the number of entries and the lengths of each
entry.
Code that touches dma_address is iterating over the 'dma mapped SGL'
and must use dma_nents which returned from ib_dma_map_sg().
So pass the count return from ib_dma_map_sg.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20220818105355.110344-3-haris.iqbal@ionos.com
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Reviewed-by: Aleksei Marov <aleksei.marov@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eaac78912 ]
This property was never needed, remove it. This also silences
dtbs_check warnings.
Fixes: b186b8b6e7 ("arm64: dts: freescale: add initial device tree for TQMa8Mx with i.MX8M")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5723cfc01 ]
Currently the max_raw_read and max_raw_write limits in regmap_spi struct
do not take into account the additional size of the transmitted register
address and padding. This may result in exceeding the maximum permitted
SPI message size, which could cause undefined behaviour, e.g. data
corruption.
Fix regmap_get_spi_bus() to properly adjust the above mentioned limits
by reserving space for the register address/padding as set in the regmap
configuration.
Fixes: f231ff38b7 ("regmap: spi: Set regmap max raw r/w from max_transfer_size")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220818104851.429479-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e9f130e077 ]
Switch to level interrupt for mcp251xfd. This will make sure no
interrupts are lost.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes: 6a57f224f7 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b64b46fbaa ]
This reverts commit 8239d67f59.
This change confuses the sysfs cleanup path since the rename is done
after the device registration.
Fixes: 8239d67f59 ("soc: imx: imx8m-blk-ctrl: set power device name")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea75deef1a ]
Only report a button state change if the interrupt status shows that
there was a button event.
Previously the code would always drop into the button reporting at the
end of interrupt handling if the jack was present. If neither of the
button report interrupts were pending it would report all buttons
released. This could then lead to a button being reported as released
while it is still pressed.
Fixes: c5b8ee0879 ("ASoC: cs42l42: Report jack and button detection")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220815123138.3810249-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46f7ac3d78 ]
Shifting the recieved bit by "bits" inserts it at the top of the
*currently remaining* Tx data, so we end up accumulating the whole
transfer into bit 0 of the output word. Oops.
For the algorithm to work as intended, we need to remember where the
top of the *original* word was, and shift Rx to there.
Fixes: 1847e3046c ("spi: gpio: Implement LSB First bitbang support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/28324d8622da80461cce35a82859b003d6f6c4b0.1659538737.git.robin.murphy@arm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c919c164fc ]
smb3 fallocate zero range was not grabbing the inode or filemap_invalidate
locks so could have race with pagemap reinstantiating the page.
Cc: stable@vger.kernel.org
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 400d0ad63b ]
SMB2_ioctl() is always called with is_fsctl = true, so doesn't make any
sense to have it at all.
Thus, always set SMB2_0_IOCTL_IS_FSCTL flag on the request.
Also, as per MS-SMB2 3.3.5.15 "Receiving an SMB2 IOCTL Request", servers
must fail the request if the request flags is zero anyway.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Reviewed-by: Tom Talpey <tom@talpey.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f7e723643 ]
Bringing up a CPU may involve creating and destroying tasks which requires
read-locking threadgroup_rwsem, so threadgroup_rwsem nests inside
cpus_read_lock(). However, cpuset's ->attach(), which may be called with
thredagroup_rwsem write-locked, also wants to disable CPU hotplug and
acquires cpus_read_lock(), leading to a deadlock.
Fix it by guaranteeing that ->attach() is always called with CPU hotplug
disabled and removing cpus_read_lock() call from cpuset_attach().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-and-tested-by: Imran Khan <imran.f.khan@oracle.com>
Reported-and-tested-by: Xuewen Yan <xuewen.yan@unisoc.com>
Fixes: 05c7b7a92c ("cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug")
Cc: stable@vger.kernel.org # v5.17+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 671c11f061 ]
cgroup_update_dfl_csses() write-lock the threadgroup_rwsem as updating the
csses can trigger process migrations. However, if the subtree doesn't
contain any tasks, there aren't gonna be any cgroup migrations. This
condition can be trivially detected by testing whether
mgctx.preloaded_src_csets is empty. Elide write-locking threadgroup_rwsem if
the subtree is empty.
After this optimization, the usage pattern of creating a cgroup, enabling
the necessary controllers, and then seeding it with CLONE_INTO_CGROUP and
then removing the cgroup after it becomes empty doesn't need to write-lock
threadgroup_rwsem at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit da6d507f5f upstream.
Add the missing destroy_workqueue() before return from
lpfc_sli4_driver_resource_setup() in the error path.
Link: https://lore.kernel.org/r/20220823044237.285643-1-yangyingliang@huawei.com
Fixes: 3cee98db26 ("scsi: lpfc: Fix crash on driver unload in wq free")
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 991df3dd51 upstream.
Fix the following use-after-free warning which is observed during
controller reset:
refcount_t: underflow; use-after-free.
WARNING: CPU: 23 PID: 5399 at lib/refcount.c:28 refcount_warn_saturate+0xa6/0xf0
Link: https://lore.kernel.org/r/20220906134908.1039-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 672d6ca758 upstream.
A lot of modern laptops use the Parade PS8461E MUX for eDP
switching. The MUX can operate in jitter cleaning mode or
redriver mode, the first one resulting in higher link
quality. The jitter cleaning mode needs to know the link
rate used and the MUX achieves this by snooping the
LINK_BW_SET, LINK_RATE_SELECT and SUPPORTED_LINK_RATES
DPCD accesses.
When the MUX is powered down (seems this can happen whenever
the display is turned off) it loses track of the snooped
link rates so when we do the LINK_RATE_SELECT write it no
longer knowns which link rate we're selecting, and thus it
falls back to the lower quality redriver mode. This results
in unstable high link rates (eg. usually 8.1Gbps link rate
no longer works correctly).
In order to avoid all that let's re-snoop SUPPORTED_LINK_RATES
from the sink at the start of every link training.
Unfortunately we don't have a way to detect the presence of
the MUX. It looks like the set of laptops equipped with this
MUX is fairly large and contains devices from multiple
manufacturers. It may also still be growing with new models.
So a quirk doesn't seem like a very easily maintainable
option, thus we shall attempt to do this unconditionally on
all machines that use LINK_RATE_SELECT. Hopefully this extra
DPCD read doesn't cause issues for any unaffected machine.
If that turns out to be the case we'll need to convert this
into a quirk in the future.
Cc: stable@vger.kernel.org
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6205
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902070319.15395-1-ville.syrjala@linux.intel.com
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 25899c590c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1cab97057 upstream.
We need to inform PCODE of a desired ring frequencies so PCODE update
the memory frequencies to us. rps->min_freq and rps->max_freq are the
frequencies used in that request. However they were unset when SLPC was
enabled and PCODE never updated the memory freq.
v2 (as Suggested by Ashutosh): if SLPC is in use, let's pick the right
frequencies from the get_ia_constants instead of the fake init of
rps' min and max.
v3: don't forget the max <= min return
v4: Move all the freq conversion to intel_rps.c. And the max <= min
check to where it belongs.
v5: (Ashutosh) Fix old comment s/50 HZ/50 MHz and add a doc explaining
the "raw format"
Fixes: 7ba79a6715 ("drm/i915/guc/slpc: Gate Host RPS when SLPC is enabled")
Cc: <stable@vger.kernel.org> # v5.15+
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Tested-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831214538.143950-1-rodrigo.vivi@intel.com
(cherry picked from commit 018a7bdbb0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edca5a2c37 upstream.
Turns out the MIPI sequence block version number and
new block size fields are considered part of the block
header and are not included in the reported new block size
field itself. Bump up the block size appropriately so that
we'll copy over the last five bytes of the block as well.
For this particular machine those last five bytes included
parts of the GPIO op for the backlight on sequence, causing
the backlight no longer to turn back on:
Sequence 6 - MIPI_SEQ_BACKLIGHT_ON
Delay: 20000 us
- GPIO index 0, number 0, set 0 (0x00)
+ GPIO index 1, number 70, set 1 (0x01)
Cc: stable@vger.kernel.org
Fixes: e163cfb4c9 ("drm/i915/bios: Make copies of VBT data blocks")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6652
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220829135834.8585-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit a06289f3f7)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5666a274a6 upstream.
Python likes to send an empty string for some sysfs files, including the
driver_override field. When commit 23d99baf9d ("PCI: Use
driver_set_override() instead of open-coding") moved the PCI core to use
the driver core function instead of hand-rolling their own handler, this
showed up as a regression from some userspace tools, like DPDK.
Fix this up by actually looking at the length of the string first
instead of trusting that userspace got it correct.
Fixes: 23d99baf9d ("PCI: Use driver_set_override() instead of open-coding")
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@kernel.org>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Huisong Li <lihuisong@huawei.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220901163734.3583106-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbfac7fa49 upstream.
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. Fix this up by properly
calling dput().
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: hersen wu <hersenxs.wu@amd.com>
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Thelford Williams <tdwilliamsiv@gmail.com>
Cc: Fangzhi Zuo <Jerry.Zuo@amd.com>
Cc: Yongzhi Liu <lyz_cs@pku.edu.cn>
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Cc: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2e4065965 upstream.
Kuyo reports that the pattern of using debugfs_remove(debugfs_lookup())
leaks a dentry and with a hotplug stress test, the machine eventually
runs out of memory.
Fix this up by using the newly created debugfs_lookup_and_remove() call
instead which properly handles the dentry reference counting logic.
Cc: Major Chen <major.chen@samsung.com>
Cc: stable <stable@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Daniel Bristot de Oliveira <bristot@redhat.com>
Cc: Valentin Schneider <vschneid@redhat.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Reported-by: Kuyo Chang <kuyo.chang@mediatek.com>
Tested-by: Kuyo Chang <kuyo.chang@mediatek.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20220902123107.109274-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dec9b2f1e0 upstream.
There is a very common pattern of using
debugfs_remove(debufs_lookup(..)) which results in a dentry leak of the
dentry that was looked up. Instead of having to open-code the correct
pattern of calling dput() on the dentry, create
debugfs_lookup_and_remove() to handle this pattern automatically and
properly without any memory leaks.
Cc: stable <stable@kernel.org>
Reported-by: Kuyo Chang <kuyo.chang@mediatek.com>
Tested-by: Kuyo Chang <kuyo.chang@mediatek.com>
Link: https://lore.kernel.org/r/YxIaQ8cSinDR881k@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20e0fbab16 upstream.
SBI firmware should report total number of firmware and hardware counters
including unused ones or special ones. In this case the kernel doesn't need
to make any assumptions about gaps in reported counters, e.g. excluded timer
counter. That was fixed in OpenSBI v1.1 by commit 3f66465fb6bf ("lib: pmu:
allow to use the highest available counter"). This kernel patch has no effect
if SBI firmware behaves correctly. However it eliminates access beyond the
allocated pmu_ctr_list if the kernel is used with OpenSBI older than v1.1.
Fixes: e999143459 ("RISC-V: Add perf platform driver based on SBI PMU extension")
Signed-off-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220830155306.301714-2-geomatsi@gmail.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 873aefb376 upstream.
There's currently a reference count leak on the zero page. We increment
the reference via pin_user_pages_remote(), but the page is later handled
as an invalid/reserved page, therefore it's not accounted against the
user and not unpinned by our put_pfn().
Introducing special zero page handling in put_pfn() would resolve the
leak, but without accounting of the zero page, a single user could
still create enough mappings to generate a reference count overflow.
The zero page is always resident, so for our purposes there's no reason
to keep it pinned. Therefore, add a loop to walk pages returned from
pin_user_pages_remote() and unpin any zero pages.
Cc: stable@vger.kernel.org
Reported-by: Luboslav Pivarc <lpivarc@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/166182871735.3518559.8884121293045337358.stgit@omen
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5b81ced74 upstream.
The commit 2ce543f478 ("btrfs: zoned: wait until zone is finished when
allocation didn't progress") implemented a zone finish waiting mechanism
to the write path of zoned mode. However, using
wait_var_event()/wake_up_all() on fs_info->zone_finish_wait is wrong and
wait_var_event() just hangs because no one ever wakes it up once it goes
into sleep.
Instead, we can simply use wait_on_bit_io() and clear_and_wake_up_bit()
on fs_info->flags with a proper barrier installed.
Fixes: 2ce543f478 ("btrfs: zoned: wait until zone is finished when allocation didn't progress")
CC: stable@vger.kernel.org # 5.16+
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cac5c44c48 upstream.
The commit 7d7672bc5d ("btrfs: convert count_max_extents() to use
fs_info->max_extent_size") introduced a division by
fs_info->max_extent_size. This max_extent_size is initialized with max
zone append limit size of the device btrfs runs on. However, in zone
emulation mode, the device is not zoned then its zone append limit is
zero. This resulted in zero value of fs_info->max_extent_size and caused
zero division error.
Fix the error by setting non-zero pseudo value to max append zone limit
in zone emulation mode. Set the pseudo value based on max_segments as
suggested in the commit c2ae7b772e ("btrfs: zoned: revive
max_zone_append_bytes").
Fixes: 7d7672bc5d ("btrfs: convert count_max_extents() to use fs_info->max_extent_size")
CC: stable@vger.kernel.org # 5.12+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cecf8e128e upstream.
Since the check_user_trigger() is called outside of RCU
read lock, this list_for_each_entry_rcu() caused a suspicious
RCU usage warning.
# echo hist:keys=pid > events/sched/sched_stat_runtime/trigger
# cat events/sched/sched_stat_runtime/trigger
[ 43.167032]
[ 43.167418] =============================
[ 43.167992] WARNING: suspicious RCU usage
[ 43.168567] 5.19.0-rc5-00029-g19ebe4651abf #59 Not tainted
[ 43.169283] -----------------------------
[ 43.169863] kernel/trace/trace_events_trigger.c:145 RCU-list traversed in non-reader section!!
...
However, this file->triggers list is safe when it is accessed
under event_mutex is held.
To fix this warning, adds a lockdep_is_held check to the
list_for_each_entry_rcu().
Link: https://lkml.kernel.org/r/166226474977.223837.1992182913048377113.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: 7491e2c442 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54c3931957 upstream.
Currently, The arguments passing to lockdep_hardirqs_{on,off} was fixed
in CALLER_ADDR0.
The function trace_hardirqs_on_caller should have been intended to use
caller_addr to represent the address that caller wants to be traced.
For example, lockdep log in riscv showing the last {enabled,disabled} at
__trace_hardirqs_{on,off} all the time(if called by):
[ 57.853175] hardirqs last enabled at (2519): __trace_hardirqs_on+0xc/0x14
[ 57.853848] hardirqs last disabled at (2520): __trace_hardirqs_off+0xc/0x14
After use trace_hardirqs_xx_caller, we can get more effective information:
[ 53.781428] hardirqs last enabled at (2595): restore_all+0xe/0x66
[ 53.782185] hardirqs last disabled at (2596): ret_from_exception+0xa/0x10
Link: https://lkml.kernel.org/r/20220901104515.135162-2-zouyipeng@huawei.com
Cc: stable@vger.kernel.org
Fixes: c3bc8fd637 ("tracing: Centralize preemptirq tracepoints and unify their usage")
Signed-off-by: Yipeng Zou <zouyipeng@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 47311db8e8 upstream.
Users may have explicitly configured their tracefs permissions; we
shouldn't overwrite those just because a second mount appeared.
Only clobber if the options were provided at mount time.
Note: the previous behavior was especially surprising in the presence of
automounted /sys/kernel/debug/tracing/.
Existing behavior:
## Pre-existing status: tracefs is 0755.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
## (Re)trigger the automount.
# umount /sys/kernel/debug/tracing
# stat -c '%A' /sys/kernel/debug/tracing/.
drwx------
## Unexpected: the automount changed mode for other mount instances.
# stat -c '%A' /sys/kernel/tracing/
drwx------
New behavior (after this change):
## Pre-existing status: tracefs is 0755.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
## (Re)trigger the automount.
# umount /sys/kernel/debug/tracing
# stat -c '%A' /sys/kernel/debug/tracing/.
drwxr-xr-x
## Expected: the automount does not change other mount instances.
# stat -c '%A' /sys/kernel/tracing/
drwxr-xr-x
Link: https://lkml.kernel.org/r/20220826174353.2.Iab6e5ea57963d6deca5311b27fb7226790d44406@changeid
Cc: stable@vger.kernel.org
Fixes: 4282d60689 ("tracefs: Add new tracefs file system")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e53f47f6c1 upstream.
There may be a bad USB audio device with a USB ID of (0x04fa, 0x4201) and
the number of it's interfaces less than 4, an out-of-bounds read bug occurs
when parsing the interface descriptor for this device.
Fix this by checking the number of interfaces.
Signed-off-by: Dongxiang Ke <kdx.glider@gmail.com>
Link: https://lore.kernel.org/r/20220906024928.10951-1-kdx.glider@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 809f44a0cc upstream.
The recent commit c11117b634 ("ALSA: usb-audio: Refcount multiple
accesses on the single clock") tries to manage the clock rate shared
by several endpoints. This was intended for avoiding the unmatched
rate by a different endpoint, but unfortunately, it introduced a
regression for PulseAudio and pipewire, too; those applications try to
probe the multiple possible rates (44.1k and 48kHz) and setting up the
normal rate fails but only the last rate is applied.
The cause is that the last sample rate is still left to the clock
reference even after closing the endpoint, and this value is still
used at the next open. It happens only when applications set up via
PCM prepare but don't start/stop the stream; the rate is reset when
the stream is stopped, but it's not cleared at close.
This patch addresses the issue above, simply by clearing the rate set
in the clock reference at the last close of each endpoint.
Fixes: c11117b634 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/YxXIWv8dYmg1tnXP@zx2c4.com/
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/2620
Link: https://lore.kernel.org/r/20220907100421.6443-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff878b408a upstream.
One of the former changes for the endpoint management was the more
consistent setup of endpoints at hw_params.
snd_usb_endpoint_configure() is a single function that does the full
setup, and it's called from both PCM hw_params and prepare callbacks.
Although the EP setup at the prepare phase is usually skipped (by
checking need_setup flag), it may be still effective in some cases
like suspend/resume that requires the interface setup again.
As it's a full and single setup, the invocation of
snd_usb_endpoint_configure() includes not only the USB interface setup
but also the buffer release and allocation. OTOH, doing the buffer
release and re-allocation at PCM prepare phase is rather superfluous,
and better to be done only in the hw_params phase.
For those optimizations, this patch splits the endpoint setup to two
phases: snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare(),
to be called from hw_params and from prepare, respectively.
Note that this patch changes the driver operation slightly,
effectively moving the USB interface setup again to PCM prepare stage
instead of hw_params stage, while the buffer allocation and such
initializations are still done at hw_params stage.
And, the change of the USB interface setup timing (moving to prepare)
gave an interesting "fix", too: it was reported that the recent
kernels caused silent output at the beginning on playbacks on some
devices on Android, and this change casually fixed the regression.
It seems that those devices are picky about the sample rate change (or
the interface change?), and don't follow the too immediate rate
changes.
Meanwhile, Android operates the PCM in the following order:
- open, then hw_params with the possibly highest sample rate
- close without prepare
- re-open, hw_params with the normal sample rate
- prepare, and start streaming
This procedure ended up the hw_params twice with different rates, and
because the recent kernel did set up the sample rate twice one and
after, it screwed up the device. OTOH, the earlier kernels didn't set
up the USB interface at hw_params, hence this problem didn't appear.
Now, with this patch, the USB interface setup is again back to the
prepare phase, and it works around the problem automagically.
Although we should address the sample rate problem in a more solid
way in future, let's keep things working as before for now.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
Reported-by: chihhao chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/87e6d6ae69d68dc588ac9acc8c0f24d6188375c3.camel@mediatek.com
Link: https://lore.kernel.org/r/20220901124136.4984-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e48940abe upstream.
In loopback_jiffies_timer_pos_update(), we are getting jiffies twice.
First time for playback, second time for capture. Jiffies can be updated
between these two calls and if the capture jiffies is larger, extra zeros
will be filled in the capture buffer.
Change to get jiffies once and use it for both playback and capture.
Signed-off-by: Pattara Teerapong <pteerapong@chromium.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220901144036.4049060-1-pteerapong@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37137ec26c upstream.
The last fix for trying to recover the regression on AMD platforms,
unfortunately, leaded to yet another regression: it turned out that
IOMMUs don't like the usage of raw page allocations.
This is yet another attempt for addressing the log saga; at this time,
we re-use the existing buffer allocation mechanism with SG-pages
although we require only single pages. The SG buffer allocation
itself was confirmed to work for stream buffers, so it's relatively
easy to adapt for other places.
The only problem is: although the HD-audio code is accessing the
address directly via dmab->address field, SG-pages don't set up it.
For the ease of adaption, we now set up the dmab->addr field from the
address of the first page as default, so that it can run with the
HD-audio driver code as-is without the excessive call of
snd_sgbuf_get_addr() multiple times; that's the only change in the
memalloc helper side. The rest is nothing but a flip of the dma_type
field in the HD-audio side.
Fixes: a8d302a0b7 ("ALSA: memalloc: Revive x86-specific WC page allocations again")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CABXGCsO+kB2t5QyHY-rUe76npr1m0-5JOtt8g8SiHUo34ur7Ww@mail.gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216112
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216363
Link: https://lore.kernel.org/r/20220906090319.23358-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d29f59051d upstream.
The voice allocator sometimes begins allocating from near the end of the
array and then wraps around, however snd_emu10k1_pcm_channel_alloc()
accesses the newly allocated voices as if it never wrapped around.
This results in out of bounds access if the first voice has a high enough
index so that first_voice + requested_voice_count > NUM_G (64).
The more voices are requested, the more likely it is for this to occur.
This was initially discovered using PipeWire, however it can be reproduced
by calling aplay multiple times with 16 channels:
aplay -r 48000 -D plughw:CARD=Live,DEV=3 -c 16 /dev/zero
UBSAN: array-index-out-of-bounds in sound/pci/emu10k1/emupcm.c:127:40
index 65 is out of range for type 'snd_emu10k1_voice [64]'
CPU: 1 PID: 31977 Comm: aplay Tainted: G W IOE 6.0.0-rc2-emu10k1+ #7
Hardware name: ASUSTEK COMPUTER INC P5W DH Deluxe/P5W DH Deluxe, BIOS 3002 07/22/2010
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x3f
__ubsan_handle_out_of_bounds.cold+0x44/0x49
snd_emu10k1_playback_hw_params+0x3bc/0x420 [snd_emu10k1]
snd_pcm_hw_params+0x29f/0x600 [snd_pcm]
snd_pcm_common_ioctl+0x188/0x1410 [snd_pcm]
? exit_to_user_mode_prepare+0x35/0x170
? do_syscall_64+0x69/0x90
? syscall_exit_to_user_mode+0x26/0x50
? do_syscall_64+0x69/0x90
? exit_to_user_mode_prepare+0x35/0x170
snd_pcm_ioctl+0x27/0x40 [snd_pcm]
__x64_sys_ioctl+0x95/0xd0
do_syscall_64+0x5c/0x90
? do_syscall_64+0x69/0x90
? do_syscall_64+0x69/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/3707dcab-320a-62ff-63c0-73fc201ef756@tasossah.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8423f0b6d5 upstream.
There is a small race window at snd_pcm_oss_sync() that is called from
OSS PCM SNDCTL_DSP_SYNC ioctl; namely the function calls
snd_pcm_oss_make_ready() at first, then takes the params_lock mutex
for the rest. When the stream is set up again by another thread
between them, it leads to inconsistency, and may result in unexpected
results such as NULL dereference of OSS buffer as a fuzzer spotted
recently.
The fix is simply to cover snd_pcm_oss_make_ready() call into the same
params_lock mutex with snd_pcm_oss_make_ready_locked() variant.
Reported-and-tested-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAFcO6XN7JDM4xSXGhtusQfS2mSBcx50VJKwQpCq=WeLt57aaZA@mail.gmail.com
Link: https://lore.kernel.org/r/20220905060714.22549-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b8983d4252 ]
The mmVM_L2_CNTL3 register is not assigned an initial value
Signed-off-by: Qu Huang <jinsdb@126.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00047c3d96 ]
For some ASICs, like GFX IP v11.0.1, only have one SDMA instance,
so not need to configure SDMA1_RLC_CGCG_CTRL for this case.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
