[ Upstream commit b1dec4e785 ]
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC. Public users only have ES2 onwards.
In addition to the ES1 specific removals, a check for it was added
preventing the machine to boot further. It may otherwise inherit wrong
clock settings from ES2 which could damage the hardware.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230202092332.2504-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b505063910 ]
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230202141919.2298821-1-gregkh@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5746ca131e ]
Interrupt handlers called by soft-pending irq replay code can run
softirqs, softirq replay enables and disables local irqs, which allows
interrupts to come in including soft-masked interrupts, and it can
cause pending irqs to be replayed again. That makes the soft irq replay
state machine and possible races more complicated and fragile than it
needs to be.
Use irq_enter/irq_exit around irq replay to prevent softirqs running
while interrupts are being replayed. Softirqs will now be run at the
irq_exit() call after all the irq replaying is done. This prevents irqs
being replayed while irqs are being replayed, and should hopefully make
things simpler and easier to think about and debug.
A new PACA_IRQ_REPLAYING is added to prevent asynchronous interrupt
handlers hard-enabling EE while pending irqs are being replayed, because
that causes new pending irqs to arrive which is also a complexity. This
means pending irqs won't be profiled quite so well because perf irqs
can't be taken.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230121102618.2824429-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 109d587a4b ]
arch/mips/include/asm/mach-rc32434/pci.h:377:
cc1: error: result of ‘-117440512 << 16’ requires 44 bits to represent, but ‘int’ only has 32 bits [-Werror=shift-overflow=]
All bits in KORINA_STAT are already at the correct position, so there is
no addtional shift needed.
Signed-off-by: xurui <xurui@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03e1d60e17 ]
The watch_queue_set_size() allocation error paths return the ret value
set via the prior pipe_resize_ring() call, which will always be zero.
As a result, IOC_WATCH_QUEUE_SET_SIZE callers such as "keyctl watch"
fail to detect kernel wqueue->notes allocation failures and proceed to
KEYCTL_WATCH_KEY, with any notifications subsequently lost.
Fixes: c73be61ced ("pipe: Add general notification queue support")
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ce2ea07c5 ]
Added the video capability query support for VCN version 4_0_4
Signed-off-by: Veerabadhran Gopalakrishnan <veerabadhran.gopalakrishnan@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6de636eb0 ]
Only VCN0 supports AV1.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 6ce2ea07c5 ("drm/amdgpu/soc21: Add video cap query support for VCN_4_0_4")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20534dbcc7 ]
This patch fixes a return value check in kfd doorbell handling.
This function should return 0(error) only when the ida_simple_get
returns < 0(error), return > 0 is a success case.
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Fixes: 16f0013157 ("drm/amdkfd: Allocate doorbells only when needed")
Acked-by: Christian Koenig <chriatian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a8db5ec4a ]
We're currently using stop_machine() to update ftrace & kprobes, which
means that the thread that takes text_mutex during may not be the same
as the thread that eventually patches the code. This isn't actually a
race because the lock is still held (preventing any other concurrent
accesses) and there is only one thread running during stop_machine(),
but it does trigger a lockdep failure.
This patch just elides the lockdep check during stop_machine.
Fixes: c15ac4fd60 ("riscv/ftrace: Add dynamic function tracer support")
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230303143754.4005217-1-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 647dd2c3f0 ]
Let's revert commit 12724ba389 ("erofs: fix kvcalloc() misuse with
__GFP_NOFAIL") since kvmalloc() already supports __GFP_NOFAIL in commit
a421ef3030 ("mm: allow !GFP_KERNEL allocations for kvmalloc"). So
the original fix was wrong.
Actually there was some issue as [1] discussed, so before that mm fix
is landed, the warn could still happen but applying this commit first
will cause less.
[1] https://lore.kernel.org/r/20230305053035.1911-1-hsiangkao@linux.alibaba.com
Fixes: 12724ba389 ("erofs: fix kvcalloc() misuse with __GFP_NOFAIL")
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230309053148.9223-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8b8a3c601 ]
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ca6705d9d ]
Fix a race where kthread_stop() may prevent the threadfn from ever getting
called. If that happens the svc_rqst will not be cleaned up.
Fixes: ed6473ddc7 ("NFSv4: Fix callback server shutdown")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9dd2e5c6 ]
NDC caches contexts of frequently used queue's (Rx and Tx queues)
contexts. Due to a HW errata when NDC detects fault/poision while
accessing contexts it could go into an illegal state where a cache
line could get locked forever. To makesure all cache lines in NDC
are available for optimum performance upon fault/lockerror/posion
errors scan through all cache lines in NDC and clear the lock bit.
Fixes: 4a3581cd59 ("octeontx2-af: NPA AQ instruction enqueue support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce7ca79471 ]
Before determining whether the msg has unsupported options, it has been
prematurely terminated by the wrong status check.
For the application, the general usages of MSG_FASTOPEN likes
fd = socket(...)
/* rather than connect */
sendto(fd, data, len, MSG_FASTOPEN)
Hence, We need to check the flag before state check, because the sock
state here is always SMC_INIT when applications tries MSG_FASTOPEN.
Once we found unsupported options, fallback it to TCP.
Fixes: ee9dfbef02 ("net/smc: handle sockopts forcing fallback")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
v2 -> v1: Optimize code style
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f5c5a790e ]
With older compilers like gcc-9, the calculation of the vlan
priority field causes a false-positive warning from the byteswap:
In file included from drivers/net/ethernet/intel/ice/ice_tc_lib.c:4:
drivers/net/ethernet/intel/ice/ice_tc_lib.c: In function 'ice_parse_cls_flower':
include/uapi/linux/swab.h:15:15: error: integer overflow in expression '(int)(short unsigned int)((int)match.key-><U67c8>.<U6698>.vlan_priority << 13) & 57344 & 255' of type 'int' results in '0' [-Werror=overflow]
15 | (((__u16)(x) & (__u16)0x00ffU) << 8) | \
| ~~~~~~~~~~~~^~~~~~~~~~~~~~~~~
include/uapi/linux/swab.h:106:2: note: in expansion of macro '___constant_swab16'
106 | ___constant_swab16(x) : \
| ^~~~~~~~~~~~~~~~~~
include/uapi/linux/byteorder/little_endian.h:42:43: note: in expansion of macro '__swab16'
42 | #define __cpu_to_be16(x) ((__force __be16)__swab16((x)))
| ^~~~~~~~
include/linux/byteorder/generic.h:96:21: note: in expansion of macro '__cpu_to_be16'
96 | #define cpu_to_be16 __cpu_to_be16
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/ice/ice_tc_lib.c:1458:5: note: in expansion of macro 'cpu_to_be16'
1458 | cpu_to_be16((match.key->vlan_priority <<
| ^~~~~~~~~~~
After a change to be16_encode_bits(), the code becomes more
readable to both people and compilers, which avoids the warning.
Fixes: 34800178b3 ("ice: Add support for VLAN priority filters in switchdev")
Suggested-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef3f92e8a ]
When creating the TLV to send to the FW for configuring DSCP mode PFC,the
PFCENABLE field was being masked with a 4 bit mask (0xF), but this is an 8
bit bitmask for enabled classes for PFC. This means that traffic classes
4-7 could not be enabled for PFC.
Remove the mask completely, as it is not necessary, as we are assigning 8
bits to an 8 bit field.
Fixes: 2a87bd73e5 ("ice: Add DSCP support")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd9a2e1d51 ]
Flole observes this WARNING on occasion:
[1210423.486503] WARNING: CPU: 8 PID: 1524732 at fs/ext4/ext4_jbd2.c:75 ext4_journal_check_start+0x68/0xb0
Reported-by: <flole@flole.de>
Suggested-by: Jan Kara <jack@suse.cz>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217123
Fixes: 73da852e38 ("nfsd: use vfs_iter_read/write")
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428913bce1 ]
If disk_scan_partitions() is called with 'FMODE_EXCL',
blkdev_get_by_dev() will be called without 'FMODE_EXCL', however, follow
blkdev_put() is still called with 'FMODE_EXCL', which will cause
'bd_holders' counter to leak.
Fix the problem by using the right mode for blkdev_put().
Reported-by: syzbot+2bcc0d79e548c4f62a59@syzkaller.appspotmail.com
Link: https://lore.kernel.org/lkml/f9649d501bc8c3444769418f6c26263555d9d3be.camel@linux.ibm.com/T/
Tested-by: Julian Ruess <julianr@linux.ibm.com>
Fixes: e5cfefa97b ("block: fix scan partition for exclusively open device again")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e7e1541c9 ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: ef0f62264b ("platform/x86: mlx-platform: Add physical bus number auto detection")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vadim Pasternak <vadimp@mellanox.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: platform-driver-x86@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-7-rdunlap@infradead.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03f5eb300a ]
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
For NVSW_SN2201, select REGMAP_I2C instead of depending on it.
Fixes: c6acad68eb ("platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface")
Fixes: 5ec4a8ace0 ("platform/mellanox: Introduce support for Mellanox register access driver")
Fixes: 62f9529b8d ("platform/mellanox: mlxreg-lc: Add initial support for Nvidia line card devices")
Fixes: 662f24826f ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Michael Shych <michaelsh@nvidia.com>
Cc: Mark Gross <markgross@kernel.org>
Cc: Vadim Pasternak <vadimp@nvidia.com>
Cc: platform-driver-x86@vger.kernel.org
Link: https://lore.kernel.org/r/20230226053953.4681-6-rdunlap@infradead.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0331b1b0ba ]
After using the built-in UEFI hardware diagnostics to compare
the measured battery temperature, i noticed that the temperature
is actually expressed in tenth degree kelvin, similar to the
SBS-Data standard. For example, a value of 2992 is displayed as
26 degrees celsius.
Fix the scaling so that the correct values are being displayed.
Tested on a Dell Inspiron 3505.
Fixes: a77272c160 ("platform/x86: dell: Add new dell-wmi-ddv driver")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230218115318.20662-2-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36d44825fa ]
In several cases, the DDV WMI interface can return buffers
with a length of zero. Return -ENODATA in such a case for
proper error handling. Also replace some -EIO errors with
more specialized ones.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230126194021.381092-3-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: 0331b1b0ba ("platform/x86: dell-ddv: Fix temperature scaling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c77737b736 ]
Customers using GKE 1.25 and 1.26 are facing conntrack issues
root caused to commit c9c3b6811f ("netfilter: conntrack: make
max chain length random").
Even if we assume Uniform Hashing, a bucket often reachs 8 chained
items while the load factor of the hash table is smaller than 0.5
With a limit of 16, we reach load factors of 3.
With a limit of 32, we reach load factors of 11.
With a limit of 40, we reach load factors of 15.
With a limit of 50, we reach load factors of 24.
This patch changes MIN_CHAINLEN to 50, to minimize risks.
Ideally, we could in the future add a cushion based on expected
load factor (2 * nf_conntrack_max / nf_conntrack_buckets),
because some setups might expect unusual values.
Fixes: c9c3b6811f ("netfilter: conntrack: make max chain length random")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 288b3271d9 ]
When the sd driver revalidates host-managed SMR disks, it calls
disk_set_zoned() which changes the zone_write_granularity attribute value
to the logical block size regardless of the device type. After that, the sd
driver overwrites the value in sd_zbc_read_zone() with the physical block
size, since ZBC/ZAC requires this for host-managed disks. Between the calls
to disk_set_zoned() and sd_zbc_read_zone(), there exists a window where the
attribute shows the logical block size as the zone_write_granularity value,
which is wrong for host-managed disks. The duration of the window is from
20ms to 200ms, depending on report zone command execution time.
To avoid the wrong zone_write_granularity value between disk_set_zoned()
and sd_zbc_read_zone(), modify the value not in sd_zbc_read_zone() but
just after disk_set_zoned() call.
Fixes: a805a4fa4f ("block: introduce zone_write_granularity limit")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230306063024.3376959-1-shinichiro.kawasaki@wdc.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfa659177d ]
The firmware only supports Logical Disk IDs up to 240 and LD ID 255 (0xFF)
is reserved for deleted LDs. However, in some cases, firmware was assigning
LD ID 254 (0xFE) to deleted LDs and this was causing the driver to mark the
wrong disk as deleted. This in turn caused the wrong disk device to be
taken offline by the SCSI midlayer.
To address this issue, limit the LD ID range from 255 to 240. This ensures
the deleted LD ID is properly identified and removed by the driver without
accidently deleting any valid LDs.
Fixes: ae6874ba4b ("scsi: megaraid_sas: Early detection of VD deletion through RaidMap update")
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20230302105342.34933-2-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e539a105f9 ]
Adrien reports that incorrect data is transmitted when a single
page straddles multiple records. We would transmit the same
data in all iterations of the loop.
Reported-by: Adrien Moulin <amoulin@corp.free.fr>
Link: https://lore.kernel.org/all/61481278.42813558.1677845235112.JavaMail.zimbra@corp.free.fr
Fixes: c1318b39c7 ("tls: Add opt-in zerocopy mode of sendfile()")
Tested-by: Adrien Moulin <amoulin@corp.free.fr>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Acked-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Link: https://lore.kernel.org/r/20230304192610.3818098-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 193250ace2 ]
Fix data corruption issue with SerDes connected PHYs operating at 1.25
Gbps speed where we could previously observe about 30% packet loss while
the bad packet counter was increasing.
As almost all boards with MediaTek MT7622 or MT7986 use either the MT7531
switch IC operating at 3.125Gbps SerDes rate or single-port PHYs using
rate-adaptation to 2500Base-X mode, this issue only got exposed now when
we started trying to use SFP modules operating with 1.25 Gbps with the
BananaPi R3 board.
The fix is to set bit 12 which disables the RX FIFO clear function when
setting up MAC MCR, MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are
corrupted by GMAC."[1]
[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/d8a2975939a12686c4a95c40db21efdc3f821f63
Fixes: 42c03844e9 ("net-next: mediatek: add support for MediaTek MT7622 SoC")
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/138da2735f92c8b6f8578ec2e5a794ee515b665f.1677937317.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58aac3a2ef ]
Currently link up can't be detected in forced mode if polling
isn't used. Only link up interrupt source we have is aneg
complete which isn't applicable in forced mode. Therefore we
have to use energy-on as link up indicator.
Fixes: 7365494550 ("net: phy: smsc: skip ENERGYON interrupt if disabled")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b459804ff ]
btf_datasec_resolve contains a bug that causes the following BTF
to fail loading:
[1] DATASEC a size=2 vlen=2
type_id=4 offset=0 size=1
type_id=7 offset=1 size=1
[2] INT (anon) size=1 bits_offset=0 nr_bits=8 encoding=(none)
[3] PTR (anon) type_id=2
[4] VAR a type_id=3 linkage=0
[5] INT (anon) size=1 bits_offset=0 nr_bits=8 encoding=(none)
[6] TYPEDEF td type_id=5
[7] VAR b type_id=6 linkage=0
This error message is printed during btf_check_all_types:
[1] DATASEC a size=2 vlen=2
type_id=7 offset=1 size=1 Invalid type
By tracing btf_*_resolve we can pinpoint the problem:
btf_datasec_resolve(depth: 1, type_id: 1, mode: RESOLVE_TBD) = 0
btf_var_resolve(depth: 2, type_id: 4, mode: RESOLVE_TBD) = 0
btf_ptr_resolve(depth: 3, type_id: 3, mode: RESOLVE_PTR) = 0
btf_var_resolve(depth: 2, type_id: 4, mode: RESOLVE_PTR) = 0
btf_datasec_resolve(depth: 1, type_id: 1, mode: RESOLVE_PTR) = -22
The last invocation of btf_datasec_resolve should invoke btf_var_resolve
by means of env_stack_push, instead it returns EINVAL. The reason is that
env_stack_push is never executed for the second VAR.
if (!env_type_is_resolve_sink(env, var_type) &&
!env_type_is_resolved(env, var_type_id)) {
env_stack_set_next_member(env, i + 1);
return env_stack_push(env, var_type, var_type_id);
}
env_type_is_resolve_sink() changes its behaviour based on resolve_mode.
For RESOLVE_PTR, we can simplify the if condition to the following:
(btf_type_is_modifier() || btf_type_is_ptr) && !env_type_is_resolved()
Since we're dealing with a VAR the clause evaluates to false. This is
not sufficient to trigger the bug however. The log output and EINVAL
are only generated if btf_type_id_size() fails.
if (!btf_type_id_size(btf, &type_id, &type_size)) {
btf_verifier_log_vsi(env, v->t, vsi, "Invalid type");
return -EINVAL;
}
Most types are sized, so for example a VAR referring to an INT is not a
problem. The bug is only triggered if a VAR points at a modifier. Since
we skipped btf_var_resolve that modifier was also never resolved, which
means that btf_resolved_type_id returns 0 aka VOID for the modifier.
This in turn causes btf_type_id_size to return NULL, triggering EINVAL.
To summarise, the following conditions are necessary:
- VAR pointing at PTR, STRUCT, UNION or ARRAY
- Followed by a VAR pointing at TYPEDEF, VOLATILE, CONST, RESTRICT or
TYPE_TAG
The fix is to reset resolve_mode to RESOLVE_TBD before attempting to
resolve a VAR from a DATASEC.
Fixes: 1dc9285184 ("bpf: kernel side support for BTF Var and DataSec")
Signed-off-by: Lorenz Bauer <lmb@isovalent.com>
Link: https://lore.kernel.org/r/20230306112138.155352-2-lmb@isovalent.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c20822fad ]
&xdp_buff and &xdp_frame are bound in a way that
xdp_buff->data_hard_start == xdp_frame
It's always the case and e.g. xdp_convert_buff_to_frame() relies on
this.
IOW, the following:
for (u32 i = 0; i < 0xdead; i++) {
xdpf = xdp_convert_buff_to_frame(&xdp);
xdp_convert_frame_to_buff(xdpf, &xdp);
}
shouldn't ever modify @xdpf's contents or the pointer itself.
However, "live packet" code wrongly treats &xdp_frame as part of its
context placed *before* the data_hard_start. With such flow,
data_hard_start is sizeof(*xdpf) off to the right and no longer points
to the XDP frame.
Instead of replacing `sizeof(ctx)` with `offsetof(ctx, xdpf)` in several
places and praying that there are no more miscalcs left somewhere in the
code, unionize ::frm with ::data in a flex array, so that both starts
pointing to the actual data_hard_start and the XDP frame actually starts
being a part of it, i.e. a part of the headroom, not the context.
A nice side effect is that the maximum frame size for this mode gets
increased by 40 bytes, as xdp_buff::frame_sz includes everything from
data_hard_start (-> includes xdpf already) to the end of XDP/skb shared
info.
Also update %MAX_PKT_SIZE accordingly in the selftests code. Leave it
hardcoded for 64 bit && 4k pages, it can be made more flexible later on.
Minor: align `&head->data` with how `head->frm` is assigned for
consistency.
Minor #2: rename 'frm' to 'frame' in &xdp_page_head while at it for
clarity.
(was found while testing XDP traffic generator on ice, which calls
xdp_convert_frame_to_buff() for each XDP frame)
Fixes: b530e9e106 ("bpf: Add "live packet" mode for XDP in BPF_PROG_RUN")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230215185440.4126672-1-aleksander.lobakin@intel.com
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4cc1483f3 ]
At btrfs_drop_extent_map_range() we are clearing the EXTENT_FLAG_LOGGING
bit on a 'flags' variable that was not initialized. This makes static
checkers complain about it, so initialize the 'flags' variable before
clearing the bit.
In practice this has no consequences, because EXTENT_FLAG_LOGGING should
not be set when btrfs_drop_extent_map_range() is called, as an fsync locks
the inode in exclusive mode, locks the inode's mmap semaphore in exclusive
mode too and it always flushes all delalloc.
Also add a comment about why we clear EXTENT_FLAG_LOGGING on a copy of the
flags of the split extent map.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/Y%2FyipSVozUDEZKow@kili/
Fixes: db21370bff ("btrfs: drop extent map range more efficiently")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4b97925e8 ]
When booting with an initial ramdisk on platforms where physical memory
does not start at address zero (e.g. on Amiga):
initrd: 0ef0602c - 0f800000
Zone ranges:
DMA [mem 0x0000000008000000-0x000000f7ffffffff]
Normal empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000008000000-0x000000000f7fffff]
Initmem setup node 0 [mem 0x0000000008000000-0x000000000f7fffff]
Unable to handle kernel access at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<00201d3c>] memcmp+0x28/0x56
As phys_to_virt() relies on m68k_memoffset and module_fixup(), it must
not be called before paging_init(). Hence postpone the phys_to_virt
handling for the initial ramdisk until after calling paging_init().
While at it, reduce #ifdef clutter by using IS_ENABLED() instead.
Fixes: 376e3fdecb ("m68k: Enable memtest functionality")
Reported-by: Stephen Walsh <vk3heg@vk3heg.net>
Link: https://lists.debian.org/debian-68k/2022/09/msg00007.html
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/4f45f05f377bf3f5baf88dbd5c3c8aeac59d94f0.camel@physik.fu-berlin.de
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Link: https://lore.kernel.org/r/dff216da09ab7a60217c3fc2147e671ae07d636f.1677528627.git.geert@linux-m68k.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a02426787 ]
The xtables packet traverser performs an unconditional local_bh_disable(),
but the nf_tables evaluation loop does not.
Functions that are called from either xtables or nftables must assume
that they can be called in process context.
inet_twsk_deschedule_put() assumes that no softirq interrupt can occur.
If tproxy is used from nf_tables its possible that we'll deadlock
trying to aquire a lock already held in process context.
Add a small helper that takes care of this and use it.
Link: https://lore.kernel.org/netfilter-devel/401bd6ed-314a-a196-1cdc-e13c720cc8f2@balasys.hu/
Fixes: 4ed8eb6570 ("netfilter: nf_tables: Add native tproxy support")
Reported-and-tested-by: Major Dávid <major.david@balasys.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f7dd42f0d ]
It seems that change was unintentional, we have userspace code that
needs the mark while listening for events like REPLY, DESTROY, etc.
Also include 0-marks in requested dumps, as they were before that fix.
Fixes: 1feeae0715 ("netfilter: ctnetlink: fix compilation warning after data race fixes in ct mark")
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit accd7e2369 ]
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba3 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9334b702a ]
When MAC is not support PMT, driver will check PHY's WoL capability
and set device wakeup capability in stmmac_init_phy(). We can enable
the WoL through ethtool, the driver would enable the device wake up
flag. Now the device_may_wakeup() return true.
But if there is a way which enable the PHY's WoL capability derectly,
like in BIOS. The driver would not know the enable thing and would not
set the device wake up flag. The phy_suspend may failed like this:
[ 32.409063] PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x50 returns -16
[ 32.409065] PM: Device stmmac-1:00 failed to suspend: error -16
[ 32.409067] PM: Some devices failed to suspend, or early wake event detected
Add to set the device wakeup enable flag according to the get_wol
function result in PHY can fix the error in this scene.
v2: add a Fixes tag.
Fixes: 1d8e5b0f3f ("net: stmmac: Support WOL with phy")
Signed-off-by: Rongguang Wei <weirongguang@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce68153edb ]
At sc7280, pingpong block is used to management the dither effects
to reduce distortion at panel. Currently pingpong-0 base offset is
wrongly set at 0x59000. This mistake will not cause system to crash.
However it will make dither not work. This patch correct sc7280 ping
pong-0 block base offset.
Changes in v2:
-- add more details info n regrading of pingpong block at commit text
Fixes: 591e34a091 ("drm/msm/disp/dpu1: add support for display for SC7280 target")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524332/
Link: https://lore.kernel.org/r/1677533800-3125-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0abb6a24aa ]
DMA2 and DMA3 planes on msm8998 should use corresponding DMA2 and DMA3
clocks rather than CURSOR0/1 clocks (which are used for the CURSOR
planes). Correct corresponding SSPP declarations.
Fixes: 94391a14fc ("drm/msm/dpu1: Add MSM8998 to hw catalog")
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Cc: Jami Kettunen <jami.kettunen@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/522230/
Link: https://lore.kernel.org/r/20230211231259.1308718-13-dmitry.baryshkov@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5045b00a6 ]
The msm8998 doesn't seem to support DIM_LAYER, so drop it from
the supported features mask.
Fixes: 2d8a4edb67 ("drm/msm/dpu: use feature bit for LM combined alpha check")
Fixes: 94391a14fc ("drm/msm/dpu1: Add MSM8998 to hw catalog")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/522231/
Link: https://lore.kernel.org/r/20230211231259.1308718-12-dmitry.baryshkov@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03c0c3cb22 ]
QSEED4 is a newer variant of QSEED3LITE, which should be used on
sm8250 and sm8350. Fix the DPU caps structure and used feature masks.
Fixes: d21fc5dfc3 ("drm/msm/dpu1: add support for qseed3lite used on sm8250")
Fixes: 0e91bcbb00 ("drm/msm/dpu: Add SM8350 to hw catalog")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/522229/
Link: https://lore.kernel.org/r/20230211231259.1308718-10-dmitry.baryshkov@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da06be8b4f ]
According to vendor DTS files both sm6115 and qcm2290 should have
max_mixer_width set to 2048 (DEFAULT_DPU_LINE_WIDTH). Correct it.
Fixes: 3581b7062c ("drm/msm/disp/dpu1: add support for display on SM6115")
Fixes: 5334087ee7 ("drm/msm: add support for QCM2290 MDSS")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/522212/
Link: https://lore.kernel.org/r/20230211231259.1308718-6-dmitry.baryshkov@linaro.org
[quic_abhinavk@quicinc.com: fix minor typo in commit message]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
