A malicious connected siw peer can send an iWARP FPDU whose MPA length
field (c_hdr->mpa_len, 16 bit big-endian, peer-controlled) is smaller
than the fixed DDP/RDMAP header for the announced opcode. Soft-iWARP
parses the full header in siw_get_hdr() based on iwarp_pktinfo[opcode]
.hdr_len, but never compares mpa_len against that header length.
siw_tcp_rx_data() then derives
srx->fpdu_part_rem = be16_to_cpu(mpa_len) - fpdu_part_rcvd
+ MPA_HDR_SIZE;
where fpdu_part_rcvd equals iwarp_pktinfo[opcode].hdr_len at this
point. For a tagged WRITE (hdr_len 16, MPA_HDR_SIZE 2) the smallest
on-wire mpa_len of 0 yields fpdu_part_rem = -14, and any mpa_len below
hdr_len - MPA_HDR_SIZE underflows to a negative int.
The signed value then flows into siw_proc_write()/siw_proc_rresp() as
bytes = min(srx->fpdu_part_rem, srx->skb_new);
is handed to siw_check_mem() as an int len (whose interval check
addr + len > mem->va + mem->len is satisfied for a valid base when
len is negative), and reaches siw_rx_data() -> siw_rx_kva() /
siw_rx_umem() -> skb_copy_bits() as a signed copy length. The header
copy branch in skb_copy_bits() promotes that to size_t, producing a
multi-gigabyte read.
KASAN under a KUnit harness that drives the real kernel TCP receive
path -- a loopback AF_INET socketpair, the malformed FPDU written via
kernel_sendmsg, sk_data_ready firing in softirq, tcp_read_sock
dispatching to siw_tcp_rx_data -- reports:
BUG: KASAN: use-after-free in skb_copy_bits+0x284/0x480
Read of size 4294967295 at addr ffff888...
Call Trace:
skb_copy_bits
siw_rx_kva
siw_rx_data
siw_check_mem
siw_proc_write
siw_tcp_rx_data
__tcp_read_sock
siw_qp_llp_data_ready
tcp_data_ready
tcp_data_queue
Add the missing invariant at the earliest point where the peer header
is fully assembled. iwarp_pktinfo[*].hdr_len - MPA_HDR_SIZE is exactly
the value the siw transmitter uses as the minimum mpa_len for each
opcode (drivers/infiniband/sw/siw/siw_qp.c:33), so this matches the
protocol contract. Out-of-range FPDUs terminate the connection with
TERM_ERROR_LAYER_LLP / LLP_ETYPE_MPA / LLP_ECODE_FPDU_START -- which
is RFC 5044 Section 8 error code 3 ("Marker and ULPDU Length fields
do not agree on the start of an FPDU"), the correct framing-error
class for this inconsistency.
Fixes: 8b6a361b8c ("rdma/siw: receive path")
Link: https://patch.msgid.link/r/20260513175325.2042630-2-michael.bommarito@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Acked-by: Bernard Metzler <bernard.metzler@linux.dev>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix smbdirect_map_sges_from_iter() to use pre-decrement, not post-decrement
so that it cleans up the correct slots.
Fixes: e5fbdde430 ("cifs: Add a function to build an RDMA SGE list from an iterator")
Closes: https://sashiko.dev/#/patchset/20260326104544.509518-1-dhowells%40redhat.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Stefan Metzmacher <metze@samba.org>
cc: Paulo Alcantara <pc@manguebit.org>
cc: Tom Talpey <tom@talpey.com>
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
batadv_tp_recv_ack() and batadv_tp_stop() are only valid for tp_vars in the
BATADV_TP_SENDER role. When called with a BATADV_TP_RECEIVER role, it
proceeds to read sender-only members that were never initialized, leading
to undefined behavior.
This can be triggered when a node that is currently acting as a receiver in
an ongoing tp_meter session receives a malicious ACK packet.
Guard against this by checking tp_vars->role immediately after the
lookup and bailing out if it is not BATADV_TP_SENDER, before any of
those members are accessed.
Cc: stable@kernel.org
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Reviewed-by: Yuan Tan <yuantan098@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batadv_dat_forward_data() calls pskb_copy_for_clone() to duplicate an skb
for each DHT candidate, but does not check the return value before passing
it to batadv_send_skb_prepare_unicast_4addr(). That function dereferences
the skb unconditionally, so a failed allocation triggers a NULL pointer
dereference.
Skip forwarding to the current DHT candidate on allocation failure.
Cc: stable@kernel.org
Fixes: 785ea11441 ("batman-adv: Distributed ARP Table - create DHT helper functions")
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Reviewed-by: Yuan Tan <yuantan098@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Enable SR-IOV support for NVL platforms.
Signed-off-by: Jakub Kolakowski <jakub1.kolakowski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
Link: https://patch.msgid.link/20260331152259.58270-1-jakub1.kolakowski@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
A DMABUF exports access to BAR resources and, although they are
requested at startup time, we need to ensure they really were reserved
before exporting. Otherwise, it's possible to access unreserved
resources through the export.
Add a check to the DMABUF-creation path.
Fixes: 5d74781ebc ("vfio/pci: Add dma-buf export support for MMIO regions")
Signed-off-by: Matt Evans <mattev@meta.com>
Link: https://lore.kernel.org/r/20260511145829.2993601-3-mattev@meta.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
Previously BAR resource requests and the corresponding pci_iomap()
were performed on-demand and without synchronisation, which was racy.
Rather than add synchronisation, it's simplest to address this by
doing both activities from vfio_pci_core_enable().
The resource allocation and/or pci_iomap() can still fail; their
status is tracked and existing calls to vfio_pci_core_setup_barmap()
will fail in a similar way to before. This keeps the point of failure
as observed by userspace the same, i.e. failures to request/map unused
BARs are benign.
Fixes: 89e1f7d4c6 ("vfio: Add PCI device driver")
Signed-off-by: Matt Evans <mattev@meta.com>
Link: https://lore.kernel.org/r/20260511145829.2993601-2-mattev@meta.com
[ERR_PTR -> IOMEM_ERR_PTR per lkp report]
Signed-off-by: Alex Williamson <alex@shazbot.org>
ADXL is not present in Coreboot- or Slimbootloader-based BIOSes and as
result, the driver fails to probe there.
Since commit 2738c69a88 ("EDAC/i10nm: Add driver decoder for Ice Lake
and Tremont CPUs"), i10nm_edac supports driver decoder. Switch to driver
decoding when ADXL is not present.
Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: stable@vger.kernel.org # v6.1+
Link: https://patch.msgid.link/20260414181735.87023-1-anarsoul@gmail.com
Sashiko identified the leak at [1].
The ACPM driver allocates hardware mailbox channels using
`mbox_request_channel()` during `acpm_channels_init()`. However, the
driver lacked a `.remove` callback and did not free these channels on
subsequent error paths inside `acpm_probe()`.
Additionally, if `acpm_achan_alloc_cmds()` failed during the channel
initialization loop, the function returned immediately, bypassing the
manual cleanup and permanently leaking any channels successfully
requested in previous loop iterations.
Fix this by modifying `acpm_free_mbox_chans()` to match the `devres`
action signature and registering it via `devm_add_action_or_reset()`.
Cc: stable@vger.kernel.org
Fixes: a88927b534 ("firmware: add Exynos ACPM protocol driver")
Closes: https://sashiko.dev/#/patchset/20260420-acpm-tmu-v3-0-3dc8e93f0b26%40linaro.org [1]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260505-acpm-fixes-sashiko-reports-v5-2-43b5ee7f1674@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Sashiko identified a cross-thread RX length corruption bug when
reviewing the thermal addition to ACPM [1].
When multiple threads concurrently send IPC requests, the ACPM polling
mechanism can encounter responses belonging to other threads. To drain
the queue, the driver saves these concurrent responses into an internal
cache (`rx_data->cmd`) to be retrieved later by the owning thread.
Previously, the driver incorrectly used `xfer->rxcnt` (the expected
receive length of the *current* polling thread) when copying data for
*other* threads into this cache. If the threads expected responses of
different lengths, this resulted in buffer underflows (leading to reads
of uninitialized memory) or potential buffer overflows.
Fix this by replacing the boolean `response` flag in
`struct acpm_rx_data` with `rxcnt`, caching the exact expected receive
length for each specific transaction during transfer preparation. Use
this cached length when saving concurrent responses.
Consequently, ensure that `xfer->rxcnt` is explicitly zeroed in driver
helpers (e.g., `acpm_dvfs_set_xfer`) for fire-and-forget messages to
prevent uninitialized stack garbage from being interpreted as a massive
expected receive length.
Cc: stable@vger.kernel.org
Fixes: a88927b534 ("firmware: add Exynos ACPM protocol driver")
Closes: https://sashiko.dev/#/patchset/20260420-acpm-tmu-v3-0-3dc8e93f0b26%40linaro.org [1]
Reported-by: Titouan Ameline de Cadeville <titouan.ameline@gmail.com>
Closes: https://lore.kernel.org/r/20260426210255.73674-1-titouan.ameline@gmail.com/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260505-acpm-fixes-sashiko-reports-v5-1-43b5ee7f1674@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The drm_test_rect_calc_hscale and drm_test_rect_calc_vscale unit tests
intentionally trigger warning backtraces by providing bad parameters to
the tested functions. What is tested is the return value, not the existence
of a warning backtrace. Suppress the backtraces to avoid clogging the
kernel log and distraction from real problems. Additionally, the
suppression API allows to actually ensure a warning was triggered,
without parsing any kernel logs and keeping them clean.
The suppression check requires CONFIG_BUG enabled.
Link: https://lore.kernel.org/r/20260514-kunit_add_support-v11-3-b36a530a6d8f@redhat.com
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Acked-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Maíra Canal <mcanal@igalia.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alessandro Carminati <acarmina@redhat.com>
Acked-by: David Gow <david@davidgow.net>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add unit tests to verify that warning backtrace suppression works.
Tests cover both API forms:
- Scoped: kunit_warning_suppress() with in-block count verification
and post-block inactivity check.
- Direct functions: kunit_start/end_suppress_warning() with
sequential independent suppression blocks and per-block counts.
Furthermore, tests verify incremental warning counting, that
kunit_has_active_suppress_warning() transitions correctly around
suppression boundaries, and that suppression active in the test
kthread does not leak to a separate kthread.
If backtrace suppression does _not_ work, the unit tests will likely
trigger unsuppressed backtraces, which should actually help to get
the affected architectures / platforms fixed.
Link: https://lore.kernel.org/r/20260514-kunit_add_support-v11-2-b36a530a6d8f@redhat.com
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Acked-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alessandro Carminati <acarmina@redhat.com>
Reviewed-by: David Gow <david@davidgow.net>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Some unit tests intentionally trigger warning backtraces by passing bad
parameters to kernel API functions. Such unit tests typically check the
return value from such calls, not the existence of the warning backtrace.
Such intentionally generated warning backtraces are neither desirable
nor useful for a number of reasons:
- They can result in overlooked real problems.
- A warning that suddenly starts to show up in unit tests needs to be
investigated and has to be marked to be ignored, for example by
adjusting filter scripts. Such filters are ad hoc because there is
no real standard format for warnings. On top of that, such filter
scripts would require constant maintenance.
Solve the problem by providing a means to suppress warning backtraces
originating from the current kthread while executing test code. Since
each KUnit test runs in its own kthread, this effectively scopes
suppression to the test that enabled it. Limit changes to generic code
to the absolute minimum.
Implementation details:
Suppression is integrated into the existing KUnit hooks infrastructure
in test-bug.h, reusing the kunit_running static branch for zero
overhead when no tests are running.
Suppression is checked at three points in the warning path:
- In warn_slowpath_fmt(), the check runs before any output, fully
suppressing both message and backtrace. This covers architectures
without __WARN_FLAGS.
- In __warn_printk(), the check suppresses the warning message text.
This covers architectures that define __WARN_FLAGS but not their own
__WARN_printf (arm64, loongarch, parisc, powerpc, riscv, sh), where
the message is printed before the trap enters __report_bug().
- In __report_bug(), the check runs before __warn() is called,
suppressing the backtrace and stack dump.
To avoid double-counting on architectures where both __warn_printk()
and __report_bug() run for the same warning, kunit_is_suppressed_warning()
takes a bool parameter: true to increment the suppression counter
(used in warn_slowpath_fmt and __report_bug), false to check only
(used in __warn_printk).
The suppression state is dynamically allocated via kunit_kzalloc() and
tied to the KUnit test lifecycle via kunit_add_action(), ensuring
automatic cleanup at test exit. Writer-side access to the global
suppression list is serialized with a spinlock; readers use RCU.
Two API forms are provided:
- kunit_warning_suppress(test) { ... }: scoped, uses __cleanup for
automatic teardown on scope exit, kunit_add_action() as safety net
for abnormal exits (e.g. kthread_exit from failed assertions).
Suppression handle is only accessible inside the block.
- kunit_start/end_suppress_warning(test): direct functions returning
an explicit handle, for retaining the handle within the test,
or for cross-function usage.
Link: https://lore.kernel.org/r/20260514-kunit_add_support-v11-1-b36a530a6d8f@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alessandro Carminati <acarmina@redhat.com>
Reviewed-by: Kees Cook <kees@kernel.org>
Reviewed-by: David Gow <david@davidgow.net>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
batadv_gw_node_free() removes the gateway list entries during mesh teardown,
but it does not clear the currently selected gateway. This leaves stale
gateway state behind across cleanup and can break a later mesh recreation.
Clear bat_priv->gw.curr_gw before walking the gateway list so the selected
gateway reference is dropped as part of teardown.
Fixes: 2265c14108 ("batman-adv: gateway election code refactoring")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Ruijie Li <ruijieli51@gmail.com>
Signed-off-by: Zhanpeng Li <lzhanpeng2025@lzu.edu.cn>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
In the peric0_clk_regs array, the divider register offset for USI6 was
accidentally listed twice, while the divider for USI7 was omitted.
Missing this DIV register causes the USI7 clock divider setting to be
lost and reset to its hardware default value during a suspend/resume
cycle.
Replace the duplicated USI6 DIV entry with the correct USI7 DIV
register.
Fixes: 893f133a04 ("clk: samsung: gs101: add support for cmu_peric0")
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260505171457.1960837-1-visitorckw@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add ufs node for ExynosAutov920 SoC. Also enable ufs_phy and
ufs controller nodes.
Signed-off-by: Sowon Na <sowon.na@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://patch.msgid.link/20260417121452.827054-5-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Syscon HSI2 block has system configuration settings for
HSI IPs, like ufs, usb etc. Add a syscon_hsi2 node entry
so that related HSI controller can make use of the same.
Signed-off-by: Sowon Na <sowon.na@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://patch.msgid.link/20260417121452.827054-2-alim.akhtar@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use dev_err_probe() in tegra114_emc_interconnect_init() to make code a
bit simpler. It's preferred form of printing error messages during
probe, even if actual call cannot return EPROBE_DEFER.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260504190004.747509-4-krzysztof.kozlowski@oss.qualcomm.com
The Exynos850 APM co-processor relies on the I3C bus to communicate with
the PMIC. Currently, there is no dedicated PMIC consumer driver managing
these clocks, so the clock subsystem automatically gates them during the
initialisation. Once gated, any subsequent ACPM communication with APM
results in timeouts.
As a temporary workaround (and let's hope it doesn't become permanent),
mark both `gout_i3c_pclk` and `gout_i3c_sclk` as CLK_IS_CRITICAL ones to
prevent the clock subsystem from disabling them. This makes the ACPM
communication functional. This workaround should be reverted once a
proper ACPM PMIC driver is implemented to manage these clocks.
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20260430-exynos850-i3c-criticalclocks-v1-1-6e1fd8dfa21b@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
batman-adv keeps a running payload length for queued fragments and uses it
to validate a fragment chain before reassembly.
That accounting currently allows the accumulated fragment length to be
truncated during updates. As a result, malformed fragment chains can
bypass the intended validation and drive reassembly with inconsistent
length state, leading to a local denial of service.
Fix the accounting by storing the accumulated length in a length-typed
field and rejecting update overflows before the existing validation logic
runs.
The fix was verified against the original reproducer and against valid
fragment reassembly paths.
Fixes: 610bfc6bc9 ("batman-adv: Receive fragmented packets and merge")
Cc: stable@kernel.org
Reported-by: Yuan Tan <yuantan098@gmail.com>
Reported-by: Yifan Wu <yifanwucs@gmail.com>
Reported-by: Juefei Pu <tomapufckgml@gmail.com>
Reported-by: Xin Liu <bird@lzu.edu.cn>
Signed-off-by: Ruide Cao <caoruide123@gmail.com>
Tested-by: Ren Wei <enjou1224z@gmail.com>
Signed-off-by: Ren Wei <n05ec@lzu.edu.cn>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
With the support of nested lazy mmu sections it can happen that
arch_enter_lazy_mmu_mode() is being called twice without a call of
arch_leave_lazy_mmu_mode() in between, as the lazy_mmu_*() helpers
are not disabling preemption when checking for nested lazy mmu
sections.
This is a problem when running as a Xen PV guest, as
xen_enter_lazy_mmu() and xen_leave_lazy_mmu() don't tolerate this
case.
Fix that in xen_enter_lazy_mmu() and xen_leave_lazy_mmu() in order
not to hurt all other lazy mmu mode users.
Fixes: 291b3abed6 ("x86/xen: use lazy_mmu_state when context-switching")
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260508143933.493013-1-jgross@suse.com>
When swapping a not page-aligned E820 map entry with RAM, the start
address of the modified entry is calculated wrong (the offset into the
page is subtracted instead of being added to the page address).
Fixes: be35d91c88 ("xen: tolerate ACPI NVS memory overlapping with Xen allocated memory")
Reported-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20260505102417.208138-1-jgross@suse.com>
For gcc-16, the CONST_CAST macro family was removed. Add back what
we were using in gcc-common.h, as they are simple wrappers.
See GCC commits:
c3d96ff9e916c02584aa081f03ab999292efbb50
458c7926d48959abcb2c1adaa22458e27459a551
Suggested-by: Ingo Saitz <ingo@hannover.ccc.de>
Link: https://lore.kernel.org/lkml/ab6OKoay0OWkywjK@spatz.zoo
Fixes: 6b90bd4ba4 ("GCC plugin infrastructure")
Tested-by: Ivan Bulatovic <combuster@archlinux.us>
Tested-by: Christopher Cradock <christopher@cradock.myzen.co.uk>
Signed-off-by: Kees Cook <kees@kernel.org>
Instead of kzalloc and kcalloc, we can use a flex array to reduce to a
single allocation.
Also added __counted_by() for extra possible analysis.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://patch.msgid.link/20260304043420.14151-1-rosenp@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SMB2 READ response validation in cifs_readv_receive() and
handle_read_data() checks data_offset + data_len against the received
buffer length. Both values are attacker-controlled fields from the
server response and are stored as unsigned int, so the addition can
wrap before the bounds check:
fs/smb/client/transport.c:1259
if (!use_rdma_mr && (data_offset + data_len > buflen))
fs/smb/client/smb2ops.c:4839
else if (buf_len >= data_offset + data_len)
A malicious SMB server can use this to bypass validation. In the
non-encrypted receive path the client attempts an oversized socket
read and stalls for the SMB response timeout (180 seconds) before
reconnecting. In the SMB3 encrypted path, runtime testing shows the
malformed length can reach copy_to_iter() in handle_read_data() with
attacker-controlled size, where usercopy hardening stops the oversized
copy before bytes reach userspace.
Guard both call sites with check_add_overflow(), which is already
used elsewhere in this subsystem (smb2pdu.c). On overflow, treat the
response as malformed and reject with -EIO.
Signed-off-by: Jeremy Erazo <mendozayt13@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
-----BEGIN PGP SIGNATURE-----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=bV7l
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20260513' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fixes from Paul Moore:
- Correctly log the inheritable capabilities
- Honor AUDIT_LOCKED in the AUDIT_TRIM and AUDIT_MAKE_EQUIV commands
* tag 'audit-pr-20260513' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: enforce AUDIT_LOCKED for AUDIT_TRIM and AUDIT_MAKE_EQUIV
audit: fix incorrect inheritable capability in CAPSET records
atcphy_probe_switch() and atcphy_probe_mux() discard the pointers
returned by typec_switch_register() and typec_mux_register(). The
platform driver has no .remove callback, so when the driver unbinds
(e.g. via sysfs unbind) neither typec_switch_unregister() nor
typec_mux_unregister() is called. The framework reference taken in
typec_switch_register() (device_initialize() + device_add() in
drivers/usb/typec/mux.c) is therefore never dropped and the
typec_switch_dev / typec_mux_dev objects stay live forever, with
their sysfs entries under the typec_mux class also left behind. A
subsequent rebind cannot recreate them with the same fwnode-derived
name.
Save the registered handles and unregister them through
devm_add_action_or_reset() so framework registration is torn down
in step with the driver's other devm-managed state. While here,
drop struct apple_atcphy::sw and ::mux: they were declared with the
consumer-side types (typec_switch *, typec_mux *) instead of the
provider-side types and were never assigned.
Scope of the fix
================
This patch fixes the registration leak only. It does not close the
use-after-free window that arises when a consumer that obtained a
reference via fwnode_typec_switch_get() / fwnode_typec_mux_get()
outlives the provider unbind: such consumers keep the underlying
typec_switch_dev / typec_mux_dev alive past device_unregister(),
and a later typec_switch_set() / typec_mux_set() still invokes the
registered atcphy_sw_set() / atcphy_mux_set(), which dereferences
the freed apple_atcphy through typec_{switch,mux}_get_drvdata().
On Apple Silicon the relevant consumers are the typec port and the
cd321x controller registered by drivers/usb/typec/tipd/core.c.
Cable plug / orientation events and alt-mode transitions trigger
the .set callbacks via:
tps6598x_interrupt() drivers/usb/typec/tipd/core.c
tps6598x_handle_plug_event()
tps6598x_connect()/_disconnect()
typec_set_orientation() drivers/usb/typec/class.c
typec_switch_set(port->sw) drivers/usb/typec/mux.c
atcphy_sw_set() drivers/phy/apple/atc.c
cd321x_update_work() drivers/usb/typec/tipd/core.c
cd321x_typec_update_mode()
typec_mux_set(cd321x->mux) drivers/usb/typec/mux.c
atcphy_mux_set() drivers/phy/apple/atc.c
Closing that window requires framework support for invalidating
consumer-held references on provider unbind. The same
consumer-survives-provider pattern has been discussed for the PHY
framework [1] and is out of scope here.
[1] https://lore.kernel.org/linux-phy/aZejMSJ9qqRWb2pX@google.com/
Fixes: 8e98ca1e74 ("phy: apple: Add Apple Type-C PHY")
Signed-off-by: David Carlier <devnexen@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Joshua Peisach <jpeisach@ubuntu.com>
Link: https://lkml.kernel.org/r/6ec1ed08328340db42655287afd5fa4067316b11.camel@perches.com
Link: https://patch.msgid.link/20260508201958.30060-1-devnexen@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce support for EcoNet PCIe PHY controllers found in EN751221
and EN7528 SoCs, these SoCs are not identical but are similar, each
having one Gen1 port, and one Gen1/Gen2 port.
Co-developed-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
[cjd@cjdns.fr: add EN751221 support and refactor for clarity]
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://patch.msgid.link/20260425173642.406089-3-cjd@cjdns.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
EN751221 and EN7528 SoCs have two PCIe slots, and each one has a PHY
which behaves slightly differently because one slot is Gen1/Gen2 while
the other is Gen1 only.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260425173642.406089-2-cjd@cjdns.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When O_TMPFILE is set, the open mode needs to be passed to the kernel as
per the documentation. Currently this is not done.
Instead of checking for O_TMPFILE explicitly and making the conditionals
more complex, just always pass the mode to the kernel. If no value was
passed the mode will be garbage, but the kernel will ignore it anyways.
Fixes: a7604ba149 ("tools/nolibc/sys: make open() take a vararg on the 3rd argument")
Suggested-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/lkml/afRfjdovT6pNtwtP@1wt.eu/
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260514-nolibc-open-tmpfile-v2-3-b4c6c5efa266@weissschuh.net
This logic is duplicated and some upcoming extensions would require even
more duplicated logic.
Move it into a macro to avoid the duplication and allow cleaner changes.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260514-nolibc-open-tmpfile-v2-2-b4c6c5efa266@weissschuh.net
This logic is duplicated and its current form will be in the way of some
upcoming simplificiations.
Move it into a macro to avoid the duplication and enable some cleanups.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Link: https://patch.msgid.link/20260514-nolibc-open-tmpfile-v2-1-b4c6c5efa266@weissschuh.net
The RK3528 has a single USB2PHY with a otg and host port.
Add support for the RK3528 variant of USB2PHY.
PHY tuning for RK3528:
- Turn off differential receiver in suspend mode to save power
consumption.
- Set HS eye-height to 400mV instead of default 450mV.
- Choose the Tx fs/ls data as linestate from TX driver for otg port
which uses dwc3 controller to improve fs/ls devices compatibility with
long cables.
Undocumented magic-values are based on the linux-stan-6.1-rkr5 tag of
the vendor-kernel.
Signed-off-by: Jianwei Zheng <jianwei.zheng@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-6-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 480m clk is controlled using regs in the PHY address space and not
in the USB GRF address space on e.g. RK3528 and RK3506.
Add a clkout_ctl_phy usb2phy_reg to handle enable/disable of the 480m
clk on these SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-5-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The embedded USB2 PHY on RK3528 is very similar to the one in RK3568,
the main difference being that it only uses two clocks instead of three.
Add compatible to support the USB2 PHY in RK3528.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260505170410.3265305-4-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The logic to decide if usbgrf or grf should be used is more complex than
it needs to be. For RK3568, RV1108 and soon RK3528 we can assign the
rockchip,usbgrf regmap directly to grf instead of doing a usbgrf and grf
dance.
Simplify the code to only use the grf regmap and handle the logic of
what regmap should be used in driver probe instead.
The only expected change from this is that RK3528 can be supported
because of an addition of a of_property_present() check.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patch.msgid.link/20260505170410.3265305-3-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Typically these Rockchip USB2 PHYs are fully contained within a single
GRF. However, for RK3568 and RV1108 regs to control the USB2 PHY is
located in a different GRF compared to the base address.
Update this binding to require rockchip,usbgrf for RK3568 and RV1108 to
properly reflect that the USB GRF is required to control the USB2 PHYs
on these variants. Also disable use of rockchip,usbgrf for variants
where it is not required.
This should not introduce any breakage as the affected usb2phy nodes for
RK3568 and RV1108 were added together with a rockchip,usbgrf phandle in
their initial commit.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20260505170410.3265305-2-heiko@sntech.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This file does not use the symbols from the legacy
<linux/gpio.h> header, so let's drop it.
Reviewed-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The code like
int foo = X;
...
if (bar)
foo = Y;
is prone to subtle mistakes and hence harder to maintain as the foo value
may be changed inadvertently while code in '...' grown in lines. On top
it's harder to navigate to understand the possible values of foo when branch
is not taken (requires to look somewhere else in the code, far from the piece
at hand).
Besides that in case of taken branch the foo will be rewritten, which is
not a problem per se, just an unneeded operation.
Decouple assignment and definition to use if-else to address the inconveniences
described above.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of checking for the specific error codes (that can be considered
a layering violation to some extent) check for the property existence first
and then either parse it, or apply a default value.
With that, return an error when parsing of the existing property fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no code that uses ID table directly, except the
struct device_driver at the end of the file. Hence, move
table closer to its user. It's always possible to access
them via a pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use the generic firmware node interface for retrieving
device match data instead of the OF-specific one.
While at it, drop unneeded argument to devm_phy_create() which
extracts device node from the given device by default.
Reviewed-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20260513220336.369628-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
