This silences the following coccinelle warning:
drivers/s390/char/tape_34xx.c:360:38-39: WARNING: sum of probable bitmasks, consider |
we will try to make code cleaner
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Link: https://lore.kernel.org/r/1647846757-946-1-git-send-email-baihaowen@meizu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spec calls the XELPD_D/E ports just D/E, the platform prefix in the
domain names was only needed by the port->domain mapping relying on
matching enum values for the whole port/domain range (and the
corresponding aliasing between the platform specific domain enums).
Since a previous patch we can define the port->domain mapping explicitly
so do this by reusing the already existing D/E power domain names.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-18-imre.deak@intel.com
The DDI and AUX domain -> power well mappings are identical for a few
platforms/power well instances, reuse the mappings of earlier platforms
for these removing the duplicate mapping of new platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-17-imre.deak@intel.com
Aliasing the intel_display_power_domain enum values was required because
of the u64 power domain mask size limit. This makes the dmesg/debugfs
printouts of the domain names somewhat unclear, for instance domain
names for port D are shown on D12+ platforms where the corresponding
port is called TC1. Make this clearer by removing the aliasing which is
possible after a previous patch converting the mask to a bitmap.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-15-imre.deak@intel.com
Atm the port -> DDI and AUX power domain mapping is specified by relying
on the aliasing of the platform specific intel_display_power_domain enum
values. For instance D12+ platforms refer to the 'D' port and power
domain instances, which doesn't match the bspec terminology, on these
platforms the corresponding port is TC1. To make it clear what
port/domain the code refers to add a mapping between them which matches
the bspec terms on different display versions.
This also allows for removing the aliasing in enum values in a follow-up
patch.
v2: Add the functions to intel_display_power.c, use
intel_display_power_ prefix.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-14-imre.deak@intel.com
Instead of the skip_mask special casing of the ADL-S power well
descriptors, add a power well descriptor list for ADL-S as well reusing
the TGL descriptors, w/o the TC-cold power well. ADL-S doesn't have
TypeC PHYs, so a better way would be having ADL-S specific AUX
descriptors, but I left changing this for a follow-up.
This changes the ordering of the AUX and TC-cold vs. PW_4/5 power wells
on TGL and ADL-S, but this shouldn't make a difference (PW_4/5 don't
depend on the AUX/TC-cold power wells).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-13-imre.deak@intel.com
Simplify the definition of DG1 power wells by reusing the identical
RKL DDI/AUX descriptors.
This reorders the DG1 DDI/AUX vs. PW4/5 power wells, but this shouldn't
make a difference (it is the order on RKL and the DDI/AUX power wells
don't have a dependency on PW4/5).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-12-imre.deak@intel.com
Some power wells - like always-on and skl+/icl+ PW_1 - with the same
name, domain list, flags, ops are used by multiple platforms, so allow
platforms to reuse the descriptors of such power wells.
This change also lets the follow up patches to simplify the DG1/RKL
power well definitions, and remove the ADL-S skip_mask special casing.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-11-imre.deak@intel.com
All the port specific AUX/DDI_IO power wells share the same power well
ops struct and flags, so we can save some space and simplify the
definition of these by listing for all such power wells only the params
specific to them (name, domains, power well register index, id). Move
these params to a new i915_power_well_instance struct and convert the
per-platform power well definitions accordingly.
For all power well instance the name and power domain list params must
be specified, while the register index and id are optional, add the
I915_PW() macro that both simplifies the definitions and ensures that
the required params are set.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-10-imre.deak@intel.com
To remove the aliasing of the power domain enum values in a follow-up
patch in this patchset (requiring a bigger mask) and allow for defining
additional power domains in the future (at least some upcoming TypeC
changes requires this) convert the u64 i915_power_well_desc::domains
mask to a bitmap.
For simplicity I changed the for_each_power_domain_well() macros to
accept one domain only instead of a mask, as there isn't any current
user passing multiple domains.
v2: Don't add a typedef for the bitmap struct. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-9-imre.deak@intel.com
The next patch converts the i915_power_well_desc::domain mask from a u64
mask to a bitmap. I didn't find a reasonably simple way to initialize
bitmaps statically, so prepare for the next patch here by converting the
masks to an array of domain enums and initing the masks from these
arrays during module loading.
v2: Clarify list vs. array in the commit message. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-8-imre.deak@intel.com
Save some space by grouping the HSW power well descriptor flags along
with other flags in one bitfield.
This change also lets simplifying the definition of power well
descriptors sharing the same flags in an upcoming patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-5-imre.deak@intel.com
The DG2 fixed delay duration is always 600usec, so save some space in
the power well descriptors by converting the parameter to a flag. While
at it also use a bitfield for both the always_on and fixed_enable_delay
flag.
This change also lets simplifying the definiton of power wells sharing
the same flags in an upcoming patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-4-imre.deak@intel.com
Move the list of platform specific power domain -> power well
definitions to intel_display_power_map.c. While at it group the
platforms' power domain macros with the corresponding power well lists
and keep all the power domain lists in the same order (matching the enum
order).
No functional changes.
v2:
- s/intel_display_power_internal.h/intel_display_power_map.h/ (Jani)
- Simplify intel_cleanup_power_wells().
- Don't move intel_display_power_domain_str().
v3:
- Rename intel_init/cleanup_power_wells() to
intel_display_power_map_init/cleanup().
- Add documentation to intel_display_power_map_init/cleanup().
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-3-imre.deak@intel.com
Move the implementation of platform specific power well hooks to
intel_display_power_well.c, to reduce the clutter in
intel_display_power.c.
The locking of all the power domain/power well state is handled in the
power domain functions in intel_display_power.c using
i915_power_domains::lock. This patch also moves the
chy_phy_powergate_ch/lanes() functions to intel_display_power_well.c
which borrow the same lock to protect the DISPLAY_PHY_CONTROL register
state, which the HW uses both for toggling power wells and power gating
PHY lanes.
No functional change.
v2:
- Clarify in the commit log why CHV functions using the
i915_power_domains::lock were moved, while others locking the power
domain/well state were kept in intel_display_power.c . (Jouni)
- Move forward declaration of chv_phy_powergate_ch/lanes() to
intel_display_power_well.h .
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-1-imre.deak@intel.com
The return value of slab_pad_check is never used. So we can make it return
void now.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/r/20220419120352.37825-1-linmiaohe@huawei.com
Replace for spelling
keypresses to key presses
bytesize to byte size
specificly to specifically
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20220329195401.3220408-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ACPI is not enabled, cpuid_topo->llc_id = cpu_topo->llc_id = -1, which
will set llc_sibling 0xff(...), this is misleading.
Don't set llc_sibling(default 0) if we don't know the cache topology.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Wang Qing <wangqing@vivo.com>
Fixes: 37c3ec2d81 ("arm64: topology: divorce MC scheduling domain from core_siblings")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1649644580-54626-1-git-send-email-wangqing@vivo.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ampere Altra defines CPU clusters in the ACPI PPTT. They share a Snoop
Control Unit, but have no shared CPU-side last level cache.
cpu_coregroup_mask() will return a cpumask with weight 1, while
cpu_clustergroup_mask() will return a cpumask with weight 2.
As a result, build_sched_domain() will BUG() once per CPU with:
BUG: arch topology borken
the CLS domain not a subset of the MC domain
The MC level cpumask is then extended to that of the CLS child, and is
later removed entirely as redundant. This sched domain topology is an
improvement over previous topologies, or those built without
SCHED_CLUSTER, particularly for certain latency sensitive workloads.
With the current scheduler model and heuristics, this is a desirable
default topology for Ampere Altra and Altra Max system.
Rather than create a custom sched domains topology structure and
introduce new logic in arch/arm64 to detect these systems, update the
core_mask so coregroup is never a subset of clustergroup, extending it
to cluster_siblings if necessary. Only do this if CONFIG_SCHED_CLUSTER
is enabled to avoid also changing the topology (MC) when
CONFIG_SCHED_CLUSTER is disabled.
This has the added benefit over a custom topology of working for both
symmetric and asymmetric topologies. It does not address systems where
the CLUSTER topology is above a populated MC topology, but these are not
considered today and can be addressed separately if and when they
appear.
The final sched domain topology for a 2 socket Ampere Altra system is
unchanged with or without CONFIG_SCHED_CLUSTER, and the BUG is avoided:
For CPU0:
CONFIG_SCHED_CLUSTER=y
CLS [0-1]
DIE [0-79]
NUMA [0-159]
CONFIG_SCHED_CLUSTER is not set
DIE [0-79]
NUMA [0-159]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: D. Scott Phillips <scott@os.amperecomputing.com>
Cc: Ilkka Koskinen <ilkka@os.amperecomputing.com>
Cc: <stable@vger.kernel.org> # 5.16.x
Suggested-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Darren Hart <darren@os.amperecomputing.com>
Link: https://lore.kernel.org/r/c8fe9fce7c86ed56b4c455b8c902982dc2303868.1649696956.git.darren@os.amperecomputing.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Systems that do not support a Protected Processor Identification Number
currently report:
# cat /sys/devices/system/cpu/cpu0/topology/ppin
0x0
which is confusing/wrong.
Add a ".is_visible" function to suppress inclusion of the ppin file.
Fixes: ab28e94419 ("topology/sysfs: Add PPIN in sysfs under cpu topology")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20220406220150.63855-1-tony.luck@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new DG2 workaround added to fix some corner cases hangs.
v2:
- implementing the second and preferred option for this workaround
BSpec: 54077
BSpec: 68173
BSpec: 71488
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419182753.364237-2-jose.souza@intel.com
The ssd130x driver only provides the core support for these devices but it
does not have any bus transport logic. Add a driver to interface over SPI.
There is a difference in the communication protocol when using 4-wire SPI
instead of I2C. For the latter, a control byte that contains a D/C# field
has to be sent. This field tells the controller whether the data has to be
written to the command register or to the graphics display data memory.
But for 4-wire SPI that control byte is not used, instead a real D/C# line
must be pulled HIGH for commands data and LOW for graphics display data.
For this reason the standard SPI regmap can't be used and a custom .write
bus handler is needed.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-6-javierm@redhat.com
These are declared in the ssd130x-i2c transport driver but the information
is not I2C specific, and could be used by other SSD130x transport drivers.
Move them to the ssd130x core driver and just set the OF device entries to
an ID that could be used to lookup the correct device info from an array.
While being there, also move the SSD130X_DATA and SSD130X_COMMAND control
bytes. Since even though they are used by the I2C interface, they could
also be useful for other transport protocols such as SPI.
Suggested-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-5-javierm@redhat.com
The current compatible strings for SSD130x I2C controllers contain an "fb"
and "-i2c" suffixes. These have been deprecated and more correct ones were
added, that don't encode a subsystem or bus used to interface the devices.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-4-javierm@redhat.com
The Solomon SSD130x OLED displays can either have an I2C or SPI interface,
add to the schema the properties and examples for OLED devices under SPI.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-3-javierm@redhat.com
The current compatible strings for SSD130x I2C controllers contain both an
"fb" and "-i2c" suffixes. It seems to indicate that are for a fbdev driver
and also that are for devices that can be accessed over an I2C bus.
But a DT is supposed to describe the hardware and not Linux implementation
details. So let's deprecate those compatible strings and add new ones that
only contain the vendor and device name, without any of these suffixes.
These will just describe the device and can be matched by both I2C and SPI
DRM drivers. The required properties should still be enforced for old ones.
While being there, just drop the "sinowealth,sh1106-i2c" compatible string
since that was never present in a released Linux version.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419214824.335075-2-javierm@redhat.com
This patch addresses the checkpatch.pl flag that there should not be a
space after a cast.
Signed-off-by: Solomon Tan <wjsota@gmail.com>
Link: https://lore.kernel.org/r/20220419124318.8028-1-wjsota@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in rtllib_beacons_stop(), which is shown
below:
(Thread 1) | (Thread 2)
| rtllib_send_beacon()
rtllib_beacons_stop() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | rtllib_send_beacon_cb()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold ieee->beacon_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, rtllib_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417141641.124388-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in ieee80211_beacons_stop(), which is shown below:
(Thread 1) | (Thread 2)
| ieee80211_send_beacon()
ieee80211_beacons_stop() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | ieee80211_send_beacon_cb()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold ieee->beacon_lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, ieee80211_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417135407.109536-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add " == 0" to the condition in both else if branches to address a
possible bug. strcmp returns 0 when its arguments are equal, which
evaluates to false, often leading to errors when used in if statements.
Currently, the statement in the first else if branch does not execute
when its arguments are equal, but it does execute when crypt->ops->name
equals any string other than "WEP" or "TKIP".
Similarly, the second else if branch does not execute when its arguments
are equal, and it only executes when crypt->ops->name equals "TKIP".
The else branch never executes.
It is unlikely that this is working as intended.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rebecca Mckeever <remckee0@gmail.com>
Link: https://lore.kernel.org/r/20220416102434.97567-1-remckee0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable negative is being assigned a value that is never read, it is
being re-assigned later. The assignment is redundant and can be removed.
Cleans up clang scan build warning:
drivers/staging/iio/resolver/ad2s1210.c:502:3: warning: Value stored
to 'negative' is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220418134603.81336-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace macro VNSvInPortB with ioread8. Avoid cast of the return
value is possible with one exception.
The name of macro and the arguments use CamelCase which
is not accepted by checkpatch.pl
Since there are more than one checkpatch issue per line,
more steps are rquired to fix.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/fd71797d9d55d53f95c5c4e2df826bf85dd4626a.1650094595.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace macro MACvGPIOIn with VNSvInPortB.
Next patch will replace all macros VNSvInPortB with ioread8.
The names of macros and the arguments use CamelCase which
is not accepted by checkpatch.pl
Since there are more than one checkpatch issue per line,
more steps are rquired to fix.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/0a3c3eb0d4dad544fa281b34c5a70d4a3ab2d9f1.1650094595.git.philipp.g.hortmann@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It bothered me that during benchmarking using 'perf stat' (to collect
for example CPU cache events) I could not simultaneously retrieve the
times spend in user or kernel mode in a machine readable format.
When running 'perf stat' the output for humans contains the times
reported by rusage and wait4.
$ perf stat -e cache-misses:u -- true
Performance counter stats for 'true':
4,206 cache-misses:u
0.001113619 seconds time elapsed
0.001175000 seconds user
0.000000000 seconds sys
But 'perf stat's machine-readable format does not provide this information.
$ perf stat -x, -e cache-misses:u -- true
4282,,cache-misses:u,492859,100.00,,
I found no way to retrieve this information using the available events
while using machine-readable output.
This patch adds two new tool internal events 'user_time' and
'system_time', similarly to the already present 'duration_time' event.
Both events use the already collected rusage information obtained by
wait4 and tracked in the global ru_stats.
Examples presenting cache-misses and rusage information in both human
and machine-readable form:
$ perf stat -e duration_time,user_time,system_time,cache-misses -- grep -q -r duration_time .
Performance counter stats for 'grep -q -r duration_time .':
67,422,542 ns duration_time:u
50,517,000 ns user_time:u
16,839,000 ns system_time:u
30,937 cache-misses:u
0.067422542 seconds time elapsed
0.050517000 seconds user
0.016839000 seconds sys
$ perf stat -x, -e duration_time,user_time,system_time,cache-misses -- grep -q -r duration_time .
72134524,ns,duration_time:u,72134524,100.00,,
65225000,ns,user_time:u,65225000,100.00,,
6865000,ns,system_time:u,6865000,100.00,,
38705,,cache-misses:u,71189328,100.00,,
Signed-off-by: Florian Fischer <florian.fischer@muhq.space>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Link: https://lore.kernel.org/r/20220420102354.468173-3-florian.fischer@muhq.space
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch gets rid of the following error from checkpatch.pl:
WARNING: Unnecessary typecast of c90 int constant.
Signed-off-by: Solomon Tan <solomonbstoner@protonmail.ch>
Link: https://lore.kernel.org/r/YlxGTMBsLqdOIrpC@ArchDesktop
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adhere to linux coding style. Reported by checkpatch:
CHECK: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Soumya Negi <soumya.negi97@gmail.com>
Link: https://lore.kernel.org/r/20220416191745.7079-1-soumya.negi97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the only macro MAKEWORD that is in use and remove file
tmacro.h. File needs to be changed anyhow because of use of CamelCase
which is not accepted by checkpatch.pl. Reduced code provides
a better overview.
Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/20220416191622.GA11596@matrix-ESPRIMO-P710
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Unisys sub-tree of drivers/staging contains three drivers for the
"Unisys Secure Partition" (s-Par(R)): visorhba, visorinput, visornic.
They have no maintainers, in fact the only one that is listed in
MAINTAINERS has an unreacheable email address. During 2021 and 2022
several patches have been submitted to these drivers but nobody at
Unisys cared of reviewing the changes. Probably, also the
"sparmaintainer" internal list of unisys.com is not anymore read by
interested Unisys' engineers.
Therefore, remove the drivers/staging/unisys directory and delete the
relevant entries in the MAINTAINERS, Kconfig, Makefile files, then
remove also the drivers/visorbus directory which is not anymore needed
(it contained the driver for the virtualized bus for the Unisys s-Par
firmware).
Cc: David Kershner <david.kershner@unisys.com>
Cc: <sparmaintainer@unisys.com>
Cc: Ken Cox <jkc@redhat.com>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220414103217.32058-1-fmdefrancesco@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation for exporting rusage values as tool events.
Add new global stats tracking the values obtained via rusage.
For now only ru_utime and ru_stime are part of the tracked stats.
Both are stored as nanoseconds to be consistent with 'duration_time',
although the finest resolution the struct timeval data in rusage
provides are microseconds.
Signed-off-by: Florian Fischer <florian.fischer@muhq.space>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Xing Zhengjun <zhengjun.xing@linux.intel.com>
Link: https://lore.kernel.org/r/20220420102354.468173-2-florian.fischer@muhq.space
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The structures
rtw_ieee80211_hdr
rtw_ieee80211_hdr_3addr
rtw_ieee80211_hdr_3addr_qos
in drivers/staging/r8188eu/include/ieee80211.h just duplicate the
in-kernel structures from include/linux/ieee80211.h.
ieee80211_hdr
ieee80211_hdr_3addr
ieee80211_qos_hdr
Remove the rtw_ prefixed structures and use the in-kernel versions.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20220418180916.11311-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver allocates eighth urbs per xmit_buf, but uses only first urb.
Allocation of seven remaining urbs wastes memory for nothing.
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Ivan Safonov <insafonov@gmail.com>
Link: https://lore.kernel.org/r/20220417163608.42917-1-insafonov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ARRAY_SIZE instead of hard-coding the number of entries in the
mlme_sta_tbl array.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220417102221.466524-7-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the DoReserved function pointer with NULL in mlme_sta_tbl. We can
skip the function call for reserved subtypes.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220417102221.466524-6-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlme_sta_tbl is an array of struct mlme_handler. mlme_handler's num and
str components are not used. The code in mgt_dispatcher uses the subtype
number of the incoming frame to select the array entry for compiling the
repsonse.
We can remove struct mlme_handler and make mlme_sta_tbl an array of
function pointers.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220417102221.466524-5-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
