.boot.preserved.data is a better fit for ipl block than .boot.data
which is discarded after init. Reusing .boot.preserved.data allows to
simplify code a little bit and avoid copying data from .boot.data to
persistent variables.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce .boot.preserve.data section which is similar to .boot.data and
"shared" between the decompressor code and the decompressed kernel. The
decompressor will store values in it, and copy over to the decompressed
image before starting it. This method allows to avoid using pre-defined
addresses and other hacks to pass values between those boot phases.
Unlike .boot.data section .boot.preserved.data is NOT a part of init data,
and hence will be preserved for the kernel life time.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With commit 01396a374c ("s390/zcrypt: revisit ap device remove
procedure") the ap queue remove is now a two stage process. However,
a del_timer_sync() call may trigger the timer function which may
try to lock the very same spinlock as is held by the function
just initiating the del_timer_sync() call. This could end up in
a deadlock situation. Very unlikely but possible as you need to
remove an ap queue at the exact sime time when a timeout of a
request occurs.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Pierre Morel <pmorel@linux.ibm.com>
Fixes: commit 01396a374c ("s390/zcrypt: revisit ap device remove procedure")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The spinlock in the raw3270_view structure is used by con3270, tty3270
and fs3270 in different ways. For con3270 the lock can be acquired in
irq context, for tty3270 and fs3270 the highest context is bh.
Lockdep sees the view->lock as a single class and if the 3270 driver
is used for the console the following message is generated:
WARNING: inconsistent lock state
5.1.0-rc3-05157-g5c168033979d #12 Not tainted
--------------------------------
inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
swapper/0/1 [HC0[0]:SC1[1]:HE1:SE0] takes:
(____ptrval____) (&(&view->lock)->rlock){?.-.}, at: tty3270_update+0x7c/0x330
Introduce a lockdep subclass for the view lock to distinguish bh from
irq locks.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a chance we can see spurious interrupts in live
now. We have more engines enabled and that with more elaborate
access patterns with pm and display, increases the chances
hardware just makes a social call, without anything to work on.
Remove the error as we have tests to actually probe if
we really miss interrupt, instead of getting spurious ones.
Note that now we do write to intr_dw even with a zero
value. This is considered advantegous as the write
is an ack that sw is done.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410132124.21795-2-mika.kuoppala@linux.intel.com
Unlike previous gens, we already hold the irq_lock on
entering the rps handler so we can't use it as it is.
Make a gen11 specific rps interrupt handler without
locking.
v2: return early (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190410132124.21795-1-mika.kuoppala@linux.intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch aims to suppress 29 missing-break-in-switch false positives.
Addresses-Coverity-ID: 1456891 ("Missing break in switch")
Addresses-Coverity-ID: 1324063 ("Missing break in switch")
Addresses-Coverity-ID: 1324063 ("Missing break in switch")
Addresses-Coverity-ID: 141432 ("Missing break in switch")
Addresses-Coverity-ID: 141433 ("Missing break in switch")
Addresses-Coverity-ID: 141434 ("Missing break in switch")
Addresses-Coverity-ID: 141435 ("Missing break in switch")
Addresses-Coverity-ID: 141436 ("Missing break in switch")
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
The ASSIGN_OPS_HASH() macro was moved to fgraph.c where it was used, but for
some reason it wasn't removed from ftrace.c, as it is no longer referenced
there.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Most users of __raw_xsave_addr() use a feature number, shift it to a
mask and then __raw_xsave_addr() shifts it back to the feature number.
Make __raw_xsave_addr() use the feature number as an argument.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-11-bigeasy@linutronix.de
The MBUS clock is used by the MBUS controller, so let's export it so that
we can use it in our DT node.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The MBUS (and its associated controller) is the bus in the Allwinner SoCs
that DMA devices use in the system to access the memory.
Among other things (and depending on the SoC generation), it can also
enforce priorities or report bandwidth usages on a per-master basis.
One of the most notable thing is that instead of having the same mapping
for the RAM than the CPU, it maps it at address 0, which means we'll have
to do address translation thanks to the dma-ranges property.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a helper function that ensures the floating point registers for the
current task are active. Use with preemption disabled.
While at it, add fpregs_lock/unlock() helpers too, to be used in later
patches.
[ bp: Add a comment about its intended usage. ]
Signed-off-by: Rik van Riel <riel@surriel.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-10-bigeasy@linutronix.de
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-scsi, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num_queues' specified
by qemu is more than maxcpus, virtio-scsi would not be able to allocate
more than maxcpus vectors in order to have a vector for each queue. As a
result, it falls back into MSI-X with one vector for config and one shared
for queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-scsi by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When tag_set->nr_maps is 1, the block layer limits the number of hw queues
by nr_cpu_ids. No matter how many hw queues are used by virtio-blk, as it
has (tag_set->nr_maps == 1), it can use at most nr_cpu_ids hw queues.
In addition, specifically for pci scenario, when the 'num-queues' specified
by qemu is more than maxcpus, virtio-blk would not be able to allocate more
than maxcpus vectors in order to have a vector for each queue. As a result,
it falls back into MSI-X with one vector for config and one shared for
queues.
Considering above reasons, this patch limits the number of hw queues used
by virtio-blk by nr_cpu_ids.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The __reserved_mem_init_node will call region specific reserved memory
init codes, but once all compatibled init codes failed, the memory region
will left in memory.reserved and cause leakage.
Take cma reserve memory DTS for example, if user declare 1MB size,
which is not align to (PAGE_SIZE << max(MAX_ORDER - 1,
pageblock_order)), rmem_cma_setup will return -EINVAL.
Meanwhile, rmem_dma_setup will also return -EINVAL since "reusable"
property is not set. If finally there is no reserved memory init pick up
this memory, kernel will left the 1MB leak in memory.reserved.
This patch will remove this kind of memory from memory.reserved, only
when __reserved_mem_init_node return neither 0 nor -ENOENT.
Signed-off-by: pierre Kuo <vichy.kuo@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The node returned by of_graph_get_endpoint_by_regs has a reference taken,
and we need to put that reference back when done with the node.
However, the documentation for that node doesn't mention it, so let's make
sure it does.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
A node is always an object (aka a dictionary), so make that explicit for
child node schemas.
A meta-schema update will enforce having 'type' specified.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Devicetree binding reviews have a lot of repeated review comments. Much
of the guidelines aren't written down. This list of do's and don't's is
by no means an exhaustive guide for how to write bindings, but at least
the "rules" are written down in some form.
Signed-off-by: Rob Herring <robh@kernel.org>
user_fpu_begin() sets fpu_fpregs_owner_ctx to task's fpu struct. This is
always the case since there is no lazy FPU anymore.
fpu_fpregs_owner_ctx is used during context switch to decide if it needs
to load the saved registers or if the currently loaded registers are
valid. It could be skipped during a
taskA -> kernel thread -> taskA
switch because the switch to the kernel thread would not alter the CPU's
sFPU tate.
Since this field is always updated during context switch and
never invalidated, setting it manually (in user context) makes no
difference. A kernel thread with kernel_fpu_begin() block could
set fpu_fpregs_owner_ctx to NULL but a kernel thread does not use
user_fpu_begin().
This is a leftover from the lazy-FPU time.
Remove user_fpu_begin(), it does not change fpu_fpregs_owner_ctx's
content.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-9-bigeasy@linutronix.de
The function bfq_bfqq_expire() invokes the function
__bfq_bfqq_expire(), and the latter may free the in-service bfq-queue.
If this happens, then no other instruction of bfq_bfqq_expire() must
be executed, or a use-after-free will occur.
Basing on the assumption that __bfq_bfqq_expire() invokes
bfq_put_queue() on the in-service bfq-queue exactly once, the queue is
assumed to be freed if its refcounter is equal to one right before
invoking __bfq_bfqq_expire().
But, since commit 9dee8b3b05 ("block, bfq: fix queue removal from
weights tree") this assumption is false. __bfq_bfqq_expire() may also
invoke bfq_weights_tree_remove() and, since commit 9dee8b3b05
("block, bfq: fix queue removal from weights tree"), also
the latter function may invoke bfq_put_queue(). So __bfq_bfqq_expire()
may invoke bfq_put_queue() twice, and this is the actual case where
the in-service queue may happen to be freed.
To address this issue, this commit moves the check on the refcounter
of the queue right around the last bfq_put_queue() that may be invoked
on the queue.
Fixes: 9dee8b3b05 ("block, bfq: fix queue removal from weights tree")
Reported-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The struct fpu.initialized member is always set to one for user tasks
and zero for kernel tasks. This avoids saving/restoring the FPU
registers for kernel threads.
The ->initialized = 0 case for user tasks has been removed in previous
changes, for instance, by doing an explicit unconditional init at fork()
time for FPU-less systems which was otherwise delayed until the emulated
opcode.
The context switch code (switch_fpu_prepare() + switch_fpu_finish())
can't unconditionally save/restore registers for kernel threads. Not
only would it slow down the switch but also load a zeroed xcomp_bv for
XSAVES.
For kernel_fpu_begin() (+end) the situation is similar: EFI with runtime
services uses this before alternatives_patched is true. Which means that
this function is used too early and it wasn't the case before.
For those two cases, use current->mm to distinguish between user and
kernel thread. For kernel_fpu_begin() skip save/restore of the FPU
registers.
During the context switch into a kernel thread don't do anything. There
is no reason to save the FPU state of a kernel thread.
The reordering in __switch_to() is important because the current()
pointer needs to be valid before switch_fpu_finish() is invoked so ->mm
is seen of the new task instead the old one.
N.B.: fpu__save() doesn't need to check ->mm because it is called by
user tasks only.
[ bp: Massage. ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Aubrey Li <aubrey.li@intel.com>
Cc: Babu Moger <Babu.Moger@amd.com>
Cc: "Chang S. Bae" <chang.seok.bae@intel.com>
Cc: Dmitry Safonov <dima@arista.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Nicolai Stange <nstange@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-8-bigeasy@linutronix.de
snd_hdac_display_power() doesn't handle the concurrent calls carefully
enough, and it may lead to the doubly get_power or put_power calls,
when a runtime PM and an async work get called in racy way.
This patch addresses it by reusing the bus->lock mutex that has been
used for protecting the link state change in ext bus code, so that it
can protect against racy display state changes. The initialization of
bus->lock was moved from snd_hdac_ext_bus_init() to
snd_hdac_bus_init() as well accordingly.
Testcase: igt/i915_pm_rpm/module-reload #glk-dsi
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To calculate a remaining time, it's required to subtract the current time
from the expiration time. In alarm_timer_remaining() the arguments of
ktime_sub are swapped.
Fixes: d653d8457c ("alarmtimer: Implement remaining callback")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190408041542.26338-1-avagin@gmail.com
snd_hdac_display_power() doesn't handle the concurrent calls carefully
enough, and it may lead to the doubly get_power or put_power calls,
when a runtime PM and an async work get called in racy way.
This patch addresses it by reusing the bus->lock mutex that has been
used for protecting the link state change in ext bus code, so that it
can protect against racy display state changes. The initialization of
bus->lock was moved from snd_hdac_ext_bus_init() to
snd_hdac_bus_init() as well accordingly.
Testcase: igt/i915_pm_rpm/module-reload #glk-dsi
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/s5h8swiunph.wl-tiwai@suse.de
Commit 7769db5883 ("drm/i915/dp: optimize eDP 1.4+ link config fast
and narrow") started to optize the eDP 1.4+ link config, both per spec
and as preparation for display stream compression support.
Sadly, we again face panels that flat out fail with parameters they
claim to support. Revert, and go back to the drawing board.
v2: Actually revert to max params instead of just wide-and-slow.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109959
Fixes: 7769db5883 ("drm/i915/dp: optimize eDP 1.4+ link config fast and narrow")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.0+
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Albert Astals Cid <aacid@kde.org> # v5.0 backport
Tested-by: Emanuele Panigati <ilpanich@gmail.com> # v5.0 backport
Tested-by: Matteo Iervasi <matteoiervasi@gmail.com> # v5.0 backport
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190405075220.9815-1-jani.nikula@intel.com
In commit
72a671ced6 ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels")
the 32bit and 64bit path of the signal delivery code were merged.
The 32bit version:
int save_i387_xstate_ia32(void __user *buf)
…
if (cpu_has_xsave)
return save_i387_xsave(fp);
if (cpu_has_fxsr)
return save_i387_fxsave(fp);
The 64bit version:
int save_i387_xstate(void __user *buf)
…
if (user_has_fpu()) {
if (use_xsave())
err = xsave_user(buf);
else
err = fxsave_user(buf);
if (unlikely(err)) {
__clear_user(buf, xstate_size);
return err;
The merge:
int save_xstate_sig(void __user *buf, void __user *buf_fx, int size)
…
if (user_has_fpu()) {
/* Save the live register state to the user directly. */
if (save_user_xstate(buf_fx))
return -1;
/* Update the thread's fxstate to save the fsave header. */
if (ia32_fxstate)
fpu_fxsave(&tsk->thread.fpu);
I don't think that we needed to save the FPU registers to ->thread.fpu
because the registers were stored in buf_fx. Today the state will be
restored from buf_fx after the signal was handled (I assume that this
was also the case with lazy-FPU).
Since commit
66463db4fc ("x86, fpu: shift drop_init_fpu() from save_xstate_sig() to handle_signal()")
it is ensured that the signal handler starts with clear/fresh set of FPU
registers which means that the previous store is futile.
Remove the copy_fxregs_to_kernel() call because task's FPU state is
cleared later in handle_signal() via fpu__clear().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jann Horn <jannh@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190403164156.19645-7-bigeasy@linutronix.de
IO enable sequencing needs ddi clocks enabled.
These clocks will be gated at a later point in
the enable sequence.
v2: Fix the commit header (Uma)
v3: Remove the redundant read (Ville)
Fixes: 949fc52af1 ("drm/i915/icl: add pll mapping for DSI")
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553513202-13863-1-git-send-email-vandita.kulkarni@intel.com
pr_fmt() should be defined before including linux/printk.h, either
directly or indirectly, in order to avoid redefinition of the macro.
Currently the macro definition is in habanalabs.h, which is included in
many files, and that makes the addition/reorder of includes to be prone
to compilation errors.
This patch cancels this dependency by defining the macro only in the few
source files that use it.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The original patch neglected to take byte order conversions
into account, fix that.
Fixes: d9bb410888 ("mac80211: allow overriding HT STBC capabilities")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
U2F Zero supports custom commands for blinking the LED and getting data
from the internal hardware RNG. Expose the blinking function as a LED
device, and the internal hardware RNG as an HWRNG so that it can be used
to feed the enthropy pool.
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following commit:
a0b0fd53e1 ("locking/lockdep: Free lock classes that are no longer in use")
changed the behavior of lockdep_free_key_range() from
unconditionally zapping lock classes into only zapping lock classes if
debug_lock == true. Not zapping lock classes if debug_lock == false leaves
dangling pointers in several lockdep datastructures, e.g. lock_class::name
in the all_lock_classes list.
The shell command "cat /proc/lockdep" causes the kernel to iterate the
all_lock_classes list. Hence the "unable to handle kernel paging request" cash
that Shenghui encountered by running cat /proc/lockdep.
Since the new behavior can cause cat /proc/lockdep to crash, restore the
pre-v5.1 behavior.
This patch avoids that cat /proc/lockdep triggers the following crash
with debug_lock == false:
BUG: unable to handle kernel paging request at fffffbfff40ca448
RIP: 0010:__asan_load1+0x28/0x50
Call Trace:
string+0xac/0x180
vsnprintf+0x23e/0x820
seq_vprintf+0x82/0xc0
seq_printf+0x92/0xb0
print_name+0x34/0xb0
l_show+0x184/0x200
seq_read+0x59e/0x6c0
proc_reg_read+0x11f/0x170
__vfs_read+0x4d/0x90
vfs_read+0xc5/0x1f0
ksys_read+0xab/0x130
__x64_sys_read+0x43/0x50
do_syscall_64+0x71/0x210
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: shenghui <shhuiw@foxmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: a0b0fd53e1 ("locking/lockdep: Free lock classes that are no longer in use") # v5.1-rc1.
Link: https://lkml.kernel.org/r/20190403233552.124673-1-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Handle error before returning when try_module_get() fails
to prevent inconsistent mutex lock/unlock.
Fixes: 52034add7 (ASoC: pcm: update module refcount if
module_get_upon_open is set)
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before commit c5459b829b ("LSM: Plumb visibility into optional "enabled"
state"), /sys/module/apparmor/parameters/enabled would show "Y" or "N"
since it was using the "bool" handler. After being changed to "int",
this switched to "1" or "0", breaking the userspace AppArmor detection
of dbus-broker. This restores the Y/N output while keeping the LSM
infrastructure happy.
Before:
$ cat /sys/module/apparmor/parameters/enabled
1
After:
$ cat /sys/module/apparmor/parameters/enabled
Y
Reported-by: David Rheinsberg <david.rheinsberg@gmail.com>
Reviewed-by: David Rheinsberg <david.rheinsberg@gmail.com>
Link: https://lkml.kernel.org/r/CADyDSO6k8vYb1eryT4g6+EHrLCvb68GAbHVWuULkYjcZcYNhhw@mail.gmail.com
Fixes: c5459b829b ("LSM: Plumb visibility into optional "enabled" state")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>
These fields are only used in anatop_regulator_probe() so use local
variables instead. The *initdata is not used so can be removed.
The *anatop is renamed to *regmap for better readability.
Use u32 instead of int for the variables used as third argument of
of_property_read_u32().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The S2MPA01_REGULATOR_CNT is no longer used after converted to use
simplified DT parsing.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rdev->desc->enable_mask setting is always the same as
BIT(regulator->ctrl_mask), so just use rdev->desc->enable_mask instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators array should never need to be modified, make it const so
compiler can put it to .rodata.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When master clock is used, master clock rate is set exclusively.
Parent clocks of master clock cannot be changed after a call to
clk_set_rate_exclusive(). So the parent clock of SAI kernel clock
must be set before.
Ensure also that exclusive rate operations are balanced
in STM32 SAI driver.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix wrong setting on number of channels. The context wants to set
constraint to 2 channels instead of 4.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Spurious interrupt support was added to perf in the following commit, almost
a decade ago:
63e6be6d98 ("perf, x86: Catch spurious interrupts after disabling counters")
The two previous patches (resolving the race condition when disabling a
PMC and NMI latency mitigation) allow for the removal of this older
spurious interrupt support.
Currently in x86_pmu_stop(), the bit for the PMC in the active_mask bitmap
is cleared before disabling the PMC, which sets up a race condition. This
race condition was mitigated by introducing the running bitmap. That race
condition can be eliminated by first disabling the PMC, waiting for PMC
reset on overflow and then clearing the bit for the PMC in the active_mask
bitmap. The NMI handler will not re-enable a disabled counter.
If x86_pmu_stop() is called from the perf NMI handler, the NMI latency
mitigation support will guard against any unhandled NMI messages.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's no include/dt-bindings/i3c/ directory, remove this F: entry
from the I3C file patterns.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Reported-by: Joe Perches <joe@perches.com>
Fixes: 4f26d06669 ("MAINTAINERS: Add myself as the I3C subsystem maintainer")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The controller was being disabled incorrectly. The correct way is to clear
the DEV_CTRL_ENABLE bit.
Fix this by clearing this bit.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 1dd728f5d4 ("i3c: master: Add driver for Synopsys DesignWare IP")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
The validation of random PID should be done by checking the
boardinfo->pid instead of info.pid which is empty.
Doing the change the info struture declaration is no longer necessary.
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
This patch adds CMT{0|1|2|3} device nodes for r8a77990 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CMT{0|1|2|3} device nodes for r8a77965 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CMT{0|1|2|3} device nodes for r8a7795 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For an uncontended rwsem, count and owner are the only fields a task
needs to touch when acquiring the rwsem. So they are put next to each
other to increase the chance that they will share the same cacheline.
On a ThunderX2 99xx (arm64) system with 32K L1 cache and 256K L2
cache, a rwsem locking microbenchmark with one locking thread was
run to write-lock and write-unlock an array of rwsems separated 2
cachelines apart in a 1M byte memory block. The locking rates (kops/s)
of the microbenchmark when the rwsems are at various "long" (8-byte)
offsets from beginning of the cacheline before and after the patch were
as follows:
Cacheline Offset Pre-patch Post-patch
---------------- --------- ----------
0 17,449 16,588
1 17,450 16,465
2 17,450 16,460
3 17,453 16,462
4 14,867 16,471
5 14,867 16,470
6 14,853 16,464
7 14,867 13,172
Before the patch, the count and owner are 4 "long"s apart. After the
patch, they are only 1 "long" apart.
The rwsem data have to be loaded from the L3 cache for each access. It
can be seen that the locking rates are more consistent after the patch
than before. Note that for this particular system, the performance
drop happens whenever the count and owner are at an odd multiples of
"long"s apart. No performance drop was observed when only a single rwsem
was used (hot cache). So the drop is likely just an idiosyncrasy of the
cache architecture of this chip than an inherent problem with the patch.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20190404174320.22416-12-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add lock event counting calls so that we can track the number of lock
events happening in the rwsem code.
With CONFIG_LOCK_EVENT_COUNTS on and booting a 4-socket 112-thread x86-64
system, the rwsem counts after system bootup were as follows:
rwsem_opt_fail=261
rwsem_opt_wlock=50636
rwsem_rlock=445
rwsem_rlock_fail=0
rwsem_rlock_fast=22
rwsem_rtrylock=810144
rwsem_sleep_reader=441
rwsem_sleep_writer=310
rwsem_wake_reader=355
rwsem_wake_writer=2335
rwsem_wlock=261
rwsem_wlock_fail=0
rwsem_wtrylock=20583
It can be seen that most of the lock acquisitions in the slowpath were
write-locks in the optimistic spinning code path with no sleeping at
all. For this system, over 97% of the locks are acquired via optimistic
spinning. It illustrates the importance of optimistic spinning in
improving the performance of rwsem.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20190404174320.22416-11-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On bare metal, the pvqspinlock event counts will always be 0. So there
is no point in showing their corresponding debugfs files. So they are
skipped in this case.
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20190404174320.22416-10-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
