Commit b0f847e16c ("HID: hid-sensor-hub: Force logical minimum to 1 for
power and report state") not only replaced the descriptor fixup done for
devices with the HID_SENSOR_HUB_ENUM_QUIRK with a generic fix, but also
accidentally removed the unrelated descriptor fixup for the Lenovo ThinkPad
Helix 2 sensor hub. This commit restores this fixup.
Restoring this fixup not only fixes the Lenovo ThinkPad Helix 2's sensors,
but also the Lenovo ThinkPad 8's sensors.
Fixes: b0f847e16c ("HID: hid-sensor-hub: Force logical minimum ...")
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Fernando D S Lima <fernandodsl@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add HID quirk driver for Xbox One S controller over bluetooth.
This driver only adds support for rumble. Standard controller
functionality is exposed by default HID driver.
[jkosina@suse.cz: straightforward rebase on more recent driver code]
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Signed-off-by: Juha Kuikka <juha.kuikka@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In order to be able to have more than just an unsigned long worth of
private data, convert the code to allocate and use a dedicated struct.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Signed-off-by: Juha Kuikka <juha.kuikka@gmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add validation check for wmm rule when copy rules from fwdb and print
error when rule is invalid.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are three features used by various Logitech mice for
high-resolution scrolling: the scrolling acceleration bit in HID++ 1.0,
and the x2120 and x2121 features in HID++ 2.0 and above. This patch
supports all three, and uses the multiplier reported by the mouse for
the HID++ 2.0+ features.
The full list of product IDs of mice which support high-resolution
scrolling was provided by Logitech, but the patch was tested using the
following mice (using the Unifying receiver):
* HID++ 1.0: Anywhere MX, Performance MX
* x2120: M560
* x2121: MX Anywhere 2, MX Master 2S
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
"Scrolling acceleration" is a bit of a misnomer: it doesn't deal with
acceleration at all. However, that's the name used in Logitech's spec,
so I used it here.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To avoid code duplication, this class counts high-resolution scroll
movements and emits the legacy low-resolution events when appropriate.
Drivers should be able to create one instance for each scroll wheel that
they need to handle.
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This event code represents scroll reports from high-resolution wheels,
and will be used by future patches in this series. See the linux-input
"Reporting high-resolution scroll events" thread [0] for more details.
[0]: https://www.spinics.net/lists/linux-input/msg57380.html
Signed-off-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a NULL pointer dereference in case memory resources
for *parse* are not successfully allocated.
Fix this by adding a new goto label and make the execution
path jump to it in case vzalloc() fails.
Addresses-Coverity-ID: 1473081 ("Dereference after null check")
Fixes: b2dd9f2e5a ("HID: core: fix memory leak on probe")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Core regulatory hints didn't set wiphy_idx to WIPHY_IDX_INVALID. Since
the regulatory request is zeroed, wiphy_idx was always implicitly set to
0. This resulted in updating only phy #0.
Fix that.
Fixes: 806a9e3967 ("cfg80211: make regulatory_request use wiphy_idx instead of wiphy")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise the offchannel frame might be queued due to
IEEE80211_QUEUE_STOP_REASON_PS and later dropped (in
ieee80211_tx_frags()). Anyway, it doesn't make much sense to wake up
the device during ROC.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame is dropped for any reason, mac80211 wouldn't report the TX
status back to user space.
As the user space may rely on the TX_STATUS to kick its state
machines, resends etc, it's better to just report this frame as not
acked instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers able to correctly replace a in-use key should set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to allow the user space (e.g.
hostapd or wpa_supplicant) to rekey PTK keys.
The user space must detect a PTK rekey attempt and only go ahead with it
when the driver has set this flag. If the driver is not supporting the
feature the user space either must not replace the PTK key or perform a
full re-association instead.
Ignoring this flag and continuing to rekey the connection can still work
but has to be considered insecure and broken. Depending on the driver it
can leak clear text packets or freeze the connection and is only
supported to allow the user space to be updated.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.
Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE 802.11-2016 extended the VHT capability fields to allow
indicating the number of spatial streams depending on the
actually used bandwidth, add support for decoding this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as for HT and VHT.
This helps the lower level to know whether the AP supports HE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The defines of IEEE80211_HE_OPERATION_VHT_OPER_INFO and
IEEE80211_HE_OPERATION_MULTI_BSSID_AP have leading zeroes
that makes the number look like it is bigger than 32 bit.
This is misleading, remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch enable the AHCI controller.
Since this controller need two regulator, this patch add them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 have a sata controller which is the same as A20.
This patch adds a DT node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some boards have HDMI VCC pin connected to voltage regulator which may
not be turned on by default.
Add support for such boards by adding voltage regulator handling code to
HDMI driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Icenowy: change supply name to "hvcc"]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-11-icenowy@aosc.io
Allwiner SoCs with DesignWare HDMI controller all come with a "HVCC"
pin, which is the VCC of HDMI part.
Add a supply property to specify HVCC's regulator in the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-10-icenowy@aosc.io
Allwinner A64 HDMI PHY clock has PLL_VIDEO0 as a parent.
Include the macro on dt-bindings so-that the same can be used
while defining CCU clock phandles.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The HDMI controller on Allwinner A64 is similar on the one on
H3/H5/A83T (although the PHY is different with A83T).
Add A64 compatible and append A83T compatible as fallback.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Icenowy: refactor commit log]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-7-icenowy@aosc.io
Display Engine(DE2) in Allwinner A64 has two mixers and tcons.
The routing for mixer0 is through tcon0 and connected to
LVDS/RGB/MIPI-DSI controller.
The routing for mixer1 is through tcon1 and connected to HDMI.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-6-icenowy@aosc.io
Mixers in Allwinner have similar capabilities as others SoCs with DE2.
Add support for them.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: Add mixer1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-5-icenowy@aosc.io
Allwinner A64 has a DE2 display pipeline. The TCONs are similar to the
ones in A83T, but the mixers are new (similar to the later R40 SoC).
This patch adds dt-binding documentation for A64 DE2 display pipeline.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[Icenowy: Refactor and also cover TCON1]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180904044053.15425-4-icenowy@aosc.io
Video PLLs on A64 can be set to higher rate that it is actually
supported by HW.
Limit maximum rate to 1008 MHz. This is the maximum allowed rate by BSP
clock driver. Interestengly, user manual specifies maximum frequency to
be 600 MHz. Historically, this data was wrong in some user manuals for
other SoCs, so more faith is put in BSP clock driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to documentation and experience with other similar SoCs, video
PLLs don't work stable if their output frequency is set below 192 MHz.
Because of that, set minimal rate to both A64 video PLLs to 192 MHz.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enable DRM Support for Allwinner Display Engine, built as a module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the H6, the MMC module clocks are fixed in the new timing mode,
i.e. they do not have a bit to select the mode. These clocks have
a 2x divider somewhere between the clock and the MMC module.
To be consistent with other SoCs supporting the new timing mode,
we model the 2x divider as a fixed post-divider on the MMC module
clocks.
This patch adds the post-dividers to the MMC clocks, following the
approach on A64.
Fixes: 524353ea48 ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Use the new of_get_compatible_child() helper to lookup the slot child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix up the related slot-node reference leak.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Cc: stable <stable@vger.kernel.org> # 4.15
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a potential execution path in which pointer memfd is NULL when
passed as argument to fput(), hence there is a NULL pointer dereference
in fput().
Fix this by null checking *memfd* before calling fput().
Addresses-Coverity-ID: 1473174 ("Explicit null dereferenced")
Fixes: fbb0de7950 ("Add udmabuf misc device")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180904190749.GA9308@embeddedor.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>