The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver was rejecting almost all unsupported
parameters already, it was only missing a check
for tx_max_coalesced_frames_irq.
As a side effect of these changes the error code for
unsupported params changes from ENOTSUPP to EOPNOTSUPP.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters
(other than adaptive rx, which will now be rejected by core).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting fallthrough comments to fallthrough; creates warnings
in this code when compiled with gcc.
This code is overly complicated and reads rather better with a
little refactoring and no fallthrough uses at all.
Remove the fallthrough comments and simplify the written source
code while reducing the object code size.
Consolidate duplicated switch/case blocks for IPV4 and IPV6.
defconfig x86-64 with sfc:
$ size drivers/net/ethernet/sfc/ethtool.o*
text data bss dec hex filename
10055 12 0 10067 2753 drivers/net/ethernet/sfc/ethtool.o.new
10135 12 0 10147 27a3 drivers/net/ethernet/sfc/ethtool.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ 7329.671518] BUG: KCSAN: data-race in flush_workqueue / flush_workqueue
[ 7329.671549]
[ 7329.671572] write to 0xffff8881f65fb250 of 8 bytes by task 37173 on cpu 2:
[ 7329.671607] flush_workqueue+0x3bc/0x9b0 (kernel/workqueue.c:2844)
[ 7329.672527]
[ 7329.672540] read to 0xffff8881f65fb250 of 8 bytes by task 37175 on cpu 0:
[ 7329.672571] flush_workqueue+0x28d/0x9b0 (kernel/workqueue.c:2835)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There was a bug that was causing packets to be sent to the driver
without first calling dequeue() on the "child" qdisc. And the KASAN
report below shows that sending a packet without calling dequeue()
leads to bad results.
The problem is that when checking the last qdisc "child" we do not set
the returned skb to NULL, which can cause it to be sent to the driver,
and so after the skb is sent, it may be freed, and in some situations a
reference to it may still be in the child qdisc, because it was never
dequeued.
The crash log looks like this:
[ 19.937538] ==================================================================
[ 19.938300] BUG: KASAN: use-after-free in taprio_dequeue_soft+0x620/0x780
[ 19.938968] Read of size 4 at addr ffff8881128628cc by task swapper/1/0
[ 19.939612]
[ 19.939772] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.6.0-rc3+ #97
[ 19.940397] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qe4
[ 19.941523] Call Trace:
[ 19.941774] <IRQ>
[ 19.941985] dump_stack+0x97/0xe0
[ 19.942323] print_address_description.constprop.0+0x3b/0x60
[ 19.942884] ? taprio_dequeue_soft+0x620/0x780
[ 19.943325] ? taprio_dequeue_soft+0x620/0x780
[ 19.943767] __kasan_report.cold+0x1a/0x32
[ 19.944173] ? taprio_dequeue_soft+0x620/0x780
[ 19.944612] kasan_report+0xe/0x20
[ 19.944954] taprio_dequeue_soft+0x620/0x780
[ 19.945380] __qdisc_run+0x164/0x18d0
[ 19.945749] net_tx_action+0x2c4/0x730
[ 19.946124] __do_softirq+0x268/0x7bc
[ 19.946491] irq_exit+0x17d/0x1b0
[ 19.946824] smp_apic_timer_interrupt+0xeb/0x380
[ 19.947280] apic_timer_interrupt+0xf/0x20
[ 19.947687] </IRQ>
[ 19.947912] RIP: 0010:default_idle+0x2d/0x2d0
[ 19.948345] Code: 00 00 41 56 41 55 65 44 8b 2d 3f 8d 7c 7c 41 54 55 53 0f 1f 44 00 00 e8 b1 b2 c5 fd e9 07 00 3
[ 19.950166] RSP: 0018:ffff88811a3efda0 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13
[ 19.950909] RAX: 0000000080000000 RBX: ffff88811a3a9600 RCX: ffffffff8385327e
[ 19.951608] RDX: 1ffff110234752c0 RSI: 0000000000000000 RDI: ffffffff8385262f
[ 19.952309] RBP: ffffed10234752c0 R08: 0000000000000001 R09: ffffed10234752c1
[ 19.953009] R10: ffffed10234752c0 R11: ffff88811a3a9607 R12: 0000000000000001
[ 19.953709] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000
[ 19.954408] ? default_idle_call+0x2e/0x70
[ 19.954816] ? default_idle+0x1f/0x2d0
[ 19.955192] default_idle_call+0x5e/0x70
[ 19.955584] do_idle+0x3d4/0x500
[ 19.955909] ? arch_cpu_idle_exit+0x40/0x40
[ 19.956325] ? _raw_spin_unlock_irqrestore+0x23/0x30
[ 19.956829] ? trace_hardirqs_on+0x30/0x160
[ 19.957242] cpu_startup_entry+0x19/0x20
[ 19.957633] start_secondary+0x2a6/0x380
[ 19.958026] ? set_cpu_sibling_map+0x18b0/0x18b0
[ 19.958486] secondary_startup_64+0xa4/0xb0
[ 19.958921]
[ 19.959078] Allocated by task 33:
[ 19.959412] save_stack+0x1b/0x80
[ 19.959747] __kasan_kmalloc.constprop.0+0xc2/0xd0
[ 19.960222] kmem_cache_alloc+0xe4/0x230
[ 19.960617] __alloc_skb+0x91/0x510
[ 19.960967] ndisc_alloc_skb+0x133/0x330
[ 19.961358] ndisc_send_ns+0x134/0x810
[ 19.961735] addrconf_dad_work+0xad5/0xf80
[ 19.962144] process_one_work+0x78e/0x13a0
[ 19.962551] worker_thread+0x8f/0xfa0
[ 19.962919] kthread+0x2ba/0x3b0
[ 19.963242] ret_from_fork+0x3a/0x50
[ 19.963596]
[ 19.963753] Freed by task 33:
[ 19.964055] save_stack+0x1b/0x80
[ 19.964386] __kasan_slab_free+0x12f/0x180
[ 19.964830] kmem_cache_free+0x80/0x290
[ 19.965231] ip6_mc_input+0x38a/0x4d0
[ 19.965617] ipv6_rcv+0x1a4/0x1d0
[ 19.965948] __netif_receive_skb_one_core+0xf2/0x180
[ 19.966437] netif_receive_skb+0x8c/0x3c0
[ 19.966846] br_handle_frame_finish+0x779/0x1310
[ 19.967302] br_handle_frame+0x42a/0x830
[ 19.967694] __netif_receive_skb_core+0xf0e/0x2a90
[ 19.968167] __netif_receive_skb_one_core+0x96/0x180
[ 19.968658] process_backlog+0x198/0x650
[ 19.969047] net_rx_action+0x2fa/0xaa0
[ 19.969420] __do_softirq+0x268/0x7bc
[ 19.969785]
[ 19.969940] The buggy address belongs to the object at ffff888112862840
[ 19.969940] which belongs to the cache skbuff_head_cache of size 224
[ 19.971202] The buggy address is located 140 bytes inside of
[ 19.971202] 224-byte region [ffff888112862840, ffff888112862920)
[ 19.972344] The buggy address belongs to the page:
[ 19.972820] page:ffffea00044a1800 refcount:1 mapcount:0 mapping:ffff88811a2bd1c0 index:0xffff8881128625c0 compo0
[ 19.973930] flags: 0x8000000000010200(slab|head)
[ 19.974388] raw: 8000000000010200 ffff88811a2ed650 ffff88811a2ed650 ffff88811a2bd1c0
[ 19.975151] raw: ffff8881128625c0 0000000000190013 00000001ffffffff 0000000000000000
[ 19.975915] page dumped because: kasan: bad access detected
[ 19.976461] page_owner tracks the page as allocated
[ 19.976946] page last allocated via order 2, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NO)
[ 19.978332] prep_new_page+0x24b/0x330
[ 19.978707] get_page_from_freelist+0x2057/0x2c90
[ 19.979170] __alloc_pages_nodemask+0x218/0x590
[ 19.979619] new_slab+0x9d/0x300
[ 19.979948] ___slab_alloc.constprop.0+0x2f9/0x6f0
[ 19.980421] __slab_alloc.constprop.0+0x30/0x60
[ 19.980870] kmem_cache_alloc+0x201/0x230
[ 19.981269] __alloc_skb+0x91/0x510
[ 19.981620] alloc_skb_with_frags+0x78/0x4a0
[ 19.982043] sock_alloc_send_pskb+0x5eb/0x750
[ 19.982476] unix_stream_sendmsg+0x399/0x7f0
[ 19.982904] sock_sendmsg+0xe2/0x110
[ 19.983262] ____sys_sendmsg+0x4de/0x6d0
[ 19.983660] ___sys_sendmsg+0xe4/0x160
[ 19.984032] __sys_sendmsg+0xab/0x130
[ 19.984396] do_syscall_64+0xe7/0xae0
[ 19.984761] page last free stack trace:
[ 19.985142] __free_pages_ok+0x432/0xbc0
[ 19.985533] qlist_free_all+0x56/0xc0
[ 19.985907] quarantine_reduce+0x149/0x170
[ 19.986315] __kasan_kmalloc.constprop.0+0x9e/0xd0
[ 19.986791] kmem_cache_alloc+0xe4/0x230
[ 19.987182] prepare_creds+0x24/0x440
[ 19.987548] do_faccessat+0x80/0x590
[ 19.987906] do_syscall_64+0xe7/0xae0
[ 19.988276] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 19.988775]
[ 19.988930] Memory state around the buggy address:
[ 19.989402] ffff888112862780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.990111] ffff888112862800: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 19.990822] >ffff888112862880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 19.991529] ^
[ 19.992081] ffff888112862900: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.992796] ffff888112862980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Reported-by: Michael Schmidt <michael.schmidt@eti.uni-siegen.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently all usages of setup_irq() was replaced by request_irq().
request_irq() does a few sanity checks that were not done in
setup_irq(), if they fail irq registration will fail. One of the check
is to ensure that non-NULL dev_id is passed in the case of shared irq.
Fix it by passing non-NULL dev_id while registering the shared irq.
Fixes: cc2550b421 ("clocksource: Replace setup_irq() by request_irq()")
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200312064817.19000-1-afzal.mohd.ma@gmail.com
The SPICC controller in Amlogic AXG & G12A is capable of driving the
CLK/MOSI/SS signal lines through the idle state which avoid the signals
floating in unexpected state, is capable of using linear clock divider
to reach a much fine tuned range of clocks, while the old controller only
uses a power of two clock divider, result at a more coarse clock range and
finally is capable of running at 80M clock.
The SPICC controller in Amlogic G12A takes the source clock from a specific
clock instead of the bus clock and has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants. Thus
the burst management is simplified and takes in account a variable FIFO
size.
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Neil Armstrong (7):
spi: meson-spicc: remove unused variables
spi: meson-spicc: support max 80MHz clock
spi: meson-spicc: add min sclk for each compatible
spi: meson-spicc: setup IO line delay
spi: meson-spicc: adapt burst handling for G12A support
dt-bindings: spi: amlogic,meson-gx-spicc: add Amlogic G12A compatible
spi: meson-spicc: add support for Amlogic G12A
Sunny Luo (2):
spi: meson-spicc: enhance output enable feature
spi: meson-spicc: add a linear clock divider support
.../bindings/spi/amlogic,meson-gx-spicc.yaml | 22 +
drivers/spi/Kconfig | 1 +
drivers/spi/spi-meson-spicc.c | 496 +++++++++++++-----
3 files changed, 392 insertions(+), 127 deletions(-)
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-amlogic
to_spi_device() already checks 'dev'. No need to do it before calling
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200312134507.10000-1-wsa@the-dreams.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The Amlogic G12A SPICC controllers uses a secondary clock used to feed the
baud rate generator and the delay control logic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-9-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the SPICC controllers on the Amlogic G12A SoCs family.
The G12A SPICC controllers inherit from the AXG enhanced registers but
takes an external pclk for the baud rate generator and can achieve up to
166MHz SCLK.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-10-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The G12A SPICC controller variant has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants.
Thus simplify the burst management and take in account a variable FIFO
size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-8-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-7-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The G12A SPICC controller variant takes the source clock from a specific
clock instead of the bus clock.
The minimal clock calculus won't work with the G12A support, thus add the
minimal supported clock for each variant and pass this to the SPI core.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-6-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG is capable of running at 80M clock.
The ASIC IP is improved and the clock is actually running higher than
previous old SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-5-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.
Also convert the clock registration into Common Clock Framework.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-4-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG is capable of driving the CLK/MOSI/SS
signal lines through the idle state (between two transmission operation),
which avoid the signals floating in unexpected state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-3-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kryo280 is found in msm8998, so add it to the list of cpu compatibles.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The call to platform_get_irq() was changed to print a log if the
interrupt was not available, and that was causing bogus messages to spew
out for the IPMI driver. People have requested that this get in to 5.6
so I'm sending it along.
-----BEGIN PGP SIGNATURE-----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=W5WC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fix from Corey Minyard:
"Fix a message spew on some system
The call to platform_get_irq() was changed to print a log if the
interrupt was not available, and that was causing bogus messages to
spew out for the IPMI driver. People have requested that this get in
to 5.6 so I'm sending it along"
* tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi:
ipmi_si: Avoid spurious errors for optional IRQs
Function soc_tplg_dbytes_create(), calls soc_tplg_init_kcontrol() to
perform additional driver specific initialization. While
soc_tplg_init_kcontrol() ensures that component is valid before invoking
ops->control_load, there is no such check at the end of
soc_tplg_dbytes_create() where list_add() is used.
Also in quite a few places, there is reference of tplg->comp->dapm or
tplg->comp->card, without any checks for tplg->comp.
In consequence of the above this may lead to referencing NULL pointer.
This allows for removal of now unnecessary checks.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20200312122239.14489-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit mentioned below added a stray plus sign, likely
due to some conflict resolution (i.e. as a leftover from a
unified diff), which was harmless since it was just used as
an integer constant modifier. Remove it anyway, now that I
stumbled across it.
Fixes: cf33a7728b ("wlcore: mesh: Add support for RX Broadcast Key")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The might_sleep() in do_con_write() is redundant because console_lock()
already contains might_sleep(). Remove it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224073450.292892-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as Intel Ice Lake TCSS (Type-C Subsystem) the Tiger Lake
TCSS xHCI needs to be runtime suspended whenever possible to allow the
TCSS hardware block to enter D3cold and thus save energy.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on the current link state the steps to resume the link to U0
varies. The normal case when a port is suspended (U3) we set the link
to U0 and wait for a port event when U3exit completed and port moved to
U0.
If the port is in U1/U2, then no event is issued, just set link to U0
If port is in Resume or Recovery state then the device has already
initiated resume, and this host initiated resume is racing against it.
Port event handler for device initiated resume will set link to U0,
just wait for the port to reach U0 before returning.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like U3 case, xHCI spec doesn't specify the upper bound of U0 transition
time. The 20ms is not enough for some devices.
Intead of polling PLS or PLC, we can facilitate the port change event to
know that the link transits to U0 is completed.
While at it, also separate U0 and U3 case to make the code cleaner.
[variable rename to u3exit, and skip completion for usb2 ports -Mathias ]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI spec doesn't specify the upper bound of U3 transition time. For
some devices 20ms is not enough, so we need to make sure the link state
is in U3 before further actions.
I've tried to use U3 Entry Capability by setting U3 Entry Enable in
config register, however the port change event for U3 transition
interrupts the system suspend process.
For now let's use the less ideal method by polling PLS.
[use usleep_range(), and shorten the delay time while polling -Mathias]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This PCIe controller chip is used on the Raspberry Pi 4 and multiple
adapter cards. There is no publicly available documentation for the
chip, yet both the downstream RPi4 kernel and the controller cards
support/advertise LPM support.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Additional debugging to show xHC USBSTS register when stop endpoint
command watchdog triggers and host is assumed dead.
useful to know the current status before the controller is stopped by
the xhci driver and everything is released and freed.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't show the same error message for transaction errors and split
transaction errors. It's very confusing while debugging.
Transaction errors are often due to electrical interference.
Split transaction errors are about xHC not being able to
schedule start and complete split transactions needed to address
low- and full-speed devices behind high-speed hubs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
10-bit and 12-bit greyscale input data to the CSI can be written as
8-bit data to memory. Support this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
10-bit and 12-bit greyscale input data to the CSI can be written as
8-bit data to memory. Support this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
