Commit graph

1,058,063 commits

Author SHA1 Message Date
Nadav Amit
fe6d269d0e iommu/amd: Tailored gather logic for AMD
AMD's IOMMU can flush efficiently (i.e., in a single flush) any range.
This is in contrast, for instnace, to Intel IOMMUs that have a limit on
the number of pages that can be flushed in a single flush.  In addition,
AMD's IOMMU do not care about the page-size, so changes of the page size
do not need to trigger a TLB flush.

So in most cases, a TLB flush due to disjoint range is not needed for
AMD. Yet, vIOMMUs require the hypervisor to synchronize the virtualized
IOMMU's PTEs with the physical ones. This process induce overheads, so
it is better not to cause unnecessary flushes, i.e., flushes of PTEs
that were not modified.

Implement and use amd_iommu_iotlb_gather_add_page() and use it instead
of the generic iommu_iotlb_gather_add_page(). Ignore disjoint regions
unless "non-present cache" feature is reported by the IOMMU
capabilities, as this is an indication we are running on a physical
IOMMU. A similar indication is used by VT-d (see "caching mode"). The
new logic retains the same flushing behavior that we had before the
introduction of page-selective IOTLB flushes for AMD.

On virtualized environments, check if the newly flushed region and the
gathered one are disjoint and flush if it is.

Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Jiajun Cao <caojiajun@vmware.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20210723093209.714328-6-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2021-08-02 11:26:05 +02:00
Nadav Amit
febb82c208 iommu: Factor iommu_iotlb_gather_is_disjoint() out
Refactor iommu_iotlb_gather_add_page() and factor out the logic that
detects whether IOTLB gather range and a new range are disjoint. To be
used by the next patch that implements different gathering logic for
AMD.

Note that updating gather->pgsize unconditionally does not affect
correctness as the function had (and has) an invariant, in which
gather->pgsize always represents the flushing granularity of its range.
Arguably, “size" should never be zero, but lets assume for the matter of
discussion that it might.

If "size" equals to "gather->pgsize", then the assignment in question
has no impact.

Otherwise, if "size" is non-zero, then iommu_iotlb_sync() would
initialize the size and range (see iommu_iotlb_gather_init()), and the
invariant is kept.

Otherwise, "size" is zero, and "gather" already holds a range, so
gather->pgsize is non-zero and (gather->pgsize && gather->pgsize !=
size) is true. Therefore, again, iommu_iotlb_sync() would be called and
initialize the size.

Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jiajun Cao <caojiajun@vmware.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20210723093209.714328-5-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2021-08-02 11:26:05 +02:00
Robin Murphy
3136895cc5 iommu: Improve iommu_iotlb_gather helpers
The Mediatek driver is not the only one which might want a basic
address-based gathering behaviour, so although it's arguably simple
enough to open-code, let's factor it out for the sake of cleanliness.
Let's also take this opportunity to document the intent of these
helpers for clarity.

Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Jiajun Cao <caojiajun@vmware.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20210723093209.714328-4-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2021-08-02 11:26:05 +02:00
Nadav Amit
6664340cf1 iommu/amd: Do not use flush-queue when NpCache is on
Do not use flush-queue on virtualized environments, where the NpCache
capability of the IOMMU is set. This is required to reduce
virtualization overheads.

This change follows a similar change to Intel's VT-d and a detailed
explanation as for the rationale is described in commit 29b3283972
("iommu/vt-d: Do not use flush-queue when caching-mode is on").

Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Jiajun Cao <caojiajun@vmware.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20210723093209.714328-3-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2021-08-02 11:26:05 +02:00
Nadav Amit
fc65d0acaf iommu/amd: Selective flush on unmap
Recent patch attempted to enable selective page flushes on AMD IOMMU but
neglected to adapt amd_iommu_iotlb_sync() to use the selective flushes.

Adapt amd_iommu_iotlb_sync() to use selective flushes and change
amd_iommu_unmap() to collect the flushes. As a defensive measure, to
avoid potential issues as those that the Intel IOMMU driver encountered
recently, flush the page-walk caches by always setting the "pde"
parameter. This can be removed later.

Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Jiajun Cao <caojiajun@vmware.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20210723093209.714328-2-namit@vmware.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
2021-08-02 11:26:05 +02:00
Colin Ian King
85b1ebfea2 interconnect: Fix undersized devress_alloc allocation
The expression sizeof(**ptr) for the void **ptr is just 1 rather than
the size of a pointer. Fix this by using sizeof(*ptr).

Addresses-Coverity: ("Wrong sizeof argument")
Fixes: e145d9a184 ("interconnect: Add devm_of_icc_get() as exported API for users")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210730075408.19945-1-colin.king@canonical.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
2021-08-02 12:25:00 +03:00
Cong Wang
695176bfe5 net_sched: refactor TC action init API
TC action ->init() API has 10 parameters, it becomes harder
to read. Some of them are just boolean and can be replaced
by flags. Similarly for the internal API tcf_action_init()
and tcf_exts_validate().

This patch converts them to flags and fold them into
the upper 16 bits of "flags", whose lower 16 bits are still
reserved for user-space. More specifically, the following
kernel flags are introduced:

TCA_ACT_FLAGS_POLICE replace 'name' in a few contexts, to
distinguish whether it is compatible with policer.

TCA_ACT_FLAGS_BIND replaces 'bind', to indicate whether
this action is bound to a filter.

TCA_ACT_FLAGS_REPLACE  replaces 'ovr' in most contexts,
means we are replacing an existing action.

TCA_ACT_FLAGS_NO_RTNL replaces 'rtnl_held' but has the
opposite meaning, because we still hold RTNL in most
cases.

The only user-space flag TCA_ACT_FLAGS_NO_PERCPU_STATS is
untouched and still stored as before.

I have tested this patch with tdc and I do not see any
failure related to this patch.

Tested-by: Vlad Buslov <vladbu@nvidia.com>
Acked-by: Jamal Hadi Salim<jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02 10:24:38 +01:00
Martin Kaiser
451395f798 niu: read property length only if we use it
In three places, the driver calls of_get_property and reads the property
length although the length is not used. Update the calls to not request
the length.

Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02 10:24:07 +01:00
Jakub Sitnicki
d51c5907e9 net, gro: Set inner transport header offset in tcp/udp GRO hook
GSO expects inner transport header offset to be valid when
skb->encapsulation flag is set. GSO uses this value to calculate the length
of an individual segment of a GSO packet in skb_gso_transport_seglen().

However, tcp/udp gro_complete callbacks don't update the
skb->inner_transport_header when processing an encapsulated TCP/UDP
segment. As a result a GRO skb has ->inner_transport_header set to a value
carried over from earlier skb processing.

This can have mild to tragic consequences. From miscalculating the GSO
segment length to triggering a page fault [1], when trying to read TCP/UDP
header at an address past the skb->data page.

The latter scenario leads to an oops report like so:

  BUG: unable to handle page fault for address: ffff9fa7ec00d008
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD 123f201067 P4D 123f201067 PUD 123f209067 PMD 0
  Oops: 0000 [#1] SMP NOPTI
  CPU: 44 PID: 0 Comm: swapper/44 Not tainted 5.4.53-cloudflare-2020.7.21 #1
  Hardware name: HYVE EDGE-METAL-GEN10/HS-1811DLite1, BIOS V2.15 02/21/2020
  RIP: 0010:skb_gso_transport_seglen+0x44/0xa0
  Code: c0 41 83 e0 11 f6 87 81 00 00 00 20 74 30 0f b7 87 aa 00 00 00 0f [...]
  RSP: 0018:ffffad8640bacbb8 EFLAGS: 00010202
  RAX: 000000000000feda RBX: ffff9fcc8d31bc00 RCX: ffff9fa7ec00cffc
  RDX: ffff9fa7ebffdec0 RSI: 000000000000feda RDI: 0000000000000122
  RBP: 00000000000005c4 R08: 0000000000000001 R09: 0000000000000000
  R10: ffff9fe588ae3800 R11: ffff9fe011fc92f0 R12: ffff9fcc8d31bc00
  R13: ffff9fe0119d4300 R14: 00000000000005c4 R15: ffff9fba57d70900
  FS:  0000000000000000(0000) GS:ffff9fe68df00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: ffff9fa7ec00d008 CR3: 0000003e99b1c000 CR4: 0000000000340ee0
  Call Trace:
   <IRQ>
   skb_gso_validate_network_len+0x11/0x70
   __ip_finish_output+0x109/0x1c0
   ip_sublist_rcv_finish+0x57/0x70
   ip_sublist_rcv+0x2aa/0x2d0
   ? ip_rcv_finish_core.constprop.0+0x390/0x390
   ip_list_rcv+0x12b/0x14f
   __netif_receive_skb_list_core+0x2a9/0x2d0
   netif_receive_skb_list_internal+0x1b5/0x2e0
   napi_complete_done+0x93/0x140
   veth_poll+0xc0/0x19f [veth]
   ? mlx5e_napi_poll+0x221/0x610 [mlx5_core]
   net_rx_action+0x1f8/0x790
   __do_softirq+0xe1/0x2bf
   irq_exit+0x8e/0xc0
   do_IRQ+0x58/0xe0
   common_interrupt+0xf/0xf
   </IRQ>

The bug can be observed in a simple setup where we send IP/GRE/IP/TCP
packets into a netns over a veth pair. Inside the netns, packets are
forwarded to dummy device:

  trafgen -> [veth A]--[veth B] -forward-> [dummy]

For veth B to GRO aggregate packets on receive, it needs to have an XDP
program attached (for example, a trivial XDP_PASS). Additionally, for UDP,
we need to enable GSO_UDP_L4 feature on the device:

  ip netns exec A ethtool -K AB rx-udp-gro-forwarding on

The last component is an artificial delay to increase the chances of GRO
batching happening:

  ip netns exec A tc qdisc add dev AB root \
     netem delay 200us slot 5ms 10ms packets 2 bytes 64k

With such a setup in place, the bug can be observed by tracing the skb
outer and inner offsets when GSO skb is transmitted from the dummy device:

tcp:

FUNC              DEV   SKB_LEN  NH  TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output  dumB     2830 270 290   1 294 254     1383 (tcpv4,gre,)
                                                ^^^
udp:

FUNC              DEV   SKB_LEN  NH  TH ENC INH ITH GSO_SIZE GSO_TYPE
ip_finish_output  dumB     2818 270 290   1 294 254     1383 (gre,udp_l4,)
                                                ^^^

Fix it by updating the inner transport header offset in tcp/udp
gro_complete callbacks, similar to how {inet,ipv6}_gro_complete callbacks
update the inner network header offset, when skb->encapsulation flag is
set.

[1] https://lore.kernel.org/netdev/CAKxSbF01cLpZem2GFaUaifh0S-5WYViZemTicAg7FCHOnh6kug@mail.gmail.com/

Fixes: bf296b125b ("tcp: Add GRO support")
Fixes: f993bc25e5 ("net: core: handle encapsulation offloads when computing segment lengths")
Fixes: e20cf8d3f1 ("udp: implement GRO for plain UDP sockets.")
Reported-by: Alex Forster <aforster@cloudflare.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02 10:20:56 +01:00
Prabhakar Kushwaha
1159e25c13 qede: fix crash in rmmod qede while automatic debug collection
A crash has been observed if rmmod is done while automatic debug
collection in progress. It is due to a race  condition between
both of them.

To fix stop the sp_task during unload to avoid running qede_sp_task
even if they are schedule during removal process.

Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-02 10:17:24 +01:00
Daniel Vetter
2f425cf524 drm: Fix oops in damage self-tests by mocking damage property
I've added a new check to make sure that drivers which insepct the
damage property have it set up correctly, but somehow missed that this
borke the damage selftest in the CI result noise.

Fix it up by mocking enough of drm_device and drm_plane so we can call
drm_plane_enable_fb_damage_clips() to make the new check happy.

Since there's a lot of duplicated mock code already copy-pasted into
each test I've also refactored this a bit to trim it down.

v2: Squash in fixup from 0day for

drivers/gpu/drm/selftests/test-drm_damage_helper.c:15:19: warning: symbol 'mock_device' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:16:30: warning: symbol 'mock_obj_props' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:17:18: warning: symbol 'mock_plane' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:18:21: warning: symbol 'mock_prop' was not declared. Should it be static?

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>

Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Fixes: c7fcbf2513 ("drm/plane: check that fb_damage is set up when used")
Cc: José Roberto de Souza <jose.souza@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730095251.4343-1-daniel.vetter@ffwll.ch
Link: https://patchwork.freedesktop.org/patch/msgid/20210730141948.GA11955@243d74413310
2021-08-02 11:15:11 +02:00
Cai Huoqing
0ae865ef92 drm: Fix typo in comments
fix typo for drm

v1->v2:
respin with the change "iff ==> implies that"

Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730132729.376-1-caihuoqing@baidu.com
2021-08-02 10:19:43 +02:00
Linus Walleij
ec343111c0 mfd: db8500-prcmu: Adjust map to reality
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.

Drop some whitespace at the same time.

Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2021-08-02 08:45:36 +01:00
Andre Przywara
614e1bb530 dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ)
The AXP305 PMIC used on many boards with the H616 SoC seems to be fully
compatible to the AXP805 PMIC, so add the proper chain of compatible
strings.

Also at least on one board (Orangepi Zero2) there is no interrupt line
connected to the CPU, so make the "interrupts" property optional.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2021-08-02 08:40:07 +01:00
Simon Ser
33e1fc0624 drm/connector: add ref to drm_connector_get in iter docs
Mention that connectors need to be referenced manually if they are
to be accessed after the iteration has progressed or ended.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/KRoUI7OC9lRIvk3YzdGm6tcMVAVlG1fR78Ll7kTZZT4@cp3-web-051.plabs.ch
2021-08-02 09:34:38 +02:00
Takashi Iwai
a39978ed6d ALSA: doc: Add the description of quirk_flags option for snd-usb-audio
Just briefly described about the new option.

Link: https://lore.kernel.org/r/20210729074404.19728-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:08 +02:00
Takashi Iwai
5b51785442 ALSA: usb-audio: Add quirk_flags module option
This patch adds a new module option, quirk_flags, for allowing user to
try some additional device-specific quirk behavior more easily.
When this option is set to non-zero, it overrides the quirk_flags, and
the specific workaround is applied.

Link: https://lore.kernel.org/r/20210729074404.19728-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:07 +02:00
Takashi Iwai
68e851ee4c ALSA: usb-audio: Move generic DSD raw detection into quirk_flags
The generic DSD raw detection is based on the known allow list, and we
can integrate it into quirk_flags, too.

Link: https://lore.kernel.org/r/20210729074404.19728-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:07 +02:00
Takashi Iwai
3c69dc9134 ALSA: usb-audio: Move ignore_ctl_error check into quirk_flags
The mixer code has a flag ignore_ctl_error for ignoring the errors
returned from the device wrt mixer accesses, and this is set from the
entries in mixer_maps.c, as well as ignore_ctl_error module option.
Those can be well integrated into the new quirk_flags field, too.

Link: https://lore.kernel.org/r/20210729074404.19728-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:05 +02:00
Takashi Iwai
44e6fc64df ALSA: usb-audio: Move autosuspend quirk into quirk_flags
The auto-suspend suppression workaround for Lenovo machines are
handled in quirks-table.h.  Now it's more easier to handle with
quirk_flags.

Link: https://lore.kernel.org/r/20210729074404.19728-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:04 +02:00
Takashi Iwai
8bfe17ad97 ALSA: usb-audio: Move rate validation quirk into quirk_flags
The rate validation at the device probe is applied only to the
specific devices (currently only for MOTU devices), and this check can
be moved to quirk_flags gracefully, too.

Link: https://lore.kernel.org/r/20210729074404.19728-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:03 +02:00
Takashi Iwai
1f074fe569 ALSA: usb-audio: Move interface setup delay into quirk_flags
Yet another delay is applied at switching the interface.  This can be
moved to quirk_flags, too.

Link: https://lore.kernel.org/r/20210729073855.19043-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:02 +02:00
Takashi Iwai
f748385471 ALSA: usb-audio: Move control message delay quirk into quirk_flags
We apply some delay for the control messages on certain devices as a
workaround, and this can be moved into the quirk_flags as well.
Currently there are three different delay periods (1ms, 5ms and 20ms),
so three different quirk bits are assigned for them.

Link: https://lore.kernel.org/r/20210729073855.19043-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:01 +02:00
Takashi Iwai
2de00d5a91 ALSA: usb-audio: Move ITF-USB DSD quirk handling into quirk_flags
The devices with ITF-USB DSD type are listed in another function, and
this can be integrated into the quirk_flags easily.

Link: https://lore.kernel.org/r/20210729073855.19043-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:06:00 +02:00
Takashi Iwai
f21dca857b ALSA: usb-audio: Move clock setup quirk into quirk_flags
There are a couple of device-specific quirks in the clock setup code,
and those can be moved gracefully to quirk_flags, too.

Link: https://lore.kernel.org/r/20210729073855.19043-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:59 +02:00
Takashi Iwai
019c7f912c ALSA: usb-audio: Move playback_first flag into quirk_flags
The snd_usb_audio.playback_first flag is used by the implicit feedback
mode handling, and this can be also moved to quirk_flags.

Link: https://lore.kernel.org/r/20210729073855.19043-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:58 +02:00
Takashi Iwai
c1b034a421 ALSA: usb-audio: Move tx_length quirk handling to quirk_flags
There is another quirk for the transfer, and that's currently specific
to Zoom R16/24, handled in create_standard_audio_quirk().  Let's move
this also to the new quirk_flags.

Link: https://lore.kernel.org/r/20210729073855.19043-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:57 +02:00
Takashi Iwai
af158a7f8d ALSA: usb-audio: Move txfr_quirk handling to quirk_flags
The txfr_quirk field was meant for aligning the transfer, and it's set
for certain devices in quirks-table.h.  Now we can move that stuff
also to the new quirk_flags gracefully, and reduce the quirks-table.h
entries (that are exposed to module device table).

As the quirks-table.h entries are also with the name string override,
provide the corresponding entries to the usb_audio_names[] table,
too.

Link: https://lore.kernel.org/r/20210729073855.19043-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:56 +02:00
Takashi Iwai
ce47d47e5c ALSA: usb-audio: Move media-controller API quirk into quirk_flags
The devices that can have media-controller API entries are currently
specified via tables in quirks-table.h, as a part of descriptor
override.  This can fit better to the new quirk_flags, as we just need
a matching with the given ID and create the MC entries accordingly.

Link: https://lore.kernel.org/r/20210729073855.19043-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:54 +02:00
Takashi Iwai
4d4dee0aef ALSA: usb-audio: Introduce quirk_flags field
As more and more device-specific workarounds came up and gathered in
various places, it becomes harder to manage.  Now it's time to clean
up and collect workarounds more consistently and make them more easily
applicable.

This patch is the first step for that: a new field quirk_flags is
introduced in snd_usb_audio struct to contain the bit flags for
various device-specific quirks.  Those are separate one from the
quirks in quirks-table.h; the quirks-table.h entries are for more
intrusive stuff that needs the descriptor override, while the new
quirk_flags is for easier ones that are tied with the vendor:product
IDs.

In this patch, as the first example, we convert the list of devices
and vendors to ignore GET_SAMPLE_RATE, formerly defined in
snb_usb_get_sample_rate_quirk().

Link: https://lore.kernel.org/r/20210729073855.19043-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:05:53 +02:00
Christophe JAILLET
e9c5b0b53c dmaengine: idxd: Fix a possible NULL pointer dereference
'device_driver_attach()' dereferences its first argument (i.e. 'alt_drv')
so it must not be NULL.
Simplify the error handling logic about NULL 'alt_drv' in order to be
more robust and future-proof.

Fixes: 568b212646 ("dmaengine: idxd: fix uninit var for alt_drv")
Fixes: 6e7f3ee97b ("dmaengine: idxd: move dsa_drv support to compatible mode")

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/77f0dc4f3966591d1f0cffb614a94085f8895a85.1627560174.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:35:10 +05:30
Takashi Iwai
01099b1ad9 Merge branch 'for-linus' into for-next 2021-08-02 09:04:48 +02:00
Vinod Koul
ffa179ae2a Merge branch 'fixes' into next 2021-08-02 12:34:48 +05:30
Takashi Iwai
eda80d7c9c ALSA: memalloc: Fix regression with SNDRV_DMA_TYPE_CONTINUOUS
The recent code refactoring made the mmap of continuous pages to be
done via the own helper snd_dma_continuous_mmap() with
remap_pfn_range().  There I overlooked that dmab->addr isn't set for
the allocation with SNDRV_DMA_TYPE_CONTINUOUS.  This resulted always
in an error at mmap with this buffer type on the system such as
Intel SST Baytrail driver.

This patch fixes the regression by passing the correct address.

Fixes: 30b7ba6972 ("ALSA: core: Add continuous and vmalloc mmap ops")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/8d6674da-7d7b-803e-acc9-7de6cb1223fa@redhat.com
Link: https://lore.kernel.org/r/20210801113801.31290-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-08-02 09:03:22 +02:00
Juergen Borleis
7199ddede9 dmaengine: imx-dma: configure the generic DMA type to make it work
Commit dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config
direction usage") changes the method from a "configuration when called"
to an "configuration when used". Due to this, only the cyclic DMA type
gets configured correctly, while the generic DMA type is left
non-configured.

Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Fixes: dea7a9fbb0 ("dmaengine: imx-dma: remove dma_slave_config direction usage")
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:31:19 +05:30
Juergen Borleis
dd861267bf dma: imx-dma: configure the generic DMA type to make it work
Commit dea7a9f
  dmaengine: imx-dma: remove dma_slave_config direction usage

changes the method from a "configuration when called" to an "configuration
when used". Due to this, only the cyclic DMA type gets configured
correctly, while the generic DMA type is left non-configured.

Without this additional call, the struct imxdma_channel::word_size member
is stuck at DMA_SLAVE_BUSWIDTH_UNDEFINED and imxdma_prep_slave_sg() always
returns NULL.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Link: https://lore.kernel.org/r/20210729071821.9857-1-jbe@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:30:39 +05:30
Alexander Sverdlin
b92e83f7c4 dmaengine: ep93xx: Prepare clock before using it
Use clk_prepare_enable()/clk_disable_unprepare() in preparation for switch
to Common Clock Framework, otherwise the following is visible:

WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:1011 clk_core_enable+0x9c/0xbc
Enabling unprepared m2p0
...
Hardware name: Cirrus Logic EDB9302 Evaluation Board
...
clk_core_enable
clk_core_enable_lock
ep93xx_dma_alloc_chan_resources
dma_chan_get
find_candidate
__dma_request_channel
snd_dmaengine_pcm_request_channel
dmaengine_pcm_new
snd_soc_pcm_component_new
soc_new_pcm
snd_soc_bind_card
edb93xx_probe
...
ep93xx-i2s ep93xx-i2s: Missing dma channel for stream: 0
ep93xx-i2s ep93xx-i2s: ASoC: error at snd_soc_pcm_component_new on ep93xx-i2s: -22
edb93xx-audio edb93xx-audio: ASoC: can't create pcm CS4271 HiFi :-22
edb93xx-audio edb93xx-audio: snd_soc_register_card() failed: -22
edb93xx-audio: probe of edb93xx-audio failed with error -22

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210726140001.24820-6-nikita.shubin@maquefel.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:27:10 +05:30
Pandith N
c454d16a7d dmaengine: dw-axi-dmac: Burst length settings
Burst length, DMA HW capability set in dt-binding is now used in driver.

Signed-off-by: Pandith N <pandith.n@intel.com>
Tested-by: Pan Kris <kris.pan@intel.com>
Link: https://lore.kernel.org/r/20210802055454.15192-4-pandith.n@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:19:52 +05:30
Pandith N
f95f3b5351 dmaengine: dw-axi-dmac: support parallel memory <--> peripheral transfers
Added support for multiple DMA_MEM_TO_DEV, DMA_DEV_TO_MEM transfers in
parallel. This is required for peripherals using DMA for transmit and
receive operations at the same time. APB slot number needs to be
programmed in channel hardware handshaking interface

Signed-off-by: Pandith N <pandith.n@intel.com>
Tested-by: Pan Kris <kris.pan@intel.com>
Link: https://lore.kernel.org/r/20210802055454.15192-3-pandith.n@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:19:52 +05:30
Pandith N
32286e2793 dmaengine: dw-axi-dmac: Remove free slot check algorithm in dw_axi_dma_set_hw_channel
Removed free slot check algorithm in dw_axi_dma_set_hw_channel. For 8
DMA channels, use respective handshake slot in DMA_HS_SEL APB register.

For every channel, an dedicated slot is provided in  hardware handshake
register AXIDMA_CTRL_DMA_HS_SEL_n. Peripheral source number is
programmed in respective channel slots.

Signed-off-by: Pandith N <pandith.n@intel.com>
Tested-by: Pan Kris <kris.pan@intel.com>
Link: https://lore.kernel.org/r/20210802055454.15192-2-pandith.n@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:19:51 +05:30
Jordy Zomer
5eea6c9712 dmaengine: usb-dmac: make usb_dmac_get_current_residue unsigned
The usb_dmac_get_current_residue function used to
take a signed integer as a pos parameter.
The only callers of this function passes an unsigned integer to it.
Therefore to make it obviously safe, let's just make this an unsgined
integer as this is used in pointer arithmetics.

Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210731091939.510816-1-jordy@pwning.systems
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 12:16:47 +05:30
Pierre-Louis Bossart
dd81e7c3f0 soundwire: cadence: override PDI configurations to create loopback
When we set a source PDI, the target PDI parameters will be overridden
by the source register values. The loopback streams can be
independently enabled on each link.

While the loopback source and target can be configured before any
stream is active on each link, the loopback stream should only be
prepared/triggered when the playback stream is prepared. Otherwise all
registers might be programmed to their reset values and the loopback
will not succeed. The SoundWire bus driver currently does not allow
two streams to be triggered at the same time, so the playback will
have to be started first, and later the loopback.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Pierre-Louis Bossart
8fba8acd39 soundwire: cadence: add debugfs interface for PDI loopbacks
For debug, it's interesting to create a loopback stream for each link
and use debugfs to set a source and target PDI. The target PDI would
need to be an RX port and use the same register configurations as the
source PDI. This capability allows e.g. for the headphone playback
stream to be snooped on the headset capture stream, or alternatively
for the addition of a dedicated loopback stream, in addition of
regular capture for that link.

This patch only adds the debugfs part, the port/PDI handling will be
handled in the next patches.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Bard Liao
24f08b3aa5 soundwire: stream: don't program mockup device ports
Mockup devices don't take part in command/control operations and their
virtual ports shall not be programmed.

Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Pierre-Louis Bossart
7fae3cfb70 soundwire: bus: squelch error returned by mockup devices
All read and writes from/to SoundWire mockup devices will return
-ENODATA/Command_Ignored, this patch forces a Command_OK result to let
the bus perform the required configurations, e.g. for the Data Ports,
which will only have an effect on the Master side.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Pierre-Louis Bossart
4a7a603cad soundwire: add flag to ignore all command/control for mockup devices
SoundWire mockup devices don't take part in the command/control
protocol, so all commands will complete with -ENODATA or
Command_Ignored results. With a flag, we can suppress such errors in
the bus management and make it appear as if all read/writes succeed.

Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Bard Liao
e6645314eb soundwire: stream: don't abort bank switch on Command_Ignored/-ENODATA
This change is needed for support of mockup devices, which by
construction will not provide any answer to a bank switch, but it's
also legit for regular cases.

If for some reason a device loses sync and cannot handle a bank
switch, we should go ahead anyways. The devices can always resync
later.

The only case where the error flow should be used is when there is a
Command_Aborted composite answer from SoundWire devices.

Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 11:08:22 +05:30
Vinod Koul
13a5635632 ASoC: Add mockup SoundWire CODEC
Useful for bringup testing, not for production usage.
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmDvOcIACgkQJNaLcl1U
 h9ArJAf/fc5v395MVeoWqQhXNaKj7oA3UBQ+ML0X4uW+xdbzQ6gcejxvneu9dw+S
 FEZ7BD9Zg4tQcAaG3NT/KR71Lkkv0yOMdgt4uDAXruxCLJWU+sZH3fonHh2oYSXt
 Ro1vLjTA7vjznyfche1HpdgUPajgL8+ry6z3J0W/JEP7LVIjVvIxy3zgqM7BrVD2
 hb818UTm3G6GMJq9C86D1OUbznnkAgw9Z6xt3ibITYUwaj1w3PfQLL2JDugUi8dX
 nubDu4TDQ3GYSxsqP5B+Gzmwk0v19E7ZrXR/bTHZGQdSJlg1Ss2bf/vRlq0Lq5kn
 j73Bqp9ttvZFkyyOguJVR9FeGyFApA==
 =lvJ1
 -----END PGP SIGNATURE-----

Merge tag 'asoc-sdw-mockup-codec' into next

ASoC: Add mockup SoundWire CODEC

Useful for bringup testing, not for production usage.
2021-08-02 10:32:51 +05:30
Pierre-Louis Bossart
ff560946ef soundwire: cadence: add paranoid check on self-clearing bits
The Cadence IP exposes a small number of self-clearing bits in
the MCP_CONTROL and MCP_CONFIG_UPDATE registers.

We currently do not check that those bits are indeed cleared,
e.g. during resume operations. That could lead to resuming peripheral
devices too early.

In addition, if we happen to read these registers, update one of the
fields and write the register back, we may be writing stale data that
might have been cleared in hardware. These sort of race conditions
could lead to e.g. doing a hw_reset twice or stopping a clock that
just restarted. There is no clear way of avoiding these potential race
conditions other than making sure that these registers fields are
cleared before any read-modify-write sequence. If we detect this sort
of errors, we only log them since there is no clear recovery
possible. The only way out is likely to restart the IP with a
suspend/resume cycle.

Note that the checks are performed before updating the registers, as
well as after the Intel 'sync go' sequence in multi-link mode. That
should cover both the start and end of suspend/resume hardware
configurations. The Multi-Master mode gates the configuration updates
until the 'sync go' signal is asserted, so we only check on init and
after the end of the 'sync go' sequence.

The duration of the usleep_range() was defined by the GSYNC frequency
used in multi-master mode. With a 4kHz frequency, any configuration
change might be deferred by up to 250us. Extending the range to
1000-1500us should guarantee that the configuration change is
completed without any significant impact on the overall resume
time.

Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714051349.13064-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
2021-08-02 09:19:45 +05:30
Linus Torvalds
c500bee1c5 Linux 5.14-rc4 v5.14-rc4 2021-08-01 17:04:17 -07:00