devm_of_qcom_ice_get() currently returns NULL if ICE SCM is not available
or "qcom,ice" property is not found in DT. But this confuses the clients
since NULL doesn't convey the reason for failure. So return proper error
codes instead of NULL.
Reported-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Sumit Garg <sumit.garg@oss.qualcomm.com> # OP-TEE as TZ
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-qcom-ice-fix-v7-3-2a595382185b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
By the time the consumer driver calls devm_of_qcom_ice_get(), all the
platform devices for ICE nodes would've been created by
of_platform_default_populate().
So for the absence of any platform device, -ENODEV should not returned, not
-EPROBE_DEFER.
Fixes: 2afbf43a4a ("soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver")
Tested-by: Sumit Garg <sumit.garg@oss.qualcomm.com> # OP-TEE as TZ
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-qcom-ice-fix-v7-2-2a595382185b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The current platform driver design causes probe ordering races with
consumers (UFS, eMMC) due to ICE's dependency on SCM firmware calls. If ICE
probe fails (missing ICE SCM or DT registers), devm_of_qcom_ice_get() loops
with -EPROBE_DEFER, leaving consumers non-functional even when ICE should
be gracefully disabled. devm_of_qcom_ice_get() doesn't know if the ICE
driver probe has failed due to above reasons or it is waiting for the SCM
driver.
Moreover, there is no devlink dependency between ICE and consumer drivers
as 'qcom,ice' is not considered as a DT 'supplier'. So the consumer drivers
have no idea of when the ICE driver is going to probe.
To address these issues, store the error pointer in a global xarray with
ice node phandle as a key during probe in addition to the valid ice pointer
and synchronize both qcom_ice_probe() and of_qcom_ice_get() using a mutex.
If the xarray entry is NULL, then it implies that the driver is not
probed yet, so return -EPROBE_DEFER. If it has any error pointer, return
that error pointer directly. Otherwise, add the devlink as usual and return
the valid pointer to the consumer.
Xarray is used instead of platform drvdata, since driver core frees the
drvdata during probe failure. So it cannot be used to pass the error
pointer to the consumers.
Note that this change only fixes the standalone ICE DT node bindings and
not the ones with 'ice' range embedded in the consumer nodes, where there
is no issue.
Fixes: 2afbf43a4a ("soc: qcom: Make the Qualcomm UFS/SDCC ICE a dedicated driver")
Reported-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Tested-by: Sumit Garg <sumit.garg@oss.qualcomm.com> # OP-TEE as TZ
Acked-by: Sumit Garg <sumit.garg@oss.qualcomm.com>
Cc: stable@vger.kernel.org # 6.4
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260518-qcom-ice-fix-v7-1-2a595382185b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Please consider pulling these changes from the signed vfs-7.1-rc5.fixes tag.
Thanks!
Christian
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCagq67gAKCRCRxhvAZXjc
ooRHAP0Scrpsiloo7JPM1u0DZZwvTdb9JRlx6k/KXkeN0j5L/wD9FVA9AXarcta5
h37k+SZpz8FuWkoY5LxTvUNbV6mr0w0=
=Enhi
-----END PGP SIGNATURE-----
Merge tag 'vfs-7.1-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"This contains a fixes for the current development cycle. Note that AI
related review sometimes delays fixes a bit because we find more fixes
for the fixes. I might try and send smaller but more fixes PRs if this
trend keeps up.
- Fix various netfslib bugs
- Fix an out-of-bounds write when listing idmappings
- Fix the return values in jfs_mkdir() and orangefs_mkdir()
- Fix a writeback writeback array overflow in fuse
- Fix a forced iversion increment on lazytime timestamp updates
- Reject a negative timeval component in kern_select()
- Fix error return when vfs_mkdir() fails in the cachefiles code
- Fix wrong error code returned for pidns ioctls"
* tag 'vfs-7.1-rc5.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (31 commits)
cachefiles: Fix error return when vfs_mkdir() fails
afs: Fix the locking used by afs_get_link()
netfs, afs: Fix write skipping in dir/link writepages
netfs: Fix netfs_read_folio() to wait on writeback
netfs: Fix folio->private handling in netfs_perform_write()
netfs: Fix partial invalidation of streaming-write folio
netfs: Fix potential UAF in netfs_unlock_abandoned_read_pages()
netfs: Fix leak of request in netfs_write_begin() error handling
netfs: Fix early put of sink folio in netfs_read_gaps()
netfs: Fix write streaming disablement if fd open O_RDWR
netfs: Fix read-gaps to remove netfs_folio from filled folio
netfs: Fix potential deadlock in write-through mode
netfs: Fix streaming write being overwritten
netfs: Defer the emission of trace_netfs_folio()
netfs: Fix netfs_invalidate_folio() to clear dirty bit if all changes gone
netfs: Fix overrun check in netfs_extract_user_iter()
netfs: fix error handling in netfs_extract_user_iter()
netfs: Fix potential uninitialised var in netfs_extract_user_iter()
netfs: fix VM_BUG_ON_FOLIO() issue in netfs_write_begin() call
netfs: Fix zeropoint update where i_size > remote_i_size
...
The struct 'mtk_hdmi_ddc_driver' is not used outside of the
mtk_hdmi_ddc.c file, so make it static to silence sparse warning:
```
drivers/gpu/drm/mediatek/mtk_hdmi_ddc.c:331:24: sparse: warning: symbol
'mtk_hdmi_ddc_driver' was not declared. Should it be static?
```
Fixes: c241118b62 ("drm/mediatek: mtk_hdmi_ddc: Switch to register as module_platform_driver")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260429-mediatek-drm-fix-sparse-warnings-v1-4-d95c4d118b83@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The struct 'mtk_cec_driver' is not used outside of the
mtk_cec.c file, so make it static to silence sparse warning:
```
drivers/gpu/drm/mediatek/mtk_cec.c:243:24: sparse: warning: symbol
'mtk_cec_driver' was not declared. Should it be static?
```
Fixes: 1e914a89ab ("drm/mediatek: mtk_cec: Switch to register as module_platform_driver")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260429-mediatek-drm-fix-sparse-warnings-v1-3-d95c4d118b83@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add linux device tree entry for Meta (Facebook) SanMiguel compute-tray
BMC using AT2620 SoC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Potin Lai <potin.lai.pt@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Add GMAC nodes for our MA35D1 development boards:
two RGMII interfaces for SOM board, and one RGMII
and one RMII interface for IoT board.
Signed-off-by: Joey Lu <a0987203069@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
When connecting to an AP configured for EHT 20 MHz with a full EHT
MCS/NSS map (supporting MCS 0-13)
Supported EHT-MCS and NSS Set
EHT-MCS Map (BW <= 80MHz): 0x444444
.... .... .... .... .... 0100 = Rx Max Nss That Supports EHT-MCS 0-9: 4
.... .... .... .... 0100 .... = Tx Max Nss That Supports EHT-MCS 0-9: 4
.... .... .... 0100 .... .... = Rx Max Nss That Supports EHT-MCS 10-11: 4
.... .... 0100 .... .... .... = Tx Max Nss That Supports EHT-MCS 10-11: 4
.... 0100 .... .... .... .... = Rx Max Nss That Supports EHT-MCS 12-13: 4
0100 .... .... .... .... .... = Tx Max Nss That Supports EHT-MCS 12-13: 4
TX throughput is observed to be significantly lower than expected.
Investigation shows that TX rates are limited to EHT MCS 11, even though
the AP advertises support for EHT MCS 12/13.
The root cause is an incorrect parsing of the Supported EHT-MCS and NSS
Set element in ath12k_peer_assoc_h_eht().
IEEE Std 802.11be-2024 Figure 9-1074as describes the format for 20
MHz-Only Non-AP STAs.
IEEE Std 802.11be-2024 Figure 9-1074at describes the format for all
other AP and non-AP STAs.
Currently the first format is parsed when the peer advertises no wider
HE channel width support, without considering whether it is an AP or a
non-AP STA. This is incorrect: the peer AP's capabilities must be parsed
using Figure 9-1074at even when it operates on 20 MHz only. Parsing it
as Figure 9-1074as causes rx_tx_mcs13_max_nss to be interpreted as zero,
which is then passed to firmware, leading firmware to assume the peer
does not support MCS 13 and to limit TX rates at MCS 11.
Fix this by parsing the Figure 9-1074as format only when the peer is a
20 MHz-Only non-AP STA, i.e. when the local interface operates as AP or
mesh point.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00302-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.115823.3
Fixes: 6c95151e2e ("wifi: ath12k: Add EHT MCS/NSS rates to Peer Assoc")
Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260514-ath12k-fix-20mhz-only-mcs-map-v1-1-a38d4a9b21a2@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
LMAC rings reuse the shared rdp/wrp pointer buffers without going
through the normal SRNG hw-init path that zeros non-LMAC ring
pointers. After restart, ath11k_hal_srng_clear() can therefore hand
stale hp/tp state from the previous firmware instance back to the new
one.
Clear the shared pointer buffers while keeping the allocations in
place so restart still avoids reallocating SRNG DMA memory, but starts
with fresh ring-pointer state.
Fixes: 32be3ca4cf ("wifi: ath11k: HAL SRNG: don't deinitialize and re-initialize again")
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/all/CAOPSVF04q6uvVdq8GTRLHBrVMdpt9=o9wVcFMc6f-yhmSBcZqQ@mail.gmail.com/
Signed-off-by: Kyle Farnung <kfarnung@gmail.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260513-kfarnung-ath11k-srng-clear-pointer-state-v1-1-bc700dd8b333@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In ath11k_dp_rx_msdu_coalesce() the loop uses ->is_continuation after
the dev_kfree_skb_any(). This can cause a use after free kfence.
Use flag for caching is_continuation for use after the
dev_kfree_skb_any().
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Willmar Knikker <willmar@met-dubbel-l.nl>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Reviewed-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Link: https://patch.msgid.link/20260505171709.547274-1-willmar@met-dubbel-l.nl
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
It has been observed that on certain chipsets a peer can be assigned
peer_id=0. For reception of non-aggregated MPDUs this is fine as
ath11k_dp_rx_h_find_peer() has a fallback case where it locates the peer
based upon the source MAC address. On an aggregated link, the mpdu_start
header is only populated by hardware on the first sub-MSDU. This causes
the peer resolution to be skipped for the subsequent MSDUs and the
encryption type of these frames to be set to an incorrect value,
resulting in these MSDUs being dropped by ieee80211.
ath11k_pci 0000:03:00.0: data rx skb 000000002f4b704d len 1534 peer xx:xx:xx:xx:xx:xx 0 ucast sn 3063 he160 rate_idx 9 vht_nss 2 freq 5240 band 1 flag 0x40d1a fcs-err 0 mic-err 0 amsdu-more 0 peer_id 0 first_msdu 1 last_msdu 0
ath11k_pci 0000:03:00.0: data rx skb 0000000038acd580 len 1534 peer (null) 0 ucast sn 3063 he160 rate_idx 9 vht_nss 2 freq 5240 band 1 flag 0x40d00 fcs-err 0 mic-err 0 amsdu-more 0 peer_id 0 first_msdu 0 last_msdu 1
Remove the null peer_id checks in ath11k_dp_rx_h_find_peer() and
ath11k_hal_rx_parse_mon_status_tlv(), allowing peers with an assigned ID
of 0 to be resolved.
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.9
Fixes: 2167fa606c ("ath11k: Add support for RX decapsulation offload")
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Matthew Leach <matthew.leach@collabora.com>
Reviewed-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260424-ath11k-null-peerid-workaround-v4-1-252b224d3cf6@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The mt8167 DSI controller is fully compatible with the one found in
mt2701. Unfortunately the device tree has a dedicated compatible for
mt8167 since 2022 and it cannot be changed with a fallback nor removed at
this point. The only way to get the device to work is to add the
compatible to the driver.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260505214541.333657-3-l.scorcia@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
ctxfi stores the Line Capture Switch and Mic Capture Switch controls in
a file-scope kctls[] array so do_line_mic_switch() can notify the
opposite control when the shared line/mic input selection changes.
That storage is shared by all ctxfi cards. If more than one X-Fi card is
present, a later card can overwrite the pointers saved by an earlier one.
A control update on one card can then use another card's kcontrol object
for snd_ctl_notify(). If that other card is removed, the saved pointer can
also become stale.
Store those notification targets in struct ct_mixer instead. The mixer is
per-card state and matches the lifetime of the controls created for that
card.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260517-alsa-ctxfi-mixer-kctls-v1-1-6e4f81f6b658@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace DRM_INFO(), DRM_WARN() and DRM_ERROR() calls in
drivers/gpu/drm/mediatek/mtk_dsi.c with the corresponding
drm_info(), drm_warn() and drm_err() helpers.
The drm_*() logging helpers take a struct drm_device * argument,
allowing the DRM core to prefix log messages with the correct device
name and instance. This is required to correctly distinguish log
messages on systems with multiple GPUs.
This change aligns the radeon driver with the DRM TODO item:
"Convert logging to drm_* functions with drm_device parameter".
Signed-off-by: Abhishek Rajput <abhiraj21put@gmail.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260420052008.5417-1-abhiraj21put@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The register COMMON_SLICE_CHICKEN4 is a MCR register on both Xe2 and
Xe3. Let's make sure to define a MCR version of it and use it for the
relevant IP versions.
Use XEHP_ as prefix for the register name, since it is MCR as of Xe_HP.
v2:
- Also change for one entry in lrc_tunnings, which was caught by
manual testing and add corresponging Fixes tag in commit message.
(Gustavo)
Fixes: 8d6f16f1f0 ("drm/xe: Extend Wa_22021007897 to Xe3 platforms")
Fixes: e5c13e2c50 ("drm/xe/xe2hpg: Add Wa_22021007897")
Fixes: 8ccf5f6b22 ("drm/xe/tuning: Apply windower hardware filtering setting on Xe3 and Xe3p")
Bspec: 66534, 71185, 74417
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-3-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit 75f65f1a4c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The register COMMON_SLICE_CHICKEN1 is a MCR register on Xe2.
Let's make sure to define a MCR version of it and use it for the
relevant IP versions.
Use XEHP_ as prefix for the register name, since it is MCR as of Xe_HP.
Fixes: a5d221924e ("drm/xe/xe2_hpg: Add set of workarounds")
Fixes: 9f18b55b6d ("drm/xe/xe2: Add workaround 18033852989")
Bspec: 66534, 71185
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-2-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit a672725fdb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
CACHE_MODE_1 is a MCR register for all platforms that currently use it
in the Xe driver. Use XE_REG_MCR() when defining it.
Fixes: 8cd7e97597 ("drm/xe: Add missing DG2 lrc workarounds")
Fixes: ff063430ca ("drm/xe/mtl: Add some initial MTL workarounds")
Bspec: 66534, 67788
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-1-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit 8f765f0c05)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reading debugfs file (/sys/kernel/debug/dri/0/gt*/pf/adverse_events)
with CFI (Control Flow Integrity) enabled, the kernel panics at
xe_gt_debugfs_simple_show+0x82/0xc0.
xe_gt_debugfs_simple_show() declare a function pointer expecting int
return type, but xe_gt_sriov_pf_monitor_print_events() is void return
type, leading to CFI failure and kernel panic.
[507620.973657] CFI failure at xe_gt_debugfs_simple_show+0x82/0xc0 [xe]
(target: xe_gt_sriov_pf_monitor_print_events+0x0/0x130 [xe]; expected
type: 0xd72c7139)
Fix xe_gt_sriov_pf_monitor_print_events() function by updating to return
an int type.
Fixes: 1c99d3d3ed ("drm/xe/pf: Expose PF monitor details via debugfs")
Signed-off-by: Mohanram Meenakshisundaram <mohanram.meenakshisundaram@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260514174918.1556357-2-mohanram.meenakshisundaram@intel.com
(cherry picked from commit ff1d386a83)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We have plugged-in existing VF print functions into our GT debugfs
show helper as-is, but we missed that the helper expects functions
to return int, while they were defined as void. This can lead to
errors being reported when CFI is enabled.
Fixes: 63d8cb8fe3 ("drm/xe/vf: Expose SR-IOV VF attributes to GT debugfs")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Mohanram Meenakshisundaram <mohanram.meenakshisundaram@intel.com>
Reviewed-by: Shuicheng Lin <shuicheng.lin@intel.com>
Link: https://patch.msgid.link/20260514155726.7165-1-michal.wajdeczko@intel.com
(cherry picked from commit 314e31c9a8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The error path in xe_gsc_init_post_hwconfig() explicitly frees a BO
allocated with xe_managed_bo_create_pin_map() via
xe_bo_unpin_map_no_vm(). Since the managed BO already has a devm
cleanup action registered, this causes a double-free when devm
unwinds during probe failure.
Remove the explicit free and let devm handle it, consistent with
all other xe_managed_bo_create_pin_map() callers.
Fixes: 2e5d47fe78 ("drm/xe/uc: Use managed bo for HuC and GSC objects")
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Assisted-by: Claude:claude-opus-4.6
Link: https://patch.msgid.link/20260511154134.223696-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 71d61e3e29)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
To workaround some corner case hardware limitations, new programming
note for the memory based interrupt handler suggests to assume that
some status bytes, like GT_MI_USER_INTERRUPT and GUC_INTR_GUC2HOST,
are always set. Update our interrupt handler to follow the new rules.
Bspec: 53672
Fixes: a6581ebe76 ("drm/xe/vf: Introduce Memory Based Interrupts Handler")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patch.msgid.link/20260511172838.2299-2-michal.wajdeczko@intel.com
(cherry picked from commit 284f4cae45)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Introduce a device tree node for the AST2600 PWM/Tach controller.
Describe register range, clock, reset, and cell configuration.
Set status to "disabled" by default.
Prepares for enabling PWM and tachometer support on platforms
utilizing this SoC.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Core usually prints endpoint addresses with 0x%X format.
Change this code to use it too, instead of just %d.
Particularly for IN, 0x83 seems more readable than 131.
While at that, fix checkpatch warnings about multi-line
quoted strings, as well as missing or doubled whitespace
in those strings.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073258.6532bdd5.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tao Xue found that some common devices violate USB 3.x section 9.6.7
by reporting wBytesPerInterval lower than the size of packets they
actually send. I confirmed that AX88179 may set it to 0 and RTL8153
CDC configuration sets it to 8 but sends both 8 and 16 byte packets:
S Ii:11:007:3 -115:128 16 <
C Ii:11:007:3 0:128 8 = a1000000 01000000
S Ii:11:007:3 -115:128 16 <
C Ii:11:007:3 0:128 16 = a12a0000 01000800 00000000 00000000
Most xHCI host controllers neglect interrupt bandwidth reservations
and let such devices exceed theirs, some fail the URB with EOVERFLOW.
Assume that wBytesPerInterval lower than wMaxPacketSize is bogus and
increase it to the worst case maximum on interrupt IN endpoints. This
solves xHCI problems and appears to have no other effect. Interrupt
transfers are not limited to one interval and drivers submit URBs of
class defined size without looking at wBytesPerInterval. Any multi-
interval transfer is considered terminated by a packet shorter than
wMaxPacketSize regardless of wBytesPerInterval - see USB3 8.10.3.
Stay in spec on OUT endpoints and isochronous. No buggy devices are
known and we don't want to risk sending more data than the device
is prepared to handle or confusing isoc drivers regarding altsetting
capacities guaranteed by the device itself. And don't complain when
wMaxPacketSize <= wBytesPerInterval < wMaxPacketSize * (bMaxBurst+1)
because enabling this seems to be the exact goal of the spec.
Reported-and-tested-by: Tao Xue <xuetao09@huawei.com>
Closes: https://lore.kernel.org/linux-usb/20260402021400.28853-1-xuetao09@huawei.com/
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073207.5b7d26e7.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no good reason to have wBytesPerInterval < wMaxPacketSize -
either one is too low or the other too high, and we may want to warn
about such descriptors. Start with cleaning up our own root hubs.
USB 3.2 section 10.15.1 sets wMaxPacketSize and wBytesPerInterval of
SuperSpeed hub status endpoints at 2 bytes, so reduce wMaxPacketSize
from its former value of 4, which was derived from USB 2.0 spec and
the kernel's USB_MAXCHILDREN limit. They don't apply because USB 3.2
10.15.2.1 specifies SuperSpeed hubs to have up to 15 ports.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073121.7bc1da0f.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, a few races have been discovered in the GEM LRU logic, all
of them caused by the fact the LRU lock is accessed through
gem->lru->lock, and that very same lock also protects changes to
gem->lru, leading to situations where gem->lru needs to first be
accessed without the lock held, to then get the lru to access the lock
through and finally take the lock and do the expected operation.
Currently, the only driver making use of this API (MSM) declares a
device-wide lock, and the user we're about to add (panthor) will
do the same. There's no evidence that we will ever have a driver
that wants different pools of LRUs protected by different locks under
the same drm_device. So we're better off moving this lock to drm_device
and always locking it through obj->dev->gem_lru_mutex, or directly
through dev->gem_lru_mutex.
If anyone ever needs more fine-grained locking, this can be revisited
to pass some drm_gem_lru_pool object representing the pool of LRUs
under a specific lock, but for now, the per-device lock seems to be
enough.
Fixes: e7c2af13f8 ("drm/gem: Add LRU/shrinker helper")
Reported-by: Chia-I Wu <olvaffe@gmail.com>
Closes: https://gitlab.freedesktop.org/panfrost/linux/-/work_items/86
Reviewed-by: Rob Clark <rob.clark@oss.qualcomm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: https://patch.msgid.link/20260518-panthor-shrinker-fixes-v4-1-1920234470d5@collabora.com
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
do_flash() locates the first .cyacd record with
p = strnchr(fw->data, fw->size, ':');
while (p < eof) {
s = strnchr(p + 1, eof - p - 1, ':');
...
}
If the firmware image contains no ':' byte, strnchr() returns NULL.
NULL compares less than the valid kernel pointer eof, so the loop body
runs and strnchr() is called with p + 1 == (void *)1 and a length of
roughly (unsigned long)eof, causing a wonderful crash.
The not_signed_fw fallthrough earlier in do_flash() and the chip-state
branches in ccg_fw_update_needed() allow an unsigned blob to reach this
loop, so a root user who can place a crafted file under /lib/firmware
and write the do_flash sysfs attribute can trigger the oops.
Bail out with -EINVAL when the initial strnchr() returns NULL.
Assisted-by: gkh_clanker_t1000
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026051405-posture-shrill-7884@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WebUSB GET_URL handler in composite_setup() narrows
landing_page_length to fit the host-supplied wLength using
landing_page_length = w_length
- WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH + landing_page_offset;
If wLength is smaller than WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH the
unsigned subtraction wraps, and the subsequent
memcpy(url_descriptor->URL,
cdev->landing_page + landing_page_offset,
landing_page_length - landing_page_offset);
ends up copying close to UINT_MAX bytes from cdev->landing_page into
cdev->req->buf. KASAN reports a slab-out-of-bounds in composite_setup
on the kmalloc-2k gadget_info allocation, and FORTIFY_SOURCE traps the
memcpy as a 4294967293-byte field-spanning write into
url_descriptor->URL (size 252).
A USB host can reach this from a single SETUP packet against any
gadget that has webusb/use=1 and a landingPage configured.
Handle the small-wLength case before the math: when the host requested
fewer bytes than the URL descriptor header, only the header is
meaningful and no URL bytes need to be copied. Setting
landing_page_length to landing_page_offset makes the existing memcpy a
no-op and leaves the descriptor returned to the host unchanged for all
larger wLength values.
Fixes: 93c473948c ("usb: gadget: add WebUSB landing page support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jeremy Erazo <mendozayt13@gmail.com>
Link: https://patch.msgid.link/20260512160530.352318-1-mendozayt13@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the error code on these two error paths. The existing code returns
success.
Fixes: 77ed2f4538 ("usb: typec: tipd: Use read_power_status function in probe")
Fixes: 04041fd7d6 ("usb: typec: tipd: Read data status in probe and cache its value")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/agL9o7wUK1dOVBTy@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ovl_iterate_merged() stores PTR_ERR(cache) in err before checking
IS_ERR(cache). On success err holds the truncated cache pointer and
can be returned as a bogus non-zero error.
The syzbot reproducer reaches this through overlay-on-overlay readdir:
getdents64
iterate_dir(outer overlay file)
ovl_iterate_merged()
ovl_cache_get()
ovl_dir_read_merged()
ovl_dir_read()
iterate_dir(inner overlay file)
ovl_iterate_merged()
Only compute PTR_ERR(cache) on the error path.
Fixes: d25e4b739f ("ovl: refactor ovl_iterate() and port to cred guard")
Reported-by: syzbot+a16fb0cce329a320661c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a16fb0cce329a320661c
Cc: stable@vger.kernel.org
Signed-off-by: Nirmoy Das <nirmoyd@nvidia.com>
Link: https://patch.msgid.link/20260514144258.3068715-1-nirmoyd@nvidia.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add an MP5998 power monitor used to monitor the power consumption
of the Paddle_P12V_HSC rail on the Yosemite5 paddle board.
[arj: Remove changelog from commit message]
Signed-off-by: Daniel Hsu <Daniel-Hsu@quantatw.com>
Link: https://patch.msgid.link/20260331120734.39260-1-Daniel-Hsu@quantatw.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
dm_poll_bio() is the ->poll_bio() callback for a stacked dm device.
The caller only knows about the dm queue, so it may decide to do a
spinning poll if it thinks a single queue is being polled. Passing those
flags unchanged to the mapped clone lets blk_mq_poll() spin on a target
queue from inside dm_poll_bio().
With io_uring IOPOLL on a dm-stripe target this can keep a task in
dm_poll_bio() -> bio_poll() -> blk_mq_poll()
long enough to trigger an RCU CPU stall, before io_uring gets back to
io_iopoll_check() and its need_resched() check.
Keep dm's ->poll_bio() bounded by forcing one-shot polling for target
bios. The caller can invoke dm_poll_bio() again if it wants to keep
polling, and it also gets a chance to reap completions or reschedule
between passes.
Fixes: f22ecf9c14 ("blk-mq: delete task running check in blk_hctx_poll()")
Signed-off-by: Fengnan Chang <changfengnan@bytedance.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
When we send a message to a device that has no table, the return code was
not set. The code would return "2", which is not considered a valid return value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com>
This adds the admin-guide documentation for dm-inlinecrypt.
dm-inlinecrypt.rst is the guide to using dm-inlinecrypt.
Signed-off-by: Linlin Zhang <linlin.zhang@oss.qualcomm.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
As described in commit 2bc0576925 ("block: don't make REQ_POLLED imply
REQ_NOWAIT"), which fixed the same issue for the block device node, there
are valid cases to poll for I/O completion without REQ_NOWAIT.
Additionally, sing REQ_NOWAIT for file system writes is currently not
supported as file systems writes are not idempotent and would need a
retry of just the bio and not the entire operation to be fully supported.
Switch iomap to set REQ_POLLED and remove the now unused bio_set_polled
helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260518062917.506483-1-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
The current SysFS flow first enables the links and sink, then rolls back
to disable them if the source fails to enable. This failure can occur if
the associated CPU is offline, which causes the SMP call to fail.
Validate whether the associated CPU is online for a per-CPU tracer.
If the CPU is offline, return -ENODEV and bail out.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-28-f88c4a3ecfe9@arm.com
This commit moves CPU hotplug callbacks from ETMv4 driver to core layer.
The motivation is the core layer can control all components on an
activated path rather but not only managing tracer in ETMv4 driver.
The perf event layer will disable CoreSight PMU event 'cs_etm' when
hotplug off a CPU. That means a perf mode will be always converted to
disabled mode in CPU hotplug. Arm CoreSight CPU hotplug callbacks only
need to handle the Sysfs mode and ignore the perf mode.
Add a 'mode' argument to coresight_pm_get_active_path() so it only
returns active paths for the relevant mode. Define the enum with bit
flags so it is safe for bitwise operations.
Change CPUHP_AP_ARM_CORESIGHT_STARTING to CPUHP_AP_ARM_CORESIGHT_ONLINE
so that the CPU hotplug callback runs in the online state and thread
context, allowing coresight_disable_sysfs() to be called directly to
disable the path.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-27-f88c4a3ecfe9@arm.com
Except for software sources (e.g. STM), other sources treat multiple
enables as equivalent to a single enable. The device mode already
tracks the binary state, so it is redundant to operate refcount.
Introduce a helper coresight_is_software_source() for check software
source. Refactor to maintain the refcount only for software sources.
This simplifies future CPU PM handling without refcount logic.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-26-f88c4a3ecfe9@arm.com
Add interrupt-parent and interrupts properties to the PDB PCA9555
nodes in the anacapa DTS.
[arj: Tweak commit subject capitalisation]
Signed-off-by: Rex Fu <Rex.Fu@amd.com>
Link: https://patch.msgid.link/20260417-anacapa-pca9555-irq-v1-1-9a6d28b1b656@amd.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Instead of projecting using pointer to a field project the full slot. This
further shifts the code generation from the initializer site to the struct
definition site, which means less code is generated overall.
It also makes the safety comment easier to justify, as now the projection
is done by the `#[pin_data]` macro which has full visibility of pinnedness
of fields.
The field alignment could also be checked on the `#[pin_data]` side;
however, since `init!()` macro works for other type of structs, we cannot
remove the alignment check from `init!`/`pin_init!` side anyway, so I opted
to still keep the alignment check in init.rs.
Signed-off-by: Gary Guo <gary@garyguo.net>
By projecting slots, the `pin_init!` and `init!` code path can be more
unified. This also reduces the amount of macro-generated code and shifts
them to the shared infrastructure.
Signed-off-by: Gary Guo <gary@garyguo.net>
The `InitData` and `PinData` traits do not need to exist, the inference
helpers could be inherent methods instead.
There is no risk for calling the wrong methods even when user defines it,
as inherent methods take priority over trait methods.
With this change, it unlocks the possibility of attaching additional bounds
to the method per type, which is not possible for trait methods.
Signed-off-by: Gary Guo <gary@garyguo.net>
Instead of projecting the created reference, simply create drop guards with
different marker types and have the `let_binding()` method of guards of
different marker produce different type instead.
This allows more flexible lifetime as this is now controlled by the guard.
This will be needed when implementing self-referential fields.
Signed-off-by: Gary Guo <gary@garyguo.net>
`InitializerKind::Code` is a special case where it does not initialize a
field, and thus generate no guard and accessors. Handle it earlier and make
the rest of the code more linear.
Signed-off-by: Gary Guo <gary@garyguo.net>
The ACS specification does not allow a non-NCQ command to be issued while
an NCQ command is outstanding.
Commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
introduced a feature where a deferred non-NCQ command gets issued from a
workqueue. The design stores a single non-NCQ command per port.
However, when using Port Multipliers (PMPs), specifically PMPs that
support FIS-Based Switching (FBS), non-NCQ and NCQ commands can be mixed
on the same port, just not for the same link, see e.g. ata_std_qc_defer()
which is, and always has operated on a per-link basis.
Therefore, move the deferred_qc from struct ata_port to struct ata_link.
This way, when using a PMP with FBS, we will not needlessly defer commands
to all other links, just because one link issued a non-NCQ command while
having an NCQ command outstanding. Only commands for that specific link
will be deferred. This is in line with how PMPs with FBS worked before
commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation").
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Tested-by: Tommy Kelly <linux@tkel.ly>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
When using Port Multipliers (PMPs) with Command-Based Switching (CBS), you
can only issue commands to one link at a time. For PMPs with CBS, there is
already code to handle commands being sent to different links in
sata_pmp_qc_defer_cmd_switch() using ap->excl_link. sata_sil24 also makes
use of ap->excl_link.
A user on the list reported that commit 0ea84089db ("ata: libata-scsi:
avoid Non-NCQ command starvation") broke PMPs with CBS. The commit
introduced code that stores a deferred qc in ap->deferred_qc, to later be
issued via a workqueue. It turns out that this change is incompatible with
the existing ap->excl_link handling used by PMPs with CBS.
Thus, modify sata_pmp_qc_defer_cmd_switch() and sil24_qc_defer() to return
ATA_DEFER_LINK_EXCL, and make sure that the deferred QC handling via
workqueue is not used for this return value.
This way, PMPs with CBS will work once again. Note that the starvation
referenced in commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ
command starvation") can only happen on libsas ports, and libsas does not
support Port Multipliers, thus there is no harm of reverting back to the
previous way of deferring commands for PMPs with CBS.
Non-libsas ports connected to anything but a PMP with CBS (e.g. a normal
drive or a PMP with FBS) will continue using the deferred workqueue, since
it does result in lower completion latencies for non-NCQ commands, even
though the workqueue is not strictly needed to avoid starvation for
non-libsas ports.
If we want to modify the scope of the workqueue issuing to also handle
PMPs with CBS, then we should ensure that we can save both NCQ and non-NCQ
commands in ap->deferred_qc, while also removing the existing PMP CBS
handling using ap->excl_link, such that we don't duplicate features.
While at it, also add a comment explaining how the ap->excl_link mechanism
works.
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Tested-by: Tommy Kelly <linux@tkel.ly>
Reported-by: Tommy Kelly <linux@tkel.ly>
Closes: https://lore.kernel.org/linux-ide/ce09cc21-a8e9-4845-b205-35411e22fba9@tkel.ly/
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
