Currently brcmfmac is expecting to be set for both
BRCMF_VIF_STATUS_EAP_SUCCESS and BRCMF_VIF_STATUS_EAP status bit based
on dongle event and those bits are cleared to complete connect request
successfully.
But when connect request is finished unsuccessfully, either
BRCMF_VIF_STATUS_EAP_SUCCESS / BRCMF_VIF_STATUS_EAP bits are not
cleared depending on how the connect fail event happens. These status
bits are carried over to following new connect request and this will lead
to generate below kernel warning for some case. Worst case status
mismatch happens between dongle and wpa_supplicant.
WARNING: ../net/wireless/sme.c:756 __cfg80211_connect_result+0x42c/0x4a0 [cfg80211]
The fix is to clear the BRCMF_VIF_STATUS_EAP_SUCCESS /
BRCMF_VIF_STATUS_EAP bits during the link down process and add to call
link down process when link down event received during
BRCMF_VIF_STATUS_CONNECTING as well as BRCMF_VIF_STATUS_CONNECTED
state.
Signed-off-by: Wataru Gohda <wataru.gohda@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221024085215.27616-3-ian.lin@infineon.com
When deleting a P2P AGO interface we should make sure that
relevant entry in bss_idx[] array is removed. We were always
removing only 'vif' at P2PAPI_BSSCFG_CONNECTION before,
regardless of the number of created P2P AGO interfaces.
brcmfmac: correctly remove all p2p vif
Signed-off-by: Brian Henriquez <brian.henriquez@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Signed-off-by: Ian Lin <ian.lin@infineon.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221024085215.27616-2-ian.lin@infineon.com
Fix the following W=1 kernel warnings:
drivers/gpu/drm/i915/gvt/aperture_gm.c:308: warning: expecting prototype
for inte_gvt_free_vgpu_resource(). Prototype was for
intel_vgpu_free_resource() instead.
drivers/gpu/drm/i915/gvt/aperture_gm.c:344: warning: expecting prototype
for intel_alloc_vgpu_resource(). Prototype was for
intel_vgpu_alloc_resource() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220602073519.22363-1-jiapeng.chong@linux.alibaba.com
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fix the following W=1 kernel warnings:
drivers/gpu/drm/i915/gvt/mmio_context.c:560: warning: expecting
prototype for intel_gvt_switch_render_mmio(). Prototype was for
intel_gvt_switch_mmio() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220524083733.67148-1-jiapeng.chong@linux.alibaba.com
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Fix the following W=1 kernel warnings:
drivers/gpu/drm/i915/gvt/handlers.c:3066: warning: expecting prototype
for intel_t_default_mmio_write(). Prototype was for
intel_vgpu_default_mmio_write() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220524083733.67148-2-jiapeng.chong@linux.alibaba.com
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The recent fix for the delayed card registration made the current
workaround for QUIRK_AUTODETECT superfluous, since the card
registration itself is delayed until the last interface probe.
This patch drops the redundant workaround in
create_autodetect_quirks() for simplification.
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Link: https://bugzilla.suse.com/show_bug.cgi?id=1205111
Link: https://lore.kernel.org/r/20221108065824.14418-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although we tried to fix the regression for the recent changes with
the delayed card registration, it doesn't seem covering the all
cases; e.g. on Roland EDIROL M-100FX, where the generic quirk for
Roland devices is applied, it misses the card registration because the
detection of the last interface (apparently for MIDI) fails.
This patch is an attempt to recover from those failures by calling the
card register also at the error path for the secondary interfaces.
The card register condition is also extended to match with the old
check in the previous patch, too (i.e. the simple check of the
interface number) for catching the probe with errors.
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1205111
Link: https://lore.kernel.org/r/20221108065824.14418-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 40064aeca3 ("percpu: replace area map allocator with
bitmap"), there's no place to use PERCPU_DYNAMIC_EARLY_SLOTS. So
clean it up.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Since commit b239f7daf5 ("percpu: set PCPU_BITMAP_BLOCK_SIZE to
PAGE_SIZE"), the PCPU_BITMAP_BLOCK_SIZE has been set to page size
fixedly. So the lcm code in pcpu_alloc_first_chunk() doesn't make
sense any more, clean it up.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
In function pcpu_reclaim_populated(), the line of goto jumping is
unnecessary since the label 'end_chunk' is near the end of the for
loop, use break instead.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
When allocating an area from a chunk, pcpu_block_update_hint_alloc()
is called to update chunk metadata, including chunk's and global
nr_empty_pop_pages. However, if the allocation is not atomic, some
blocks may not be populated with pages yet, while we still subtract
the number here. The number of pages will be added back with
pcpu_chunk_populated() when populating pages.
Adding code comment to make that more understandable.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
The lock pcpu_alloc_mutex taking code has been moved to the beginning of
pcpu_allo() if it's non atomic allocation. So the code comment above
above pcpu_create_chunk() callsite need be updated.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
To replace list_empty()/list_first_entry() pair to simplify code.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Since commit 40064aeca3 ("percpu: replace area map allocator with
bitmap"), it is unneeded.
Signed-off-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
For unmapped range, the returned map.m_llen is zero, and thus the
calculated count is unexpected zero.
Prior to the refactoring introduced by commit 1ae9470c3e ("erofs:
clean up .read_folio() and .readahead() in fscache mode"), only the
readahead routine suffers from this. With the refactoring of making
.read_folio() and .readahead() calling one common routine, both
read_folio and readahead have this issue now.
Fix this by calculating count separately in unmapped condition.
Fixes: c665b394b9 ("erofs: implement fscache-based data readahead")
Fixes: 1ae9470c3e ("erofs: clean up .read_folio() and .readahead() in fscache mode")
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20221104054028.52208-3-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
SAT SCSI/ATA Translation specification requires SCSI SYNCHRONIZE CACHE
(10) and (16) commands both shall be translated to ATA flush command.
Also, ZBC Zoned Block Commands specification mandates SYNCHRONIZE CACHE
(16) command support. However, libata translates only SYNCHRONIZE CACHE
(10). This results in SYNCHRONIZE CACHE (16) command failures on SATA
drives and then libata translation does not conform to ZBC. To avoid the
failure, add support for SYNCHRONIZE CACHE (16).
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
atc_complete_all() had concurrency bugs, thus remove it:
1/ atc_complete_all() in its entirety was buggy, as when the atchan->queue
list (the one that contains descriptors that are not yet issued to the
hardware) contained descriptors, it fired just the first from the
atchan->queue, but moved all the desc from atchan->queue to
atchan->active_list and considered them all as fired. This could result in
calling the completion of a descriptor that was not yet issued to the
hardware.
2/ when in tasklet at atc_advance_work() time, atchan->active_list was
queried without holding the lock of the chan. This can result in
atchan->active_list concurrency problems between the tasklet and
issue_pending().
Fixes: dc78baa2b9 ("dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221025090306.297886-1-tudor.ambarus@microchip.com
Link: https://lore.kernel.org/r/20221025090306.297886-8-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
tx_submit is supposed to push the current transaction descriptor to a
pending queue, waiting for issue_pending() to be called. issue_pending()
must start the transfer, not tx_submit(), thus remove atc_dostart() from
atc_tx_submit(). Clients of at_xdmac that assume that tx_submit() starts
the transfer must be updated and call dma_async_issue_pending() if they
miss to call it.
The vdbg print was moved to after the lock is released. It is desirable to
do the prints without the lock held if possible, and because the if
statement disappears there's no reason why to do the print while holding
the lock.
Fixes: dc78baa2b9 ("dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20221025090306.297886-1-tudor.ambarus@microchip.com
Link: https://lore.kernel.org/r/20221025090306.297886-3-tudor.ambarus@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When disabling dma channel, a TCF flag is set and as TCIE is enabled, an
interrupt is raised.
On a busy system, the interrupt may have latency and the user can ask for
dmaengine_resume while stm32-dma driver has not yet managed the complete
pause (backup of registers to restore state in resume).
To avoid such a case, instead of waiting the interrupt to backup the
registers, do it just after disabling the channel and discard Transfer
Complete interrupt in case the channel is paused.
Fixes: 099a9a94be ("dmaengine: stm32-dma: add device_pause/device_resume support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20221024083611.132588-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If device_register() fails, it should call put_device() to give
up reference, the name allocated in dev_set_name() can be freed
in callback function kobject_cleanup().
Fixes: 5b65781d06 ("dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221020062827.2914148-1-yangyingliang@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The of_xlate callback is supposed to return the channel after already
having 'grabbed' it for private use, so fill that in.
Fixes: b127315d9a ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221019132324.8585-1-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When IDXD is not configurable, that means its WQ, engine, and group
configurations cannot be changed. But it can be disabled and its state
should be set as disabled regardless it's configurable or not.
Fix this by setting device state IDXD_DEV_DISABLED for read-only device
as well in idxd_device_clear_state().
Fixes: cf4ac3fef3 ("dmaengine: idxd: fix lockdep warning on device driver removal")
Signed-off-by: Fengqian Gao <fengqian.gao@intel.com>
Reviewed-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930032835.2290-1-fengqian.gao@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From Intel IAA spec [1], Intel IAA does not support batch processing.
Two batch related default values for IAA are incorrect in current code:
(1) The max batch size of device is set during device initialization,
that indicates batch is supported. It should be always 0 on IAA.
(2) The max batch size of work queue is set to WQ_DEFAULT_MAX_BATCH (32)
as the default value regardless of Intel DSA or IAA device during
work queue setup and cleanup. It should be always 0 on IAA.
Fix the issues by setting the max batch size of device and max batch
size of work queue to 0 on IAA device, that means batch is not
supported.
[1]: https://cdrdv2.intel.com/v1/dl/getContent/721858
Fixes: 23084545db ("dmaengine: idxd: set max_xfer and max_batch for RO device")
Fixes: 92452a72eb ("dmaengine: idxd: set defaults for wq configs")
Fixes: bfe1d56091 ("dmaengine: idxd: Init and probe for Intel data accelerators")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Link: https://lore.kernel.org/r/20220930201528.18621-2-xiaochen.shen@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The first IRQ is required, but IRQs 1 through (nb_phy_chans - 1) are
optional, because on some platforms (e.g. PXA168) there is a single IRQ
shared between all channels.
This change inhibits a flood of "IRQ index # not found" messages at
startup. Tested on a PXA168-based device.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20220906000709.52705-1-doug@schmorgal.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clean the Qualcomm SoCs clock bindings:
1. Drop redundant "bindings" in title.
2. Correct language grammar "<independent clause without verb>, which
supports" -> "provides".
3. Use full path to the bindings header, so tools can validate it.
4. Drop quotes where not needed.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> # msm8998
Acked-by: Jeffrey Hugo <quic_jhugo@quicinc.com> # mmcc
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221102163153.55460-2-krzysztof.kozlowski@linaro.org
Like MSM8916 and some others, MSM8976 uses qcom,smd-channels and not
qcom,glink-channels.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104172122.252761-5-angelogioacchino.delregno@collabora.com
Change order of SMMU clocks to match the schema.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221102184420.534094-2-dmitry.baryshkov@linaro.org
Accidentally discovered a hidden typo in the DT-nodes defined in the
opp-v2 bindings example. Instead of specifying the "clock-latency-ns"
property the DT-node has been created with the "lock-latency-ns" property
in it, which doesn't exist neither in opp-v2 nor in the base schemas.
Let's fix the name to having the "clock-" prefix as it was originally
implied and as the rest of the similar nodes has.
Fixes: 94274f20f6 ("dt-bindings: opp: Convert to DT schema")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add support for Sony Xperia 10 IV, a.k.a PDX225. This device is a part
of the SoMC SM6375 Murray platform and currently it is the only
device based on that board, so no -common DTSI is created until (if?)
other Murray devices appear.
This commit brings support for:
* USB (only USB2 for now)
* Display via simplefb
To create a working boot image, you need to run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm6375-sony-xperia-\
murray-pdx225.dtb > .Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd.img \
--pagesize 4096 \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--tags_offset 0x100 \
--cmdline "SOME_CMDLINE" \
--dtb_offset 0x1f00000 \
--header_version 1 \
--os_version 12 \
--os_patch_level 2022-04 \ # or newer
-o boot.img-sony-xperia-pdx225
Then, you need to flash it on the device and get rid of all the
vendor_boot/dtbo mess:
First, you need to get rid of vendor_boot. However, the bootloader
is utterly retarded and it will not let you neither flash nor erase it.
There are a couple ways to handle this: you can either dd /dev/zero to
it from Android (if you have root) or a custom recovery or from fastbootd
(fastboot/adb reboot fastboot). You will not be able to boot Android
images on your phone unless you lock the bootloader (fastboot oem lock)
and restore the factory image with Xperia Companion
Windows-and-macOS-only software.
The best way so far is probably to use the second (_b) slot and flash
mainline there. This will however require you to flash some partitions
manually, as they are not populated from factory:
(boot_b, dtbo_b, vendor_boot_b, vbmeta_b, vbmeta_system_b) - these we
don't really care about as we nuke/replace them
(dsp_b, imagefv_b, modem_b, oem_b, rdimage_b) - these you NEED to populate
to get a successful boot on slot B, otherwise you will have limited / no
functionality.
To switch slots, simply run:
fastboot --set-active=a //or =b
The rest assumes you are on slot A.
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP
fastboot --disable-verity --disable-verification flash vbmeta_b vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system_b \
vbmeta_system.img
fastboot flash boot_b boot.img-sony-xperia-pdx225
fastboot reboot fastboot // entering fastbootd
fastboot flash vendor_boot_b emptything.img
fastboot flash dtbo_b emptything.img
fastboot reboot bootloader // entering bootloader fastboot
fastboot --set-active=b
fastboot reboot // mainline time!
Where emptything.img is a tiny file that consists of 2 bytes (all zeroes),
doing a "fastboot erase" won't cut it, the bootloader will go crazy and
things will fall apart when it tries to overlay random bytes from an empty
partition onto a perfectly good appended DTB.
From there on you can flash new mainline builds by simply flashing
boot.img that you create after each kernel rebuild.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107120920.12593-4-konrad.dybcio@linaro.org
Add an initial device tree for the SM6375 (SD695) SoC.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107120920.12593-3-konrad.dybcio@linaro.org
