[ Upstream commit 44c03802a5 ]
The isp_video_mbus_to_pix/pix_to_mbus functions did not take
the last empty entry { 0, } of the formats array into account.
As a result, isp_video_mbus_to_pix would accept code 0 and
isp_video_pix_to_mbus would select code 0 if no match was found.
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ac3be217c ]
When SPI communication is suspended by hardware automatically, it could
happen that few bits of next frame are already clocked out due to
internal synchronization delay.
To achieve a safe suspension, we need to ensure that each word must be
at least 8 SPI clock cycles long. That's why, if bpw is less than 8
bits, we need to use midi to reach 8 SPI clock cycles at least.
This will ensure that each word achieve safe suspension and prevent
overrun condition.
Signed-off-by: Deepak Kumar <deepak.kumar01@st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://patch.msgid.link/20251218-stm32-spi-enhancements-v2-2-3b69901ca9fe@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4e620eccb ]
Currently the buffers are being filled until full, which works fine
for the transport stream, but not when reading sections, those have
to be returned to userspace immediately, otherwise dvbv5-scan will
just wait forever.
Add a 'flush' argument to dvb_vb2_fill_buffer to indicate whether
the buffer must be flushed or wait until it is full.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d96cb0b86d ]
There are message types when we would need to send a payload along with
the LARGE_CONFIG_GET message to provide information to the firmware on
what data is requested.
Such cases are the ALSA Kcontrol related messages when the high level
param_id tells only the type of the control, but the ID/index of the exact
control is specified in the payload area.
The caller must place the payload for TX before calling the set_get_data()
and this payload will be sent alongside with the message to the firmware.
The data area will be overwritten by the received data from firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20251217143945.2667-7-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aeb31b245 ]
[WHY]
User may connect mst dock with multi monitors and do quick unplug
and plug in one of the monitor. This operatioin may create CSN from
dock to display driver. Then display driver would disable and then enable
mst link and also disable/enable DPCD mst_en bit in dock RX. However,
when mst_en bit being disabled, if dock has another CSN message to
transmit then the message would be removed because of the disabling of
mst_en. In this case, the message is missing and it ends up no display in
the replugged monitor.
[HOW]
Don't disable mst_en bit when link still has sink connected.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea573a8e1 ]
[Why]
USB-C DisplayPort Alt Mode with concurrent USB data needs lane count
limitation to prevent incorrect 4-lane DP configuration when only 2 lanes
are available due to hardware lane sharing between DP and USB3.
[How]
Query DMUB for Alt Mode status (is_dp_alt_disable, is_usb, is_dp4) in
dcn32_link_encoder_get_max_link_cap() and cap DP to 2 lanes when USB is
active on USB-C port. Added inline documentation explaining the USB-C
lane sharing constraint.
Reviewed-by: PeiChen Huang <peichen.huang@amd.com>
Signed-off-by: LinCheng Ku <lincheng.ku@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f0736a4e1 ]
The recent refactoring of where runtime PM is enabled done in commit
f1eb4e792b ("spi: spi-cadence-quadspi: Enable pm runtime earlier to
avoid imbalance") made the fact that when we do a pm_runtime_disable()
in the error paths of probe() we can trigger a runtime disable which in
turn results in duplicate clock disables. This is particularly likely
to happen when there is missing or broken DT description for the flashes
attached to the controller.
Early on in the probe function we do a pm_runtime_get_noresume() since
the probe function leaves the device in a powered up state but in the
error path we can't assume that PM is enabled so we also manually
disable everything, including clocks. This means that when runtime PM is
active both it and the probe function release the same reference to the
main clock for the IP, triggering warnings from the clock subsystem:
[ 8.693719] clk:75:7 already disabled
[ 8.693791] WARNING: CPU: 1 PID: 185 at /usr/src/kernel/drivers/clk/clk.c:1188 clk_core_disable+0xa0/0xb
...
[ 8.694261] clk_core_disable+0xa0/0xb4 (P)
[ 8.694272] clk_disable+0x38/0x60
[ 8.694283] cqspi_probe+0x7c8/0xc5c [spi_cadence_quadspi]
[ 8.694309] platform_probe+0x5c/0xa4
Dealing with this issue properly is complicated by the fact that we
don't know if runtime PM is active so can't tell if it will disable the
clocks or not. We can, however, sidestep the issue for the flash
descriptions by moving their parsing to when we parse the controller
properties which also save us doing a bunch of setup which can never be
used so let's do that.
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Closes: https://lore.kernel.org/r/20251201072844.GA6785@francesco-nb
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20251204-spi-cadence-qspi-runtime-pm-imbalance-v2-1-10af9115d531@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb2bbe3838 ]
mas->cur_bits_per_word may not reflect the value of xfer->bits_per_word
when can_dma() is called. Use the right value instead.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-3-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 739062a9f1 ]
setup_fifo_params assumes these will be zero, it won't write these
registers if the initial mode is zero.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://patch.msgid.link/20251120211204.24078-4-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b57c3c3f2 ]
Only check and drain IH1 ring if CAM is not enabled.
If GPU is under reset, don't access IH to drain retry fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcd752c706 ]
A 14-inch 2560x1600 60Hz matte touch panel, found on a Dell Latitude 7455
laptop (second-source with BOE NE14QDM), according to online sources it's
also found on the Latitude 7440 and some ASUS models.
Raw EDID dump:
00 ff ff ff ff ff ff 00 06 af a4 0b 00 00 00 00
00 20 01 04 a5 1e 13 78 03 ad f5 a8 54 47 9c 24
0e 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 f0 68 00 a0 a0 40 2e 60 30 20
35 00 2d bc 10 00 00 1a f3 53 00 a0 a0 40 2e 60
30 20 35 00 2d bc 10 00 00 1a 00 00 00 fe 00 36
39 52 31 57 80 42 31 34 30 51 41 58 00 00 00 00
00 02 41 21 a8 00 01 00 00 1a 41 0a 20 20 00 a1
Don't have datasheet access, but the same timing as for other panels from
the same manufacturer works fine.
Signed-off-by: Val Packett <val@packett.cool>
[dianders: Moved to the right location in the table]
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20251206173739.2222940-1-val@packett.cool
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dedb906cd ]
[WHY&HOW]
If DMCUB is not initialized or FAMS2 is not supported, the
interface should not be called.
Reviewed-by: Sridevi Arvindekar <sridevi.arvindekar@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 531fe6e0fe ]
[WHY&HOW]
The condition is only perform toggle if FIXED_VS LTTPR reports
no IEEE OUI.
The literal "\x0,\x0,\x0" contains commas changes the
bytes being compared to {0x00,0x2C,0X00}.
The correct literal should be "\x00\x00\x00" without commas.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f752e79d38 ]
__amdgpu_ras_restore_bad_pages is responsible for the maintenance of bad
page number, drop the unnecessary bad page number update in the error
handling path of add_bad_pages.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9877a865d6 ]
If SDMA block not enabled, buffer_funcs will not initialize,
fix the null pointer issue if buffer_funcs not initialized.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd77d5a4aa ]
In mailbox_get_msg(), mailbox_reg_read_non_zero() is called to poll for a
non-zero tail pointer. This assumed that a zero value indicates an error.
However, certain corner cases legitimately produce a zero tail pointer.
To handle these cases, remove mailbox_reg_read_non_zero(). The zero tail
pointer will be treated as a valid rewind event.
Reviewed-by: Maciej Falkowski <maciej.falkowski@linux.intel.com>
Signed-off-by: Lizhi Hou <lizhi.hou@amd.com>
Link: https://patch.msgid.link/20251204181603.793824-1-lizhi.hou@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2976aeb0de ]
Add an eDP panel entry for AUO B140HAN06.4 that is also used in
some variants of Lenovo Flex 5G with Qcom SC8180 SoC.
The raw edid of the panel is:
00 ff ff ff ff ff ff 00 06 af 3d 64 00 00 00 00
2b 1d 01 04 a5 1f 11 78 03 b8 1a a6 54 4a 9b 26
0e 52 55 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 14 37 80 b8 70 38 24 40 10 10
3e 00 35 ae 10 00 00 18 10 2c 80 b8 70 38 24 40
10 10 3e 00 35 ae 10 00 00 18 00 00 00 fe 00 41
55 4f 0a 20 20 20 20 20 20 20 20 20 00 00 00 fe
00 42 31 34 30 48 41 4e 30 36 2e 34 20 0a 00 eb
I do not have access to the datasheet and but it is tested on above
mentioned laptop for a few weeks and seems to work just fine with
timing info of similar panels.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patch.msgid.link/20251203074555.690613-1-alexey.klimov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2c6fde56d ]
There's currently no situation where we want to issue a command to an
AS and not wait for this command to complete. The wait is either
explicitly done (LOCK, UNLOCK) or it's missing (UPDATE). So let's
turn write_cmd() into as_send_cmd_and_wait() that has the wait after
a command is sent.
v2:
- New patch
v3:
- Collect R-b
v4:
- No changes
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://patch.msgid.link/20251128084841.3804658-2-boris.brezillon@collabora.com
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f08cc5b3c ]
The MAP operation for a CPU address mirror VMA does not require ufence
association because such mappings are not GPU-synchronized and do not
participate in GPU job completion signaling.
Remove the unnecessary ufence addition for this case to avoid -EBUSY
failure in check_ufence of unbind ops.
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patch.msgid.link/20251125075628.1182481-6-himal.prasad.ghimiray@intel.com
Signed-off-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6028f59620 ]
xe_vma_userptr_pin_pages can return -EBUSY but -EBUSY has special
meaning in VM bind IOCTLs that user fence is pending that is attached to
the VMA. Convert -EBUSY to -ENOMEM in this case as -EBUSY in practice
means we are low or out of memory.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Link: https://patch.msgid.link/20251122012502.382587-2-matthew.brost@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a579f4b24 ]
Switch the GGTT code to scope-based runtime PM for consistency with
other parts of the driver.
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patch.msgid.link/20251118164338.3572146-51-matthew.d.roper@intel.com
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6ef3d9ff8 ]
imx8m_soc_prepare() directly returns the result of clk_prepare_enable(),
which skips proper cleanup if the clock enable fails. Check the return
value of clk_prepare_enable() and release resources if failure.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202601111406.ZVV3YaiU-lkp@intel.com/
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa93788dd ]
The USB2 port on Smaug is configured for OTG operation but lacked the
required 'usb-role-switch' property, leading to a failed probe and a
non-functioning USB port. Add the property along with setting the default
role to host.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ca2155d6 ]
Intel Amston Lake SoCs with IBECC (In-Band ECC) capability share the same
IBECC registers as Alder Lake-N SoCs. Add two new compute die IDs for
Amston Lake SoC products to enable EDAC support.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Tested-by: Jianfeng Gao <jianfeng.gao@intel.com>
Link: https://patch.msgid.link/20251124065457.3630949-2-qiuxu.zhuo@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c197179990 ]
This reverts commit 06d22ed6b6.
OP-TEE logic in U-Boot automatically injects a reserved-memory
node along with optee firmware node to kernel device tree.
The injection logic is dependent on that there is no manually
defined optee node. Having the node in zynqmp.dtsi effectively
breaks OP-TEE's insertion of the reserved-memory node, causing
memory access violations during runtime.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20251125-revert-zynqmp-optee-v1-1-d2ce4c0fcaf6@vaisala.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fda364cb7 ]
ffa_init() maps the Rx/Tx buffers via ffa_rxtx_map() but on the
partition setup failure path it never unmaps them.
Add the missing ffa_rxtx_unmap() call in the error path so that
the Rx/Tx buffers are properly released before freeing the backing
pages.
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Message-Id: <20251210031656.56194-1-lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05363abc76 ]
In persistent_ram_vmap(), vmap() may return NULL on failure.
If offset is non-zero, adding offset_in_page(start) causes the function
to return a non-NULL pointer even though the mapping failed.
persistent_ram_buffer_map() therefore incorrectly returns success.
Subsequent access to prz->buffer may dereference an invalid address
and cause crashes.
Add proper NULL checking for vmap() failures.
Signed-off-by: Ruipeng Qi <ruipengqi3@gmail.com>
Link: https://patch.msgid.link/20260203020358.3315299-1-ruipengqi3@gmail.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6080fb2116 ]
Updating "ppos" on error conditions does not make much sense. The pattern
is to return the error code directly without modifying the position, or
modify the position on success and return the number of bytes written.
Since on success, the return value of apply is 0, there is no point in
modifying ppos either. Fix it by removing all this and just returning
error code or number of bytes written on success.
Signed-off-by: Joel Fernandes <joelagnelf@nvidia.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Juri Lelli <juri.lelli@redhat.com>
Reviewed-by: Andrea Righi <arighi@nvidia.com>
Acked-by: Tejun Heo <tj@kernel.org>
Tested-by: Christian Loehle <christian.loehle@arm.com>
Link: https://patch.msgid.link/20260126100050.3854740-3-arighi@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1affd29ffb ]
Passing IRQF_ONESHOT ensures that the interrupt source is masked until
the secondary (threaded) handler is done. If only a primary handler is
used then the flag makes no sense because the interrupt can not fire
(again) while its handler is running.
The flag also prevents force-threading of the primary handler and the
irq-core will warn about this.
Remove IRQF_ONESHOT from irqflags.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-10-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03843d95a4 ]
request_threaded_irq() is invoked with a primary and a secondary handler
and no flags are passed. The primary handler is the same as
irq_default_primary_handler() so there is no need to have an identical
copy.
The lack of the IRQF_ONESHOT flag can be dangerous because the interrupt
source is not masked while the threaded handler is active. This means,
especially on LEVEL typed interrupt lines, the interrupt can fire again
before the threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary handler
is done.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-5-bigeasy@linutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ebf35d8f93 ]
Before sending the data via the mailbox to the hardware, to ensure
that the data accessed by the hardware is the most up-to-date,
a write barrier should be added before writing to the mailbox register.
The current memory barrier is placed after writing to the register,
the barrier order should be modified to be before writing to the register.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a7491843 ]
When building selftests/bpf with EXTRA_LDFLAGS=-static the follwoing
error happens:
LINK /ws/linux/tools/testing/selftests/bpf/tools/build/bpftool/bootstrap/bpftool
/usr/bin/x86_64-linux-gnu-ld.bfd: /usr/lib/gcc/x86_64-linux-gnu/15/../../../x86_64-linux-gnu/libcrypto.a(libcrypto-lib-dso_dlfcn.o): in function `dlfcn_globallookup':
[...]
/usr/bin/x86_64-linux-gnu-ld.bfd: /usr/lib/gcc/x86_64-linux-gnu/15/../../../x86_64-linux-gnu/libcrypto.a(libcrypto-lib-c_zlib.o): in function `zlib_oneshot_expand_block':
(.text+0xc64): undefined reference to `uncompress'
/usr/bin/x86_64-linux-gnu-ld.bfd: /usr/lib/gcc/x86_64-linux-gnu/15/../../../x86_64-linux-gnu/libcrypto.a(libcrypto-lib-c_zlib.o): in function `zlib_oneshot_compress_block':
(.text+0xce4): undefined reference to `compress'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:252: /ws/linux/tools/testing/selftests/bpf/tools/build/bpftool/bootstrap/bpftool] Error 1
make: *** [Makefile:327: /ws/linux/tools/testing/selftests/bpf/tools/sbin/bpftool] Error 2
make: *** Waiting for unfinished jobs....
This is caused by wrong order of dependencies in the Makefile. Fix it.
Signed-off-by: Ihor Solodrai <ihor.solodrai@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20260128211255.376933-1-ihor.solodrai@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8d4c6ecb ]
msix_capability_init() fails to unmap the MSI-X region if
msix_setup_interrupts() fails.
Add the missing iounmap() for that error path.
[ tglx: Massaged change log ]
Signed-off-by: Haoxiang Li <lihaoxiang@isrc.iscas.ac.cn>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260125144452.2103812-1-lihaoxiang@isrc.iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1278972b0 ]
The TMU device can be used as both a clocksource and a clockevent
provider. The driver tries to be smart and power itself on and off, as
well as enabling and disabling its clock when it's not in operation.
This behavior is slightly altered if the TMU is used as an early
platform device in which case the device is left powered on after probe,
but the clock is still enabled and disabled at runtime.
This has worked for a long time, but recent improvements in PREEMPT_RT
and PROVE_LOCKING have highlighted an issue. As the TMU registers itself
as a clockevent provider, clockevents_register_device(), it needs to use
raw spinlocks internally as this is the context of which the clockevent
framework interacts with the TMU driver. However in the context of
holding a raw spinlock the TMU driver can't really manage its power
state or clock with calls to pm_runtime_*() and clk_*() as these calls
end up in other platform drivers using regular spinlocks to control
power and clocks.
This mix of spinlock contexts trips a lockdep warning.
=============================
[ BUG: Invalid wait context ]
6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted
-----------------------------
swapper/0/0 is trying to lock:
ffff000008c9e180 (&dev->power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88
other info that might help us debug this:
context-{5:5}
1 lock held by swapper/0/0:
ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0
#0: ffff8000817ec298
ccree e6601000.crypto: ARM ccree device initialized
(tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8
stack backtrace:
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT
Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
Call trace:
show_stack+0x14/0x1c (C)
dump_stack_lvl+0x6c/0x90
dump_stack+0x14/0x1c
__lock_acquire+0x904/0x1584
lock_acquire+0x220/0x34c
_raw_spin_lock_irqsave+0x58/0x80
__pm_runtime_resume+0x38/0x88
sh_tmu_clock_event_set_oneshot+0x84/0xd4
clockevents_switch_state+0xfc/0x13c
tick_broadcast_set_event+0x30/0xa4
__tick_broadcast_oneshot_control+0x1e0/0x3a8
tick_broadcast_oneshot_control+0x30/0x40
cpuidle_enter_state+0x40c/0x680
cpuidle_enter+0x30/0x40
do_idle+0x1f4/0x280
cpu_startup_entry+0x34/0x40
kernel_init+0x0/0x130
do_one_initcall+0x0/0x230
__primary_switched+0x88/0x90
For non-PREEMPT_RT builds this is not really an issue, but for
PREEMPT_RT builds where normal spinlocks can sleep this might be an
issue. Be cautious and always leave the power and clock running after
probe.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251202221341.1856773-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 276f3b6daf ]
Mahe reported issue with bpf_override_return helper not working when
executed from kprobe.multi bpf program on arm.
The problem is that on arm we use alternate storage for pt_regs object
that is passed to bpf_prog_run and if any register is changed (which
is the case of bpf_override_return) it's not propagated back to actual
pt_regs object.
Fixing this by introducing and calling ftrace_partial_regs_update function
to propagate the values of changed registers (ip and stack).
Reported-by: Mahe Tardy <mahe.tardy@gmail.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/bpf/20260112121157.854473-1-jolsa@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4960626f95 ]
I got a report that a task is stuck in perf_event_exit_task() waiting
for global_ctx_data_rwsem. On large systems with lots threads, it'd
have performance issues when it grabs the lock to iterate all threads
in the system to allocate the context data.
And it'd block task exit path which is problematic especially under
memory pressure.
perf_event_open
perf_event_alloc
attach_perf_ctx_data
attach_global_ctx_data
percpu_down_write (global_ctx_data_rwsem)
for_each_process_thread
alloc_task_ctx_data
do_exit
perf_event_exit_task
percpu_down_read (global_ctx_data_rwsem)
It should not hold the global_ctx_data_rwsem on the exit path. Let's
skip allocation for exiting tasks and free the data carefully.
Reported-by: Rosalie Fang <rosaliefang@google.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://patch.msgid.link/20260112165157.1919624-1-namhyung@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1aab1ca57 ]
For a `gotox rX` instruction the rX register should be marked as used
in the compute_insn_live_regs() function. Fix this.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Link: https://lore.kernel.org/r/20260114162544.83253-2-a.s.protopopov@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9f6d30c6 ]
During CPU offlining the interrupts affined to that CPU are moved to other
online CPUs, which might break the original affinity mask if the outgoing
CPU was the last online CPU in that mask. This change is not propagated to
irq_desc::affinity_notify(), which leaves users of the affinity notifier
mechanism with stale information.
Avoid this by scheduling affinity change notification work for interrupts
that were affined to the CPU being offlined, if the new target CPU is not
part of the original affinity mask.
Since irq_set_affinity_locked() uses the same logic to schedule affinity
change notification work, split out this logic into a dedicated function
and use that at both places.
[ tglx: Removed the EXPORT(), removed the !SMP stub, moved the prototype,
added a lockdep assert instead of a comment, fixed up coding style
and name space. Polished and clarified the change log ]
Signed-off-by: Imran Khan <imran.f.khan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260113143727.1041265-1-imran.f.khan@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bffacdb80b ]
cilium bpf_wiregard.bpf.c when compiled with -O1 fails to load
with the following verifier log:
192: (79) r2 = *(u64 *)(r10 -304) ; R2=pkt(r=40) R10=fp0 fp-304=pkt(r=40)
...
227: (85) call bpf_skb_store_bytes#9 ; R0=scalar()
228: (bc) w2 = w0 ; R0=scalar() R2=scalar(smin=0,smax=umax=0xffffffff,var_off=(0x0; 0xffffffff))
229: (c4) w2 s>>= 31 ; R2=scalar(smin=0,smax=umax=0xffffffff,smin32=-1,smax32=0,var_off=(0x0; 0xffffffff))
230: (54) w2 &= -134 ; R2=scalar(smin=0,smax=umax=umax32=0xffffff7a,smax32=0x7fffff7a,var_off=(0x0; 0xffffff7a))
...
232: (66) if w2 s> 0xffffffff goto pc+125 ; R2=scalar(smin=umin=umin32=0x80000000,smax=umax=umax32=0xffffff7a,smax32=-134,var_off=(0x80000000; 0x7fffff7a))
...
238: (79) r4 = *(u64 *)(r10 -304) ; R4=scalar() R10=fp0 fp-304=scalar()
239: (56) if w2 != 0xffffff78 goto pc+210 ; R2=0xffffff78 // -136
...
258: (71) r1 = *(u8 *)(r4 +0)
R4 invalid mem access 'scalar'
The error might confuse most bpf authors, since fp-304 slot had 'pkt'
pointer at insn 192 and became 'scalar' at 238. That happened because
bpf_skb_store_bytes() clears all packet pointers including those in
the stack. On the first glance it might look like a bug in the source
code, since ctx->data pointer should have been reloaded after the call
to bpf_skb_store_bytes().
The relevant part of cilium source code looks like this:
// bpf/lib/nodeport.h
int dsr_set_ipip6()
{
if (ctx_adjust_hroom(...))
return DROP_INVALID; // -134
if (ctx_store_bytes(...))
return DROP_WRITE_ERROR; // -141
return 0;
}
bool dsr_fail_needs_reply(int code)
{
if (code == DROP_FRAG_NEEDED) // -136
return true;
return false;
}
tail_nodeport_ipv6_dsr()
{
ret = dsr_set_ipip6(...);
if (!IS_ERR(ret)) {
...
} else {
if (dsr_fail_needs_reply(ret))
return dsr_reply_icmp6(...);
}
}
The code doesn't have arithmetic shift by 31 and it reloads ctx->data
every time it needs to access it. So it's not a bug in the source code.
The reason is DAGCombiner::foldSelectCCToShiftAnd() LLVM transformation:
// If this is a select where the false operand is zero and the compare is a
// check of the sign bit, see if we can perform the "gzip trick":
// select_cc setlt X, 0, A, 0 -> and (sra X, size(X)-1), A
// select_cc setgt X, 0, A, 0 -> and (not (sra X, size(X)-1)), A
The conditional branch in dsr_set_ipip6() and its return values
are optimized into BPF_ARSH plus BPF_AND:
227: (85) call bpf_skb_store_bytes#9
228: (bc) w2 = w0
229: (c4) w2 s>>= 31 ; R2=scalar(smin=0,smax=umax=0xffffffff,smin32=-1,smax32=0,var_off=(0x0; 0xffffffff))
230: (54) w2 &= -134 ; R2=scalar(smin=0,smax=umax=umax32=0xffffff7a,smax32=0x7fffff7a,var_off=(0x0; 0xffffff7a))
after insn 230 the register w2 can only be 0 or -134,
but the verifier approximates it, since there is no way to
represent two scalars in bpf_reg_state.
After fallthough at insn 232 the w2 can only be -134,
hence the branch at insn
239: (56) if w2 != -136 goto pc+210
should be always taken, and trapping insn 258 should never execute.
LLVM generated correct code, but the verifier follows impossible
path and rejects valid program. To fix this issue recognize this
special LLVM optimization and fork the verifier state.
So after insn 229: (c4) w2 s>>= 31
the verifier has two states to explore:
one with w2 = 0 and another with w2 = 0xffffffff
which makes the verifier accept bpf_wiregard.c
A similar pattern exists were OR operation is used in place of the AND
operation, the verifier detects that pattern as well by forking the
state before the OR operation with a scalar in range [-1,0].
Note there are 20+ such patterns in bpf_wiregard.o compiled
with -O1 and -O2, but they're rarely seen in other production
bpf programs, so push_stack() approach is not a concern.
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Co-developed-by: Puranjay Mohan <puranjay@kernel.org>
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Link: https://lore.kernel.org/r/20260112201424.816836-2-puranjay@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c99d97b466 ]
With CONFIG_CFI enabled, the kernel strictly enforces that indirect
function calls use a function pointer type that matches the
target function. As bpf_kfree_skb() signature differs from the
btf_dtor_kfunc_t pointer type used for the destructor calls in
bpf_obj_free_fields(), add a stub function with the correct type to
fix the type mismatch.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/r/20260110082548.113748-8-samitolvanen@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b40a5d724f ]
With CONFIG_CFI enabled, the kernel strictly enforces that indirect
function calls use a function pointer type that matches the target
function. I ran into the following type mismatch when running BPF
self-tests:
CFI failure at bpf_obj_free_fields+0x190/0x238 (target:
bpf_crypto_ctx_release+0x0/0x94; expected type: 0xa488ebfc)
Internal error: Oops - CFI: 00000000f2008228 [#1] SMP
...
As bpf_crypto_ctx_release() is also used in BPF programs and using
a void pointer as the argument would make the verifier unhappy, add
a simple stub function with the correct type and register it as the
destructor kfunc instead.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Tested-by: Viktor Malik <vmalik@redhat.com>
Link: https://lore.kernel.org/r/20260110082548.113748-7-samitolvanen@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
