This is a tidy up which removes radix MMU calls into the slice
code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The slice_mask cache was a basic conversion which copied the slice
mask into caller's structures, because that's how the original code
worked. In most cases the pointer can be used directly instead, saving
a copy and an on-stack structure.
On POWER8, this increases vfork+exec+exit performance by 0.3%
and reduces time to mmap+munmap a 64kB page by 2%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This code is never compiled in, and it gets broken by the next
patch, so remove it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts the slice_mask bit operation helpers to be the usual
3-operand kind, which allows 2 inputs to set a different output
without an extra copy, which is used in the next patch.
Adds slice_copy_mask, which will be used in the next patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than build slice masks from a range then use that to check for
fit in a candidate mask, implement slice_check_range_fits that checks
if a range fits in a mask directly.
This allows several structures to be removed from stacks, and also we
don't expect a huge range in a lot of these cases, so building and
comparing a full mask is going to be more expensive than testing just
one or two bits of the range.
On POWER8, this increases vfork+exec+exit performance by 0.3%
and reduces time to mmap+munmap a 64kB page by 5%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Calculating the slice mask can become a signifcant overhead for
get_unmapped_area. This patch adds a struct slice_mask for
each page size in the mm_context, and keeps these in synch with
the slices psize arrays and slb_addr_limit.
On Book3S/64 this adds 288 bytes to the mm_context_t for the
slice mask caches.
On POWER8, this increases vfork+exec+exit performance by 9.9%
and reduces time to mmap+munmap a 64kB page by 28%.
Reduces time to mmap+munmap by about 10% on 8xx.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make these loops look the same, and change their form so the
important part is not wrapped over so many lines.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The slice state of an mm gets zeroed then initialised upon exec.
This is the only caller of slice_set_user_psize now, so that can be
removed and instead implement a faster and simplified approach that
requires no locking or checking existing state.
This speeds up vfork+exec+exit performance on POWER8 by 3%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that plpar_wrappers.h has an #ifdef PSERIES we can move the empty
version of plpar_set_ciabr() which xmon wants into there.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 2013 we added some hypercall wrappers which misspelled
"plpar" (P-series Logical PARtition) as "plapr".
Visually they're hard to distinguish and it almost doesn't matter, but
it is confusing when grepping to miss some calls because of the typo.
They've also started spreading, so before they take over let's fix
them all to be "plpar".
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently plpar_wrappers.h is not safe to include when
CONFIG_PPC_PSERIES=n, or at least it can be depending on other config
options and so on.
Fix that by wrapping the entire content in an ifdef.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
smp_query_cpu_stopped() and related #defines are currently in
plpar_wrappers.h. The function actually does an RTAS call, not an
hcall, and basically has nothing to do with plpar_wrappers.h
Move it into pseries.h, where it can easily be used by the only two
callers in pseries/smp.c and pseries/hotplug-cpu.c.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This happens when BMC doesn't return any data and the code is trying
to print the value of data[2].
Getting following crash:
[ 484.728410] Unable to handle kernel NULL pointer dereference at virtual address 00000002
[ 484.736496] pgd = ffff0000094a2000
[ 484.739885] [00000002] *pgd=00000047fcffe003, *pud=00000047fcffd003, *pmd=0000000000000000
[ 484.748158] Internal error: Oops: 96000005 [#1] SMP
[...]
[ 485.101451] Call trace:
[...]
[ 485.188473] [<ffff000000a46e68>] msg_done_handler+0x668/0x700 [ipmi_ssif]
[ 485.195249] [<ffff000000a456b8>] ipmi_ssif_thread+0x110/0x128 [ipmi_ssif]
[ 485.202038] [<ffff0000080f1430>] kthread+0x108/0x138
[ 485.206994] [<ffff0000080838e0>] ret_from_fork+0x10/0x30
[ 485.212294] Code: aa1903e1 aa1803e0 b900227f 95fef6a5 (39400aa3)
Adding a check to validate the data len before printing data[2] to fix this issue.
Signed-off-by: Kamlakant Patel <kamlakant.patel@cavium.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
There are many factors affecting the clock phase, including clock
rate, temperature, logic voltage and silicon process, etc. But clock
rate is the most significant one here, and the driver should be aware
of the change of the clock rate. As mmc controller need a fixed phase
after tuning was completed, at least before explicitly doing re-tune,
so this patch try to restore the clock phase by monitoring the event
of rate change.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
sdhci for rk3399-sapphire works for eMMC but keep-power-in-suspend
is an optional property for SDIO.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Realtek has some sort of "Virtual" IPMI device on the PCI bus as a
KCS controller, but whatever it is, it's not one. Ignore it if seen.
Reported-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Icelake is a next generation Intel platform. Add PCI ID for
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function sc27xx_poweroff_shutdown is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/power/reset/sc27xx-poweroff.c:28:6: warning: symbol
'sc27xx_poweroff_shutdown' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch adds support for DMT display modes over HDMI.
The modes timings configurations are from the Amlogic Vendor linux tree
and tested over multiples monitors.
Previously only a selected number of CEA modes were supported.
Only these following modes are supported with these changes:
- 640x480@60Hz
- 800x600@60Hz
- 1024x768@60Hz
- 1152x864@75Hz
- 1280x1024@60Hz
- 1600x1200@60Hz
- 1920x1080@60Hz
The associated code to handle the clock rates is also added.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1520935670-14187-1-git-send-email-narmstrong@baylibre.com
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the hifi pll to the axg clock controller. This clock maybe used as an
input of the axg audio clock controller. It uses the same settings table
as the gp0 pll but has a frac parameter allowing more precision.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Provide an option for the pll driver to round to the rate closest to the
requested rate, instead of systematically rounding down.
This may allow the provided rate to be closer to the requested rate when
rounding up is not an issue
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the frac parameter for the gp0 pll of the axg and gxl.
This allows to achieve rates between the fixed settings provided
by the table.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finding the appropriate settings of meson plls is too tricky to be done
entirely at runtime, using calculation only. Many combination of m, n
and od won't lock which is why we are using a table for this. However,
for plls having a fractional parameters, it is possible to improve on
the result provided by the table by calculating the frac parameter.
This change adds the calculation of frac when the parameter is available
and the rate provided by the table is not an exact match for the
requested rate.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After testing, it appears that the gxl (and axg) does not require the
special locking/reset loop which was initially added for it.
All the values present in the gxl table can locked with the simple lock
checking loop.
The change switches the gxl and axg gp0 back to the simple lock checking
loop and removes the code no longer required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the missing frac parameter to the meson8b fixed_pll. It seems to be
always on this platform, so the rate remains unchanged
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Revert commit 91eea70e5e (ACPI: battery: Add the ThinkPad "Not
Charging" quirk) as it is reported to cause user space to misbehave.
That appears to be due to bugs in user space, so this commit will go
in again after the bugs have been fixed and the fixes have been
delivered to users.
Link: https://marc.info/?l=linux-acpi&m=152089585129589&w=2
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b cpu_clk has been replaced by a set of divider and mux clocks.
meson_cpu_clk is no longer used and can be removed
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Instead of migrating meson cpu_clk to clk_regmap, like the other meson
clock drivers, we take advantage of the massive rework to get rid of it
completely, and solve (the first part) of the related FIXME notice.
As pointed out in the code comments, the cpu_clk should be modeled with
dividers and muxes it is made of, instead of one big composite clock.
The cpu_clk was not working correctly to enable dvfs on meson8b. It hangs
quite often when changing the cpu clock rate. This new implementation,
based on simple elements improves the situation but the platform will
still hang from time to time. This is not acceptable so, until we can
make the mechanism around the cpu clock stable, the cpu clock subtree
has been put in read-only mode, preventing any change of the cpu clock
The notifier and read-write operation will be added back when we have a
solution to the problem.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson audio divider driver to use clk_regmap and move gxbb
clock using meson_clk_audio_divider to clk_regmap.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson mpll driver to use clk_regmap and move meson8b, gxbb
and axg clocks using meson_clk_mpll to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock drivers are using struct parm to describe each field of the
clock provider. Providing helpers to access these fields with regmap
helps to keep drivers readable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_mux to clk_regmap
Also remove a few useless tables in the process
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_divider to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_gate to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
aoclk_gate_regmap has been replaced by meson's clk_regmap.
It is no longer necessary so, remove it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the gxbb ao specific regmap based clock and use the
meson clk_regmap based clock instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock controllers need to move the classical iomem registers to
regmap. This is triggered because the HHI controllers found on the GXBB
and GXL host more than just clocks. To properly handle this, we would
like to migrate HHI to syscon. Also GXBB AO clock controller already use
regmap, AXG AO and Audio clock controllers will as well.
The purpose of this change is to provide a common structure to these
meson controllers (and possibly others) for regmap based clocks.
This change provides the basic gate, mux and divider, based on the
helpers provided by the related generic clocks
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>