Commit graph

1,059,104 commits

Author SHA1 Message Date
Eugen Hristev
9d464cc5ac ARM: at91: sama7: introduce sama7 SoC family
Introduce new family of SoCs, sama7, and first SoC, sama7g5.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: keep only the sama7_dt]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-23-claudiu.beznea@microchip.com
2021-07-19 14:32:13 +02:00
Claudiu Beznea
ccdbdf33bd ARM: at91: pm: add sama7g5's pmc
Add SAMA7G5's PMC to compatible list.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-22-claudiu.beznea@microchip.com
2021-07-19 14:32:13 +02:00
Claudiu Beznea
f205adb608 ARM: at91: pm: add backup mode support for SAMA7G5
Adapt at91_pm_backup_init() to work for SAMA7G5. Also, set the LPM pin
to shutdown controller. This will signal to PMIC that it needs to switch
to the state corresponding to backup mode.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-21-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
d2d4716d83 ARM: at91: pm: save ddr phy calibration data to securam
The resuming from backup mode is done with the help of bootloader.
The bootloader reconfigure the DDR controller and DDR PHY controller.
To speed-up the resuming process save the PHY calibration data into
SECURAM before suspending (securam is powered on backup mode).
This data will be later used by bootloader in DDR PHY reconfiguration
process. Also, in the process or recalibration the first 8 words of
the memory may get corrupted. To solve this, these 8 words are saved
in the securam and restored by bootloader in the process of PHY
configuration.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-20-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
892e1f4a3a ARM: at91: pm: add sama7g5 ddr phy controller
SAMA7G5 self-refresh procedure accesses also the DDR PHY registers.
Adapt the code so that the at91_dt_ramc() to look also for DDR PHYs,
in case it is mandatory.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-19-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
2c26cb4d69 ARM: at91: pm: add sama7g5 ddr controller
Add SAMA7G5 DDR controller to the list of DDR controller compatibles.
At the moment there is no standby support. Adapt the code for this.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-18-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
5b0bef872c ARM: at91: pm: wait for ddr power mode off
Wait for DDR power mode off before shutting down the core.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-16-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
475be50fc1 ARM: at91: pm: add support for 2.5V LDO regulator control
Add support to disable/enable 2.5V LDO regulator when entering/exiting
any ULP mode.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-15-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
28eb1d40fe ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
Add support for MCK1..4 save restore for ULP modes.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-14-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
f0bbf17958 ARM: at91: pm: add self-refresh support for sama7g5
Add self-refresh support for SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-13-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
d8c7983f31 ARM: at91: ddr: add registers definitions for sama7g5's ddr
Add registers and bits definitions for SAMA7G5's UDDRC and DDR3PHY.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-12-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
96abf16861 ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
Add SFRBU registers definitions for SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-11-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
15126bb61b ARM: at91: pm: add support for waiting MCK1..4
SAMA7G5 has 5 master clocks 0..4. MCK0 is controlled differently than
MCK 1..4. MCK 1..4 should also be saved/restored in the last phase of
suspend/resume. Thus, adapt wait_mckrdy to support also MCK1..4.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-10-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
e3821ed476 ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
Replace CONFIG_SOC_SAM9X60 with CONFIG_HAVE_AT91_SAM9X60_PLL as the
SAM9X60's PLL is also present on SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-9-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
87e1b30c29 ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
For the previous AT91 RAM controller and self-refresh procedure this
had no side effects. However, for SAMA7G5 the self-refresh procedure
doesn't allow this anymore as the RAM controller ports are closed
before switching it to self-refresh. This commits prepares the code
for the following ones adding self-refresh and PM support for SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-8-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
29cdf077a9 ARM: at91: pm: use r7 instead of tmp1
Use r7 instead of tmp1 in macros. This prepares the filed for
next commits.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-7-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
629ba8ee03 ARM: at91: pm: do not initialize pdev
There is no need to initialize pdev.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-6-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea
404956f47c ARM: at91: pm: check for different controllers in at91_pm_modes_init()
at91_pm_modes_init() checks for proper nodes in device tree and maps
them accordingly. Up to SAMA7G5 all AT91 SoCs had the same mapping
b/w power saving modes and different controllers needed in the
final/first steps of suspend/resume. SAMA7G5 is not aligned with the
old SoCs thus the code is adapted for this. This patch prepares
the field for next commits.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-5-claudiu.beznea@microchip.com
2021-07-19 14:32:11 +02:00
Claudiu Beznea
0a7a2443c7 ARM: at91: pm: document at91_soc_pm structure
Document at91_soc_pm structure.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-4-claudiu.beznea@microchip.com
2021-07-19 14:32:11 +02:00
Claudiu Beznea
fe4c09e568 ARM: at91: pm: move the setup of soc_pm.bu->suspended
Move the setup of soc_pm.bu->suspended in platform_suspend::begin
function so that the PMC code in charge with clocks suspend/resume
to differentiate b/w standard PM mode and backup mode.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-3-claudiu.beznea@microchip.com
2021-07-19 14:32:11 +02:00
Claudiu Beznea
f19dd1df9e ARM: at91: pm: move pm_bu to soc_pm data structure
Move pm_bu to soc_pm data structure.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-2-claudiu.beznea@microchip.com
2021-07-19 14:32:11 +02:00
Eugen Hristev
577cb67ad9 ARM: at91: debug: add sama7g5 low level debug uart
Add sama7g5 SoC debug uart on Flexcom3. This is the UART that the
ROM bootloader uses.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210409113116.482199-2-eugen.hristev@microchip.com
2021-07-19 14:32:11 +02:00
Eugen Hristev
56bc296591 ARM: at91: add new SoC sama7g5
Add new SoC from at91 family : sama7g5

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: Select PLL, generic clock and UTMI support, add PM configs]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210409113116.482199-1-eugen.hristev@microchip.com
Link: https://lore.kernel.org/r/20210719080317.1045832-2-claudiu.beznea@microchip.com
2021-07-19 14:32:11 +02:00
Claudiu Beznea
ec03f18cc2 clk: at91: add register definition for sama7g5's master clock
Add register definitions for SAMA7G5's master clock. These would be
also used by architecture specific power saving code.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210719080317.1045832-3-claudiu.beznea@microchip.com
2021-07-19 14:28:56 +02:00
Uwe Kleine-König
bd9616996b
spi: imx: Simplify logic in spi_imx_push()
For each usage of fifo_words it is clear if ->dynamic_burst is true or
not. This can be used to simplify the function a bit.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210716173927.2050620-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:55 +01:00
Andy Shevchenko
3bbdc08326
spi: pxa2xx: Reuse int_stop_and_reset() in couple of places
Reuse int_stop_and_reset() in couple of places.

While at it, change the order of the int_stop_and_reset() and pxa2xx_spi_off()
to be in align with the similar flow in int_error_stop().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210719074842.36060-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:54 +01:00
Andy Shevchenko
cdcb26ce74
spi: pxa2xx: Reset DMA bits in CR1 in reset_sccr1()
In order to allow reset_sccr1() to be reused in DMA paths,
reset DMA bits in CR1 in this function.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210719074842.36060-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:53 +01:00
Andy Shevchenko
e0a6512d29
spi: pxa2xx: Convert reset_sccr1() to use pxa2xx_spi_update()
Convert reset_sccr1() to use pxa2xx_spi_update().
It will help for further improvements.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210719074842.36060-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:52 +01:00
Colin Ian King
f020e4d0b4
regulator: Fix a couple of spelling mistakes in Kconfig
There are a couple of spelling mistakes in the Kconfig text. Fix them.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210719103429.15544-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:50 +01:00
Marek Vasut
56912da7a6
spi: cadence: Correct initialisation of runtime PM again
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.

Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.

Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:44 +01:00
Peter Ujfalusi
82d28b67f7
ASoC: ti: j721e-evm: Check for not initialized parent_clk_id
During probe the parent_clk_id is set to -1 which should not be used to
array index within hsdiv_rates[].

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-3-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:42 +01:00
Peter Ujfalusi
78d2a05ef2
ASoC: ti: j721e-evm: Fix unbalanced domain activity tracking during startup
In case of an error within j721e_audio_startup() the domain->active must
be decremented to avoid unbalanced counter.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-2-peter.ujfalusi@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
2021-07-19 12:58:41 +01:00
Joe Perches
e98b461bb0 MIPS: octeon: Remove vestiges of CONFIG_CAVIUM_RESERVE32
The config option CAVIUM_RESERVE32 is not used.
Remove the dead code controlled by it.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2021-07-19 13:17:20 +02:00
周琰杰 (Zhou Yanjie)
14d72af7ab MIPS: Ingenic: Add system type for new Ingenic SoCs.
Add JZ4730, JZ4750, JZ4755, JZ4760, JZ4760B, X2000H, and X2100 system
type for cat /proc/cpuinfo to give out JZ4730, JZ4750, JZ4755, JZ4760,
JZ4760B, X2000H, and X2100.

Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2021-07-19 13:16:42 +02:00
Pavel Skripkin
761608f5cf m68k: emu: Fix invalid free in nfeth_cleanup()
In the for loop all nfeth_dev array members should be freed, not only
the first one.  Freeing only the first array member can cause
double-free bugs and memory leaks.

Fixes: 9cd7b14831 ("m68k/atari: ARAnyM - Add support for network access")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210705204727.10743-1-paskripkin@gmail.com
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2021-07-19 12:20:33 +02:00
Geert Uytterhoeven
21ed492659 m68k: MAC should select HAVE_PATA_PLATFORM
The defconfigs switched Mac from the deprecated CONFIG_BLK_DEV_PLATFORM
to CONFIG_PATA_PLATFORM.  However, the latter depends on
CONFIG_HAVE_PATA_PLATFORM, which thus must be selected first.

Fixes: b90257bfdd ("m68k: use libata instead of the legacy ide driver")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210712074022.2116655-1-geert@linux-m68k.org
2021-07-19 12:18:42 +02:00
Chris Down
ad7d61f159 printk: index: Add indexing support to dev_printk
While for most kinds of issues we have counters, tracepoints, or metrics
with a stable interface which can reliably be used to indicate issues,
in order to react to production issues quickly we sometimes need to work
with the interface which most kernel developers naturally use when
developing: printk, and printk-esques like dev_printk.

dev_printk is by far the most likely custom subsystem printk to benefit
from the printk indexing infrastructure, since niche device issues
brought about by production changes, firmware upgrades, and the like are
one of the most common things that we need printk infrastructure's
assistance to monitor.

Often these errors were never expected to practically manifest in
reality, and exhibit in code without extensive (or any) metrics present.
As such, there are typically very few options for issue detection
available to those with large fleets at the time the incident happens,
and we thus benefit strongly from monitoring netconsole in these
instances.

As such, add the infrastructure for dev_printk to be indexed in the
printk index. Even on a minimal kernel config, the coverage of the base
kernel's printk index is significantly improved:

Before:

    [root@ktst ~]# wc -l /sys/kernel/debug/printk/index/vmlinux
    4497 /sys/kernel/debug/printk/index/vmlinux

After:

    [root@ktst ~]# wc -l /sys/kernel/debug/printk/index/vmlinux
    5573 /sys/kernel/debug/printk/index/vmlinux

In terms of implementation, in order to trivially disambiguate them,
dev_printk is now a macro which wraps _dev_printk.

Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/959c7aed1017cb2c9de922e0a820d397e29c6a5a.1623775748.git.chris@chrisdown.name
2021-07-19 12:13:06 +02:00
Chris Down
3370155737 printk: Userspace format indexing support
We have a number of systems industry-wide that have a subset of their
functionality that works as follows:

1. Receive a message from local kmsg, serial console, or netconsole;
2. Apply a set of rules to classify the message;
3. Do something based on this classification (like scheduling a
   remediation for the machine), rinse, and repeat.

As a couple of examples of places we have this implemented just inside
Facebook, although this isn't a Facebook-specific problem, we have this
inside our netconsole processing (for alarm classification), and as part
of our machine health checking. We use these messages to determine
fairly important metrics around production health, and it's important
that we get them right.

While for some kinds of issues we have counters, tracepoints, or metrics
with a stable interface which can reliably indicate the issue, in order
to react to production issues quickly we need to work with the interface
which most kernel developers naturally use when developing: printk.

Most production issues come from unexpected phenomena, and as such
usually the code in question doesn't have easily usable tracepoints or
other counters available for the specific problem being mitigated. We
have a number of lines of monitoring defence against problems in
production (host metrics, process metrics, service metrics, etc), and
where it's not feasible to reliably monitor at another level, this kind
of pragmatic netconsole monitoring is essential.

As one would expect, monitoring using printk is rather brittle for a
number of reasons -- most notably that the message might disappear
entirely in a new version of the kernel, or that the message may change
in some way that the regex or other classification methods start to
silently fail.

One factor that makes this even harder is that, under normal operation,
many of these messages are never expected to be hit. For example, there
may be a rare hardware bug which one wants to detect if it was to ever
happen again, but its recurrence is not likely or anticipated. This
precludes using something like checking whether the printk in question
was printed somewhere fleetwide recently to determine whether the
message in question is still present or not, since we don't anticipate
that it should be printed anywhere, but still need to monitor for its
future presence in the long-term.

This class of issue has happened on a number of occasions, causing
unhealthy machines with hardware issues to remain in production for
longer than ideal. As a recent example, some monitoring around
blk_update_request fell out of date and caused semi-broken machines to
remain in production for longer than would be desirable.

Searching through the codebase to find the message is also extremely
fragile, because many of the messages are further constructed beyond
their callsite (eg. btrfs_printk and other module-specific wrappers,
each with their own functionality). Even if they aren't, guessing the
format and formulation of the underlying message based on the aesthetics
of the message emitted is not a recipe for success at scale, and our
previous issues with fleetwide machine health checking demonstrate as
much.

This provides a solution to the issue of silently changed or deleted
printks: we record pointers to all printk format strings known at
compile time into a new .printk_index section, both in vmlinux and
modules. At runtime, this can then be iterated by looking at
<debugfs>/printk/index/<module>, which emits the following format, both
readable by humans and able to be parsed by machines:

    $ head -1 vmlinux; shuf -n 5 vmlinux
    # <level[,flags]> filename:line function "format"
    <5> block/blk-settings.c:661 disk_stack_limits "%s: Warning: Device %s is misaligned\n"
    <4> kernel/trace/trace.c:8296 trace_create_file "Could not create tracefs '%s' entry\n"
    <6> arch/x86/kernel/hpet.c:144 _hpet_print_config "hpet: %s(%d):\n"
    <6> init/do_mounts.c:605 prepare_namespace "Waiting for root device %s...\n"
    <6> drivers/acpi/osl.c:1410 acpi_no_auto_serialize_setup "ACPI: auto-serialization disabled\n"

This mitigates the majority of cases where we have a highly-specific
printk which we want to match on, as we can now enumerate and check
whether the format changed or the printk callsite disappeared entirely
in userspace. This allows us to catch changes to printks we monitor
earlier and decide what to do about it before it becomes problematic.

There is no additional runtime cost for printk callers or printk itself,
and the assembly generated is exactly the same.

Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Tested-by: Petr Mladek <pmladek@suse.com>
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jessica Yu <jeyu@kernel.org> # for module.{c,h}
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/e42070983637ac5e384f17fbdbe86d19c7b212a5.1623775748.git.chris@chrisdown.name
2021-07-19 11:57:48 +02:00
Chris Down
f3d75cf537 printk: Rework parse_prefix into printk_parse_prefix
parse_prefix is needed externally by later patches, so move it into a
context where it can be used as such. Also give it the printk_ prefix to
reduce the chance of collisions.

Signed-off-by: Chris Down <chris@chrisdown.name>
Cc: Petr Mladek <pmladek@suse.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/b22ba314a860e5c7f887958f1eab2649f9bd1d06.1623775748.git.chris@chrisdown.name
2021-07-19 11:57:18 +02:00
Chris Down
a1ad4b8a19 printk: Straighten out log_flags into printk_info_flags
In the past, `enum log_flags` was part of `struct log`, hence the name.
`struct log` has since been reworked and now this struct is stored
inside `struct printk_info`. However, the name was never updated, which
is somewhat confusing -- especially since these flags operate at the
record level rather than at the level of an abstract log.

printk_info_flags also joins its other metadata struct friends in
printk_ringbuffer.h.

Signed-off-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/3dd801982f02603e6e3aa4f8bc4f5ebb830a4949.1623775748.git.chris@chrisdown.name
2021-07-19 11:56:40 +02:00
Chris Down
91027d0a7a string_helpers: Escape double quotes in escape_special
From an abstract point of view, escape_special's counterpart,
unescape_special, already handles the unescaping of blackslashed double
quote sequences.

As a more practical example, printk indexing is an example case where
this is already practically useful. Compare an example with
`ESCAPE_SPECIAL | ESCAPE_SPACE`, with quotes not escaped:

    [root@ktst ~]# grep drivers/pci/pci-stub.c:69 /sys/kernel/debug/printk/index/vmlinux
    <4> drivers/pci/pci-stub.c:69 pci_stub_init "pci-stub: invalid ID string "%s"\n"

...and the same after this patch:

    [root@ktst ~]# grep drivers/pci/pci-stub.c:69 /sys/kernel/debug/printk/index/vmlinux
    <4> drivers/pci/pci-stub.c:69 pci_stub_init "pci-stub: invalid ID string \"%s\"\n"

One can of course, alternatively, use ESCAPE_APPEND with a quote in
@only, but without this patch quotes are coerced into hex or octal which
can hurt readability quite significantly.

I've checked uses of ESCAPE_SPECIAL and %pE across the codebase, and I'm
pretty confident that this shouldn't affect any stable interfaces.

Signed-off-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/af144c5b75e41ce417386253ba2694456bc04118.1623775748.git.chris@chrisdown.name
2021-07-19 11:39:28 +02:00
Haiyang Zhang
7c9ff3deee Drivers: hv: vmbus: Fix duplicate CPU assignments within a device
The vmbus module uses a rotational algorithm to assign target CPUs to
a device's channels. Depending on the timing of different device's channel
offers, different channels of a device may be assigned to the same CPU.

For example on a VM with 2 CPUs, if NIC A and B's channels are offered
in the following order, NIC A will have both channels on CPU0, and
NIC B will have both channels on CPU1 -- see below. This kind of
assignment causes RSS load that is spreading across different channels
to end up on the same CPU.

Timing of channel offers:
NIC A channel 0
NIC B channel 0
NIC A channel 1
NIC B channel 1

VMBUS ID 14: Class_ID = {f8615163-df3e-46c5-913f-f2d2f965ed0e} - Synthetic network adapter
        Device_ID = {cab064cd-1f31-47d5-a8b4-9d57e320cccd}
        Sysfs path: /sys/bus/vmbus/devices/cab064cd-1f31-47d5-a8b4-9d57e320cccd
        Rel_ID=14, target_cpu=0
        Rel_ID=17, target_cpu=0

VMBUS ID 16: Class_ID = {f8615163-df3e-46c5-913f-f2d2f965ed0e} - Synthetic network adapter
        Device_ID = {244225ca-743e-4020-a17d-d7baa13d6cea}
        Sysfs path: /sys/bus/vmbus/devices/244225ca-743e-4020-a17d-d7baa13d6cea
        Rel_ID=16, target_cpu=1
        Rel_ID=18, target_cpu=1

Update the vmbus CPU assignment algorithm to avoid duplicate CPU
assignments within a device.

The new algorithm iterates num_online_cpus + 1 times.
The existing rotational algorithm to find "next NUMA & CPU" is still here.
But if the resulting CPU is already used by the same device, it will try
the next CPU.
In the last iteration, it assigns the channel to the next available CPU
like the existing algorithm. This is not normally expected, because
during device probe, we limit the number of channels of a device to
be <= number of online CPUs.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1626459673-17420-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-07-19 09:26:31 +00:00
Michael Kelley
31e5e64694 drivers: hv: Decouple Hyper-V clock/timer code from VMbus drivers
Hyper-V clock/timer code in hyperv_timer.c is mostly independent from
other VMbus drivers, but building for ARM64 without hyperv_timer.c
shows some remaining entanglements.  A default implementation of
hv_read_reference_counter can just read a Hyper-V synthetic register
and be independent of hyperv_timer.c, so move this code out and into
hv_common.c. Then it can be used by the timesync driver even if
hyperv_timer.c isn't built on a particular architecture.  If
hyperv_timer.c *is* built, it can override with a faster implementation.

Also provide stubs for stimer functions called by the VMbus driver when
hyperv_timer.c isn't built.

No functional changes.

Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1626220906-22629-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-07-19 09:24:28 +00:00
Lad Prabhakar
1b87d5bba3 clk: renesas: r9a07g044: Add clock and reset entries for ADC
Add clock and reset entries for ADC block in CPG driver.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210719085840.21842-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 11:22:23 +02:00
Lad Prabhakar
3b5c734592 clk: renesas: r9a07g044: Add clock and reset entries for CANFD
Add clock and reset entries for CANFD in CPG driver.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210715182123.23372-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 11:22:21 +02:00
Geert Uytterhoeven
0aae437ac5 clk: renesas: Rename renesas-rzg2l-cpg.[ch] to rzg2l-cpg.[ch]
Rename renesas-rzg2l-cpg.c and renesas-rzg2l-cpg.h to rzg2l-cpg.c resp.
rzg2l-cpg.h, for consistency with other (sub)drivers.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/edc442daaedffcf10e835ff479d906fcae0e59db.1626268821.git.geert+renesas@glider.be
2021-07-19 11:22:20 +02:00
Lad Prabhakar
d85b82f09a clk: renesas: r9a07g044: Add GPIO clock and reset entries
Add GPIO clock and reset entries in CPG driver.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210712194422.12405-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 11:22:10 +02:00
Biju Das
d520af3451 clk: renesas: r9a07g044: Add SSIF-2 clock and reset entries
Add SSIF-2 clock and reset entries in CPG driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210702135010.5937-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 10:53:53 +02:00
Biju Das
03fa6e4b26 clk: renesas: r9a07g044: Add USB clocks/resets
Add clock/reset entries for USB PHY control, USB2.0 host and device.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210630073013.22415-5-biju.das.jz@bp.renesas.com
[geert: s/usb0_device/usb0_func]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 10:53:53 +02:00
Biju Das
eb829e549b clk: renesas: r9a07g044: Add DMAC clocks/resets
Add DMAC clock and reset entries in CPG driver.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210626081344.5783-10-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-07-19 10:53:53 +02:00