This adds code to the radix hypervisor page fault handler to handle the
case where the guest memory is backed by 1GB hugepages, and put them
into the partition-scoped radix tree at the PUD level. The code is
essentially analogous to the code for 2MB pages. This also rearranges
kvmppc_create_pte() to make it easier to follow.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
When using the radix MMU, we can get hypervisor page fault interrupts
with the DSISR_SET_RC bit set in DSISR/HSRR1, indicating that an
attempt to set the R (reference) or C (change) bit in a PTE atomically
failed. Previously we would find the corresponding Linux PTE and
check the permission and dirty bits there, but this is not really
necessary since we only need to do what the hardware was trying to
do, namely set R or C atomically. This removes the code that reads
the Linux PTE and just update the partition-scoped PTE, having first
checked that it is still present, and if the access is a write, that
the PTE still has write permission.
Furthermore, we now check whether any other relevant bits are set
in DSISR, and if there are, then we proceed with the rest of the
function in order to handle whatever condition they represent,
instead of returning to the guest as we did previously.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This improves the handling of transparent huge pages in the radix
hypervisor page fault handler. Previously, if a small page is faulted
in to a 2MB region of guest physical space, that means that there is
a page table pointer at the PMD level, which could never be replaced
by a leaf (2MB) PMD entry. This adds the code to clear the PMD,
invlidate the page walk cache and free the page table page in this
situation, so that the leaf PMD entry can be created.
This also adds code to check whether a PMD or PTE being inserted is
the same as is already there (because of a race with another CPU that
faulted on the same page) and if so, we don't replace the existing
entry, meaning that we don't invalidate the PTE or PMD and do a TLB
invalidation.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since commit fb1522e099 ("KVM: update to new mmu_notifier semantic
v2", 2017-08-31), the MMU notifier code in KVM no longer calls the
kvm_unmap_hva callback. This removes the PPC implementations of
kvm_unmap_hva().
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The cpufreq core is already validating the CPU frequency table after
calling the ->init() callback of the cpufreq drivers and the drivers
don't need to do the same anymore. Though they need to set the
policy->freq_table field directly from the ->init() callback now.
Stop validating the frequency table from powernv driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
RAPL MSRs and handling for Cannon Lake are similar to Sky Lake
and Kaby Lake.
Signed-off-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device referred to by ACPI LPI constrains (coming from function 1
of the Low Power S0 Idle _DSM interface) is not power-manageable via
ACPI (no _PS0 method and no power resources), the code generating
diagnostic information for the LPI constraints will print a message
about that to the kernel log on every system suspend-resume cycle
(possibly for multiple times).
That is not very useful and noisy, so modify that code to disregard
the LPI list entries corresponding to the devices that are not power-
manageable after printing that information for them once.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fix grammar and punctuation (end sentences with a period) in the
Kconfig help text for ACPI_PROCFS_POWER.
I was looking at this since it appears to be going away (again,
some day) and I have a working script that uses this info to tell me
battery usage. I can update the script to use /sys/class/power_supply
(in theory) but the contents (with units) should be documented in
Documentation/ABI/ before /proc/acpi/battery/ is removed (IMO).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can return directly at the beginning of the function and save the 'err'
label.
We can also explicitly return 0 when the probe succeed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Avoid some code ducplication and be more future-proof.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A number of Dell systems require an OEM _OSI string "Linux-Dell-Video"
as a BIOS workaround to disable RTD3 which causes systems hangs when
NVidia graphics cards are installed. The affected Dell systems are
with system IDs: 0818, 0819, 0820, 0850, 0851, 086F, 0870, 0885 and
0886.
The form of the OEM _OSI strings is defined by each OEMs and is
discussed in Documentation/acpi/osi.txt.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The H3 has an ARM Mali 400 GPU, so add binding to our DT.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The property pinctrl-names is totally superfluous. It would be good to
remove the property to keep the node neatness. There is actually
unnecessary to set up any pins for data path TRGMII between main SoC and
MT7530. Furthermore, it's more reasonable for the pin setup of control
path MDIO bus is being placed inside the node of ethernet controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
On bpi-r2 board, totally there're four UARTs which we usually called
uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has
dedicated pin slot which is used to console log. uart[0-1] appear at the
40-pins connector and uart3 has no pinout, but just has test points (TP47
for TX and TP48 for RX, respectively) nearby uart2, but we don't enable
uart3 in the patch. The missing pinctrl is also being supplemented for
those newly added devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Both mmc devices on bananapi-r2 board should all use the fixed regulators
as their power source instead of PMIC MT6323 exports.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Reported-by: David Ahern <dsahern@gmail.com>
Fixes: 1fad59ea1c ("selftests: pmtu: Add pmtu_vti6_link_change_mtu test")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Automatic PHY interrupts
Now that the mv88e6xxx driver either installs in interrupt handler, or
polls for interrupts, it is possible to always handle PHY interrupts,
rather than have phylib perform the polling. This speeds up detection
of link changes and reduces the load on the MDIO bus, which is
beneficial for PTP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.
Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to the info structure the number of internal PHYs, if they generate
interrupts. Some of the older generations of switches have internal
PHYs, but no interrupt registers. In this case, set the count to zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to polling for interrupts, it is important that
the number of global 1 interrupts is listed. Without it, the driver
requests an interrupt domain for zero interrupts, which returns
EINVAL, and the probe fails.
Add two missing entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can hit the register lock not held assertion with the following path:
[ 34.170631] mv88e6085 0.1:00: Switch registers lock not held!
[ 34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143
[ 34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 34.189519] Backtrace:
[ 34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24)
[ 34.199680] r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000
[ 34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28)
[ 34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c)
[ 34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c)
[ 34.229257] r5:a09cd128 r4:9ee31d07
[ 34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64)
[ 34.242690] r4:9f5dc010
[ 34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c)
[ 34.255389] r4:00000001
[ 34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0)
[ 34.268156] r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c
[ 34.276052] r4:9f5dc010
[ 34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4)
mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both
chip->info->ops->stats_get_stats(), which holds the register lock, and
chip->info->ops->serdes_get_stats() which does not. Have
chip->info->ops->serdes_get_stats() be running with the register lock held to
avoid such assertions.
Fixes: 436fe17d27 ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ethsys, pciesys and ssusbsys internally include reset controller, so
explicitly add back these missing cell definitions to related bindings
and examples.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
When unbinding/removing the driver, we will run into the following warnings:
[ 259.655198] fec 400d1000.ethernet: 400d1000.ethernet supply phy not found, using dummy regulator
[ 259.665065] fec 400d1000.ethernet: Unbalanced pm_runtime_enable!
[ 259.672770] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
[ 259.683062] fec 400d1000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: f2:3e:93:b7:29:c1
[ 259.696239] libphy: fec_enet_mii_bus: probed
Avoid these warnings by balancing the runtime PM calls during fec_drv_remove().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner H6 SoC has a CCU which has been largely rearranged.
Add support for it in the sunxi-ng CCU framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Allwinner H6 main CCU uses the internal oscillator of the SoC, which
is different with old SoCs' main CCU.
Add device tree binding for the Allwinner H6 main CCU.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the new Allwinner H6 SoC, multiple PLL's are NMP style clocks
(modelled as NKMP with no K) and have fixed post-dividers.
Add fixed post divider support to the NKMP style clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pull x86/pti updates from Thomas Gleixner:
"Another set of melted spectrum updates:
- Iron out the last late microcode loading issues by actually
checking whether new microcode is present and preventing the CPU
synchronization to run into a timeout induced hang.
- Remove Skylake C2 from the microcode blacklist according to the
latest Intel documentation
- Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
not. Enhance the selftests to catch that kind of issue
- Annotate indirect calls/jumps for objtool on 32bit. This is not a
functional issue, but for consistency sake its the right thing to
do.
- Fix a jump label build warning observed on SPARC64 which uses 32bit
storage for the code location which is casted to 64 bit pointer w/o
extending it to 64bit first.
- Add two new cpufeature bits. Not really an urgent issue, but
provides them for both x86 and x86/kvm work. No impact on the
current kernel"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Fix CPU synchronization routine
x86/microcode: Attempt late loading only when new microcode is present
x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
jump_label: Fix sparc64 warning
x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
x86/vm86/32: Fix POPF emulation
selftests/x86/entry_from_vm86: Add test cases for POPF
selftests/x86/entry_from_vm86: Exit with 1 if we fail
x86/cpufeatures: Add Intel PCONFIG cpufeature
x86/cpufeatures: Add Intel Total Memory Encryption cpufeature
Pull x86 fix from Thomas Gleixner:
"A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
this results in a crash as p*d_huge() returns 0 in that case"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault to use pXd_large
Pull irq fixes from Thomas Gleixner:
"Three fixes for irq chip drivers:
- Make sure the allocations in the GIC-V3 ITS driver are large enough
to accomodate the interrupt space
- Fix a misplaced __iomem annotation which causes a splat of 26
sparse warnings
- Remove an unused function in the IMX GPCV2 driver which causes
build warnings"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-imx-gpcv2: Remove unused function
irqchip/gic-v3-its: Ensure nr_ites >= nr_lpis
irqchip/gic-v3-its: Fix misplaced __iomem annotations
Pull EFI fix from Thomas Gleixner:
"A single fix to prevent partially initialized pointers in mixed mode
(64bit kernel on 32bit UEFI)"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/tpm: Initialize pointer variables to zero for mixed mode
Version 20180313.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This prepares the code for eventual removal of the original
style of deferred execution of the MLC.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This ensures that acpi_ev_fixed_event_detect() does not use fixed_status
and and fixed_enable as uninitialized variables.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
lockups on POWER9.
* ARM: locking fix, reset fix, GICv2 multi-source SGI injection fix,
GICv2-on-v3 MMIO synchronization fix, make the console less verbose.
* x86: fix device passthrough on AMD SME.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJariCQAAoJEL/70l94x66D6j4H/iS51f1EFRjTXbM+/D0BxpOD
hTz3tiV4JNezwXkxm9FMr7e5sfONTsqZodzCeXbz9XRmb6lwkEIbaPC4G2ALJeBH
V1Gpy2NsoBNCaU6Ci7SGqs1PG7wmG1tGMkzgkUoi2mwJRbA7UfnPmL1bTRESc4/w
oYN5xPj1/bLYWnok2cEJevND2VUTy+/dazpm+9gZzHqeoBnRRhhNluLW11A7yi2U
mSxAZrCH8X9EejIEhU8jAah4PYZ9tP8TmvUcnAPYpNgDh2JH6tlkGAYSbpadiCvf
FJNhtev67uDL1jPzqQJLNo5Z04cg06M+9cYqrLD1q287LXsKs+LHXJY/AI56oIM=
=YHkv
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"PPC:
- fix bug leading to lost IPIs and smp_call_function_many() lockups
on POWER9
ARM:
- locking fix
- reset fix
- GICv2 multi-source SGI injection fix
- GICv2-on-v3 MMIO synchronization fix
- make the console less verbose.
x86:
- fix device passthrough on AMD SME"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix device passthrough when SME is active
kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
KVM: arm/arm64: Reduce verbosity of KVM init log
KVM: arm/arm64: Reset mapped IRQs on VM reset
KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry
Was acpi_gbl_parse_table_as_term_list, changed to:
acpi_gbl_execute_tables_as_methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixing the ACPI_ERROR_NAMESPACE macros created an "unused variable"
compile error when ACPI_NO_ERROR_MESSAGES was defined. This commit
also fixes the above compilation errors by surrounding variables
meant for debugging inside a new ACPI_ERROR_ONLY macro.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the option to ignore package resolution errors into
a runtime option.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the documentatuon above its declaration indicates, acpi_get_object_info()
is intended for early probe usage and as such should not call any methods
which may rely on op_regions, before this commit it was also calling _STA,
which on some systems does rely on op_regions.
Calling _STA before things are ready leads to errors such as these
(under Linux, on some hardware):
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[generic_serial_bus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region generic_serial_bus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
End 2015 support for the _SUB method was removed for exactly the same
reason. Removing current_status from struct acpi_device_info only has a limited
impact. Within ACPICA it is only used by 2 debug messages, both
of which are modified to no longer print it with this commit.
Outside of ACPICA, there was one user in Linux, which has been patched to
no longer use current_status in Torvald's current master.
I've not checked if free_BSD or others are using the current_status field.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The implementation previously ignored null strings (""), but
these could be important, especially for debug.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes a single-object memory leak on a store-to-reference method
invocation. ACPICA BZ 1439.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After being enabled for the first time, the GPEs may have STS bits already
set. Setting EN bits is not sufficient to trigger the GPEs again, so this
patch polls GPEs after enabling them for the first time.
This is a cleaner version on top of the "GPE clear" fix generated according
to Mika's report and Rafael's original Linux based fix. Based on Linux
commit originated from Rafael J. Wysocki, fixed by Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a risk that a GPE method/handler may be invoked twice. Let's
consider a case, both GPE0(RAW_HANDLER) and GPE1(_Exx) is triggered.
=======================================+=============================
IRQ handler (top-half) |IRQ polling
=======================================+=============================
acpi_ev_detect_gpe() |
LOCK() |
READ (GPE0-7 enable/status registers)|
^^^^^^^^^^^^ROOT CAUSE^^^^^^^^^^^^^^^|
Walk GPE0 |
UNLOCK() |LOCK()
Invoke GPE0 RAW_HANDLER |READ (GPE1 enable/status bit)
|acpi_ev_gpe_dispatch(irq=false)
| CLEAR (GPE1 enable bit)
| CLEAR (GPE1 status bit)
LOCK() |UNLOCK()
Walk GPE1 +=============================
acpi_ev_gpe_dispatch(irq=true) |IRQ polling (defer)
CLEAR (GPE1 enable bit) +=============================
CLEAR (GPE1 status bit) |acpi_ev_async_execute_gpe_method()
Walk others | Evaluate GPE1 _Exx
fi | acpi_ev_async_enable_gpe()
UNLOCK() | LOCK()
=======================================+ SET (GPE enable bit)
IRQ handler (bottom-half) | UNLOCK()
=======================================+
acpi_ev_async_execute_gpe_method() |
Evaluate GPE1 _Exx |
acpi_ev_async_enable_gpe() |
LOCK() |
SET (GPE1 enable bit) |
UNLOCK() |
=======================================+=============================
If acpi_ev_detect_gpe() is only invoked from the IRQ context, there won't be
more than one _Lxx/_Exx evaluations for one status bit flagging if the IRQ
handlers controlled by the underlying IRQ chip/driver (ex. APIC) are run in
serial. Note that, this is a known potential gap and we had an approach,
locking entire non-raw-handler processes in the top-half IRQ handler and
handling all raw-handlers out of the locked loop to be friendly to those
IRQ chip/driver. But the approach is too complicated while the issue is not
so real, thus ACPICA treated such issue (if any) as a parallelism/quality
issue of the underlying IRQ chip/driver to stop putting it on the radar.
Bug in link #1 is suspiciously reflecting the same cause, and if so, it can
also be fixed by this simpler approach.
But it will be no excuse an ACPICA problem now if ACPICA starts to poll
IRQs itself. In the changed scenario, _Exx will be evaluated from the task
context due to new ACPICA provided "polling after enabling GPEs" mechanism.
And the above figure uses edge-triggered GPEs demonstrating the possibility
of evaluating _Exx twice for one status bit flagging.
As a conclusion, there is now an increased chance of evaluating _Lxx/_Exx
more than once for one status bit flagging.
However this is still not a real problem if the _Lxx/_Exx checks the
underlying hardware IRQ reasoning and finally just changes the 2nd and the
follow-up evaluations into no-ops. Note that _Lxx should always be written
in this way as a level-trigger GPE could have it's status wrongly
duplicated by the underlying IRQ delivery mechanisms. But _Exx may have
very low quality BIOS by BIOS to trigger real issues. For example, trigger
duplicated button notifications.
To solve this issue, we need to stop reading a bunch of enable/status
register bits, but read only one GPE's enable/status bit. And GPE status
register's W1C nature ensures that acknowledging one GPE won't affect
another GPEs' status bits. Thus the hardware GPE architecture has already
provided us with the mechanism of implementing such parallelism.
So we can lock around one GPE handling process to achieve the parallelism:
1. If we can incorporate GPE enable bit check in detection and ensure the
atomicity of the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
2. In addtion for edge-triggered GPEs, if we can ensure the atomicity of
the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
CLEAR (status bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
By doing a cleanup in this way, we can remove duplicate GPE handling code
and ensure that all logics are collected in 1 function. And the function
will be safe for both IRQ interrupt and IRQ polling, and will be safe for
us to release and re-acquire acpi_gbl_gpe_lock at any time rather than raw
handler only during the top-half IRQ handler. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196703 [#1]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Unconditionally clearing ACPI IRQs during suspend/resume can lead to
unexpected IRQ losts. This patch fixes this issue by removing such IRQ
clearing code.
If this patch triggers regression, the regression should be in the GPE
handlers that cannot correctly determine some spurious triggered events as
no-ops. Please report any regression related to this commit to the ACPI
component on kernel bugzilla. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196249
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Eric Bakula-Davis <ericbakuladavis@gmail.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>