The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.
So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.
Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff76834
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.
The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.
This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit 43fff76834 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
with:
pm_request_resume();
Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.
This results in the following happening:
1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
as no one has been calling pm_runtime_mark_last_busy(), the device was
resumed during those 5 seconds, so all the pm_request_resume() calls
while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
be read by the host the IRQ line is *already* / still logically high
when we autosuspend and since we use an edge triggered IRQ, the IRQ
will never trigger, causing the device to get stuck in suspend
Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
syzbot/kasan detected a double free in sctp_sendmsg_to_asoc:
BUG: KASAN: use-after-free in sctp_association_free+0x7b7/0x930
net/sctp/associola.c:332
Read of size 8 at addr ffff8801d8006ae0 by task syzkaller914861/4202
CPU: 1 PID: 4202 Comm: syzkaller914861 Not tainted 4.16.0-rc4+ #258
Hardware name: Google Google Compute Engine/Google Compute Engine
01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x24d lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x23c/0x360 mm/kasan/report.c:412
__asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
sctp_association_free+0x7b7/0x930 net/sctp/associola.c:332
sctp_sendmsg+0xc67/0x1a80 net/sctp/socket.c:2075
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
sock_sendmsg_nosec net/socket.c:629 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:639
SYSC_sendto+0x361/0x5c0 net/socket.c:1748
SyS_sendto+0x40/0x50 net/socket.c:1716
do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x42/0xb7
This was introduced by commit:
f84af33 sctp: factor out sctp_sendmsg_to_asoc from sctp_sendmsg
As the newly refactored function moved the wait_for_sndbuf call to a
point after the association was connected, allowing for peeloff events
to occur, which in turn caused wait_for_sndbuf to return -EPIPE which
was not caught by the logic that determines if an association should be
freed or not.
Fix it the easy way by returning the ordering of
sctp_primitive_ASSOCIATE and sctp_wait_for_sndbuf to the old order, to
ensure that EPIPE will not happen.
Tested by myself using the syzbot reproducers with positive results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: davem@davemloft.net
CC: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+a4e4112c3aff00c8cfd8@syzkaller.appspotmail.com
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Aspeed specification, the reset and enable sequence
should be done when the clock is stopped. The specification doesn't
define behavior if the reset is done while the clock is enabled.
From testing on the AST2500, the LPC Controller has problems if the
clock is reset while enabled.
Therefore, check whether the clock is enabled or not before performing
the reset and enable sequence in the Aspeed clock driver.
Reported-by: Lei Yu <mine260309@gmail.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the Aspeed clocks are disabled by setting the relevant bit in
the "clock stop control" register to one, while others are disabled by
setting their bit to zero. The driver already uses a flag per gate to
identify this behavior, but doesn't apply it in the clock is_enabled
function.
Use the existing gate flag to correctly return whether or not a clock
is enabled in the aspeed_clk_is_enabled function.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 6671507f0f ("clk: aspeed: Handle inverse polarity of USB port 1 clock gate")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A series of small fixes in ASoC, HD-audio and core stuff:
- A UAF fix in ALSA PCM core
- Yet more hardening for ALSA sequencer
- A regression fix for the previous HD-audio power_save option change
- Various ASoC codec fixes (sgtl5000, rt5651, hdmi-codec, wm_adsp)
- Minor ASoC platform fixes (AMD ACP, sun4i)
-----BEGIN PGP SIGNATURE-----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=mCc/
-----END PGP SIGNATURE-----
Merge tag 'sound-4.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A series of small fixes in ASoC, HD-audio and core stuff:
- a UAF fix in ALSA PCM core
- yet more hardening for ALSA sequencer
- a regression fix for the previous HD-audio power_save option change
- various ASoC codec fixes (sgtl5000, rt5651, hdmi-codec, wm_adsp)
- minor ASoC platform fixes (AMD ACP, sun4i)"
* tag 'sound-4.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Revert power_save option default value
ALSA: pcm: Fix UAF in snd_pcm_oss_get_formats()
ALSA: seq: Clear client entry before deleting else at closing
ALSA: seq: Fix possible UAF in snd_seq_check_queue()
ASoC: amd: 16bit resolution support for i2s sp instance
ASoC: wm_adsp: For TLV controls only register TLV get/set
ASoC: sun4i-i2s: Fix RX slot number of SUN8I
ASoC: hdmi-codec: Fix module unloading caused kernel crash
ASoC: rt5651: Fix regcache sync errors on resume
ASoC: sgtl5000: Fix suspend/resume
MAINTAINERS: Add myself as sgtl5000 maintainer
ASoC: samsung: Add the DT binding files entry to MAINTAINERS
sgtl5000: change digital_mute policy
Instead of relying on the tiling attached to a buffer object, make sure
to set the proper tiling for linear buffers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pass the list of valid format modifiers to planes upon initialization
and implement the ->format_mod_supported() callback so that userspace
can query for the valid combinations of formats and modifiers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-03-14
This series contains updates to i40e and i40evf only.
Corentin Labbe cleans up the left over FCoE files in the i40e driver.
Gustavo A R Silva fixes a cut and paste error.
Paweł fixes a race condition when the VF driver is loaded on a host and
virsh is trying to attach it to the virtual machine and set a MAC
address. Resolve the issue by adding polling in i40e_ndo_set_vf_mac()
when the VF is in reset mode.
Jake cleans up i40e_vlan_rx_register() since this only used in a single
location, so just inline the contents of the function. Created a helper
function to proper update the per-filter statistics when we delete it.
Factored out the re-enabling ATR and SB rules. Fixed an issue when
re-enabling ATR after the last TCPv4 filter is removed and ntuple is
still active, we were not restoring the TCPv4 filter input set.
Filip modifies the permission check function to ensure that it knows how
many filters are being requested, which allows the check to ensure that
the total number of filters in a single request does not cause us to go
over the limit.
Mariusz fixed an issue where the wrong calculation of partition id was
being done on OCP PHY mezzanine cards, which in turn caused wake on LAN
to be disabled on certain ports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- 2 DM multipath fixes for a fix that was merged into 4.15-rc5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaqoz6AAoJEMUj8QotnQNaNtEH/37YSs5yBXSzbsvRQuVsht1G
C5qXrTB22JczSBNBfC+i0h5o9bXSm5brL/lOcP0qEokXnhEFgVK/nfcJmDRErUuJ
7TJhvYPptrFJ0hR7uMzqXxqp5ZDY+/mmzj69s0ZGZyhVacvO/CDW9CPUg7vgROp2
lEUohb3vi1ZaaHavbb/di4/m88+niJw5Yi/TBV24O7UxixQ3F1aeC5UENbfOt9re
5CauY3OcosS0Z+Kr8rmOzy2l/yBd2bYl8YGf4sJHWp4hmPec9PXUBOAK9wca9ouA
UNVh/2SBddjmM8wsDzUGsJJyZW+YN2eh2fzs9eJIDfrOFt4BhueUVUzKcxXo+RE=
=XErm
-----END PGP SIGNATURE-----
Merge tag 'for-4.16/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable DM multipath fix to restore ability to pass integrity data
- two DM multipath fixes for a fix that was merged into 4.16-rc5
* tag 'for-4.16/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: fix passing integrity data
dm mpath: eliminate need to use scsi_device_from_queue
dm mpath: fix uninitialized 'pg_init_wait' waitqueue_head NULL pointer
UEFI 2.7 defines in page 758 that:
Initial Label Storage Area Configuration
:
The minimum size of the Label Storage Area is large enough to
hold 2 index blocks and 2 labels.
The mininum index block size is 256 bytes, and the minimum label size
is also 256 bytes.
Change ND_LABEL_MIN_SIZE to (256 * 4) so that NVDIMM devices with
the minimum label storage area do not fail with the size check in
nvdimm_init_config_data().
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use xfs_iext_prev_extent to skip to the previous extent instead of
opencoding it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Simplify the control flow a bit in preparation for O_ATOMIC-related
changes.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This helper doesn't add any real value over just calling iomap_zero_range
directly, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Now that we convert COW preallocations from unwritten to real on every
call this function needs to be called with the ilock held exclusively.
Fortunately we already do that, but update the assert to match.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There is no reason to get a mapping bigger than what we were asked for.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
i_cnextents does not include delayed allocated extents, so switch
to the inode fork size check that we already use in other places
instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
->fail_addr and ->addr can be updated no matter the result of
parent->_erase(), we just need to remove the code doing the same thing
in mtd_erase_callback() to avoid adjusting those fields twice.
Note that this can be done because all MTD users have been converted to
not pass an erase_info->callback() and are thus only taking the
->addr_fail and ->addr fields into account after part_erase() has
returned.
While we're at it, get rid of the erase_info->mtd field which was only
needed to let mtd_erase_callback() get the partition device back.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Commit 3c47d19ff4 ("drivers: base: add coredump driver ops") added
a new callback in struct device_driver, but not a kerneldoc description
so here it is.
Fixes: 3c47d19ff4 ("drivers: base: add coredump driver ops")
Signed-off-by: Arend van Spriel <aspriel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of the mtd->_erase() implementations work in an asynchronous manner,
so let's simplify MTD users that call mtd_erase(). All they need to do
is check the value returned by mtd_erase() and assume that != 0 means
failure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
To date this driver has relied on prevous state from out of tree hacks
and vendor u-boot trees in order to have the host be able to access
data over the LPC bus.
Now we explicitly enable the AHB to LPC bridge and FWH cycles from when
the user first configures the address to map. We chose to do this then
as before that time there is no way for the kernel to know where it is
safe to point the LPC window.
Tested-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPC device needs to ensure it's clock is enabled before it can do
anything.
In the past the clock was enabled and left running by u-boot, however
Linux now has an upstream clock driver that disables unused clocks.
Tested-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPC Host Interface Controller is part of a BMC SoC that is used for
communication with the host.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ixjuser.h includes the telephony.h header. Other than that no kernel
code uses any of these headers. The last user of the ixjuser.h header
has been removed in commit 7326446c72 (Staging: remove telephony
drivers), more than 5 years ago.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for two MEN UARTs (16z025 and 16z057) to the
8250_men_mcb driver.
The 16z025 consists of up to four ports, the 16z057 has
exactly four ports. Apart from that, all of them share the
Port settings.
Signed-off-by: Michael Moese <mmoese@suse.de>
Reported-by: Ben Turner <ben.turner@21net.com>
Tested-by: Ben Turner <ben.turner@21net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(),
even if it returned an error! Always use put_device() to
give up the reference initialized.
Release allocated memory for vop device in vop_release_dev().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I tried to use devm_ioremap function and review related
code, I found devm_ioremap_* almost have the similar realize
with each other, which can be combined.
In the former version, I have tried to kill ioremap_cache to
reduce the size of devres, which can not work for ioremap is
not the same as ioremap_nocache in some ARCHs likes ia64.
Therefore, as the suggestion of Christophe, I introduce a help
function __devm_ioremap, let devm_ioremap* inline and call
__devm_ioremap with different devm_ioremap_type.
After apply the patch, the size of devres.o can be reduce from
8216 Bytes to 8052 Bytes in my compile environment.
Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Suggested-by: Christophe LEROY <christophe.leroy@c-s.fr>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Reviewed-by: Christophe LEROY <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Width 20 given in format string is larger than destination
buffer 'type[20]', use %19s to prevent overflowing it.
Fixes: bbecb07fa0 ("siox: new driver framework for eckelmann SIOX")
Cc: stable <stable@vger.kernel.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new crypto API use causes some problems with Kconfig dependencies,
including this link error:
fs/pstore/platform.o: In function `pstore_register':
platform.c:(.text+0x248): undefined reference to `crypto_has_alg'
platform.c:(.text+0x2a0): undefined reference to `crypto_alloc_base'
fs/pstore/platform.o: In function `pstore_unregister':
platform.c:(.text+0x498): undefined reference to `crypto_destroy_tfm'
crypto/lz4hc.o: In function `lz4hc_sdecompress':
lz4hc.c:(.text+0x1a): undefined reference to `LZ4_decompress_safe'
crypto/lz4hc.o: In function `lz4hc_decompress_crypto':
lz4hc.c:(.text+0x5a): undefined reference to `LZ4_decompress_safe'
crypto/lz4hc.o: In function `lz4hc_scompress':
lz4hc.c:(.text+0xaa): undefined reference to `LZ4_compress_HC'
crypto/lz4hc.o: In function `lz4hc_mod_init':
lz4hc.c:(.init.text+0xf): undefined reference to `crypto_register_alg'
lz4hc.c:(.init.text+0x1f): undefined reference to `crypto_register_scomp'
lz4hc.c:(.init.text+0x2f): undefined reference to `crypto_unregister_alg'
The problem is that with CONFIG_CRYPTO=m, we must not 'select CRYPTO_LZ4'
from a bool symbol, or call crypto API functions from a built-in
module.
This turns the sub-options into 'tristate' ones so the dependencies
are honored, and makes the pstore itself select the crypto core
if necessary.
Fixes: cb3bee0369 ("pstore: Use crypto compress API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
/dev/nvram was never meant to be used alongside the RTC CMOS driver from
drivers/rtc as it already expose the NVRAM through another interface..
Anyway, the last defconfig to enable it properly was removed in 2010 so
prevent ARM users from selecting it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions rts5260_get_ocpstat, rts5260_get_ocpstat2,
rts5260_clear_ocpstat, rts5260_process_ocp, rts5260_init_hw and
rts5260_set_aspm are local to the source and do not need to be
in global scope, so make them static.
Cleans up sparse warnings:
symbol 'rts5260_get_ocpstat' was not declared. Should it be static?
symbol 'rts5260_get_ocpstat2' was not declared. Should it be static?
symbol 'rts5260_clear_ocpstat' was not declared. Should it be static?
symbol 'rts5260_process_ocp' was not declared. Should it be static?
symbol 'rts5260_init_hw' was not declared. Should it be static?
symbol 'rts5260_set_aspm' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_blkdev() and __register_chrdev_region() treat the major
number as an unsigned int. So print it the same way to avoid
absurd error statements such as:
"... major requested (-1) is greater than the maximum (511) ..."
(and also fix off-by-one bugs in the error prints).
While at it, also update the comment describing register_blkdev().
Signed-off-by: Srivatsa S. Bhat <srivatsa@csail.mit.edu>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CHRDEV_MAJOR_DYN_END and CHRDEV_MAJOR_DYN_EXT_END are valid major
numbers. So fix the loop iteration to include them in the search for
free major numbers.
While at it, also remove a redundant if condition ("cd->major != i"),
as it will never be true.
Signed-off-by: Srivatsa S. Bhat <srivatsa@csail.mit.edu>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now the vblank event completion is racing with the atomic update,
which is especially bad when the PRE is in use, as one of the hardware
issue workaround might extend the atomic commit for quite some time.
If the vblank IRQ happens to trigger during that time, we will prematurely
signal the atomic commit completion to userspace, which causes tearing
when userspace re-uses a framebuffer we haven't managed to flip away from
yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ipu_planes_assign_pre() prototype is in "imx-drm.h" header file, so
include it to fix the following sparse warning:
drivers/gpu/drm/imx/ipuv3-plane.c:729:5: warning: symbol 'ipu_planes_assign_pre' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
ipu_plane_state_reset(), ipu_plane_duplicate_state() and
ipu_plane_destroy_state() are only used in this file, so make them static.
This fixes the following sparse warnings:
drivers/gpu/drm/imx/ipuv3-plane.c:275:6: warning: symbol 'ipu_plane_state_reset' was not declared. Should it be static?
drivers/gpu/drm/imx/ipuv3-plane.c:295:24: warning: symbol 'ipu_plane_duplicate_state' was not declared. Should it be static?
drivers/gpu/drm/imx/ipuv3-plane.c:309:6: warning: symbol 'ipu_plane_destroy_state' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
gcc-8 reports that we access an array with a negative index
in an error case:
drivers/gpu/ipu-v3/ipu-prg.c: In function 'ipu_prg_channel_disable':
drivers/gpu/ipu-v3/ipu-prg.c:252:43: error: array subscript -22 is below array bounds of 'struct ipu_prg_channel[3]' [-Werror=array-bounds]
This moves the range check in front of the first time that
variable gets used.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When CONFIG_ACPI is disabled, we never initialize the acpi_table
structure in kfd_create_crat_image_virtual:
drivers/gpu/drm/amd/amdkfd/kfd_crat.c: In function 'kfd_create_crat_image_virtual':
drivers/gpu/drm/amd/amdkfd/kfd_crat.c:888:40: error: 'acpi_table' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The undefined behavior also happens for any other acpi_get_table()
failure, but then the compiler can't warn about it.
This adds an error check that prevents the structure from
being used in error, avoiding both the undefined behavior and
the warning about it.
Fixes: 520b8fb755 ("drm/amdkfd: Add topology support for CPUs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Re-use the object-like macro EARLYCON_USED_OR_UNUSED to mark
`earlycon_acpi_spcr_enable` as maybe_unused.
Fix the following warning (treated as error in W=1)
CC arch/powerpc/kernel/setup-common.o
In file included from ./include/linux/serial_8250.h:14:0,
from arch/powerpc/kernel/setup-common.c:33:
./include/linux/serial_core.h:382:19: error: ‘earlycon_acpi_spcr_enable’ defined but not used [-Werror=unused-const-variable=]
static const bool earlycon_acpi_spcr_enable;
^~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some fields are not used by MTD drivers, users or core code. Moreover,
those fields are not documented, so get rid of them to avoid any
confusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
mtd_erase() can return an error before ->fail_addr is initialized to
MTD_FAIL_ADDR_UNKNOWN. Move this initialization at the very beginning
of the function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Use %*ph format to print small buffer as hex string.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Pointer bdev is being initialized however this value is never
read as bdev is assigned an updated value from the returned
call to blkdev_get_by_path. Remove the redundant assignment.
Cleans up clang warning:
drivers/mtd/devices/block2mtd.c:228:23: warning: Value stored to
'bdev' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>