If the cpuidle init cpu operation returns -ENXIO, therefore reporting HW
failure or misconfiguration, the CPUidle driver skips the respective
cpuidle device initialization because the associated platform back-end HW
is not operational.
That prevents the system to crash and allows to handle the error gracefully.
For example, on Qcom's platform, each core has a SPM. The device associated
with this SPM is initialized before the cpuidle framework. If there is an error
in the initialization (eg. error in the DT), the system continues to boot but
in degraded mode as some SPM may not be correctly initialized.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Eliminate extra indentation by putting all the code into the same block.
Also delete a bogus comment.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some hardware the USB fails to initialize to sane state after
cold boot. We can detect this based on some unexpected interrupt bits,
and recover by re-initializing.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fail and WARN if DMA counters are wrong.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move cvmx_usb_shutdown() to allow its use from some other functions.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't disable port before resetting. Also perform reset unconditionally
when requested.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move FIFO setup to controller reset from port reset.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move FIFO setup into a separate routine.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use USB stack to turn on the power bit. It will also do
the necessary delays.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't poll interrupts before we have registered the HCD.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move one-time state data structure initialization out of
cvmx_usb_initialize().
This enables to re-initialize USBN HW block without messing
up data structures.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Never retry after xacterr. The DMA engine cannot handle that properly
and may result in wrong transfer count and hang.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Program DMA engine based on transfer direction. We are only transferring
to one direction at a time.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __BITFIELD_FIELD to define bitfields. OCTEON can at least in theory
run also in little-endian mode, so the bitfield definitions should not
assume big-endian byte order.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are not moving/realigning the original pointer returned
by kmalloc, we don't need to store the value in a separate field.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Original CVMX code used "__" to distinguis internal USB functions
from public ones. But in Linux all cvmx_usb routines are internal
to this driver, so such separation is useless.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliminate 64-bit register access wrappers. Since we don't implement
register-level debugging outputs, these are useless.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove some function parameter sanity checks from internal functions
where we can rely them being called with sane parameters.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If power_supply_register() fails do not dereference returned ERR_PTR.
The pointer was dereferenced to print name of battery which registration
failed. Instead use the name from the power supply description passed to
the power_supply_register() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Do not call power_supply_powers() if power_supply_register() failed
earlier. This fixes possible NULL pointer dereference by
power_supply_powers() in such case.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Setting a dev_pm_ops resume callback but not a set of hibernation
handler means that pm function will not be called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the
suspend and hibernation handlers and move omap_dmm_resume under
CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
[tomi valkeinen: add missing 'static']
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting a dev_pm_ops suspend/resume pair but not a set of hibernation
functions means those pm functions will not be called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the
suspend and hibernation handlers and move
omap_drm_suspend/omap_drm_resume under CONFIG_PM_SLEEP to avoid build
warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
[tomi.valkeinen@ti.com: fix conflict, clean up description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We store the fb being page-flipped to 'old_fb' field, but we don't
increase the ref count of the fb when doing that. While I am not
sure if it can cause problem in practice, it's still safer to keep a ref
when storing a pointer to a fb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdrm DMM code sometimes crashes with:
WARNING: CPU: 0 PID: 1235 at lib/list_debug.c:36 __list_add+0x8c/0xbc()
list_add double add: new=e9265368, prev=e90139c4, next=e9265368.
This is caused by the code calling release_engine() twice for the same
engine.
dmm_txn_commit(wait=true) call is supposed to wait until the DMM
transaction has been finished. And it does that, but it does not wait
for the irq handler to finish.
What happens is that the irq handler is triggered, and it either wakes
up the thread that called dmm_txn_commit(), or that thread never even
slept because the transaction was finished in the HW very quickly. That
thread then continues executing, even if the irq handler is not yet
finished, and a new transaction may be initiated. If that transaction is
async (i.e. wait=false), a 'async' flag is set to true. The original irq
handler, which has yet not finished, then sees the transaction as
'async', even if it was supposed to be 'sync'.
When that happens, the irq handler does an extra release_engine() call
because it thinks it need to release the engine, leading to the crash.
This patch fixes the issue by using completion to ensure that the irq
handler has finished before a dmm_txn_commit(wait=true) may continue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_gem_objects are added to dev->obj_list in omap_gem_new, and removed
in omap_gem_free_object. Unfortunately there's no locking for
dev->obj_list, which eventually leads to a crash:
WARNING: CPU: 1 PID: 1123 at lib/list_debug.c:59 __list_del_entry+0xa4/0xe0()
list_del corruption. prev->next should be e9281344, but was ea722b84
Add a spinlock to protect dev->obj_list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
spin_is_locked(x) returns always 0 on uniprocessor, triggering BUG() in
omapdrm.
Change it to use assert_spin_locked() to fix the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need to ignore DIGIT SYNC LOST error when enabling/disabling TV
output. The code does that, but it ignores the DIGI SYNC LOST when
enabling any output. Normally this does no harm, but it could make us
miss DIGIT SYNC LOST on some rare occasions.
Fix the code to only ignore DIGIT SYNC LOST when enabling/disabling TV.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm tries to avoid error floods by unregistering the error irq when
an error happens, and then registering the error irq again later.
However, the code is racy, as it sometimes tries to unregister the error
irq when it's already unregistered, leading to WARN().
Also, the code only registers the error irq again when something is done
on that particular output, i.e. if only TV is used to flip the buffers,
and LCD is showing a same buffer, an error on LCD will cause the LCD
error irq to be unregistered and never registered again.
To fix this, let's keep the error irqs always enabled and trust the
DRM_ERROR_RATELIMITED to limit the flood.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm uses normal DRM_ERROR() print when the HW reports an error. As
we sometimes may get a flood of errors, let's rather use
DRM_ERROR_RATELIMITED().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When not using proper hotplug detection, DRM polls periodically the
connectors to find out if a cable is connected. This polling can happen
at any time, even very late in the suspend process.
This causes a problem with omapdrm, when the poll happens during the
suspend process after GPIOs have been disabled, leading to a crash in
gpio_get().
This patch fixes the issue by adding suspend and resume hooks to
omapdrm, in which we disable and enable, respectively, the polling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm has dummy functions for platform_device's
suspend/resume/shutdown. The functions don't do anything, and those
platform device functions are deprecated, so remove them from omapdrm.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The tiler irq handler uses engine->async value, but the code that sets
engine->async and enables the interrupt does not have a barrier. This
may cause the irq handler to see the old value of engine->async, causing
memory corruption.
Reported-by: Harinarayan Bhatta <harinarayan@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_plane_pre_apply() sets the plane's output channel too late, only
after the plane has already been otherwise configured and enabled. This
causes problems, as at the configuration stage we need to make decisions
based on the output channel.
This may lead to bad plane settings or failing to setup the plane.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP5 it is not possible to use TILER buffer with CPU when caching or
write-combining is used. Doing so leads to errors from the memory
manager.
However, on OMAP4, write-combining works fine.
This patch adds platform specific data for the TILER, and a function
tiler_get_cpu_cache_flags() which can be used to get the caching mode to
be used.
Note that without write-combining the use of the TILER buffer with CPU
is unusably slow. It's still good to have it operational for testing
purposes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm doesn't check if the pitch of the framebuffer and the color
format's bits-per-pixel are compatible. omapdss requires that the stride
of a buffer is an integer number of pixels
For example, when using modetest with a display that has x resolution of
1280, and using packed 24 RGB mode (3 bytes per pixel), modetest
allocates a buffer with a byte stride of 4 * 1280 = 5120. But 5120 / 3 =
1706.666... pixels, which causes wrong colors and a tilt on the screen.
Add a check into omapdrm to return an error if the user tries to use
such a combination.
Note: this is not a HW requirement at least for non-rotation use cases,
but a SW driver requirement. In the future we should study if also
rotation use cases are fine with any stride size, and if so, change the
driver to allow these strides.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When an error happens in omap_framebuffer_create(),
omap_framebuffer_create() calls omap_framebuffer_destroy() if the fb
struct has been allocated. However, that crashes, as
omap_framebuffer_destroy(), which calls drm_framebuffer_cleanup(),
should only be called after drm_framebuffer_init()
Fix this by just calling kfree() for the allocated fb when an error
happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdrm should work fine even if fbdev is missing. The current driver
crashes in that case, though, as it is missing checks for the fbdev.
Add the checks so that we don't free fbdev or restore fbdev mode when
there's no fbdev.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Even if the host controller doesn't have power during suspend, the card
is kept powered.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
unpin_worker() calls omap_framebuffer_unpin() without any locks, which
looks very suspicious. However, both pin and unpin are always called via
the driver's private workqueue, so the access is synchronized that way.
Add a comment to make this clear.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_framebuffer_pin() and omap_framebuffer_unpin() are currently
broken, as they cannot be called multiple times (i.e. pin, pin, unpin,
unpin), which is what happens in certain cases. This issue causes the
driver to possibly use 0 as an address for a displayed buffer, leading
to OCP error from DSS.
This patch fixes the issue by adding a simple pin_count, used to track
the number of pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clear omap_obj's paddr when unmapping the memory, so that it's easier to
catch bad use of the paddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM documentation says:
"If a page flip is already pending, the page_flip operation must return
-EBUSY."
Currently omapdrm returns -EINVAL instead. Fix omapdrm by returning
-EBUSY.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP DSS hardware supports changing the output port to which an overlay
manager's video stream goes. For example, DPI video stream can come from
any of the four overlay managers on OMAP5.
However, as it's difficult to manage the change in the driver, the
omapdss driver does not support that at the moment, and has a hardcoded
overlay manager per output.
omapdrm, on the other hand, uses the hardware features to find out which
overlay manager to use for an output, which causes problems. For
example, on OMAP5, omapdrm tries to use DIGIT overlay manager for DPI
output, instead of the LCD3 required by the omapdss driver.
This patch changes the omapdrm to use the omapdss driver's hardcoded
overlay managers, which fixes the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This fixes a bug in the new v8 Crypto Extensions GHASH code
that only manifests itself in big-endian mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename mce_severity() to mce_severity_intel() and assign the
mce_severity function pointer to mce_severity_amd() during init on AMD.
This way, we can avoid a test to call mce_severity_amd every time we get
into mce_severity(). And it's cleaner to do it this way.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Suggested-by: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1427125373-2918-3-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Add a severities function that caters to AMD processors. This allows us
to do some vendor-specific work within the function if necessary.
Also, introduce a vendor flag bitfield for vendor-specific settings. The
severities code uses this to define error scope based on the prescence
of the flags field.
This is based off of work by Boris Petkov.
Testing details:
Fam10h, Model 9h (Greyhound)
Fam15h: Models 0h-0fh (Orochi), 30h-3fh (Kaveri) and 60h-6fh (Carrizo),
Fam16h Model 00h-0fh (Kabini)
Boris:
Intel SNB
AMD K8 (JH-E0)
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: linux-edac@vger.kernel.org
Link: http://lkml.kernel.org/r/1427125373-2918-2-git-send-email-Aravind.Gopalakrishnan@amd.com
[ Fixup build, clean up comments. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Replace duplicated const keyword for 'sampleclock_sources' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
