[ Upstream commit e8bcf0ae4c ]
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 184fc2b9a8 ]
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e256ac5b1 ]
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86acc79071 ]
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be664cbefc ]
Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.
This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.
Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.
Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 227630cccd ]
This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:
1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.
This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.
2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.
This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52ca7d0f7b ]
The PCA9552 lines can be used either for driving LEDs or as GPIOs. The
manual states that for LEDs, the operation is open-drain:
The LSn LED select registers determine the source of the LED data.
00 = output is set LOW (LED on)
01 = output is set high-impedance (LED off; default)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
For GPIOs it suggests a pull-up so that the open-case drives the line
high:
For use as output, connect external pull-up resistor to the pin
and size it according to the DC recommended operating
characteristics. LED output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is
programmed LOW through the ‘LED selector’ register. The output
can be pulse-width controlled when PWM0 or PWM1 are used.
Now, I have a hardware design that uses the LED controller to control
LEDs. However, for $reasons, we're using the leds-gpio driver to drive
the them. The reasons are here are a tangent but lead to the discovery
of the inversion, which manifested as the LEDs being set to full
brightness at boot when we expected them to be off.
As we're driving the LEDs through leds-gpio, this means wending our way
through the gpiochip abstractions. So with that in mind we need to
describe an active-low GPIO configuration to drive the LEDs as though
they were GPIOs.
The set() gpiochip callback in leds-pca955x does the following:
...
if (val)
pca955x_led_set(&led->led_cdev, LED_FULL);
else
pca955x_led_set(&led->led_cdev, LED_OFF);
...
Where LED_FULL = 255. pca955x_led_set() in turn does:
...
switch (value) {
case LED_FULL:
ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_ON);
break;
...
Where PCA955X_LS_LED_ON is defined as:
#define PCA955X_LS_LED_ON 0x0 /* Output LOW */
So here we have some type confusion: We've crossed domains from GPIO
behaviour to LED behaviour without accounting for possible inversions
in the process.
Stepping back to leds-gpio for a moment, during probe() we call
create_gpio_led(), which eventually executes:
if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) {
state = gpiod_get_value_cansleep(led_dat->gpiod);
if (state < 0)
return state;
} else {
state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
}
...
ret = gpiod_direction_output(led_dat->gpiod, state);
In the devicetree the GPIO is annotated as active-low, and
gpiod_get_value_cansleep() handles this for us:
int gpiod_get_value_cansleep(const struct gpio_desc *desc)
{
int value;
might_sleep_if(extra_checks);
VALIDATE_DESC(desc);
value = _gpiod_get_raw_value(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
}
_gpiod_get_raw_value() in turn calls through the get() callback for the
gpiochip implementation, so returning to our get() implementation in
leds-pca955x we find we extract the raw value from hardware:
static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
{
struct pca955x *pca955x = gpiochip_get_data(gc);
struct pca955x_led *led = &pca955x->leds[offset];
u8 reg = pca955x_read_input(pca955x->client, led->led_num / 8);
return !!(reg & (1 << (led->led_num % 8)));
}
This behaviour is not symmetric with that of set(), where the val is
inverted by the driver.
Closing the loop on the GPIO_ACTIVE_LOW inversions,
gpiod_direction_output(), like gpiod_get_value_cansleep(), handles it
for us:
int gpiod_direction_output(struct gpio_desc *desc, int value)
{
VALIDATE_DESC(desc);
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
else
value = !!value;
return _gpiod_direction_output_raw(desc, value);
}
All-in-all, with a value of 'keep' for default-state property in a
leds-gpio child node, the current state of the hardware will in-fact be
inverted; precisely the opposite of what was intended.
Rework leds-pca955x so that we avoid the incorrect inversion and clarify
the semantics with respect to GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1d90147c9 ]
Since commit 4ad23a9764 ("MD: use per-cpu counter for writes_pending"),
the wait_queue is only got invoked if THREAD_WAKEUP is not set previously.
With above change, I can see process_metadata_update could always hang on
the wait queue, because mddev->thread could stay on 'D' status and the
THREAD_WAKEUP flag is not cleared since there are lots of place to wake up
mddev->thread. Then deadlock happened as follows:
linux175:~ # ps aux|grep md|grep D
root 20117 0.0 0.0 0 0 ? D 03:45 0:00 [md0_raid1]
root 20125 0.0 0.0 0 0 ? D 03:45 0:00 [md0_cluster_rec]
linux175:~ # cat /proc/20117/stack
[<ffffffffa0635604>] dlm_lock_sync+0x94/0xd0 [md_cluster]
[<ffffffffa0635674>] lock_token+0x34/0xd0 [md_cluster]
[<ffffffffa0635804>] metadata_update_start+0x64/0x110 [md_cluster]
[<ffffffffa04d985b>] md_update_sb.part.58+0x9b/0x860 [md_mod]
[<ffffffffa04da035>] md_update_sb+0x15/0x30 [md_mod]
[<ffffffffa04dc066>] md_check_recovery+0x266/0x490 [md_mod]
[<ffffffffa06450e2>] raid1d+0x42/0x810 [raid1]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
linux175:~ # cat /proc/20125/stack
[<ffffffffa0636679>] recv_daemon+0x3f9/0x5c0 [md_cluster]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
So let's revert the part of code in the commit to resovle the problem since
we can't get lots of benefits of previous change.
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4831ca9e4a ]
The allocation for elem may fail (especially because we're using
GFP_ATOMIC) so best to check for a null return. This fixes a potential
null pointer dereference when assigning elem->pool.
Detected by CoverityScan CID#1357507 ("Dereference null return value")
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcfd6b839c ]
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e72a060151 ]
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 784548c40d ]
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18eb86362a ]
Check memory allocation failures and return -ENOMEM in such cases, as
already done for other memory allocations in this function.
This avoids NULL pointers dereference.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: PJ Waskiewicz <peter.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 035ed07208 ]
On some i.MX6 platforms which do not have speed grading
check, opp table will not be created in platform code,
so cpufreq driver prints the following error message:
cpu cpu0: dev_pm_opp_get_opp_count: OPP table not found (-19)
However, this is not really an error in this case because the
imx6q-cpufreq driver first calls dev_pm_opp_get_opp_count()
and if it fails, it means that platform code does not provide
OPP and then dev_pm_opp_of_add_table() will be called.
In order to avoid such confusing error message, move it to
debug level.
It is up to the caller of dev_pm_opp_get_opp_count() to check its
return value and decide if it will print an error or not.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27d6162944 ]
When creating virtual functions, create the "virtfn%u" and "physfn" links
in sysfs *before* attaching the driver instead of after. When we attach
the driver to the new virtual network interface first, there is a race when
the driver attaches to the new sends out an "add" udev event, and the
network interface naming software (biosdevname or systemd, for example)
tries to look at these links.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ce9a36452 ]
Whenever an I/O for a RAID volume fails with IOCStatus
MPI2_IOCSTATUS_SCSI_IOC_TERMINATED and SCSIStatus equal to
(MPI2_SCSI_STATE_TERMINATED | MPI2_SCSI_STATE_NO_SCSI_STATUS) then
return the I/O to SCSI midlayer with "DID_RESET" (i.e. retry the IO
infinite times) set in the host byte.
Previously, the driver was completing the I/O with "DID_SOFT_ERROR"
which causes the I/O to be quickly retried. However, firmware needed
more time and hence I/Os were failing.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b3a081fb6 ]
In case of connection reset Tx skb queue can have some skbs which are
not transmitted so purge Tx skb queue in release_offload_resources() to
avoid skb leak.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 357027786f ]
When checking to see if a PCI bus can safely be reset, we previously
checked to see if any of the children had their PCI_DEV_FLAGS_NO_BUS_RESET
flag set. Children marked with that flag are known not to behave well
after a bus reset.
Some PCIe root port bridges also do not behave well after a bus reset,
sometimes causing the devices behind the bridge to become unusable.
Add a check for PCI_DEV_FLAGS_NO_BUS_RESET being set in the bridge device
to allow these bridges to be flagged, and prevent their secondary buses
from being reset.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fc7556877d ]
Change the return error code to EINVAL if the MAC
address is not valid in the set_wol function.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b64a2965d ]
On some platforms, the interrupt for the PL031 is optional. Avoid
trying to claim the interrupt if it's not specified.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 778f81d6cd ]
If crypto4xx is used in conjunction with dm-crypt, the available
ring buffer elements are not enough to handle the load properly.
On an aes-cbc-essiv:sha256 encrypted swap partition the read
performance is abyssal: (tested with hdparm -t)
/dev/mapper/swap_crypt:
Timing buffered disk reads: 14 MB in 3.68 seconds = 3.81 MB/sec
The patch increases both PPC4XX_NUM_SD and PPC4XX_NUM_PD to 256.
This improves the performance considerably:
/dev/mapper/swap_crypt:
Timing buffered disk reads: 104 MB in 3.03 seconds = 34.31 MB/sec
Furthermore, PPC4XX_LAST_SD, PPC4XX_LAST_GD and PPC4XX_LAST_PD
can be easily calculated from their respective PPC4XX_NUM_*
constant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d51fe3ba97 ]
The post-divider for the audio PLL is in bits [29:26], as specified
in the user manual, not [19:16] as currently programmed in the code.
The post-divider has a default register value of 2, i.e. a divider
of 3. This means the clock rate fed to the audio codec would be off.
This was discovered when porting sigma-delta modulation for the PLL
to sun5i, which needs the post-divider to be 1.
Fix the bit offset, so we do actually force the post-divider to a
certain value.
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4cdbc40d64 ]
The round_rate callback for N-M-factor style clocks does not check if
the requested clock rate is supported by the fractional clock mode.
While this doesn't affect usage in practice, since the clock rates
are also supported through N-M factors, it does not match the set_rate
code.
Add a check to the round_rate callback so it matches the set_rate
callback.
Fixes: 6174a1e24b ("clk: sunxi-ng: Add N-M-factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f687e25a7a ]
>From the CI builds, its been observed that during a driver
reload/insert, dp dual mode read function sometimes fails to
read from LSPCON device over i2c-over-aux channel.
This patch:
- adds some delay and few retries, allowing a scope for these
devices to settle down and respond.
- changes one error log's level from ERROR->DEBUG as we want
to call it an error only after all the retries are exhausted.
V2: Addressed review comments from Jani (for loop for retry)
V3: Addressed review comments from Imre (break on partial read too)
V3: Addressed review comments from Ville/Imre (Add the retries
exclusively for LSPCON, not for all dp_dual_mode devices)
V4: Added r-b from Imre, sending it to dri-devel (Jani)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102294
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102295
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102359
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103186
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507826408-19322-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d0c49aceb ]
This fixes an overflow condition that can happen with high max
brightness and period values in compute_duty_cycle. This fixes it by
using a 64 bit variable for computing the duty cycle.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f044113113 upstream.
The first node supplied to of_find_matching_node() has its reference
counter decreased as part of call to that function. In optee_driver_init()
after calling of_find_matching_node() it's invalid to call of_node_put() on
the supplied node again.
So remove the invalid call to of_node_put().
Reported-by: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Cc: <andi@linux-stable.l.notmuch.email>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3382290ed2 upstream.
[ Note, this is a Git cherry-pick of the following commit:
506458efaf ("locking/barriers: Convert users of lockless_dereference() to READ_ONCE()")
... for easier x86 PTI code testing and back-porting. ]
READ_ONCE() now has an implicit smp_read_barrier_depends() call, so it
can be used instead of lockless_dereference() without any change in
semantics.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508840570-22169-4-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1784f9144b upstream.
We'd like to use the 'PTI' acronym for 'Page Table Isolation' - free up the
namespace by renaming the <linux/pti.h> driver header to <linux/intel-pti.h>.
(Also standardize the header guard name while at it.)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f89fa286f upstream.
Replace ghes_io{re,un}map_pfn_{nmi,irq}()s use of ioremap_page_range()
with __set_fixmap() as ioremap_page_range() may sleep to allocate a new
level of page-table, even if its passed an existing final-address to
use in the mapping.
The GHES driver can only be enabled for architectures that select
HAVE_ACPI_APEI: Add fixmap entries to both x86 and arm64.
clear_fixmap() does the TLB invalidation in __set_fixmap() for arm64
and __set_pte_vaddr() for x86. In each case its the same as the
respective arch_apei_flush_tlb_one().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
[ For the arm64 bits: ]
Acked-by: Will Deacon <will.deacon@arm.com>
[ For the x86 bits: ]
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c49870e89f upstream.
For the SEA notification, the two functions ghes_sea_add() and
ghes_sea_remove() are only called when CONFIG_ACPI_APEI_SEA
is defined. If not, it will return errors in the ghes_probe()
and not continue. If the probe is failed, the ghes_sea_remove()
also has no chance to be called. Hence, remove the unnecessary
handling when CONFIG_ACPI_APEI_SEA is not defined.
For the NMI notification, it has the same issue as SEA notification,
so also remove the unused dead-code for it.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 095f613c6b upstream.
Match up with what 7edda0886b ("acpi: apei: handle SEA notification
type for ARMv8") did for ghes_ioremap_pfn_nmi().
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd3486ded7 upstream.
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 20665a9076 ]
Build errors have been reported with CONFIG_PM=n:
drivers/net/wireless/ath/ath10k/pci.c:3416:8: error: implicit
declaration of function 'ath10k_pci_suspend'
[-Werror=implicit-function-declaration]
drivers/net/wireless/ath/ath10k/pci.c:3428:8: error: implicit
declaration of function 'ath10k_pci_resume'
[-Werror=implicit-function-declaration]
These are caused by the combination of the following two commits:
6af1de2e4e ("ath10k: mark PM functions as __maybe_unused")
96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but
disabled")
Both build fine on their own.
But now that ath10k_pci_pm_{suspend,resume}() is compiled
unconditionally, we should also compile ath10k_pci_{suspend,resume}()
unconditionally.
And drop the #ifdef around ath10k_pci_hif_{suspend,resume}() too; they
are trivial (empty), so we're not saving much space by compiling them
out. And the alternatives would be to sprinkle more __maybe_unused, or
spread the #ifdef's further.
Build tested with the following combinations:
CONFIG_PM=y && CONFIG_PM_SLEEP=y
CONFIG_PM=y && CONFIG_PM_SLEEP=n
CONFIG_PM=n
Fixes: 96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but disabled")
Fixes: 096ad2a15fd8 ("Merge branch 'ath-next'")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 96378bd2c6 ]
For devices where the FW supports WoWLAN but user-space has not
configured it, we don't do any PCI-specific suspend/resume operations,
because mac80211 doesn't call drv_suspend() when !wowlan. This has
particularly bad effects for some platforms, because we don't stop the
power-save timer, and if this timer goes off after the PCI controller
has suspended the link, Bad Things will happen.
Commit 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
got some of this right, in that it understood there was a problem on
non-WoWLAN firmware. But it forgot the $subject case.
Fix this by moving all the PCI driver suspend/resume logic exclusively
into the driver PM hooks. This shouldn't affect WoWLAN support much
(this just gets executed later on).
I would just as well kill the entirety of ath10k_hif_suspend(), as it's
not even implemented on the USB or SDIO drivers. I expect that we don't
need the callback, except to return "supported" (i.e., 0) or "not
supported" (i.e., -EOPNOTSUPP).
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Fixes: 77258d409c ("ath10k: enable pci soc powersaving")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee0a47186e ]
When the user sets count to zero the string buffer would remain
completely uninitialized which causes the kernel to parse its
own stack data, potentially leading to an info leak. In addition
to that, the string might be not terminated properly when the
user data does not contain a 0-terminator.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e57903fd97 ]
It seems pblk_dealloc_page would race against pblk_alloc_pages for
line bitmap for sector allocation.The chances are very low but might
as well protect the bitmap properly.
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bd43241768 ]
pblk uses an internal page mempool for allocating pages on internal
bios. The main two users of this memory pool are partial reads (reads
with some sectors in cache and some on media) and padded writes, which
need to add dummy pages to an existing bio already containing valid
data (and with a large enough bioset allocated). In both cases, the
maximum number of pages per bio is defined by the maximum number of
physical sectors supported by the underlying device.
This patch fixes a bad mempool allocation, where the min_nr of elements
on the pool was fixed (to 16), which is lower than the maximum number
of sectors supported by NVMe (as of the time for this patch). Instead,
use the maximum number of allowed sectors reported by the device.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d327a9ed6 ]
The data buffer for the GC path allocates virtual memory through
vmalloc. When this change was introduced, a flag signaling kmalloc'ed
memory was wrongly introduced. Use the right flag when creating a bio
from this buffer.
Fixes: de54e703a4 ("lightnvm: pblk: use vmalloc for GC data buffer")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27b978725d ]
pblk_line_gc_list seems to had a bug since the introduction of pblk in
getting GC list for a line. In b20ba1bc7 while redesigning the GC
algorithm, the naming for the GC thresholds was altered, but the
values for high_thrs and mid_thrs were not. The result is that when
moving to the GC lists, the mid threshold is never evaluated.
Fixes: a4bd217b4("lightnvm: physical block device (pblk) target")
Signed-off-by: Rakesh Pandit <rakesh@tuxera.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e3a5b8ebd ]
GC can be kicked after it has been shut down when closing the last
line during exit, resulting in accesses to freed structures.
Make sure that GC is not triggered while it is not operational.
Also make sure that GC won't be re-activated during exit when
running on another processor by using timer_del_sync.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b4b678b06f ]
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0b64f58e8 ]
According to the C standard the behavior of computations with
integer operands is as follows:
* A computation involving unsigned operands can never overflow,
because a result that cannot be represented by the resulting
unsigned integer type is reduced modulo the number that is one
greater than the largest value that can be represented by the
resulting type.
* The behavior for signed integer underflow and overflow is
undefined.
Hence only use unsigned integers when checking for integer
overflow.
This patch is what I came up with after having analyzed the
following smatch warnings:
drivers/infiniband/core/cma.c:3448: cma_resolve_ib_udp() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
drivers/infiniband/core/cma.c:3505: cma_connect_ib() warn: signed overflow undefined. 'offset + conn_param->private_data_len < conn_param->private_data_len'
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dd6b9c2c33 ]
This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.
The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.
Fixes: 79cf79abce ("macvlan: add source mode")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 385f4d7f94 ]
The check used here is to avoid conflict between write and
resync, however we used the wrong logic, it should be the
inverse of the checking inside "if".
Fixes: 589a1c4 ("Suspend writes in RAID1 if within range")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07719ff767 ]
If starting an array that is undergoing rebuild, make ppl recovery honor
the recovery_offset of a member disk and don't read data that is not yet
in-sync.
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e35127565 ]
We could allocate less memory than intended because we do:
bfad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small. I fixed the network version of this in March with
commit 13e2d5187f ("bna: integer overflow bug in debugfs").
Fixes: ab2a9ba189 ("[SCSI] bfa: add debugfs support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 658e9a6dc1 ]
/sys/class/scsi_disk/0:2:0:0/allow_restart can be changed to 0
unexpectedly by writing an invalid string such as the following:
echo asdf > /sys/class/scsi_disk/0:2:0:0/allow_restart
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
