Commit graph

287,481 commits

Author SHA1 Message Date
Linus Torvalds
f9ed72dde3 Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
 "Two fixes in this pull request:

   - The writeback regression fix from Tejun, which has been weeks in
     the making.  This fixes a case where we would sometimes not issue
     writeback when we should have.

   - An older fix for a memory corruption issue in mtip32xx.  It was
     deferred since we wanted a better fix for this (driver should not
     have to handle that case), but given the timing, it's better to put
     the simple fix in for 4.2 release"

* 'for-linus' of git://git.kernel.dk/linux-block:
  mtip32x: fix regression introduced by blk-mq per-hctx flush
  writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
2015-08-26 11:08:47 -07:00
Stefan Brüns
63ab645f4d spi: check bits_per_word in spi_setup
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-08-26 18:58:29 +01:00
Sreekanth Reddy
5aeeb78aeb mpt2sas, mpt3sas: Abort initialization if no memory I/O resources detected
Driver crashes if the BIOS do not set up at least one
memory I/O resource. This failure can happen if the device is too
slow to respond during POST and is missed by the BIOS, but Linux
then detects the device later in the boot process.

Based on a patch from Timothy Pearson <tpearson@raptorengineeringinc.com>

Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:56:35 -07:00
Bart Van Assche
8d16366b5f qla2xxx: Avoid that sparse complains about context imbalances
Surround conditional locking statements with "#ifndef __CHECKER__" /
"#endif" to hide these for the sparse static source code analysis
tool.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:46:04 -07:00
Bart Van Assche
8a318fe160 qla2xxx: Remove dead code
The "return QLA_SUCCESS" statement just above the "fw_load_failed"
label cannot be reached, hence remove it. Additionally remove the
"else" keyword since the code block below the if-statement ends
with a return statement.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:45:02 -07:00
Bart Van Assche
82e6afd49d qla2xxx: Remove a superfluous test
Avoid that smatch reports the following warning:

drivers/scsi/qla2xxx/qla_attr.c:1081: qla2x00_model_desc_show() warn: this array is probably non-NULL. 'vha->hw->model_desc'

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:44:07 -07:00
Bart Van Assche
8dfa4b5a9b qla2xxx: Fix sparse annotations
This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:42:25 -07:00
Bart Van Assche
118e2ef9df qla2xxx: Avoid that sparse complains about duplicate [noderef] attributes
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:41:33 -07:00
Bart Van Assche
ad950360ee qla2xxx: Remove __constant_ prefix
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.

[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:40:32 -07:00
Bart Van Assche
df3f4cd0de qla2xxx: Replace two macros with an inline function
Replace the QLA82XX_ADDR_IN_RANGE() and QLA8044_ADDR_IN_RANGE() macros
with the inline function addr_in_range(). This avoids that the compiler
reports the following warning when building with W=1: comparison of
unsigned expression >= 0 is always true.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:35:35 -07:00
Bart Van Assche
52c82823cc qla2xxx: Remove set-but-not-used variables
Detected these variables by building with W=1.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:34:49 -07:00
Bart Van Assche
2374dd238c qla2xxx: Declare local functions static
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:34:20 -07:00
Bart Van Assche
c3ff356d08 qla2xxx: Report both rsp_info and rsp_info_len
Let the debug statement in qlafx00_tm_iocb_entry() report both rsp_info
and rsp_info_len instead of reporting rsp_info_len twice.

Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 10:33:40 -07:00
Dmitry Torokhov
e51e38494a Input: synaptics - fix handling of disabling gesture mode
Bit 2 of the mode byte has dual meaning: it can disable reporting of
gestures when touchpad works in Relative mode or normal Absolute mode,
or it can enable so called Extended W-Mode when touchpad uses enhanced
Absolute mode (W-mode). The extended W-Mode confuses our driver and
causes missing button presses on some Thinkpads (x250, T450s), so let's
make sure we do not enable it.

Also, according to the spec W mode "... bit is defined only in Absolute
mode on pads whose capExtended capability bit is set. In Relative mode and
in TouchPads without this capability, the bit is reserved and should be
left at 0.", so let's make sure we respect this requirement as well.

Reported-by: Nick Bowler <nbowler@draconx.ca>
Suggested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-08-26 10:09:22 -07:00
Dmitry Torokhov
3fffd12839 i2c: allow specifying separate wakeup interrupt in device tree
Instead of having each i2c driver individually parse device tree data in
case it or platform supports separate wakeup interrupt, and handle
enabling and disabling wakeup interrupts in their power management
routines, let's have i2c core do that for us.

Platforms wishing to specify separate wakeup interrupt for the device
should use named interrupt syntax in their DTSes:

	interrupt-parent = <&intc1>;
	interrupts = <5 0>, <6 0>;
	interrupt-names = "irq", "wakeup";

This patch is inspired by work done by Vignesh R <vigneshr@ti.com> for
pixcir_i2c_ts driver.

Note that the original code tried to preserve any existing wakeup
settings from userspace but was not quite right in that regard:
it would preserve wakeup flag set by userspace upon driver rebinding;
but it would re-arm the wakeup flag if it was disabled by userspace.

We think that resetting the flag upon re-binding the driver is proper
behavior as the driver is responsible for setting up and handling
wakeups.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Vignesh R <vigneshr@ti.com>
[wsa: updated the commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-26 18:47:58 +02:00
Dmitry Torokhov
6602c452ca of/irq: export of_get_irq_byname()
Similarly to of_get_irq(), let's export of_irq_get_byname(), so if a bus core
can be compiled as a module (such as I2C) it can have access to the symbol.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-26 18:47:57 +02:00
Guillermo A. Amaral
7a7184b01a Add factory recertified Crucial M500s to blacklist
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.

The new naming convention boils down to: s/Crucial_/FC/

Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
2015-08-26 11:30:47 -04:00
Hendrik Brueckner
1d3f9094c6 s390/sclp_vt220: support magic sysrequests
Implement magic sysrequest handling for the VT220 terminal (also known as
the Integrated ASCII console on the HMC/SE).
To invoke a "magic sysrequest" function, press "Ctrl+o" followed by a
second character that designates the debugging function.

The handling of the sysrq is scheduled away from the SCLP IRQ context;
because large amounts of sysrq output might fill up the console buffers.
The console might deadlock because it cannot empty the buffers while still
in the receiving IRQ context.  This behavior is the same as for the SCLP
console.

Reported-by: Horst Weber <hweber@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2015-08-26 17:20:45 +02:00
Hendrik Brueckner
ab7373bf23 s390/ctrlchar: improve handling of magic sysrequests
Extract the sysrq handling from the ctrlchar_handle() into a separate
function that can be directly used by other users.

Introduce a new sysrq_work structure to embed the work_struct and to
specify the magic sysrq function to be invoked.

Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2015-08-26 17:20:44 +02:00
Martin Schwidefsky
05bfd70bcd s390/3270: redraw screen on unsolicited device end
If a 3270 terminal is disconnected and later reconnected again,
it gets an unsolicited device end. This is currently ignored and
you have to hit the clear key to get the screen redrawn.
Add an automatic full redraw of the screen for this case.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2015-08-26 17:19:49 +02:00
Alok Pandey
e19b127f5b NVMe: Using PRACT bit to generate and verify PI by controller
This patch enables the PRCHK and reftag support when PRACT bit is set, and
block layer integrity is disabled.

Signed-off-by: Alok Pandey <pandey.alok@samsung.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-08-26 08:58:09 -06:00
Johannes Thumshirn
2d3a5d215e st: Destroy st_index_idr on module exit
Destroy st_index_idr on module exit, reclaiming the allocated memory.

This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@

module_init(init);

@ defines_module_exit @
identifier exit;
@@

module_exit(exit);

@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@

DEFINE_IDR(idr);

@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 idr_destroy(&idr);
 ...
}

@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@

exit(void)
{
 ...
 +idr_destroy(&idr);
}
</SmPL>

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:45:25 -07:00
Bjorn Helgaas
da0dc9fb4e megaraid_sas: fix whitespace errors
Fix whitespace and indentation errors.  No code change.

[jejb: checkpatch fixes]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:36:51 -07:00
Bjorn Helgaas
1be1825453 megaraid_sas: use dev_printk when possible
Use dev_printk() when possible to make messages more useful.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:33:39 -07:00
Bjorn Helgaas
3b8a1ba378 megaraid : use dev_printk when possible
Use dev_printk() when possible to make messages more useful.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:23:04 -07:00
Hannes Reinecke
14c3e677df scsi: Add ALUA state change UA handling
Log the ALUA state change unit attention correctly with
the message log and emit an event to allow user-space
tools to react to it.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:19:57 -07:00
Dan Carpenter
e819cdb198 mptfusion: prevent some memory corruption
These are signed values the come from the user, we put a cap on the
upper bounds but not on the lower bounds.

We use "karg.dataSgeOffset" to calculate "sz".  We verify "sz" and
proceed as if that means that "karg.dataSgeOffset" is correct but this
fails to consider that the "sz" calculations can have integer overflows.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
2015-08-26 07:11:45 -07:00
Markos Chandras
6f50c83529 IRQCHIP: irq-mips-gic: Add support for CM3 64-bit timer irqs
CM3 uses a 64-bit counter and compare registers so add support for
them in the GIC counter interrupt.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10648/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-08-26 15:23:17 +02:00
Markos Chandras
c3f57f02e3 IRQCHIP: irq-mips-gic: Extend GIC accessors for 64-bit CMs
Previously, the GIC accessors were only accessing u32 registers but
newer CMs may actually be 64-bit on MIPS64 cores. As a result of which,
extended these accessors to support 64-bit reads and writes.

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-08-26 15:23:17 +02:00
Maarten Lankhorst
c5b852f33e Partially revert "drm/i915: Use full atomic modeset."
This partially reverts commit 74c090b1bd.

The DRIVER_ATOMIC cap cannot yet be exported because i915 lacks async
support.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 15:14:52 +02:00
Paulo Zanoni
6c908bf43d drm/i915: gen 9 can check for unclaimed registers too
Dear git bisect user,

Even though this is the patch that introduced the WARN() you're
bisecting, please notice that it's very likely that the problem you're
facing was already present before this commit. In other words: this
commit adds code to detect errors and give WARN()s about them, but the
errors were already there.

In order to continue your debug, please use the i915.mmio_debug
option, check the backtraces and try to discover which read or write
operation is causing the error message. Then check if this is
happening because the register does not exist or because its power
well is down when the operation is being done.

On my SKL machine, if I use i915.mmio_debug=999, this patch triggers
42 WARNs just by booting. I didn't investigate them yet. Normal users
are only going to get a single WARN due to the default i915.mmio_debug
setting.

Thank you for your comprehension,
Paulo

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 15:14:02 +02:00
Julia Lawall
a0c81ce087 gpio: xlp: fix error return code
Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 14:49:23 +02:00
Stefan Agner
fd96811576 gpio: vf610: handle level IRQ's properly
The GPIO IRQ controller is able to generate level triggered
interrupts, however, these were handled by handle_simple_irq so far
which did not take care of IRQ masking. This lead to "nobody cared
(try booting with the "irqpoll" option)" stack traces.

Use the generic interrupt handlers depending on the IRQ type.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 14:45:11 +02:00
Maoguang Meng
58a5e1b64b pinctrl: mediatek: Implement wake handler and suspend resume
This patch implement irq_set_wake to get who is wakeup source and
setup on suspend resume.

Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 14:39:43 +02:00
Hongzhou Yang
d48c2c0264 pinctrl: mediatek: Fix multiple registration issue.
Since our common driver need support main chip and PMU
at the same time, that means it will register two
pinctrl device, and the pinctrl_desc structure should
be used two times.

But pinctrl_desc use global static definition, then
the latest registered pinctrl device will overwrite
the old one's, all members in pinctrl_desc will set to
the new one's, such as name, pins and pins numbers, etc.
This is a bug.

Move pinctrl_desc into mtk_pinctrl, assign new value for
each pinctrl device to fix it.

Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 14:37:44 +02:00
Ville Syrjälä
3e28878635 drm/i915: Force CL2 off in CHV x1 PHY
We can choose to leave the display PHY CL2 powerdown up to some hardware
signals, or we can force it. The BXT code forces the nonexistent CL2 in
the x1 PHY to power down. Follow suit on CHV. Maybe it can still save
some extra power by disabling some extra logic in CL1, or something.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:37:39 +02:00
Ville Syrjälä
ee27921824 drm/i915: Enable DPIO SUS clock gating on CHV
CHV has supports some form of automagic clock gating for the
DPIO SUS clock. We can simply enable the magic bits and the
hardware should take care of the rest.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:37:24 +02:00
Ville Syrjälä
0047eedc48 drm/i915: Force common lane on for the PPS kick on CHV
With DPIO powergating active the DPLL can't be accessed unless
something else is keeping the common lane in the channel on.
That means the PPS kick procedure could fail to enable the PLL.

Power up some data lanes to force the common lane to power up
so that the PLL can be enabled temporarily.

v2: Avoid gcc uninitilized variable warning

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:37:13 +02:00
Ville Syrjälä
b0b3384612 drm/i915: Trick CL2 into life on CHV when using pipe B with port B
Normmally the common lane in a PHY channel gets powered up when some
of the data lanes get powered up. But when we're driving port B with
pipe B we don't want to enabled any of the data lanes, and just want
the DPLL in the common lane to be active.

To make that happens we have to temporarily enable some data lanes
after which we can access the DPLL registers in the common lane. Once
the pipe is up and running we can drop the power override on the data
lanes allowing them to shut down. From this point forward the common
lane will in fact stay powered on until the data lanes in the other
channel get powered down.

Ville's extended explanation from the review thread:

On Wed, Aug 19, 2015 at 07:47:41AM +0530, Deepak wrote:
> One Q, why only for port B? Port C is also in same common lane right?

Port B is in the first PHY channel which also houses CL1. CL1 always
powers up whenever any lanes in either PHY channel are powered up.
CL2 only powers up if lanes in the second channel (ie. the one with
port C) powers up.

So in this scenario (pipe B->port B) we want the DPLL from CL2, but
ideally we only want to power up the lanes for port B. Powering up
port B lanes will only power up CL1, but as we need CL2 instead we
need to, temporarily, power up some lanes in port C as well.

Crossing the streams the other way (pipe A->port C) is not a problem
since CL1 powers up whenever anything else powers up. So powering up
some port C lanes is enough on its own to make the CL1 DPLL
operational, even though CL1 and the lanes live in separate channels.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
[danvet: Amend commit message with extended explanation.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:35:06 +02:00
Ville Syrjälä
e0fce78f04 drm/i915: Implement PHY lane power gating for CHV
Powergate the PHY lanes when they're not needed. For HDMI all four lanes
are needed always, but for DP we can enable only the needed lanes. To
power down the unused lanes we use some power down override bits in the
DISPLAY_PHY_CONTROL register. Without the overrides it appears that the
hardware always powers on all the lanes. When the port is disabled the
power down override is not needed and the lanes will shut off on their
own. That also means the override is critical to actually be able to
access the DPIO registers before the port is actually enabled.

Additionally the common lanes will power down when not needed. CL1
remains on as long as anything else is on, CL2 will shut down when
all the lanes in the same channel will shut down. There is one exception
for CL2 that will be dealt in a separate patch for clarity.

With potentially some lanes powered down, the DP code now has to check
the number of active lanes before accessing PCS/TX registers. All
registers in powered down blocks will reads as 0xffffffff, and soe we
would drown in warnings from vlv_dpio_read() if we allowed the code
to access all those registers.

Another important detail in the DP code is the "TX latency optimal"
setting. Normally the second TX lane acts as some kind of reset master,
with the other lanes as slaves. But when only a single lane is enabled,
that single lane obviously has to be the master.

A bit of extra care is needed to reconstruct the initial state of the
DISPLAY_PHY_CONTROL register since it can't be read safely. So instead
read the actual lane status from the DPLL/PHY_STATUS registers and
use that to determine which lanes ought to be powergated initially.

We also need to switch the PHY power modes to "deep PSR" to avoid
a hard system hang when powering down the single channel PHY.

Also sprinkle a few debug prints around so that we can monitor the
DISPLAY_PHY_STATUS changes without having to read it and risk
corrupting it.

v2: Add locking to chv_powergate_phy_lanes()
v3: Actually enable dynamic powerdown in the PHY and deal with the
    fallout

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:34:41 +02:00
Ville Syrjälä
5a8fbb7d19 drm/i915: Move DPLL ref/cri/VGA mode frobbing to the disp2d well enable
Bunch of stuff needs the DPLL ref/cri clocks on both VLV and CHV,
and having VGA mode enabled causes some problems for CHV. So let's just
pull the code to configure those bits into the disp2d well enable hook.
With the DPLL disable code also fixed to leave those bits alone we
should now have a consistent DPLL state all the time even if the DPLL
is disabled.

This also neatly removes some duplicated code between the VLV and
CHV codepaths.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 14:33:52 +02:00
Guilherme G. Piccoli
22b6839b91 PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().

The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.

To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.

Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2015-08-26 21:40:49 +10:00
Shinobu Uehara
580a7ee933 pinctrl: sh-pfc: r8a7794: add USB pin groups
Add USB0/1 pin groups to R8A7794 PFC driver.

Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
[Sergei: rebased, renamed, added changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 13:40:25 +02:00
Nicholas Krause
78de5d5220 gpio: max732x: Fix error handling in probe()
This fixes error handling in the function max732x_probe by checking
if the calls to the function max732x_readb fail by returning a error
code.

Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-26 13:34:55 +02:00
Kalle Valo
0ba3ac03c1 Merge ath-next from ath.git
Major changes in ath10k:

* add spectral scan support for qca99x0
* add qca6164 support
2015-08-26 12:40:23 +03:00
Raja Mani
ee92a2099f ath10k: fix compilation warnings in wmi phyerr pull function
Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.

wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
              but argument 4 has type 'long unsigned int' [-Wformat=]
              left_len, sizeof(*phyerr));
                        ^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
	      but argument 4 has type 'long unsigned int' [-Wformat=]
              left_len, sizeof(*phyerr));
                        ^
Fixes: 991adf71a6 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d7c ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-26 12:33:52 +03:00
Ville Syrjälä
4d9194dec3 drm/i915: Make some string arrays const
Most of our char* arrays are markes as const already, but a few slipped
through the cracks. Fix it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 11:19:36 +02:00
Ville Syrjälä
53abb6794a drm/i915: Use ARRAY_SIZE() instead of hand rolling it
A couple of hand rolled ARRAY_SIZE()s caught my eye. Get rid of them.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 11:19:30 +02:00
Ville Syrjälä
0a0b457fbf drm/i915: Fix some gcc warnings
Simple one:
drivers/gpu/drm/i915/i915_debugfs.c:2449:57: warning: Using plain integer as NULL pointer

And something a bit more peculiar:
drivers/gpu/drm/i915/i915_debugfs.c:4953:18: warning: Variable length array is used.
drivers/gpu/drm/i915/i915_debugfs.c:4953:32: warning: Variable length array is used.

We pass a 'const int' as the array size which results in the warning,
dropping the const gets rid of the warning. Weird, but I think getting
rid of the warnings is better than holding on to the const.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-08-26 11:19:22 +02:00
Michal Kazior
36582e5d4d ath10k: add qca6164 support
This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).

The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:

 ath10k_pci 0000:02:00.0: firmware register dump:
 ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
 ...

Note the value 0x000A012D.

Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-08-26 12:07:23 +03:00