commit 706136c572 upstream.
Add a final dma_wmb() barrier before triggering the transmit request
(TCCR_TSRQ) to ensure all descriptor and buffer writes are visible to
the DMA engine.
According to the hardware manual, a read-back operation is required
before writing to the doorbell register to guarantee completion of
previous writes. Instead of performing a dummy read, a dma_wmb() is
used to both enforce the same ordering semantics on the CPU side and
also to ensure completion of writes.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Cc: stable@vger.kernel.org
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251017151830.171062-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5370c31e84 upstream.
Ensure the TX descriptor type fields are published in a safe order so the
DMA engine never begins processing a descriptor chain before all descriptor
fields are fully initialised.
For multi-descriptor transmits the driver writes DT_FEND into the last
descriptor and DT_FSTART into the first. The DMA engine begins processing
when it observes DT_FSTART. Move the dma_wmb() barrier so it executes
immediately after DT_FEND and immediately before writing DT_FSTART
(and before DT_FSINGLE in the single-descriptor case). This guarantees
that all prior CPU writes to the descriptor memory are visible to the
device before DT_FSTART is seen.
This avoids a situation where compiler/CPU reordering could publish
DT_FSTART ahead of DT_FEND or other descriptor fields, allowing the DMA to
start on a partially initialised chain and causing corrupted transmissions
or TX timeouts. Such a failure was observed on RZ/G2L with an RT kernel as
transmit queue timeouts and device resets.
Fixes: 2f45d1902a ("ravb: minimize TX data copying")
Cc: stable@vger.kernel.org
Co-developed-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://patch.msgid.link/20251017151830.171062-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75cea9860a upstream.
TX frames aren't padded and unknown memory is sent into the ether.
Theoretically, it isn't even guaranteed that the extra memory exists
and can be sent out, which could cause further problems. In practice,
I found that plenty of tailroom exists in the skb itself (in my test
with ping at least) and skb_padto() easily succeeds, so use it here.
In the event of -ENOMEM drop the frame like other drivers do.
The use of one more padding byte instead of a USB zero-length packet
is retained to avoid regression. I have a dodgy Etron xHCI controller
which doesn't seem to support sending ZLPs at all.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251014203528.3f9783c4.michal.pecio@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f864458e9 upstream.
On all platforms set_clock_selection() writes to a GRF register. This
requires certain clocks running and thus should happen before the
clocks are disabled.
This has been noticed on RK3576 Sige5, which hangs during system suspend
when trying to suspend the second network interface. Note, that
suspending the first interface works, because the second device ensures
that the necessary clocks for the GRF are enabled.
Cc: stable@vger.kernel.org
Fixes: 2f2b60a0ec ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251014-rockchip-network-clock-fix-v1-1-c257b4afdf75@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0caeb24f5 upstream.
This patch fixes ce7a381697 ("net: bonding: add broadcast_neighbor option for 802.3ad").
Before this commit, on the broadcast mode, all devices were traversed using the
bond_for_each_slave_rcu. This patch supports traversing devices by using all_slaves.
Therefore, we need to update the slave array when enslave or release slave.
Fixes: ce7a381697 ("net: bonding: add broadcast_neighbor option for 802.3ad")
Cc: Simon Horman <horms@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: <stable@vger.kernel.org>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/all/a97e6e1e-81bc-4a79-8352-9e4794b0d2ca@kernel.org/
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251016125136.16568-1-tonghao@bamaicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e93ac51e4 upstream.
Since the commit c1f3f9797c ("can: netlink: can_changelink(): fix NULL
pointer deref of struct can_priv::do_set_mode"), the automatic restart
delay can only be set for devices that implement the restart handler struct
can_priv::do_set_mode. As it makes no sense to configure a automatic
restart for devices that doesn't support it.
However, since systemd commit 13ce5d4632e3 ("network/can: properly handle
CAN.RestartSec=0") [1], systemd-networkd correctly handles a restart delay
of "0" (i.e. the restart is disabled). Which means that a disabled restart
is always configured in the kernel.
On systems with both changes active this causes that CAN interfaces that
don't implement a restart handler cannot be brought up by systemd-networkd.
Solve this problem by allowing a delay of "0" to be configured, even if the
device does not implement a restart handler.
[1] 13ce5d4632
Cc: stable@vger.kernel.org
Cc: Andrei Lalaev <andrey.lalaev@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/all/20251020-certain-arrogant-vole-of-sunshine-141841-mkl@pengutronix.de
Fixes: c1f3f9797c ("can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode")
Link: https://patch.msgid.link/20251020-netlink-fix-restart-v1-1-3f53c7f8520b@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10843e1492 upstream.
If the send_peer_notif counter and the peer event notify are not synchronized.
It may cause problems such as the loss or dup of peer notify event.
Before this patch:
- If should_notify_peers is true and the lock for send_peer_notif-- fails, peer
event may be sent again in next mii_monitor loop, because should_notify_peers
is still true.
- If should_notify_peers is true and the lock for send_peer_notif-- succeeded,
but the lock for peer event fails, the peer event will be lost.
This patch locks the RTNL for send_peer_notif, events, and commit simultaneously.
Fixes: 07a4ddec3c ("bonding: add an option to specify a delay between peer notifications")
Cc: Jay Vosburgh <jv@jvosburgh.net>
Cc: Andrew Lunn <andrew+netdev@lunn.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Cc: Vincent Bernat <vincent@bernat.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tonghao Zhang <tonghao@bamaicloud.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251021050933.46412-1-tonghao@bamaicloud.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 399d109347 ]
Currently, during the LAN8814 PTP probe shared->phydev is only set if PTP
clock gets actually set, otherwise the function will return before setting
it.
This is an issue as shared->phydev is unconditionally being used when IRQ
is being handled, especially in lan8814_gpio_process_cap and since it was
not set it will cause a NULL pointer exception and crash the kernel.
So, simply always set shared->phydev to avoid the NULL pointer exception.
Fixes: b3f1a08fcf ("net: phy: micrel: Add support for PTP_PF_EXTTS for lan8814")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20251021132034.983936-1-robert.marko@sartura.hr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efd729408b ]
openvpn TCP encapsulation uses a custom queue to deliver packets to
userspace. Currently it relies on datagram_poll, which checks
sk_receive_queue, leading to false readiness signals when that queue
contains non-userspace packets.
Switch ovpn_tcp_poll to use datagram_poll_queue with the peer's
user_queue, ensuring poll only signals readiness when userspace data is
actually available. Also refactor ovpn_tcp_poll in order to enforce the
assumption we can make on the lifetime of ovpn_sock and peer.
Fixes: 11851cbd60 ("ovpn: implement TCP transport")
Signed-off-by: Antonio Quartulli <antonio@openvpn.net>
Signed-off-by: Ralf Lici <ralf@mandelbit.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://patch.msgid.link/20251021100942.195010-4-ralf@mandelbit.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d63f0391d6 ]
hibmcge uses fixed_phy_register() et al, but doesn't cater for the case
that hibmcge is built-in and fixed_phy is a module. To solve this
select FIXED_PHY.
Fixes: 1d7cd7a9c6 ("net: hibmcge: support scenario without PHY")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/c4fc061f-b6d5-418b-a0dc-6b238cdbedce@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d34f3dd8 ]
Resolve race conditions in timestamp events list handling between TX
and RX paths causing missed timestamps.
The current implementation uses a single events list for both TX and RX
timestamps. The am65_cpts_find_ts() function acquires the lock,
splices all events (TX as well as RX events) to a temporary list,
and releases the lock. This function performs matching of timestamps
for TX packets only. Before it acquires the lock again to put the
non-TX events back to the main events list, a concurrent RX
processing thread could acquire the lock (as observed in practice),
find an empty events list, and fail to attach timestamp to it,
even though a relevant event exists in the spliced list which is yet to
be restored to the main list.
Fix this by creating separate events lists to handle TX and RX
timestamps independently.
Fixes: c459f606f6 ("net: ethernet: ti: am65-cpts: Enable RX HW timestamp for PTP packets using CPTS FIFO")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://patch.msgid.link/20251016115755.1123646-1-a-garg7@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87bcef158a ]
XDP programs can change the layout of an xdp_buff through
bpf_xdp_adjust_tail() and bpf_xdp_adjust_head(). Therefore, the driver
cannot assume the size of the linear data area nor fragments. Fix the
bug in mlx5 by generating skb according to xdp_buff after XDP programs
run.
Currently, when handling multi-buf XDP, the mlx5 driver assumes the
layout of an xdp_buff to be unchanged. That is, the linear data area
continues to be empty and fragments remain the same. This may cause
the driver to generate erroneous skb or triggering a kernel
warning. When an XDP program added linear data through
bpf_xdp_adjust_head(), the linear data will be ignored as
mlx5e_build_linear_skb() builds an skb without linear data and then
pull data from fragments to fill the linear data area. When an XDP
program has shrunk the non-linear data through bpf_xdp_adjust_tail(),
the delta passed to __pskb_pull_tail() may exceed the actual nonlinear
data size and trigger the BUG_ON in it.
To fix the issue, first record the original number of fragments. If the
number of fragments changes after the XDP program runs, rewind the end
fragment pointer by the difference and recalculate the truesize. Then,
build the skb with the linear data area matching the xdp_buff. Finally,
only pull data in if there is non-linear data and fill the linear part
up to 256 bytes.
Fixes: f52ac7028b ("net/mlx5e: RX, Add XDP multi-buffer support in Striding RQ")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd5ba577c ]
XDP programs can release xdp_buff fragments when calling
bpf_xdp_adjust_tail(). The driver currently assumes the number of
fragments to be unchanged and may generate skb with wrong truesize or
containing invalid frags. Fix the bug by generating skb according to
xdp_buff after the XDP program runs.
Fixes: ea5d49bdae ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1760644540-899148-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffff5c8fc2 ]
When splitting the RTL8221B-VM-CG into C22 and C45 variants, the name was
accidentally changed to RTL8221B-VN-CG. This patch brings back the previous
part number.
Fixes: ad5ce743a6 ("net: phy: realtek: Add driver instances for rtl8221b via Clause 45")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016192325.2306757-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 902e81e679 ]
The blamed commit increased the needed headroom to account for
alignment. This means that the size required to always align a Tx buffer
was added inside the dpaa2_eth_needed_headroom() function. By doing
that, a manual adjustment of the pointer passed to PTR_ALIGN() was no
longer correct since the 'buffer_start' variable was already pointing
to the start of the skb's memory.
The behavior of the dpaa2-eth driver without this patch was to drop
frames on Tx even when the headroom was matching the 128 bytes
necessary. Fix this by removing the manual adjust of 'buffer_start' from
the PTR_MODE call.
Closes: https://lore.kernel.org/netdev/70f0dcd9-1906-4d13-82df-7bbbbe7194c6@app.fastmail.com/T/#u
Fixes: f422abe3f2 ("dpaa2-eth: increase the needed headroom to account for alignment")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251016135807.360978-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59bc32df2 ]
The ENETC RX ring uses the page halves flipping mechanism, each page is
split into two halves for the RX ring to use. And ENETC_RXB_TRUESIZE is
defined to 2048 to indicate the size of half a page. However, the page
size is configurable, for ARM64 platform, PAGE_SIZE is default to 4K,
but it could be configured to 16K or 64K.
When PAGE_SIZE is set to 16K or 64K, ENETC_RXB_TRUESIZE is not correct,
and the RX ring will always use the first half of the page. This is not
consistent with the description in the relevant kernel doc and commit
messages.
This issue is invisible in most cases, but if users want to increase
PAGE_SIZE to receive a Jumbo frame with a single buffer for some use
cases, it will not work as expected, because the buffer size of each
RX BD is fixed to 2048 bytes.
Based on the above two points, we expect to correct ENETC_RXB_TRUESIZE
to (PAGE_SIZE >> 1), as described in the comment.
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20251016080131.3127122-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50bd33f6b3 ]
After applying the workaround for err050089, the LS1028A platform
experiences RCU stalls on RT kernel. This issue is caused by the
recursive acquisition of the read lock enetc_mdio_lock. Here list some
of the call stacks identified under the enetc_poll path that may lead to
a deadlock:
enetc_poll
-> enetc_lock_mdio
-> enetc_clean_rx_ring OR napi_complete_done
-> napi_gro_receive
-> enetc_start_xmit
-> enetc_lock_mdio
-> enetc_map_tx_buffs
-> enetc_unlock_mdio
-> enetc_unlock_mdio
After enetc_poll acquires the read lock, a higher-priority writer attempts
to acquire the lock, causing preemption. The writer detects that a
read lock is already held and is scheduled out. However, readers under
enetc_poll cannot acquire the read lock again because a writer is already
waiting, leading to a thread hang.
Currently, the deadlock is avoided by adjusting enetc_lock_mdio to prevent
recursive lock acquisition.
Fixes: 6d36ecdbc4 ("net: enetc: take the MDIO lock only once per NAPI poll cycle")
Signed-off-by: Jianpeng Chang <jianpeng.chang.cn@windriver.com>
Acked-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20251015021427.180757-1-jianpeng.chang.cn@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf043a568 ]
When building with Clang 20 or newer, there are some objtool warnings
from unexpected fallthroughs to other functions:
vmlinux.o: warning: objtool: mlx5e_mpwrq_mtts_per_wqe() falls through to next function mlx5e_mpwrq_max_num_entries()
vmlinux.o: warning: objtool: mlx5e_mpwrq_max_log_rq_size() falls through to next function mlx5e_get_linear_rq_headroom()
LLVM 20 contains an (admittedly problematic [1]) optimization [2] to
convert divide by zero into the equivalent of __builtin_unreachable(),
which invokes undefined behavior and destroys code generation when it is
encountered in a control flow graph.
mlx5e_mpwrq_umr_entry_size() returns 0 in the default case of an
unrecognized mlx5e_mpwrq_umr_mode value. mlx5e_mpwrq_mtts_per_wqe(),
which is inlined into mlx5e_mpwrq_max_log_rq_size(), uses the result of
mlx5e_mpwrq_umr_entry_size() in a divide operation without checking for
zero, so LLVM is able to infer there will be a divide by zero in this
case and invokes undefined behavior. While there is some proposed work
to isolate this undefined behavior and avoid the destructive code
generation that results in these objtool warnings, code should still be
defensive against divide by zero.
As the WARN_ONCE() implies that an invalid value should be handled
gracefully, return 1 instead of 0 in the default case so that the
results of this division operation is always valid.
Fixes: 168723c1f8 ("net/mlx5e: xsk: Use umr_mode to calculate striding RQ parameters")
Link: https://lore.kernel.org/CAGG=3QUk8-Ak7YKnRziO4=0z=1C_7+4jF+6ZeDQ9yF+kuTOHOQ@mail.gmail.com/ [1]
Link: 37932643ab [2]
Closes: https://github.com/ClangBuiltLinux/linux/issues/2131
Closes: https://github.com/ClangBuiltLinux/linux/issues/2132
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251014-mlx5e-avoid-zero-div-from-mlx5e_mpwrq_umr_entry_size-v1-1-dc186b8819ef@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d93ff40d4 ]
dev->chipid is used in lan78xx_init_mac_address before it's initialized:
lan78xx_reset() {
lan78xx_init_mac_address()
lan78xx_read_eeprom()
lan78xx_read_raw_eeprom() <- dev->chipid is used here
dev->chipid = ... <- dev->chipid is initialized correctly here
}
Reorder initialization so that dev->chipid is set before calling
lan78xx_init_mac_address().
Fixes: a0db7d10b7 ("lan78xx: Add to handle mux control per chip id")
Signed-off-by: I Viswanath <viswanathiyyappan@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Khalid Aziz <khalid@kernel.org>
Link: https://patch.msgid.link/20251013181648.35153-1-viswanathiyyappan@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8fed52f7 ]
Bringing a linked netdevsim device down and then up causes communication
failure because both interfaces lack carrier. Basically a ifdown/ifup on
the interface make the link broken.
Commit 3762ec05a9 ("netdevsim: add NAPI support") added supported
for NAPI, calling netif_carrier_off() in nsim_stop(). This patch
re-enables the carrier symmetrically on nsim_open(), in case the device
is linked and the peer is up.
Signed-off-by: Breno Leitao <leitao@debian.org>
Fixes: 3762ec05a9 ("netdevsim: add NAPI support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251014-netdevsim_fix-v2-1-53b40590dae1@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c3f2e6281 ]
Some execution paths that jump to the fiber_setup_done label
could leave the remote_adv and local_adv variables uninitialized
and then use it.
Initialize this variables at the point of definition to avoid this.
Fixes: 85730a631f ("tg3: Add SGMII phy support for 5719/5718 serdes")
Co-developed-by: Alexandr Sapozhnikov <alsp705@gmail.com>
Signed-off-by: Alexandr Sapozhnikov <alsp705@gmail.com>
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://patch.msgid.link/20251014164736.5890-1-bigalex934@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5afca115 ]
Completion napi can free out-of-order tx descriptors if hw QoS is
enabled and packets with different priority are queued to same DMA ring.
Take into account possible out-of-order reports checking if the tx queue
is full using circular buffer head/tail pointer instead of the number of
queued packets.
Fixes: 23020f0493 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Suggested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251012-airoha-tx-busy-queue-v2-1-a600b08bab2d@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2616222e42 ]
During interface toggle operations (ifdown/ifup), the driver currently
resets the local helper variable 'phy_link' to -1. This causes the link
state machine to incorrectly interpret the state as a link change event,
resulting in spurious "Link is down" messages being logged when the
interface is brought back up.
Preserve the phy_link state across interface toggles to avoid treating
the -1 sentinel value as a legitimate link state transition.
Fixes: 88131a812b ("amd-xgbe: Perform phy connect/disconnect at dev open/stop")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Dawid Osuchowski <dawid.osuchowski@linux.intel.com>
Link: https://patch.msgid.link/20251010065142.1189310-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c67301584 ]
The driver is currently checking for PHYCR2 register presence in
rtl8211f_config_init(), but it does so after accessing PHYCR2 to
disable EEE. This was introduced in commit bfc17c1658 ("net:
phy: realtek: disable PHY-mode EEE"). Move the PHYCR2 presence
test before the EEE disablement and simplify the code.
Fixes: bfc17c1658 ("net: phy: realtek: disable PHY-mode EEE")
Signed-off-by: Marek Vasut <marek.vasut@mailbox.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251011110309.12664-1-marek.vasut@mailbox.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3f8c0a273 ]
When the driver requests Tx timestamp value, one of the first steps is
to clone SKB using skb_get. It increases the reference counter for that
SKB to prevent unexpected freeing by another component.
However, there may be a case where the index is requested, SKB is
assigned and never consumed by PTP flows - for example due to reset during
running PTP apps.
Add a check in release timestamping function to verify if the SKB
assigned to Tx timestamp latch was freed, and release remaining SKBs.
Fixes: 4901e83a94 ("idpf: add Tx timestamp capabilities negotiation")
Signed-off-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-1-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4d0c909bf ]
The Broadcom bcm54811 is hardware-strapped to select among RGMII and
GMII/MII/MII-Lite modes. However, the corresponding bit, RGMII Enable
in Miscellaneous Control Register must be also set to select desired
RGMII or MII(-lite)/GMII mode.
Fixes: 3117a11fff ("net: phy: bcm54811: PHY initialization")
Signed-off-by: Kamil Horák - 2N <kamilh@axis.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251009130656.1308237-2-kamilh@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70f92ab970 ]
After resume from S4 (hibernate), RTL8168H/RTL8111H truncates incoming
packets. Packet captures show messages like "IP truncated-ip - 146 bytes
missing!".
The issue is caused by RxConfig not being properly re-initialized after
resume. Re-initializing the RxConfig register before the chip
re-initialization sequence avoids the truncation and restores correct
packet reception.
This follows the same pattern as commit ef9da46dde ("r8169: fix data
corruption issue on RTL8402").
Fixes: 6e1d0b8988 ("r8169:add support for RTL8168H and RTL8107E")
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20251009122549.3955845-1-lilinmao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65946eac6d ]
There is no error handling for `dma_map_single()` failures.
Add error handling by checking `dma_mapping_error()` and freeing
the `skb` using `dev_kfree_skb()` (process context) when it fails.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Yeounsu Moon <yyyynoom@gmail.com>
Tested-on: D-Link DGE-550T Rev-A3
Suggested-by: Simon Horman <horms@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3abc0e55ea ]
Limit tx/rx buffer address to 32-bit address space for board with more
than 4GB DRAM.
Fixes: 804775dfc2 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Fixes: 6757d345dd ("net: ethernet: mtk_wed: introduce hw_rro support for MT7988")
Tested-by: Daniel Pawlik <pawlik.dan@gmail.com>
Tested-by: Matteo Croce <teknoraver@meta.com>
Signed-off-by: Rex Lu <rex.lu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9e30a22d6 ]
A suspend/resume cycle on a down interface results in the interface
coming up in Error Active state. A suspend/resume cycle on an Up
interface will always result in Error Active state, regardless of the
actual CAN state.
During suspend, only set running interfaces to CAN_STATE_SLEEPING.
During resume only touch the CAN state of running interfaces. For
wakeup sources, set the CAN state depending on the Protocol Status
Regitser (PSR), for non wakeup source interfaces m_can_start() will do
the same.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-4-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4942c42fe1 ]
In some SoCs (observed on the STM32MP15) the M_CAN IP core keeps the
CAN state and CAN error counters over an internal reset cycle. An
external reset is not always possible, due to the shared reset with
the other CAN core. This caused the core not always be in Error Active
state when bringing up the controller.
Instead of always setting the CAN state to Error Active in
m_can_chip_config(), fix this by reading and decoding the Protocol
Status Regitser (PSR) and set the CAN state accordingly.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-3-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d9db29b45 ]
The CAN Error State is determined by the receive and transmit error
counters. The CAN error counters decrease when reception/transmission
is successful, so that a status transition back to the Error Active
status is possible. This transition is not handled by
m_can_handle_state_errors().
Add the missing detection of the Error Active state to
m_can_handle_state_errors() and extend the handling of this state in
m_can_handle_state_change().
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Fixes: cd0d83eab2 ("can: m_can: m_can_handle_state_change(): fix state change")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-2-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba569fb07a ]
Commit 227619c3ff ("can: m_can: move runtime PM enable/disable to
m_can_platform") moved the PM runtime enable from the m_can core
driver into the m_can_platform.
That patch forgot to move the pm_runtime_disable() to
m_can_plat_remove(), so that unloading the m_can_platform driver
causes an "Unbalanced pm_runtime_enable!" error message.
Add the missing pm_runtime_disable() to m_can_plat_remove() to fix the
problem.
Cc: Patrik Flykt <patrik.flykt@linux.intel.com>
Fixes: 227619c3ff ("can: m_can: move runtime PM enable/disable to m_can_platform")
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://patch.msgid.link/20250929-m_can-fix-state-handling-v4-1-682b49b49d9a@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a27f6a8fb upstream.
This issue was found by Runcheng Lu when develop HSCanT USB to CAN FD
converter[1]. The original developers may have only 3 interfaces
device to test so they write 3 here and wait for future change.
During the HSCanT development, we actually used 4 interfaces, so the
limitation of 3 is not enough now. But just increase one is not
future-proofed. Since the channel index type in gs_host_frame is u8,
just make canch[] become a flexible array with a u8 index, so it
naturally constraint by U8_MAX and avoid statically allocate 256
pointer for every gs_usb device.
[1]: https://github.com/cherry-embedded/HSCanT-hardware
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Reported-by: Runcheng Lu <runcheng.lu@hpmicro.com>
Cc: stable@vger.kernel.org
Reviewed-by: Vincent Mailhol <mailhol@kernel.org>
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-max-if-v5-1-863330bf6666@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a12f0bc764 upstream.
The gs_usb driver supports USB devices with more than 1 CAN channel.
In old kernel before 3.15, it uses net_device->dev_id to distinguish
different channel in userspace, which was done in commit
acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id").
But since 3.15, the correct way is populating net_device->dev_port.
And according to documentation, if network device support multiple
interface, lack of net_device->dev_port SHALL be treated as a bug.
Fixes: acff76fa45 ("can: gs_usb: gs_make_candev(): set netdev->dev_id")
Cc: stable@vger.kernel.org
Signed-off-by: Celeste Liu <uwu@coelacanthus.name>
Link: https://patch.msgid.link/20250930-gs-usb-populate-net_device-dev_port-v1-1-68a065de6937@coelacanthus.name
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfdd74166a upstream.
The device returns a valid bit in the LSB of the low timestamp byte in
the completion descriptor that the driver should check before
setting the SKB's hardware timestamp. If the timestamp is not valid, do not
hardware timestamp the SKB.
Cc: stable@vger.kernel.org
Fixes: b2c7aeb490 ("gve: Implement ndo_hwtstamp_get/set for RX timestamping")
Reviewed-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Tim Hostetler <thostet@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251014004740.2775957-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5d790ba15 upstream.
The function lan78xx_write_raw_eeprom failed to properly propagate EEPROM
write timeout errors (-ETIMEDOUT). In the timeout fallthrough path, it first
attempted to restore the pin configuration for LED outputs and then
returned only the status of that restore operation, discarding the
original timeout error saved in ret.
As a result, callers could mistakenly treat EEPROM write operation as
successful even though the EEPROM write had actually timed out with no
or partial data write.
To fix this, handle errors in restoring the LED pin configuration separately.
If the restore succeeds, return any prior EEPROM write timeout error saved
in ret to the caller.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 8b1b2ca83b ("net: usb: lan78xx: Improve error handling in EEPROM and OTP operations")
cc: stable@vger.kernel.org
Signed-off-by: Bhanu Seshu Kumar Valluri <bhanuseshukumar@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75527d61d6 upstream.
rtl8152_driver_init() is missing the error handling.
When rtl8152_driver registration fails, rtl8152_cfgselector_driver
should be deregistered.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Cc: stable@vger.kernel.org
Signed-off-by: Yi Cong <yicong@kylinos.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251011082415.580740-1-yicongsrfy@163.com
[pabeni@redhat.com: clarified the commit message]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7075f501b upstream.
There was backward compatibility in the terms of mailbox API. Various
drivers from various OSes supporting 10G adapters from Intel portfolio
could easily negotiate mailbox API.
This convention has been broken since introducing API 1.4.
Commit 0062e7cc95 ("ixgbevf: add VF IPsec offload code") added support
for IPSec which is specific only for the kernel ixgbe driver. None of the
rest of the Intel 10G PF/VF drivers supports it. And actually lack of
support was not included in the IPSec implementation - there were no such
code paths. No possibility to negotiate support for the feature was
introduced along with introduction of the feature itself.
Commit 339f289641 ("ixgbevf: Add support for new mailbox communication
between PF and VF") increasing API version to 1.5 did the same - it
introduced code supported specifically by the PF ESX driver. It altered API
version for the VF driver in the same time not touching the version
defined for the PF ixgbe driver. It led to additional discrepancies,
as the code provided within API 1.6 cannot be supported for Linux ixgbe
driver as it causes crashes.
The issue was noticed some time ago and mitigated by Jake within the commit
d0725312ad ("ixgbevf: stop attempting IPSEC offload on Mailbox API 1.5").
As a result we have regression for IPsec support and after increasing API
to version 1.6 ixgbevf driver stopped to support ESX MBX.
To fix this mess add new mailbox op asking PF driver about supported
features. Basing on a response determine whether to set support for IPSec
and ESX-specific enhanced mailbox.
New mailbox op, for compatibility purposes, must be added within new API
revision, as API version of OOT PF & VF drivers is already increased to
1.6 and doesn't incorporate features negotiate op.
Features negotiation mechanism gives possibility to be extended with new
features when needed in the future.
Reported-by: Jacob Keller <jacob.e.keller@intel.com>
Closes: https://lore.kernel.org/intel-wired-lan/20241101-jk-ixgbevf-mailbox-v1-5-fixes-v1-0-f556dc9a66ed@intel.com/
Fixes: 0062e7cc95 ("ixgbevf: add VF IPsec offload code")
Fixes: 339f289641 ("ixgbevf: Add support for new mailbox communication between PF and VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-4-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53f0eb62b4 upstream.
E610 adapters no longer use the VFLINKS register to read PF's link
speed and linkup state. As a result VF driver cannot get actual link
state and it incorrectly reports 10G which is the default option.
It leads to a situation where even 1G adapters print 10G as actual
link speed. The same happens when PF driver set speed different than 10G.
Add new mailbox operation to let the VF driver request a PF driver
to provide actual link data. Update the mailbox api to v1.6.
Incorporate both ways of getting link status within the legacy
ixgbe_check_mac_link_vf() function.
Fixes: 4c44b450c6 ("ixgbevf: Add support for Intel(R) E610 device")
Co-developed-by: Andrzej Wilczynski <andrzejx.wilczynski@intel.com>
Signed-off-by: Andrzej Wilczynski <andrzejx.wilczynski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251009-jk-iwl-net-2025-10-01-v3-2-ef32a425b92a@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c24248ed78 upstream.
The value of skb_data->wait indicates whether skb is passed on to the
core mac80211 stack or released by the driver itself. Make sure that by
the time skb is added to txwd queue and becomes visible to the completing
side, it has already allocated and initialized TX wait related data (in
case it's needed).
This is found by code review and addresses a possible race scenario
described below:
Waiting thread Completing thread
rtw89_core_send_nullfunc()
rtw89_core_tx_write_link()
...
rtw89_pci_txwd_submit()
skb_data->wait = NULL
/* add skb to the queue */
skb_queue_tail(&txwd->queue, skb)
/* another thread (e.g. rtw89_ops_tx) performs TX kick off for the same queue */
rtw89_pci_napi_poll()
...
rtw89_pci_release_txwd_skb()
/* get skb from the queue */
skb_unlink(skb, &txwd->queue)
rtw89_pci_tx_status()
rtw89_core_tx_wait_complete()
/* use incorrect skb_data->wait */
rtw89_core_tx_kick_off_and_wait()
/* assign skb_data->wait but too late */
Found by Linux Verification Center (linuxtesting.org).
Fixes: 1ae5ca6152 ("wifi: rtw89: add function to wait for completion of TX skbs")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250919210852.823912-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
