[ Upstream commit ea3ce4cf07 ]
The unit addresses do not correspond to the nodes' reg properties,
because they don't have any.
Fixes: e42b650f82 ("ARM: dts: nuvoton: Add new device nodes to NPCM750 EVB")
Fixes: ee33e2fb3d ("ARM: dts: nuvoton: Add Quanta GBS BMC Device Tree")
Fixes: 59f5abe09f ("ARM: dts: nuvoton: Add Quanta GSJ BMC")
Fixes: 14579c76f5 ("ARM: dts: nuvoton: Add Fii Kudo system")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221031221553.163273-1-j.neuschaefer@gmx.net
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1150f4cff8 ]
The SEV kit reference design does not hook up the PCIe root port to the
core complex including it is misleading.
The entry is a re-use mistake - I was not aware of this when I moved
the PCIe node out of mpfs.dtsi so that individual bistreams could
connect it to different fics etc.
The node is disabled, so there should be no functional change here.
Fixes: 978a17d1a6 ("riscv: dts: microchip: add sevkit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8aa36c22d ]
The parent's input irq number is wrongly subtracted with 32 instead of
using the exact numbers in:
https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j721s2/interrupt_cfg.html
The GPIO interrupts are not working because of that. The toggling works
fine but interrupts are not firing. Fix the parent's input irq that
specifies the base for parent irq.
Tested for MAIN_GPIO0_6 interrupt on the j721s2 EVM.
Fixes: b8545f9d3a ("arm64: dts: ti: Add initial support for J721S2 SoC")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220922072950.9157-1-j-keerthy@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9f564c966 ]
dmc620_pmu_init() won't remove the callback added by
cpuhp_setup_state_multi() when platform_driver_register() failed. Remove
the callback by cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b3300 ("bus:
arm-ccn: Prevent hotplug callback leak")
Fixes: 53c218da22 ("driver/perf: Add PMU driver for the ARM DMC-620 memory controller")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
Link: https://lore.kernel.org/r/20221115115540.6245-2-shangxiaojing@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 973ae93d80 ]
tad_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b3300 ("bus:
arm-ccn: Prevent hotplug callback leak")
Fixes: 036a7584be ("drivers: perf: Add LLC-TAD perf counter support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221115070207.32634-3-yuancan@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit facafab761 ]
dsu_pmu_init() won't remove the callback added by cpuhp_setup_state_multi()
when platform_driver_register() failed. Remove the callback by
cpuhp_remove_multi_state() in fail path.
Similar to the handling of arm_ccn_init() in commit 26242b3300 ("bus:
arm-ccn: Prevent hotplug callback leak")
Fixes: 7520fa9924 ("perf: ARM DynamIQ Shared Unit PMU support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20221115070207.32634-2-yuancan@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb1fbffc6 ]
Alexander noted that KFENCE only expects to handle faults from invalid page
table entries (i.e. translation faults), but arm64's fault handling logic will
call kfence_handle_page_fault() for other types of faults, including alignment
faults caused by unaligned atomics. This has the unfortunate property of
causing those other faults to be reported as "KFENCE: use-after-free",
which is misleading and hinders debugging.
Fix this by only forwarding unhandled translation faults to the KFENCE
code, similar to what x86 does already.
Alexander has verified that this passes all the tests in the KFENCE test
suite and avoids bogus reports on misaligned atomics.
Link: https://lore.kernel.org/all/20221102081620.1465154-1-zhongbaisong@huawei.com/
Fixes: 840b239863 ("arm64, kfence: enable KFENCE for ARM64")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marco Elver <elver@google.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20221114104411.2853040-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69460e68eb ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes: 984aa6dbf4 ("OMAP3: PM: Adding smartreflex driver support.")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221108080322.52268-3-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e961c0f194 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes: 41f93af900 ("soc: ti: add Keystone Navigator QMSS driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221108080322.52268-2-zhangqilong3@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdd28ab35c ]
\#pwm-cells for the Icicle kit's fabric PWM was incorrectly set to 2 &
blindly overridden by the (out of tree) driver anyway. The core can
support inverted operation, so update the entry to correctly report its
capabilities.
Fixes: 72560c6559 ("riscv: dts: microchip: add fpga fabric section to icicle kit")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0336e2ce34 ]
Interrupt 12 of the Interrupt controller belongs to the SMI controller,
the right one for the display controller is the interrupt 13.
Fixes: 8113ba917d ("ARM: SPEAr: DT: Update device nodes")
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c800bcf07 ]
When the modem node was re-located to a separate LTE source file
"sc7280-herobrine-lte-sku.dtsi", some of the previous LTE users
weren't marked appropriately. Fix this by marking all Qualcomm
reference devices as LTE.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Fixes: d42fae738f ("arm64: dts: qcom: Add LTE SKUs for sc7280-villager family")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221110070813.1777-1-quic_sibis@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2927cf85f4 ]
To enable error reporting for a fabric to CCPLEX, we need to write its
register for enabling error interrupt to CCPLEX during boot and later
clear the error status register after error occurs. If a fabric's
registers are protected and not accessible from CCPLEX, then accessing
the registers will cause CBB firewall error.
Add support to check whether write access from CCPLEX to the registers
of a fabric is not blocked by it's firewall before enabling error
reporting to CCPLEX for that fabric.
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55084947d6 ]
Added checks to avoid potential out of bounds errors which can happen if
the 'slave map' and 'CBB errors' arrays are not correct or latest where
some entries are missing.
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd1d719b47 ]
Updating the slave map for fabrics and using the same maps for DCE, RCE
and SCE as they all are a replica in Tegra234.
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Stable-dep-of: 55084947d6 ("soc/tegra: cbb: Add checks for potential out of bound errors")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33af51a652 ]
In Tegra194 SoC, master_id bit range is different between cluster NOC
and CBB NOC. Currently same bit range is used which results in wrong
master_id value. Due to this, illegal accesses from the CCPLEX master
do not result in a crash as expected. Fix this by using the correct
range for the CBB NOC.
Finally, it is only necessary to extract the master_id when the
erd_mask_inband_err flag is set because when this is not set, a crash
is always triggered.
Fixes: b713442214 ("soc/tegra: cbb: Add CBB 1.0 driver for Tegra194")
Fixes: fc2f151d23 ("soc/tegra: cbb: Add driver for Tegra234 CBB 2.0")
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07ce611c70 ]
Binding requires node name to be rng not trng:
trng@1020f000: $nodename:0: 'trng@1020f000' does not match '^rng@[0-9a-f]+$'
Fixes: 50137c150f ("arm64: dts: mediatek: add basic mt7986 support")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221027151022.5541-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fbf94fea0 ]
The device_node pointer returned by of_find_matching_node() with
refcount incremented, when finish using it, the refcount need be
decreased.
Fixes: a967a289f1 ("RISC-V: sifive_l2_cache: Add L2 cache controller driver for SiFive SoCs")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a62d196e89 ]
corePWM is capable of inverted operation but the binding requires
\#pwm-cells of 2. Expand the binding to support setting the polarity.
Fixes: df77f77357 ("dt-bindings: pwm: add microchip corepwm binding")
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ac909916b ]
The preferred form for Renesas' compatible strings is:
"<vendor>,<family>-<module>"
Somehow the compatible string for the r9a09g011 I2C IP was upstreamed
as renesas,i2c-r9a09g011 instead of renesas,r9a09g011-i2c, which
is really confusing, especially considering the generic fallback
is renesas,rzv2m-i2c.
The first user of renesas,i2c-r9a09g011 in the kernel is not yet in
a kernel release, it will be in v6.1, therefore it can still be
fixed in v6.1.
Even if we don't fix it before v6.2, I don't think there is any
harm in making such a change.
s/renesas,i2c-r9a09g011/renesas,r9a09g011-i2c/g for consistency.
Fixes: 54ac6794df ("arm64: dts: renesas: r9a09g011: Add i2c nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221107165027.54150-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 278f5015a3 ]
Although the HW User Manual for RZ/V2M states in the "Address Map"
section that the interrupt controller is assigned addresses starting
from 0x82000000, the memory locations from 0x82000000 0x0x8200FFFF
are marked as reserved in the "Interrupt Controller (GIC)" section
and are currently not used by the device tree, leading to the below
warning:
arch/arm64/boot/dts/renesas/r9a09g011.dtsi:51.38-63.5: Warning
(simple_bus_reg): /soc/interrupt-controller@82000000: simple-bus unit
address format error, expected "82010000"
Fix the unit address accordingly.
Fixes: fb1929b98f ("arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20221103230648.53748-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64416ef0b0 ]
As serial communication requires a clean clock signal, the Serial
Communication Interfaces with FIFO (SCIF) are clocked by a clock that is
not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the SCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: c62331e822 ("arm64: dts: renesas: Add Renesas R8A779F0 SoC support")
Fixes: 4075314425 ("arm64: dts: renesas: r8a779f0: Add SCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5101ef18b ]
As serial communication requires a clean clock signal, the High Speed
Serial Communication Interfaces with FIFO (HSCIF) are clocked by a clock
that is not affected by Spread Spectrum or Fractional Multiplication.
Hence change the clock input for the HSCIF Baud Rate Generator internal
clock from the S0D3_PER clock to the SASYNCPERD1 clock (which has the
same clock rate), cfr. R-Car S4-8 Hardware User's Manual rev. 0.81.
Fixes: 01a787f78b ("arm64: dts: renesas: r8a779f0: Add HSCIF nodes")
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221103143440.46449-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3de1172624 ]
SM6125 comes with SDCC (SDHCI controller) v5, so the second range of
registers is cqhci, not core.
Fixes: cff4bbaf2a ("arm64: dts: qcom: Add support for SM6125")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # Sony Xperia 10 II
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026163646.37433-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d7860f575 ]
As idr_alloc() and of_property_read_string_index() can return negative
numbers, it should be better to check the return value and deal with
the exception.
Therefore, it should be better to use goto statement to stop and return
error.
Fixes: 6adba21eb4 ("soc: qcom: Add APR bus driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107014403.3606-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95fade4016 ]
The QMP pipe clock is used by the USB part of the PHY so drop the
corresponding properties from the DP child node.
Fixes: 23737b9557 ("arm64: dts: qcom: sm6350: Add USB1 nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026152511.9661-3-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb9f23e46d ]
The QMP pipe clock is used by the USB part of the PHY so drop the
corresponding properties from the DP child node.
Fixes: 5aa0d1becd ("arm64: dts: qcom: sm8250: switch usb1 qmp phy to USB3+DP mode")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221026152511.9661-2-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8f298d4f6 ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: f8b4eb64f2 ("arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0/2.0 and IDP boards")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-5-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1caf66104c ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: 0a3a56a93f ("arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-4-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15d9fcbb3e ]
The driver for the codec, when resetting the chip, first drives the line
low, and then high. This means that the line is active low. Change the
annotation in the DTS accordingly.
Fixes: 36c9d012f1 ("arm64: dts: qcom: use GPIO flags for tlmm")
Fixes: 5a263cf629 ("arm64: dts: qcom: sm8250-mtp: Add wcd9380 audio codec node")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-3-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76d21ffc5d ]
When resetting the block, the reset line is being driven low and then
high, which means that the line in DTS should be annotated as "active
low". It will become important when wcd9335 driver will be converted
to gpiod API that respects declared line polarities.
Fixes: f3eb39a55a ("arm64: dts: db820c: Add sound card support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221027074652.1044235-1-dmitry.torokhov@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7af949211a ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 07fa917a33 ("arm64: dts: qcom: sm8450: add ufs nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-5-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3c7839b69 ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 59c7cf8147 ("arm64: dts: qcom: sm8350: Add UFS nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-4-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f8b37dd4e ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: b7e2fba066 ("arm64: dts: qcom: sm8250: Add UFS controller and PHY")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-3-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 36a31b3a8d ]
The sizes of the UFS PHY register regions are too small and does
specifically not cover all registers used by the Linux driver.
As Linux maps these regions as full pages this is currently not an issue
on Linux, but let's update the sizes to match the vendor driver.
Fixes: 3834a2e922 ("arm64: dts: qcom: sm8150: Add ufs nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024091507.20342-2-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c882c899ea ]
The function platform_get_irq prints an error message into the kernel
log when the irq isn't found.
Since the interrupt is actually optional and not provided by some SoCs,
use platform_get_irq_optional which does not print an error message.
Fixes: c081f3060f ("soc: qcom: Add support to register LLCC EDAC driver")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104153041.412020-1-luca.weiss@fairphone.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59e787935c ]
The Trogdor Homestar DTSI adds additional GPIO52 pin to secondary I2S pins
("sec_mi2s_active") and configures it to "mi2s_1" function.
The Trogdor DTSI (which is included by Homestar) configures drive
strength and bias for all "sec_mi2s_active" pins, thus the intention was
to apply this configuration also to GPIO52 on Homestar.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: be0416a3f9 ("arm64: dts: qcom: Add sc7180-trogdor-homestar")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020225135.31750-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6105a8b7c ]
Evidently I forgot to update the unit address for the 38-bit cached
memory node when I changed the address in the reg property..
Update it to match.
Fixes: 6c11933017 ("riscv: dts: microchip: update memory configuration for v2022.10")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b13b2c3e0e ]
Commit b9e8a7d950 ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950 ("firmware: ti_sci: Switch transport to polled mode during system suspend")
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adf85adc2a ]
There is a sparse warning shown below:
drivers/soc/ti/knav_qmss_queue.c:70:12: warning: symbol
'knav_acc_firmwares' was not declared. Should it be static?
Since 'knav_acc_firmwares' is only called within knav_qmss_queue.c,
mark it as static to fix the warning.
Fixes: 96ee19becc ("soc: ti: add firmware file name as part of the driver")
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221019153212.72350-1-chenjiahao16@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5d577e3d5 ]
The WLAN regulator uses 'gpios' property instead of 'gpio' to specify
regulator enable GPIO. While the former is also currently handled by
the Linux kernel regulator-fixed driver, the later is the correct one
per DT bindings. Update the DT to use the later.
Fixes: 7dd5cbba42 ("ARM: dts: stm32: Enable WiFi on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
