Before re-starting link training reset the link phy params namely
the pre-emphasis and voltage swing levels otherwise the next
link training begins at the previously cached levels which can result
in link training failures.
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/605946/
Link: https://lore.kernel.org/r/20240725220450.131245-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
For cases where the crtc's connectors_changed was set without enable/active
getting toggled , there is an atomic_enable() call followed by an
atomic_disable() but without an atomic_mode_set().
This results in a NULL ptr access for the dpu_encoder_get_drm_fmt() call in
the atomic_enable() as the dpu_encoder's connector was cleared in the
atomic_disable() but not re-assigned as there was no atomic_mode_set() call.
Fix the NULL ptr access by moving the assignment for atomic_enable() and also
use drm_atomic_get_new_connector_for_encoder() to get the connector from
the atomic_state.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/59
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Patchwork: https://patchwork.freedesktop.org/patch/606729/
Link: https://lore.kernel.org/r/20240731191723.3050932-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Fix the dp_panel_get_supported_bpp() API to return the minimum
supported bpp correctly for relevant cases and use this API
to correct the behavior of DP driver which hard-codes the max supported
bpp to 30.
This is incorrect because the number of lanes and max data rate
supported by the lanes need to be taken into account.
Replace the hardcoded limit with the appropriate math which accounts
for the accurate number of lanes and max data rate.
changes in v2:
- Fix the dp_panel_get_supported_bpp() and use it
- Drop the max_t usage as dp_panel_get_supported_bpp() already
returns the min_bpp correctly now
changes in v3:
- replace min_t with just min as all params are u32
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/43
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/607073/
Link: https://lore.kernel.org/r/20240805202009.1120981-1-quic_abhinavk@quicinc.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
DPU debugging macros need to be converted to a proper drm_debug_*
macros, however this is a going an intrusive patch, not suitable for a
fix. Wire DPU_DEBUG and DPU_DEBUG_DRIVER to always use DRM_DEBUG_DRIVER
to make sure that DPU debugging messages always end up in the drm debug
messages and are controlled via the usual drm.debug mask.
I don't think that it is a good idea for a generic DPU_DEBUG macro to be
tied to DRM_UT_KMS. It is used to report a debug message from driver, so by
default it should go to the DRM_UT_DRIVER channel. While refactoring
debug macros later on we might end up with particular messages going to
ATOMIC or KMS, but DRIVER should be the default.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/606932/
Link: https://lore.kernel.org/r/20240802-dpu-fix-wb-v2-2-7eac9eb8e895@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Add the DSI host found on SM7150.
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601231/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This GPU is found on SoCs such as MSM8937 (450 MHz), MSM8940 (475 MHz),
SDM439 (650 MHz).
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/601411/
Signed-off-by: Rob Clark <robdclark@chromium.org>
On QCM2290 chipset DPU does not support UBWC.
Add a dpu cap to indicate this and do not expose compressed formats
in this case.
changes since RFC:
- use ubwc enc and dec version of mdss_data instead of catalog
to decide if ubwc is supported
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601392/
Signed-off-by: Rob Clark <robdclark@chromium.org>
To simplify, introduce the new gmu_chipid for a740 & a750 GPUs.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601396/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add support in drm/msm driver for the Adreno X185 gpu found in
Snapdragon X1 Elite chipset.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601399/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Document Adreno X185 GMU in the dt-binding specification.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/601395/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Disable the call to qcom_scm_gpu_init_regs() for a730 and a740
after init failures on the HDK8550 and HDK8450 platforms:
msm_dpu ae01000.display-controller: failed to load adreno gpu
msm_dpu ae01000.display-controller: failed to bind 3d00000.gpu (ops a3xx_ops [msm]): -5
msm_dpu ae01000.display-controller: adev bind failed: -5
While debugging, it happens the call to:
qcom_scm_gpu_init_regs(QCOM_SCM_GPU_ALWAYS_EN_REQ)
returns -5 and makes the gpu fail to initialize.
Remove the scm call since it's not done downstream either and
works fine without.
Fixes: 14b27d5df3 ("drm/msm/a7xx: Initialize a750 "software fuse"")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600972/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The gpulist has twice the a6xx gpulist, replace the second one
with the a7xx gpulist.
Solves:
msm_dpu ae01000.display-controller: Unknown GPU revision: 7.3.0.1
msm_dpu ae01000.display-controller: Unknown GPU revision: 67.5.10.1
msm_dpu ae01000.display-controller: Unknown GPU revision: 67.5.20.1
on SM8450, SM8550 & SM8560.
Fixes: 8ed322f632 ("drm/msm/adreno: Split up giant device table")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600939/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Commit f6ebff4fe810 ("drm/msm/adreno: De-spaghettify the use of memory
barriers") made some fixups relating to write arrival, ensuring that
the GPU's memory interface has *really really really* been told to come
out of reset. That in turn rendered the hacky commit being reverted no
longer necessary.
Get rid of it.
This reverts commit b77532803d ("drm/msm/a6xx: Poll for GBIF unhalt
status in hw_init")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600870/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Memory barriers help ensure instruction ordering, NOT time and order
of actual write arrival at other observers (e.g. memory-mapped IP).
On architectures employing weak memory ordering, the latter can be a
giant pain point, and it has been as part of this driver.
Moreover, the gpu_/gmu_ accessors already use non-relaxed versions of
readl/writel, which include r/w (respectively) barriers.
Replace the barriers with a readback (or drop altogether where possible)
that ensures the previous writes have exited the write buffer (as the CPU
must flush the write to the register it's trying to read back).
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600869/
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dtschema v2024.4, v2024.5 and maybe earlier do not select device nodes for
given binding validation if the schema contains compatible list with
pattern and a const fallback. This leads to binding being a no-op - not
being applied at all. Issue should be fixed in the dtschema but for now
add a work-around do the binding can be used against DTS validation.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600507/
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240623-qcom-adreno-dts-bindings-driver-v2-4-9496410de992@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The frame event callback is always set to dpu_crtc_frame_event_cb() (or
to NULL) and the data is always either the CRTC itself or NULL
(correpondingly). Thus drop the event callback registration, call the
dpu_crtc_frame_event_cb() directly and gate on the dpu_enc->crtc
assigned using dpu_encoder_assign_crtc().
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/600751/
Link: https://lore.kernel.org/r/20240625-dpu-no-crtc-register-v3-1-1b161df13776@linaro.org
Add phy configuration for 28nm dsi phy found on MSM8937 SoC. Only
difference from existing msm8916 configuration is number of phy
and io_start addresses.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600518/
Link: https://lore.kernel.org/r/20240623-dsi-v2-4-a0ca70fb4846@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
CTLs on older qualcomm SOCs like msm8953 and msm8996 has not got interrupts,
so better to skip CTL irq callback register/unregister
make dpu_ctl_cfg be able to define without intr_start.
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/596854/
Link: https://lore.kernel.org/r/20240509-ctl_irq-v1-1-9433f2da9dc7@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Allow board's device tree to specify the vsync source (aka TE source).
If the property is omitted, the display controller driver will use the
default setting.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
[DB: fixed clearing of return value if there is no TE property]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/598740/
Link: https://lore.kernel.org/r/20240613-dpu-handle-te-signal-v2-6-67a0116b5366@linaro.org
The struct msm_display_info has is_te_using_watchdog_timer field which
is neither set anywhere nor is flexible enough to specify different
sources. Replace it with the field specifying the vsync source using
enum dpu_vsync_source.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/598738/
Link: https://lore.kernel.org/r/20240613-dpu-handle-te-signal-v2-5-67a0116b5366@linaro.org
Command mode panels provide TE signal back to the DSI host to signal
that the frame display has completed and update of the image will not
cause tearing. Usually it is connected to the first GPIO with the
mdp_vsync function, which is the default. In such case the property can
be skipped.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/598732/
Link: https://lore.kernel.org/r/20240613-dpu-handle-te-signal-v2-1-67a0116b5366@linaro.org
clear_pending_flush() ctl op is always assigned irrespective of the DPU
hardware revision. Hence there is no needed to check whether the op has
been assigned before calling it.
Drop the checks across the driver for clear_pending_flush() and also
update its documentation that it is always expected to be assigned.
changes in v2:
- instead of adding more validity checks just drop the one for clear_pending_flush
- update the documentation for clear_pending_flush() ctl op
- update the commit text reflecting these changes
changes in v3:
- simplify the documentation of clear_pending_flush
Fixes: d7d0e73f7d ("drm/msm/dpu: introduce the dpu_encoder_phys_* for writeback")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/464fbd84-0d1c-43c3-a40b-31656ac06456@moroto.mountain/T/
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/600241/
Link: https://lore.kernel.org/r/20240620201731.3694593-1-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Make it clear why the pkt_per_line value is being "divided by 2".
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596236/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-6-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Video mode DSC won't work if this field is not set correctly. Set it to fix
video mode DSC (for slice_per_pkt==1 cases at least).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596234/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-5-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The value returned by msm_dsi_wide_bus_enabled() doesn't match what the
driver is doing in video mode. Fix that by actually enabling widebus for
video mode.
Fixes: efcbd6f9cd ("drm/msm/dsi: Enable widebus for DSI")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Patchwork: https://patchwork.freedesktop.org/patch/596232/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-4-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Enable compression bit in cfg2 register for DSC in the DSI case
per hardware version.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596231/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-3-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
data is valid for only half the active window if widebus
is enabled
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596229/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-2-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add width change in DPU timing for DSC compression case to work with
DSI video mode.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596227/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-1-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>