LX2160A pinmux is done in groups by various length bitfields within
configuration registers.
The pinmux nodes i2c7-scl-pins and i2c7-scl-gpio-pins are duplicates of
i2c6-scl-gpio and i2c6-scl-gpio-pins, writing to the same register and
bits.
These two i2c buses i2c6/i2c7 (IIC7/IIC8) are configured together in
register RCWSR13 bits 3-0.
Drop the duplicate node name and change references to the i2c6 node.
Fixes: 8a1365c7bb ("arm64: dts: lx2160a: add pinmux and i2c gpio to support bus recovery")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
LX2160A pinmux is done in groups by various length bitfields within
configuration registers.
The first i2c bus (called IIC1 in reference manual) is configured through
field IIC1_PMUX in register RCWSR14 bit 10 which is described in the
reference manual as a single bit, unlike the other i2c buses.
Change the bitmask for the pinmux nodes from 0x7 to 0x1 to ensure only
single bit is modified.
Further change the zero in the same line to hexadecimal format for
consistency.
Align with documentation by avoiding writes to reserved bits. No functional
change, as writing the extra two reserved bits is not known to cause
issues.
Fixes: 8a1365c7bb ("arm64: dts: lx2160a: add pinmux and i2c gpio to support bus recovery")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Commit 8a1365c7bb ("arm64: dts: lx2160a: add pinmux and i2c gpio to
support bus recovery") introduced pinmux nodes for lx2160 i2c
interfaces, allowing runtime change between i2c and gpio functions
implementing bus recovery.
However, the dynamic configuration area (overwrite MUX) used by the
pinctrl-single driver initially reads as zero and does not reflect the
actual hardware state set by the Reset Configuration Word (RCW) at
power-on.
Because multiple groups of pins are configured from a single 32-bit
register, the first write from the pinctrl driver unintentionally clears
all other bits to zero.
For example, on the LX2162A Clearfog, RCWSR12 is initialized to
0x08000006. When any i2c pinmux is applied, it clears all other fields.
This inadvertently disables SD card-detect (IIC2_PMUX) and some GPIOs
(SDHC1_DIR_PMUX):
LX2162-CF RCWSR12: 0b0000100000000000 0000000000000110
IIC2_PMUX ||| ||| || | ||| |||XXX : I2C/GPIO/CD-WP
SDHC1_DIR_PMUX XXX ||| || | ||| ||| : SDHC/GPIO/SPI
Reverting the commit in question was considered but bus recovery is an
important feature.
Instead add pinmux nodes for those pins that were unintentionally
reconfigured on SolidRun LX2160A Clearfog-CX and LX2162A Clearfog
boards.
Fixes: 8a1365c7bb ("arm64: dts: lx2160a: add pinmux and i2c gpio to support bus recovery")
Cc: stable@vger.kernel.org
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Armbian installs DT overlays using dtbs_install. For it to work all
the overlays have to be added to dtb-y explicitly.
Add the overlays for platforms supported by Armbian.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
MIPI DSI to HDMI bridge ADV7535 CEC default register address is 0x3c
on an I2C bus. And, OV5640 camera uses the same address on the same
I2C bus. To resolve this conflict, use 0x3b as ADV7535 CEC register
address by specifying all ADV7535 register addresses.
Fixes: 6f6c18cba1 ("arm64: dts: imx8mp-evk: add camera ov5640 and related nodes")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The sound card wm8960-2 and wm8960-3 only support capture mode for the
reason of connection on the EVK board. But fsl-asoc-card don't support
capture_only setting, the sound card creation will fail.
fsl-sai 59060000.sai: Missing dma channel for stream: 0
fsl-sai 59060000.sai: ASoC error (-22): at snd_soc_pcm_component_new() on 59060000.sai
fsl-sai 59070000.sai: Missing dma channel for stream: 0
fsl-sai 59070000.sai: ASoC error (-22): at snd_soc_pcm_component_new() on 59070000.sai
so switch to use audio-graph-card2 which supports 'capture_only'
property for wm8960-2 and wm8960-3 cards.
Fixes: b41c45eb99 ("arm64: dts: imx8dxl-evk: add audio nodes")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add pwm fan node and use it for A55 cooling.
Signed-off-by: Florin Leotescu <florin.leotescu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add nxp,ctrl-ids for scmi_misc to support wakeup from the peripherals.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add A55 and ANA thermal including cooling-maps.
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add SCMI sensor/lmm/cpu nodes to allow Linux use thermal, i.MX System
Manager Logical Machine API and CPU API
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add V2X and ELE Message Unit nodes for i.MX94.
One extra V2X MU which is dedicated for V2X fast crypto engine is not
included, because it requires a new compatible string.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Update the pin headers to include pins that has special mux options:
The MUX value field in the IOMUX table is extended to 16 bits where
the lower 8 bits represent the current IOMUX value and the upper
8 bits represent the new extended mux.
Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the following new features:
- SD Card
- Ethernet (FEC + EQOS)
- Wifi
- USB
- HDMI
Signed-off-by: Fabian Pfitzner <f.pfitzner@pengutronix.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the Toradex Verdin iMX95 and its development carrier
board.
The module consists of an NXP i.MX95 family SoC, up to 16GB LPDDR4x RAM,
up to 128GB of storage, a USB 3.2 OTG and USB 2.0 Host, a Gigabit
Ethernet PHY, an I2C EEPROM and Temperature Sensor, an RX8130 RTC, an
I3C bus, one Quad lane CSI interface, one Quad lane DSI or CSI
interface, one LVDS interface (one or two channels), and some optional
addons: TPM 2.0, and a WiFi/BT module.
Link: https://www.toradex.com/computer-on-modules/verdin-arm-family/nxp-imx95
Link: https://www.toradex.com/products/carrier-board/verdin-development-board-kit
Co-developed-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Co-developed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add the vcc power supply for the BT device. Fixes the warning:
btnxpuart serial0-0: supply vcc not found, using dummy regulator
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
This overlay enables the LWB5+ M.2 wlan module from ezurio.
Signed-off-by: Martin Schmiedel <Martin.Schmiedel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for TQMa93xx module attached to MBa93xxLA-MINI board. TQMa93xx
is a SOM series using i.MX93 SOC.
The MBa93xxLA-MINI has a small form factor and is designed with WLAN,
Bluetooth and WWAN applications in mind.
Signed-off-by: Martin Schmiedel <Martin.Schmiedel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add an overlay for the supported LVDS display AUO G133HAN01. Apply
it for both TQMa8MxML and TQMa8MxNL.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Now that the bindings supports IRQ, add the IRQ line. Add a GPIO label
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Now we use vpcie3v3aux-supply to keep 3.3Vaux supply enabled for the
entire PCIe controller lifecycle, no need regulator-always-on property.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add PDM micphone sound card support, configure the pinmux.
This sound card supports recording sound from PDM microphone
and convert the PDM format data to PCM data.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add wm8962 sound card. By connecting with ASRC1, the sound card support
sample rate conversion. ASRC2 is also enabled, which can provide memory
to memory user interface.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add audio device nodes, include SAI, MICFIL, ASRC, Audio Mixer.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Sonata carrier board with
the DART-MX95 system on module.
The Sonata board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- 10Gb Ethernet SFP+ connector
- Uart interfaces
- OV5640 Camera support
- GPIO Expanders
- RTC module
- TPM module
- PCIE support
Link: https://variscite.com/carrier-boards/sonata-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite DART-MX95 system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX95 MPU processor
- Up to 16GB of LPDDR5 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-9/i-mx-95/dart-mx95/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite Sonata carrier board with
the DART-MX91 system on module.
The Sonata board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart interfaces
- GPIO Expanders
- RTC module
- TPM module
Link: https://variscite.com/carrier-boards/sonata-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add device tree support for the Variscite DART-MX91 system on module.
This SOM is designed to be used with various carrier boards.
The module includes:
- NXP i.MX91 MPU processor
- Up to 2GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth
Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.
Link: https://variscite.com/system-on-module-som/i-mx-9/i-mx-91/dart-mx91/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The 'funnel' node does not contain a register range, so it should
be placed outside of the soc node to fix schema warnings from
simple-bus.yaml.
Change is similar to commit 9cfe3c892b ("arm64: dts: imx8mp: Move
funnel outside from soc")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The DSI burst clock frequency is too high resulting in flickering. Reduce
the frequency.
While at it, remove the burst clock from board configuration as it is
display specific.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The DSI burst clock frequency is too high resulting in flickering. Reduce
the frequency.
While at it, remove the burst clock from board configuration as it is
display specific.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Since commit a0deedcc0c ("arm64: dts: imx8mm: Slow default video_pll1
clock rate") and commit 5fe6ec93f1 ("clk: imx8mm: Let
IMX8MM_CLK_LCDIF_PIXEL set parent rate") VIDEO_PLL1 is dynamically
programmed by CLK_LCDIF_PIXEL.
On imx8mm-tqma8mqml-mba8mx-lvds-tm070jvhg33.dtso this results in a
VIDEO_PLL1 frequency of 68.2 MHz and DSI_PHY_REF of 17.05MHz (1/4).
Instead use the 24 MHz clock as parent for DSI PHY reference clock.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the SolidRun i.MX8M Mini SoM on HummingBoard Ripple.
The SoM features:
- 1Gbps Ethernet with PHY
- eMMC
- 1/2GB DDR
- NPU (assembly option)
- WiFi + Bluetooth
The HummingBoard Ripple features:
- 2x USB-2.0 Type-A connector
- 1Gbps RJ45 Ethernet with PoE
- microSD connector
- microHDMI connector
- mpcie connector with USB-2.0 interface + SIM card holder
- microUSB connector for console (using fdtdi chip)
- RTC with backup battery
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the SolidRun SolidSense N8 Compact.
The board is designed around the i.MX8MN SoC and comes as a complete
product including enclosure and labels.
Features:
- USB-2.0 Type A connector
- 1Gbps RJ45 Ethernet with PoE
- microSD connector
- eMMC
- Cellular Modem + SIM holder
- WiFi + Bluetooth
- RS485
- CAN
- 802.15.1 radio
- supercapacitor backup power supply
This is a headless design without display.
The board includes an internal expansion connector for daughterboards
which may be described by dt addon.
The supercap is not currently described due to lack of suitable bindings.
Vendor BSP uses gpio-keys driver to trigger shutdown on power loss.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The SolidRun i.MX8MP HummingBoard IIoT has a variety of connectors, and
configurable ports:
- 2x RS232
- 2x RS485
- DSI Panel Connector
- LVDS Panel Connector
RS232 and RS485 each share a single UART from the SoC via a mux, which
are configured from the base dts for RS232 by default.
Provide addons for:
1. Reconfigure UART A from RS232 to RS485.
2. Reconfigure UART B from RS232 to RS485.
3. Configure DSI Connector for Winstar WJ70N3TYJHMNG0 Panel.
4. Configure LVDS Connector for Winstar WF70A8SYJHLNGA Panel.
A variation of the base dtb is generated for each addon to ensure that
make dtbs_check covers the resulting dtb, and applying overlay is
tested during build.
It is however expected that bootloader should apply any combination of
addons based on runtime configuration.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Introduce support for the SolidRun i.MX8MP HummingBoard IIoT platform.
This board is a new design based on the i.MX8MP System on Module and
does not share much hardware with previous HummingBoard variants.
It comes with some common features:
- 3x USB-3.0 Type A connector
- 2x 1Gbps RJ45 Ethernet
- USB Type-C Console Port
- microSD connector
- RTC with backup battery
- RGB Status LED
- 1x M.2 M-Key connector with PCI-E Gen. 3 x1
- 1x M.2 B-Key connector with USB-2.0/3.0 + SIM card holder
- 1x LVDS Display Connector
- 1x DSI Display Connector
- GPIO header
- 2x RS232/RS485 ports (configurable)
- 2x CAN
In addition there is a board-to-board expansion connector to support
custom daughter boards with access to SPI, a range of GPIOs and -
notably - CAN and UART. Both 2x CAN and 2x UART can be muxed either
to this b2b connector, or a terminal block connector on the base board.
The routing choice for UART and CAN is expressed through gpio
mux-controllers in DT and can be changed by applying dtb overlays.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable PCIe support on the VAR-SOM Symphony carrier board by adding the
external reference clock, configuring the PHY and providing the required
clock and reset properties.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable I2C4 on the Symphony carrier and add pinctrl configuration,
including GPIO-based bus recovery support.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the TPM2 device on the VAR-SOM Symphony carrier board.
The ST33K TPM2 is connected over I2C, and A PCA6408 GPIO expander is
used to control the reset signal required to release the TPM from reset.
Add the PCA6408 GPIO expander and the ST33K TPM2 device node.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Enable the microSD slot on the VAR-SOM Symphony carrier board.
Configure USDHC2 with card-detect GPIO, pinctrl states for the supported
bus speeds and the required VMMC supply.
Update the VMMC regulator to match the latest carrier revision by moving
the enable GPIO to GPIO4_IO22 and adding the required off-on delay.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Move the USB controller configuration out of the i.MX8MM VAR-SOM dtsi
and into the VAR-SOM Symphony carrier board dts.
The SOM does not provide any USB connectors and carrier boards may
choose whether and how to route USB, therefore USB should be described
in the carrier-specific device tree instead of the SOM include.
While moving the nodes, align the Symphony USB description with the
carrier design by enabling both USB controllers, wiring USB1 to the
PTN5150 Type-C controller for dual-role operation, and updating the
PHY tuning and VBUS regulator pinctrl (including a sleep state).
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The VAR-SOM-MX8MM currently integrates the NXP IW61x wireless module,
providing WiFi over SDIO and Bluetooth over UART.
Move the wireless module configuration out of the base
imx8mm-var-som.dtsi and provide dedicated variant includes.
The IW61x configuration is moved to imx8mm-var-som-wifi-bt-iw61x.dtsi
and used by the Symphony evaluation board device tree.
A separate imx8mm-var-som-wifi-brcm-legacy.dtsi include is added to keep
the configuration for the legacy Broadcom SDIO WiFi module used on
earlier SOM revisions.
To preserve compatibility with older SOM revisions, add a separate
imx8mm-var-som-symphony-legacy.dtb, which disables the IW61x setup and
applies the Broadcom-specific configuration.
The Broadcom-based SOM revision is no longer in production, but support
is kept for existing users.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Add support for the Microchip MCP251xFD CAN-FD controller connected
to the SPI bus on the i.MX8MM VAR-SOM.
The controller uses a 40 MHz external oscillator and requires an
interrupt line and a dedicated RX interrupt GPIO.
Add the fixed clock, the MCP251xFD device node with the required
properties, and the corresponding pinctrl configuration.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
The VAR-SOM-MX8MM can integrate the WM8904, a high-performance
ultra-low-power stereo codec optimized for portable audio applications.
Add the WM8904 device to the appropriate I2C bus, enable the SAI
peripheral, and introduce the sound node to expose the sound card to the
system.
Add I3C recovery gpio properties.
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
