[ Upstream commit 6edf2e3710 ]
This patch fixes the udmabuf selftest. Currently the selftest is broken.
I fixed the selftest by setting the F_SEAL_SHRINK seal on the memfd
file descriptor which is required by udmabuf and added the test to
the selftest Makefile.
Signed-off-by: Tom Murphy <murphyt7@tcd.ie>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit add6883619 ]
eukrea-tlv320.c machine driver runs on non-DT platforms
and include <asm/mach-types.h> header file in order to be able
to use some machine_is_eukrea_xxx() macros.
Building it for ARM64 causes the following build error:
sound/soc/fsl/eukrea-tlv320.c:28:10: fatal error: asm/mach-types.h: No such file or directory
Avoid this error by not allowing to build the SND_SOC_EUKREA_TLV320
driver when ARM64 is selected.
This is needed in preparation for the i.MX8M support.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88af3209aa ]
WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info()
The function littleton_init_lcd() references
the function __init pxa_set_fb_info().
This is often because littleton_init_lcd lacks a __init
annotation or the annotation of pxa_set_fb_info is wrong.
WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info()
The function zeus_register_ohci() references
the function __init pxa_set_ohci_info().
This is often because zeus_register_ohci lacks a __init
annotation or the annotation of pxa_set_ohci_info is wrong.
WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info()
The function cm_x300_init_u2d() references
the function __init pxa3xx_set_u2d_info().
This is often because cm_x300_init_u2d lacks a __init
annotation or the annotation of pxa3xx_set_u2d_info is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0517a0f7e ]
For some reason, my older GCC (< 4.8) isn't smart enough to optimize the
!__builtin_constant_p() branch in bpf_htons, I see:
error: implicit declaration of function '__builtin_bswap16'
Let's use __bpf_constant_htons as suggested by Daniel Borkmann.
I tried to use simple htons, but it produces the following:
test_progs.c:54:17: error: braced-group within expression allowed only
inside a function
.eth.h_proto = htons(ETH_P_IP),
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4a7dca5de ]
In the ioctl_event_ctl() SWITCHTEC_IOCTL_EVENT_IDX_ALL case, we call
event_ctl() several times with the same "ctl" struct. Each call clobbers
ctl.flags, which leads to the problem that we may not actually enable or
disable all events as the user requested.
Preserve the event flag value with a temporary variable.
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d288d95842 ]
When inode is corrupted so that extent type is invalid, some functions
(such as udf_truncate_extents()) will just BUG. Check that extent type
is valid when loading the inode to memory.
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7263ab35b ]
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2659392e5c ]
The new Allwinner H6 SoC's USB2 PHY has two holes -- USB1 (which is a
3.0 port with dedicated PHY) and USB2 (which doesn't exist at all).
Add support for this kind of missing USB PHY index.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55e58c5e78 ]
With gcc 4.1:
drivers/lightnvm/core.c: In function ‘nvm_get_bb_meta’:
drivers/lightnvm/core.c:977: warning: ‘ret’ may be used uninitialized in this function
and
drivers/nvme/host/lightnvm.c: In function ‘nvme_nvm_get_chk_meta’:
drivers/nvme/host/lightnvm.c:580: warning: ‘ret’ may be used uninitialized in this function
Indeed, if (for the former) the number of channels or LUNs is zero, or
(for both) the passed number of chunks is zero, ret will be returned
uninitialized.
Fix this by preinitializing ret to zero.
Fixes: aff3fb18f9 ("lightnvm: move bad block and chunk state logic to core")
Fixes: a294c19945 ("lightnvm: implement get log report chunk helpers")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5c85fe3a ]
It was observed that when using seqentional mode contrary to the
documentation, the SS bit (which is supposed to only be set if
automatic/sequence command completed normally), is sometimes set
together with NA (NAK in address phase) causing transfer to falsely be
considered successful.
My assumption is that this does not happen during manual mode since the
controller is stopping its work the moment it sets NA/ND bit in status
register. This is not the case in Automatic/Sequentional mode where it
is still working to send STOP condition and the actual status we get
depends on the time when the ISR is run.
This patch changes the order of checking status bits in ISR - error
conditions are checked first and only if none of them occurred, the
transfer may be considered successful. This is required to introduce
using of sequentional mode in next patch.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fde201a466 ]
Protect the list_add on the pblk_line_init_bb() error
path in case this code is used for some other purpose
in the future.
Signed-off-by: Hua Su <suhua.tanke@gmail.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12fa401ac ]
Make sure we only look up valid lba addresses on the resubmission path.
If an lba is invalidated in the write buffer, that sector will be
submitted to disk (as it is already mapped to a ppa), and that write
might fail, resulting in a crash when trying to look up the lba in the
mapping table (as the lba is marked as invalid).
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Javier González <javier@javigon.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f79e03b1f ]
There exists a case where a flush of a plane/dma may have been triggered
& started from an async commit. If that plane/dma is subsequently disabled
by the next commit, the flush register will continue to hold the flush
bit for the disabled plane. Since the bit remains active,
pending_kickoff_cnt will never decrement and we'll miss frame_done
events.
This patch limits the check of flush_register to include only those bits
which have been updated with the latest commit.
Changes in v2:
- None
Reviewed-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1866d44d1 ]
Fix the dsi clock names in the DSI 10nm PLL driver to
match the names in the dispcc driver as those are
according to the clock plan of the chipset.
Changes in v2:
- Update the clock diagram with the new clock name
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2d102bd01 ]
This bug occurs when:
- a new request arrives, one thread(let's call it A) is pending in
optee_supp_req() with req->busy is initial value false.
- tee-supplicant is killed, then optee_supp_release() is called, this
function calls list_del(&req->link), and set supp->ctx to NULL. And
it also wake up process A.
- process A continues, it firstly checks supp->ctx which is NULL,
then checks req->busy which is false, at last run list_del(&req->link).
This triggers double list_del() and results kernel panic.
For solve this problem, we rename req->busy to req->in_queue, and
associate it with state of whether req is linked to supp->reqs. So we
can just only check req->in_queue to make decision calling list_del()
or not.
Signed-off-by: Zhizhou Zhang <zhizhouzhang@asrmicro.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90e3577b5f ]
The value of opp_table->regulator_count is not very consistent right now
and it may end up being 0 while we do have a "opp-microvolt" property in
the OPP table. It was kept that way as we used to check if any
regulators are set with the OPP core for a device or not using value of
regulator_count.
Lets use opp_table->regulators for that purpose as the meaning of
regulator_count is going to change in the later patches.
Reported-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9456823c84 ]
of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
bl_idle_init() doesn't do that, so fix it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edd45cba5e ]
Shift by one the registers for tachometers (7 - 12).
This fix is relevant for the same new systems MQMB7, MSN37, MSN34,
which are about to be released to the customers.
At the moment, none of them is at customers sites. The customers will
not suffer from this change.
This fix is necessary, because register used before for tachometer 7
has been than reserved for the second PWM for newer systems, which are
not supported yet in mlx-platform driver. So registers of tachometers
7-12 have been shifted by one.
Fixes: 0378123c58 ("platform/x86: mlx-platform: Add mlxreg-fan platform driver activation")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0efcc2c0fd ]
Same as other i.MX6 SoCs, ensure unused MMDC channel's
handshake is bypassed, this is to make sure no request
signal will be generated when periphe_clk_sel is changed
or SRC warm reset is triggered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f83cfdb1a ]
The driver overrides the error codes returned by platform_get_irq() to
-EINVAL, so if it returns -EPROBE_DEFER, the driver would fail the probe
permanently instead of the deferred probing. Switch to propagating the
error code upstream, still checking/overriding IRQ0 as libata regards it
as "no IRQ" (thus polling) anyway...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a868e85304 ]
After removing an entry from a queue (e.g. reading an event in
arm_smmu_evtq_thread()) it is necessary to advance the MMIO consumer
pointer to free the queue slot back to the SMMU. A memory barrier is
required here so that all reads targetting the queue entry have
completed before the consumer pointer is updated.
The implementation of queue_inc_cons() relies on a writel() to complete
the previous reads, but this is incorrect because writel() is only
guaranteed to complete prior writes. This patch replaces the call to
writel() with an mb(); writel_relaxed() sequence, which gives us the
read->write ordering which we require.
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89cddc5637 ]
qcom,smmu-v2 is an arm,smmu-v2 implementation with specific
clock and power requirements.
On msm8996, multiple cores, viz. mdss, video, etc. use this
smmu. On sdm845, this smmu is used with gpu.
Add bindings for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84a9a75774 ]
The GITS_TRANSLATER MMIO doorbell register in the ITS hardware is
architected to be 4 bytes in size, yet on hi1620 and earlier, Hisilicon
have allocated the adjacent 4 bytes to carry some IMPDEF sideband
information which results in an 8-byte MSI payload being delivered when
signalling an interrupt:
MSIAddr:
|----4bytes----|----4bytes----|
| MSIData | IMPDEF |
This poses no problem for the ITS hardware because the adjacent 4 bytes
are reserved in the memory map. However, when delivering MSIs to memory,
as we do in the SMMUv3 driver for signalling the completion of a SYNC
command, the extended payload will corrupt the 4 bytes adjacent to the
"sync_count" member in struct arm_smmu_device. Fortunately, the current
layout allocates these bytes to padding, but this is fragile and we
should make this explicit.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[will: Rewrote commit message and comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 244add8ebf ]
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79da07dec7 ]
TPA6130A2 SD pin on RDU1 is not really controlled by SoC and instead
is only meant to notify the system that audio was "muted" by external
actors. To accommodate that, drop "power-gpio" property of hpa1 node as
well as specify a name for that GPIO so that userspace can access it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e990e12741 ]
The datasheet says we must stop the timer before changing the clock
divider. This can happen when the restart handler is called while the
watchdog is running.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 738a05e673 ]
The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:
dev: size erasesize name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"
Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b3e6f8999 ]
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: feb3cbea09 ("ARM64: dts: meson-gxbb-odroidc2: fix GbE tx link breakage")
Fixes: 6d28d57751 ("ARM64: dts: meson-axg: fix ethernet stability issue")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75fa6e4f83 ]
Add support for the third loop filter mode
V4L2_MPEG_VIDEO_H264_LOOP_FILTER_MODE_DISABLED_AT_SLICE_BOUNDARY,
and fix V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_ALPHA and
V4L2_CID_MPEG_VIDEO_H264_LOOP_FILTER_BETA controls.
The filter offset controls are signed values in the -6 to 6 range and
are stored into the slice header fields slice_alpha_c0_offset_div2 and
slice_beta_offset_div2. The actual filter offsets FilterOffsetA/B are
double their value, in range of -12 to 12.
Rename variables to more closely match the nomenclature in the H.264
specification.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17f6c83fb5 ]
For micro-mips, srlv inside POOL32A encoding space should use 0x50
sub-opcode, NOT 0x90.
Some early version ISA doc describes the encoding as 0x90 for both srlv and
srav, this looks to me was a typo. I checked Binutils libopcode
implementation which is using 0x50 for srlv and 0x90 for srav.
v1->v2:
- Keep mm_srlv32_op sorted by value.
Fixes: f31318fdf3 ("MIPS: uasm: Add srlv uasm instruction")
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84fb6c7feb ]
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2afdb4c41d ]
Since commit 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. Believed to be unused GPIO
pin "hookflash1", apparently set high regardless of the corresponding
bit of "latch2" port attempted to be set low during .init_machine(),
has been identified as the reason.
According to Amstrad E3 wiki, the purpose of the pin hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on it when the phone was taken off hook or recall was pressed.
With the current finding, we can assume the pin provides a kind of
audio mute function.
Proper resolution of the issue should be done in two steps:
- resolution of an issue with the pin state not reflecting the value
the corresponding bit of the port was attempted to be initialized
with,
- extension of on-board audio driver with a new control.
For now, rename the pin to "audio_mute" to reflect its function and,
as a quick fix, hogg it as output low so on-board audio can produce
audible sound again.
Fixes: 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee494cf377 ]
Currently v4l2_device_register_subdev_nodes() does not initialize the
dev_parent field of the video_device structs it creates for subdevices
being registered. This leads to __video_register_device() falling back
to the parent device of associated v4l2_device struct, which often does
not match the physical device the subdevice is registered for.
Due to the problem above, the links between real devices and v4l-subdev
nodes cannot be obtained from sysfs, which might be confusing for the
userspace trying to identify the hardware.
Fix this by initializing the dev_parent field of the video_device struct
with the value of dev field of the v4l2_subdev struct. In case of
subdevices without a parent struct device, the field will be NULL and the
old behavior will be preserved by the semantics of
__video_register_device().
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c12b08ebbe ]
The parameter is still there but it's ignored. We need to check its
value before deciding to go into passthrough mode for AMD IOMMU v2
capable device.
We occasionally use this parameter to force v2 capable device into
translation mode to debug memory corruption that we suspect is
caused by DMA writes.
To address the following comment from Joerg Roedel on the first
version, v2 capability of device is completely ignored.
> This breaks the iommu_v2 use-case, as it needs a direct mapping for the
> devices that support it.
And from Documentation/admin-guide/kernel-parameters.txt:
This option does not override iommu=pt
Fixes: aafd8ba0ca ("iommu/amd: Implement add_device and remove_device")
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d9f6b83f ]
devm_kstrdup() may return NULL if internal allocation failed.
Thus using label, name is unsafe without checking. Therefor
in the unlikely case of allocation failure, sx150x_probe() simply
returns -ENOMEM.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 9e80f9064e ("pinctrl: Add SX150X GPIO Extender Pinctrl Driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a109c2dbb5 ]
The error cases of mediatek_gpio_bank_probe() would go unnoticed (except
for the dev_err() messages). The probe function should return an error
if one of the banks failed to initialize properly indicated by
not returning non-0.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d646c775 ]
kasprintf() may return NULL on failure of internal allocation thus the
assigned label is not safe if not explicitly checked. On error
mediatek_gpio_bank_probe() returns negative values so -ENOMEM in the
(unlikely) failure case should be fine here.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54d48183d2 ]
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d73 ("usb: dwc3: trace: pretty print high-bandwidth transfers too")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca95f802ef ]
Currently, When a reserved operation is completed, its entry in the send
queue will not be unreserved, which leads to the miscalculation of
qp->s_avail and thus the triggering of a WARN_ON call trace. This patch
fixes the problem by unreserving the reserved operation when it is
completed.
Fixes: 856cc4c237 ("IB/hfi1: Add the capability for reserved operations")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df44b47965 ]
Propagate error code back to userspace if writing the /sys/.../uevent
file fails. Before, the write operation always returned with success,
even if we failed to recognize the input string or if we failed to
generate the uevent itself.
With the error codes properly propagated back to userspace, we are
able to react in userspace accordingly by not assuming and awaiting
a uevent that is not delivered.
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c37d721c68 ]
Move the async_synchronize_full call out of __device_release_driver and
into driver_detach.
The idea behind this is that the async_synchronize_full call will only
guarantee that any existing async operations are flushed. This doesn't do
anything to guarantee that a hotplug event that may occur while we are
doing the release of the driver will not be asynchronously scheduled.
By moving this into the driver_detach path we can avoid potential deadlocks
as we aren't holding the device lock at this point and we should not have
the driver we want to flush loaded so the flush will take care of any
asynchronous events the driver we are detaching might have scheduled.
Fixes: 765230b5f0 ("driver-core: add asynchronous probing support for drivers")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 690e16bada ]
Rockpro64 is not able boot if GPIO1_C1 pin is pulled high
before loading linux kernel.
In rockpro64 GPIO1_C1 pin is connected vdd_cpu_b regulator
VSEL pin. Pin should be pulled down in normal operation and
pulled high in suspend.
PMIC LDO_REG2 is connected to touch panel connector.
Rename regulator and set it to correct voltage.
PCIe power is controller by GPIO1_D0.
Schematics can be downloaded from:
http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Acked-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5d6c3e5a3 ]
When setting LINK tolerance, node timer interval will be calculated
base on the LINK with lowest tolerance.
But when calculated, the old node timer interval only updated if current
setting value (tolerance/4) less than old ones regardless of number of
links as well as links' lowest tolerance value.
This caused to two cases missing if tolerance changed as following:
Case 1:
1.1/ There is one link (L1) available in the system
1.2/ Set L1's tolerance from 1500ms => lower (i.e 500ms)
1.3/ Then, fallback to default (1500ms) or higher (i.e 2000ms)
Expected:
node timer interval is 1500/4=375ms after 1.3
Result:
node timer interval will not being updated after changing tolerance at 1.3
since its value 1500/4=375ms is not less than 500/4=125ms at 1.2.
Case 2:
2.1/ There are two links (L1, L2) available in the system
2.2/ L1 and L2 tolerance value are 2000ms as initial
2.3/ Set L2's tolerance from 2000ms => lower 1500ms
2.4/ Disable link L2 (bring down its bearer)
Expected:
node timer interval is 2000ms/4=500ms after 2.4
Result:
node timer interval will not being updated after disabling L2 since
its value 2000ms/4=500ms is still not less than 1500/4=375ms at 2.3
although L2 is already not available in the system.
To fix this, we start the node interval calculation by initializing it to
a value larger than any conceivable calculated value. This way, the link
with the lowest tolerance will always determine the calculated value.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4be1eaf322 ]
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignment to .label is not safe if not checked. On error
npcm7xx_gpio_of() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 3b588e43ee ("pinctrl: nuvoton: add NPCM7xx pinctrl and GPIO driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6c7f03f69 ]
The iTXQs stop/wake queue mechanism involves a whole bunch
of locks and this is probably why the call to
ieee80211_wake_txqs is deferred to a tasklet when called from
__ieee80211_wake_queue.
Another advantage of that is that ieee80211_wake_txqs might
call the wake_tx_queue() callback and then the driver may
call mac80211 which will call it back in the same context.
The bug I saw is that when we send a deauth frame as a
station we do:
flush(drop=1)
tx deauth
flush(drop=0)
While we flush we stop the queues and wake them up
immediately after we finished flushing. The problem here is
that the tasklet that de-facto enables the queue may not have
run until we send the deauth. Then the deauth frame is sent
to the driver (which is surprising by itself), but the driver
won't get anything useful from ieee80211_tx_dequeue because
the queue is stopped (or more precisely because
vif->txqs_stopped[0] is true).
Then the deauth is not sent. Later on, the tasklet will run,
but that'll be too late. We'll already have removed all the
vif etc...
Fix this by calling ieee80211_wake_txqs synchronously if we
are not waking up the queues from the driver (we check the
reason to determine that). This makes the code really
convoluted because we may call ieee80211_wake_txqs from
__ieee80211_wake_queue. The latter assumes that
queue_stop_reason_lock has been taken by the caller and
ieee80211_wake_txqs may release the lock to send the frames.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e6da2039c ]
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0678e2eed ]
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce10a5b395 ]
tk_core.seq is initialized open coded, but that misses to initialize the
lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq
consequently lack a name and are hard to read.
Use the proper initializer which takes care of the lockdep map
initialization.
[ tglx: Massaged changelog ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: tj@kernel.org
Cc: johannes.berg@intel.com
Link: https://lkml.kernel.org/r/20181128234325.110011-12-bvanassche@acm.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
