When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: Paul Bender <pebender@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are cases where we get an ending space, and our trailing timeout
space then gets sent right after it, which breaks repeat, at least for
lirc userspace decoding. Merge the two spaces by way of using
ir_raw_event_store_filter, set a timeout value, and we're back to good.
Successfully tested with streamzap and windows mce remotes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This removes the '+1' in vsync timing calculation for wm8505fb to
directly use values provided from the board setup code.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This replaces the last remaining driver name reference with the
macro for uniformity in wm8505fb.
In addition, the error return path in wmt_ge_rops.c is made more
uniform by getting rid of goto's in remaining places.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Silence warnings such as -
drivers/video/s1d13xxxfb.c:421: warning: ‘bltbit_wait_bitset’ defined but not used
Just drop the unused code.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for runtime pm using the functions.
- pm_runtime_get_sync()
- pm_runtime_put_sync()
pm_runtime_get_sync() and pm_runtime_put_sync() are called when
open or release function of framebufer driver is called to inform
the system if hardware is idle or not.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On PXA320, there's only one PCMCIA slot available. Check for cases where the
user would want to register multiple. Also, rework failpath.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This also converts tc3589x to the new irq API.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Manaul revert of 0cdab21f9a, just to
remove the call to disable the clock gatings and powerctx before
suspend.
Peter Clifton bisected a suspend failure on his gme45 and found this to
be the culprit. As this was intended to be a fix for a similar suspend
failure for Ironlake (it didn't work), undoing this patch should have no
other side-effects.
Reported-and-tested-by: Peter Clifton <pcjc2@cam.ac.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The relative-to-general state default is useless as it means having to
rewrite the streaming kernels for each batch. Relative-to-surface is
more useful, as that stream usually needs to be rewritten for each
batch. And absolute addressing mode, vital if you start streaming
state, is also only available by adjusting the register...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Looking at the uevent stream for input devices, all properties are on
the form "A=B" except the bitmap values, which are on the form
"A==B". This bug has been around at least since 2007, and the input
uevent code has been untouched since. The recent addition of device
properties suggests this is a good time for a remedy.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Today, userspace sets up an input device based on the data it emits.
This is not always enough; a tablet and a touchscreen may emit exactly
the same data, for instance, but the former should be set up with a
pointer whereas the latter does not need to. Recently, a new type of
touchpad has emerged where the buttons are under the pad, which
changes logic without changing the emitted data. This patch introduces
a new ioctl, EVIOCGPROP, which enables user access to a set of device
properties useful during setup. The properties are given as a bitmap
in the same fashion as the event types, and are also made available
via sysfs, uevent and /proc/bus/input/devices.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Commit a8adbe3 forgot to remove the return variable, kill it.
drivers/block/loop.c: In function 'lo_splice_actor':
drivers/block/loop.c:398: warning: unused variable 'ret'
[...]
fs/nfsd/vfs.c: In function 'nfsd_splice_actor':
fs/nfsd/vfs.c:848: warning: unused variable 'ret'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 6e07ebd84 (drivers/net: remove unnecessary
flush_scheduled_work() calls) incorrectly removed the flush call
without replacing it with the appropriate work specific operation.
Fix it by flushing vdev->reset_task explicitly.
Pointed out by Jon Mason.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jon Mason <jon.mason@exar.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ri_tasklet(), we run from softirq, so can directly handle packet
through netif_receive_skb() instead of netif_rx().
There is no risk of recursion.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
Skip putting the GPIO module into a reset during the chip init. This makes
sure to preserve any existing GPIO configurations done by pre-kernel boot code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
On the TC35892, a random delayed interrupt clear (GPIO IC) write locks up the
child interrupts. In such a case, the original interrupt is active and not yet
acknowledged. Re-check the IRQST bit for any pending interrupts and handle
those.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Add block identifier to be able to add multiple mfd clients
to the mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the tc35892 core/gpio drivers to tc3589x to include
new variants in the same mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
I misread the datasheet as if bypass mode was not available at all
on the ux500's, I was wrong. It is there, the datasheet just
states that you should not have to use it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Ux500 variant of this block has a different divider.
The value used right now is too big and which means a loss
in performance. This fix corrects it. Also expand the math
comments a bit so it's clear what's happening. Further
the Ux500 variant does not like if we use the BYPASS bit,
instead we are supposed to set the clock divider to zero.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
At ifup, carrier status would be shown on even if it actually was off.
Also add an include for ethtool_ops rather than to rely on the one from
netdevice.h.
Note, we can alas not use fwnet_device_mutex to serialize access to
dev->peer_count (as I originally wanted). This would cause a lock
inversion:
- fwnet_probe | takes fwnet_device_mutex
+ register_netdev | takes rtnl_mutex
- devinet_ioctl | takes rtnl_mutex
+ fwnet_open | ...must not take fwnet_device_mutex
Hence use the dev->lock spinlock for serialization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
To make userland, e.g. NetworkManager work with firewire, we need to
detect whether cable is plugged or not. Simple and correct way of doing
that is just counting number of peers. No peers - no link and vice
versa.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
Add an interrupt handler for switching graphics frequencies and handling
PM interrupts. This should allow for increased performance when busy
and lower power consumption when idle.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch adds support for another Wetab device (726b), and grabs it
accordingly in hid-core.
[rydberg@euromail.se: rename and log message changes]
Signed-off-by: Andy Ross <andy@plausible.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>