It's not clear what was the intention of redundant usage of IS_ERR()
around the clock pointer since with the error check of devm_clk_get()
followed by bailout it can't be invalid,
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). It will allow to switch to device properties
approach in the future.
Link: https://lore.kernel.org/all/20211206165542.69887-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Allwinner R40 (also known as A40i, T3, V40) has a CAN controller. The
controller is the same as in earlier A10 and A20 SoCs, but needs reset
line to be deasserted before use.
This patch adds a CAN node and the corresponding pinctrl descriptions.
Link: https://lore.kernel.org/all/20211122104616.537156-4-boger@wirenboard.com
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Allwinner R40 (also known as A40i, T3, V40) has a CAN controller. The
controller is the same as in earlier A10 and A20 SoCs, but needs reset
line to be deasserted before use.
This patch adds a new compatible for R40 CAN controller. Depending
on the compatible, reset line can be requested from DT.
Link: https://lore.kernel.org/all/20211122104616.537156-3-boger@wirenboard.com
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Allwinner R40 (also known as A40i, T3, V40) has a CAN controller. The
controller is the same as in earlier A10 and A20 SoCs, but needs reset
line to be deasserted before use.
This patch Introduces new compatible for R40 CAN controller with
required resets property.
Link: https://lore.kernel.org/all/20211122104616.537156-2-boger@wirenboard.com
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In [1], we introduced a set of units in linux/can/bittiming.h. Since
then, generic SI prefixes were added to linux/units.h in [2]. Those
new prefixes can perfectly replace CAN specific ones.
This patch replaces all occurrences of the CAN units with their
corresponding prefix (from linux/units) and the unit (as a comment)
according to below table.
CAN units SI metric prefix (from linux/units) + unit (as a comment)
------------------------------------------------------------------------
CAN_KBPS KILO /* BPS */
CAN_MBPS MEGA /* BPS */
CAM_MHZ MEGA /* Hz */
The definition are then removed from linux/can/bittiming.h
[1] commit 1d7750760b ("can: bittiming: add CAN_KBPS, CAN_MBPS and
CAN_MHZ macros")
[2] commit 26471d4a6c ("units: Add SI metric prefix definitions")
Link: https://lore.kernel.org/all/20211124014536.782550-1-mailhol.vincent@wanadoo.fr
Suggested-by: Jimmy Assarsson <extja@kvaser.com>
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Clock and Power Domain definitions for the Renesas R-Car S4-8 (R8A77FA0)
SoC, shared by driver and DT source files.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYa9+OQAKCRCKwlD9ZEnx
cDY/AQDGyN++TeRgG8j5U2XcWJw7mfOwh6M4zN+0TO6yl++5JwD/e1Q7okUEdzqC
dBV0H15huLHJ/ygFgZaDQeDStybQAw4=
=VF9E
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a779f0-dt-binding-defs-tag' into HEAD
Renesas R-Car S4-8 DT Binding Definitions
Clock and Power Domain definitions for the Renesas R-Car S4-8 (R8A77FA0)
SoC, shared by driver and DT source files.
While running stress tests in roaming scenarios (switching ap's every 5
seconds, we discovered a issue which leads to tx hangings of exactly 5
seconds while or after scanning for new accesspoints. We found out that
this hanging is triggered by ath10k_mac_wait_tx_complete since the
empty_tx_wq was not wake when the num_tx_pending counter reaches zero.
To fix this, we simply move the wake_up call to htt_tx_dec_pending,
since this call was missed on several locations within the ath10k code.
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210505085806.11474-1-s.gottschall@dd-wrt.com
South Korea manufacturer, Samsung, has extended South Korea
regulatory domain pair with 0x5F and has used it for their
devices such as Samsung Galaxy book. Hence add support
0x5F as a regulatory domain pair along with extended country
code, 413.
Signed-off-by: Peter Oh <ebmajor.dev@gmail.com>
Signed-off-by: Andreas Tepe <andreas.tepe@debitel.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20210915185611.6195-1-ebmajor.dev@gmail.com
In ath11k, tx of management packet is doing in a work queue. Sometimes
the workqueue does not finish tx immediately, then it lead after the next
step of vdev delete finished, it start to send the management packet to
firmware and lead firmware crash.
ieee80211_set_disassoc() have logic of ieee80211_flush_queues() after
it send_deauth_disassoc() to ath11k, its purpose is make sure the
deauth was actually sent, so it need to change ath11k to match the
purpose of mac80211.
To address these issue wait for tx mgmt as well as tx data packets.
dmesg log of connect/disconnect to AP:
[ 307.522226] wls1: authenticate with 62:66:e4:e9:6a:a9
[ 307.586565] wls1: send auth to 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.586581] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.586922] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.590179] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.590181] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.598699] wls1: authenticated
[ 307.599483] wls1: associate with 62:66:e4:e9:6a:a9 (try 1/3)
[ 307.599506] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 307.599519] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 307.603059] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 307.603063] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 307.637105] wls1: associated
[ 317.365239] wls1: deauthenticating from 62:66:e4:e9:6a:a9 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 317.368104] ath11k_pci 0000:05:00.0: mac tx mgmt frame, buf id 0
[ 317.372622] ath11k_pci 0000:05:00.0: mac tx mgmt frame, vdev_id 0
[ 317.378320] ath11k_pci 0000:05:00.0: wmi mgmt tx comp pending 0 desc id 0
[ 317.378330] ath11k_pci 0000:05:00.0: mgmt tx compl ev pdev_id 2, desc_id 0, status 0
[ 317.378359] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421066] ath11k_pci 0000:05:00.0: mac mgmt tx flush mgmt pending 0
[ 317.421427] ath11k_pci 0000:05:00.0: mac remove interface (vdev 0)
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211202063705.14321-1-quic_wgong@quicinc.com
Use 'bitmap_zalloc()' to simplify code, improve the semantic and avoid some
open-coded arithmetic in allocator arguments.
Note, that this 'bitmap_zalloc()' divides by BITS_PER_LONG the amount of
memory allocated.
The 'roundup()' used to computed the number of needed long should have
been a DIV_ROUND_UP.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Use 'bitmap_zero()' to avoid hand writing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1fe18fb73f71d855043c40c83865ad539f326478.1638396221.git.christophe.jaillet@wanadoo.fr
Kernel test robot reported:drivers/net/wireless/ath/wcn36xx/smd.c:943:33:
sparse: sparse: cast truncates bits from constant value (780 becomes 80)
The 'channels' field is not a simple u8 array but an array of
channel_params. Using sizeof for retrieving the max number of
channels is then wrong.
In practice, it was not an issue, because the sizeof returned
value is 780, which is truncated in min_t (u8) to 80, which is
the value we expect...
Fix that properly using ARRAY_SIZE instead of sizeof.
Fixes: d707f812bb ("wcn36xx: Channel list update before hardware scan")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638435732-14657-1-git-send-email-loic.poulain@linaro.org
Add handler for WMI_11D_NEW_COUNTRY_EVENTID, WMI_11D_SCAN_START_CMDID,
WMI_11D_SCAN_STOP_CMDID.
After vdev create for STATION, send WMI_11D_SCAN_START_CMDID to firmware
and wait firmware complete it, the scan from mac80211 also need to wait
the 11d scan finished, and send WMI_11D_SCAN_STOP_CMDID to firmware
before vdev delete for STATION.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01230-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-4-quic_wgong@quicinc.com
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware which
is used for QCA6390 and WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211201071745.17746-3-quic_wgong@quicinc.com
Using the SET_RUNTIME_PM_OPS() macro causes a warning about the
referenced functions when they are marked static but not __maybe_unused:
drivers/gpu/drm/omapdrm/dss/dss.c:1572:12: error: unused function 'dss_runtime_suspend' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dss.c:1584:12: error: unused function 'dss_runtime_resume' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dispc.c:4845:12: error: unused function 'dispc_runtime_suspend' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dispc.c:4860:12: error: unused function 'dispc_runtime_resume' [-Werror,-Wunused-function]
Fixes: b92f7ea556 ("drm/omap: dss: Make use of the helper macro SET_RUNTIME_PM_OPS()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211205131612.3192652-1-arnd@kernel.org
If the drm_plane has a source width that's greater than the max width
supported by a single hw overlay, then we assign a 'r_overlay' to it in
omap_plane_atomic_check().
Both overlays should have the capabilities required to handle the source
framebuffer. The only parameters that vary between the left and right
hwoverlays are the src_w, crtc_w, src_x and crtc_x as we just even chop
the fb into left and right halves.
We also take care of not creating odd width size when dealing with YUV
formats.
Since both halves need to be 'appear' side by side the zpos is
recalculated when dealing with dual overlay cases so that the other
planes zpos is consistent.
Depending on user space usage it is possible that on occasion the number
of requested planes exceeds the numbers of overlays required to display
them. In that case a failure would be returned for the plane that cannot
be handled at that time. It is up to user space to make sure the H/W
resource are not over-subscribed.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-10-narmstrong@baylibre.com
Now that we added specific item to our subclassed drm_plane_state
we can add omap_plane_atomic_print_state() helper to dump out our own
driver specific plane state.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-9-narmstrong@baylibre.com
(re)assign the hw overlays to planes based on required caps, and to
handle situations where we could not modify an in-use plane.
This means all planes advertise the superset of formats and properties.
Userspace must (as always) use atomic TEST_ONLY step for atomic updates,
as not all planes may be available for use on every frame.
The mapping of hwoverlays to plane is stored in omap_global_state, so
that state updates are atomically committed in the same way that
plane/etc state updates are managed. This is needed because the
omap_plane_state keeps a pointer to the hwoverlay, and we don't want
global state to become out of sync with the plane state if an atomic
update fails, we hit deadlock/ backoff scenario, etc. The use of
global_state_lock keeps multiple parallel updates which both re-assign
hwoverlays properly serialized.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-8-narmstrong@baylibre.com
Global shared resources (like hw overlays) for omapdrm are implemented
as a part of atomic state using the drm_private_obj infrastructure
available in the atomic core.
omap_global_state is introduced as a drm atomic private object. The two
funcs omap_get_global_state() and omap_get_existing_global_state() are
the two variants that will be used to access omap_global_state.
drm_mode_config_init() needs to be called earlier because it
creates/initializes the private_obj link list maintained by the atomic
framework. The private_obj link list has to exist prior to calling
drm_atomic_private_obj_init(). Similarly the cleanup handler are
reordered appropriately.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-7-narmstrong@baylibre.com
In preparation to add omap plane state specific extensions we need to
subclass drm_plane_state and add the relevant helpers.
The addition of specific extension will be done separately.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-6-narmstrong@baylibre.com
Split out the hardware overlay specifics from omap_plane.
To start, the hw overlays are statically assigned to planes.
The goal is to eventually assign hw overlays dynamically to planes
during plane->atomic_check() based on requested caps (scaling, YUV,
etc). And then perform hw overlay re-assignment if required.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-5-narmstrong@baylibre.com
In order to be able to dynamically assign overlays to planes we need to
be able to asses the overlay capabilities.
Add a helper function to be able to retrieve the supported capabilities
of an overlay.
And export the function to check if a fourcc is supported on a given
overlay.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-4-narmstrong@baylibre.com
We currently assume that an overlay has the same maximum width and
maximum height as the overlay manager. This assumption is incorrect. On
some variants the overlay manager maximum width is twice the maximum
width that the overlay can handle. We need to add the appropriate data
per variant as well as export a helper function to retrieve the data so
check can be made dynamically in omap_plane_atomic_check().
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-3-narmstrong@baylibre.com
Call drm_atomic_helper_check_plane_state() from the plane
atomic_check() callback in order to add plane state sanity
checking.
It will permit filtering out totally bad scaling factors, even
if the real check are done later in the atomic commit.
Calling drm_atomic_helper_check_plane_state() also sets
plane_state->visible which will be useful when dynamically
assigning hw overlays to planes.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117141928.771082-2-narmstrong@baylibre.com
Memory of BOs backed by TILER is not contiguous, but omap_gem_map_dma_buf()
exports it like it is. This leads to (possibly) invalid memory accesses if
another device imports such a BO.
Fix that by providing sg that correctly describes TILER memory layout.
Align TILER allocations to page, so importer to be able to correctly set
its MMU if have one. Set export size accounting for the alignment. Also,
make sure to destroy sg on unpin, as it is no longer valid.
Tested on Motorola Droid4 by using GPU (sgx540) to render.
Suggested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1637309180-31032-1-git-send-email-ivo.g.dimitrov.75@gmail.com
Fix typo which will cause fpe and privilege exception error.
Signed-off-by: Kelly Devilliv <kelly.devilliv@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Alexandra Winter says:
====================
s390/net: updates 2021-12-06
This brings some maintenance improvements and removes some
unnecessary code checks.
====================
Link: https://lore.kernel.org/r/20211207090452.1155688-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If qeth_check_outbound_queue() finds a partially filled TX buffer on
the queue and flushes it, then the queue _must_ have been in packing
mode.
Remove the redundant check when updating the relevant statistics.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid a conditional branch for L2 devices when selecting the TX queue,
and have shared logic for OSA devices.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qeth_l2_detect_dev2br_support() will only set brport_hw_features for IQD
devices. So qeth_l2_bridge_getlink() and qeth_l2_bridge_setlink() will
always return -EOPNOTSUPP on OSA devices. Just don't offer these
callbacks instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Splitting up the netdev_ops allows for fine-tuning some of the ndo's
in subsequent patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the OSN code is gone, we don't need the second switch statement
in the RX path. And getting rid of its (unreachable) default case is a
nice simplification.
Also don't pass in the full HW header, all we still need is a flag to
indicate whether the skb can use CSO. This we can already obtain during
the first peek at the HW header.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building under -Warray-bounds, the compiler is especially
conservative when faced with casts from a smaller object to a larger
object. While this has found many real bugs, there are some cases that
are currently false positives (like here). With this as one of the last
few instances of the warning in the kernel before -Warray-bounds can be
enabled globally, rearrange the functions so that there is a header-only
version of hvs_send_data(). Silences this warning:
net/vmw_vsock/hyperv_transport.c: In function 'hvs_shutdown_lock_held.constprop':
net/vmw_vsock/hyperv_transport.c:231:32: warning: array subscript 'struct hvs_send_buf[0]' is partly outside array bounds of 'struct vmpipe_proto_header[1]' [-Warray-bounds]
231 | send_buf->hdr.pkt_type = 1;
| ~~~~~~~~~~~~~~~~~~~~~~~^~~
net/vmw_vsock/hyperv_transport.c:465:36: note: while referencing 'hdr'
465 | struct vmpipe_proto_header hdr;
| ^~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20211207063217.2591451-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix following coccicheck warning:
/drivers/net/dsa/ocelot/felix_vsc9959.c:1627:13-20:
WARNING opportunity for kmemdup
/drivers/net/dsa/ocelot/felix_vsc9959.c:1506:16-23:
WARNING opportunity for kmemdup
Signed-off-by: Yihao Han <hanyihao@vivo.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20211207064419.38632-1-hanyihao@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Foster says:
====================
prepare ocelot for external interface control
This patch set is derived from an attempt to include external control
for a VSC751[1234] chip via SPI. That patch set has grown large and is
getting unwieldy for reviewers and the developers... me.
I'm breaking out the changes from that patch set. Some are trivial
net: dsa: ocelot: remove unnecessary pci_bar variables
net: dsa: ocelot: felix: Remove requirement for PCS in felix devices
some are required for SPI
net: dsa: ocelot: felix: add interface for custom regmaps
and some are just to expose code to be shared
net: mscc: ocelot: split register definitions to a separate file
The entirety of this patch set should have essentially no impact on the
system performance.
====================
Link: https://lore.kernel.org/r/20211207170030.1406601-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move these to a separate file will allow them to be shared to other
drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add an interface so that non-mmio regmaps can be used
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Existing felix devices all have an initialized pcs array. Future devices
might not, so running a NULL check on the array before dereferencing it
will allow those future drivers to not crash at this point
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pci_bar variables for the switch and imdio don't make sense for the
generic felix driver. Moving them to felix_vsc9959 to limit scope and
simplify the felix_info struct.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-12-06
This series contains updates to iavf and i40e drivers.
Mitch adds restoration of MSI state during reset for iavf.
Michal fixes checking and reporting of descriptor count changes to
communicate changes and/or issues for iavf.
Karen resolves an issue with failed handling of VF requests while a VF
reset is occurring for i40e.
Mateusz removes clearing of VF requested queue count when configuring
VF ADQ for i40e.
Norbert fixes a NULL pointer dereference that can occur when getting VSI
descriptors for i40e.
====================
Link: https://lore.kernel.org/r/20211206183519.2733180-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
