Since the firmware cmd to setup mac pause params is the same as the
firmware cmd to pfc pause params, this patch unifies the pause params
setup function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max delat_t should be the full_bucket/rate instead of the full_bucket.
Also report EINVAL if the rate is zero.
Fixes: 96fbc13d7e ("openvswitch: Add meter infrastructure")
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: zhangliping <zhangliping02@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
# ip link add link ens1f0 mv0 type macvlan
RTNETLINK answers: Operation not permitted
Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm. When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.
The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.
This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
selftests: forwarding: Tweaks and a new test
First patch adds a new test for VLAN-unaware bridges.
Next two patches make the tests fail in case they are missing interfaces
or dependencies.
Last patch allows one to create the veth interfaces even without the
optional configuration file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some users want to be able to run the tests without a configuration file
which is useful when one needs to test both virtual and physical
interfaces on the same machine.
Move the defines that set the type of interface to create and whether to
create it away from the optional configuration file to the library like
the rest of the defines.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 gives a false sense of success when the required modules did
not even manage to be initialized and register the required net devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already return an error when some dependencies (e.g., 'jq') are
missing so lets be consistent and do that for all.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the VLAN-aware bridge test, test the VLAN-unaware bridge and
make sure that ping, FDB learning and flooding work as expected.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's found that the final phase set by driver doesn't match that of
the output from clk_summary:
dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 346
mmc0: new ultra high speed SDR104 SDIO card at address 0001
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 0
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Fixes: 9e4d04adeb ("clk: add clk_core_set_phase_nolock function")
Cc: Stable <stable@vger.kernel.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Currently MHL chip must be turned on permanently to detect MHL cable. It
duplicates micro-USB controller's (MUIC) functionality and consumes
unnecessary power. Lets use extcon attached to MUIC to enable MHL chip
only if it detects MHL cable.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Fix the pointer to struct scp_subdomian not being moved forward
when each sub-domain is expected to be iteratively added through
pm_genpd_add_subdomain call.
Cc: stable@vger.kernel.org
Fixes: 53fddb1a66 ("soc: mediatek: reduce code duplication of scpsys_probe across all SoCs")
Reported-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add SCPSYS power domain driver for MT7623A SoC. The MT7623A's power
domains are the subset of MT7623 SoC's ones. As MT7623 SoC has full
features whereas MT7623A is being designed just for router applications.
Thus, MT7623A doesn't include those power domains multimedia function
belongs to. In order to avoid certain errors undoubtedly happening at
registering those power domains on MT7623A SoC using the existing MT7623
SCPSYS driver, it's required to define another setup specifically for
MT7623A SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
use a meaningful definition for bus_prot_mask instead of just hardcoded
for it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add relevant header files required for dt-bindings of SCPSYS power domain
control for subsystems found on MT7623A SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[mb: clean-up commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
document the binding for enabling SCPSYS on MediaTek MT7623 and MT7623A
SoC. Where MT7623 SoC has the same definition about power domains with
MT2701, so it's fine to using MT2701 ones as MT7623's fallback.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
RCC manages clock for debug and trace.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Two micro-controller clock output (MCO) pins are available:
MCO1 and MCO2.
For each output, it is possible to select a clock source.
The selected clock can be divided thanks to configurable
prescaler.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each peripheral requires a bus interface clock.
Some peripherals need also a dedicated clock for their communication
interface, this clock is generally asynchronous with respect to the bus
interface clock (peripheral clock), and is named kernel clock.
For each IP, Peripheral clock and Kernel are generally gating with same
gate. Also, Kernel clocks can share a same multiplexer.
This patch introduces a mechanism to manage a gate with several
clocks and to manage a shared multiplexer (mgate and mmux).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds Kernel timers.
This patch adds timers kernel clock.
Timers are gather into two groups corresponding to the APB bus
they are attached to.
Each group has its own prescaler, managed in this patch.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC handles three sub-system clocks: ck_mpuss, ck_axiss
and ck_mcuss.
This patch adds also some MUX system and several prescalers.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each PLL has 3 outputs with post-dividers.
pll1_p is dedicated for Cortex-A7
pll1_q is not connected
pll1_r is not connected
pll2_p is dedicated for AXI
pll2_q is dedicated for GPU
pll2_r is dedicated for DDR
pll3_p is dedicated for mcu
pll3_q is for Peripheral Kernel Clock
pll3_r is for Peripheral Kernel Clock
pll4_p is for Peripheral Kernel Clock
pll4_q is for Peripheral Kernel Clock
pll4_r is for Peripheral Kernel Clock
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
STMP32MP1 has 4 PLLs.
PLL supports integer and fractional mode.
Each PLL has 3 output dividers (p, q, r)
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds source clocks for PLLs
This patch also introduces MUX clock API.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MP1 Gate is a gate with a set and a clear register.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC block is responsible of the management of the clock and reset
generation for the complete circuit.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Pull x86/pti updates from Thomas Gleixner:
"Yet another pile of melted spectrum related updates:
- Drop native vsyscall support finally as it causes more trouble than
benefit.
- Make microcode loading more robust. There were a few issues
especially related to late loading which are now surfacing because
late loading of the IB* microcodes addressing spectre issues has
become more widely used.
- Simplify and robustify the syscall handling in the entry code
- Prevent kprobes on the entry trampoline code which lead to kernel
crashes when the probe hits before CR3 is updated
- Don't check microcode versions when running on hypervisors as they
are considered as lying anyway.
- Fix the 32bit objtool build and a coment typo"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Fix kernel crash when probing .entry_trampoline code
x86/pti: Fix a comment typo
x86/microcode: Synchronize late microcode loading
x86/microcode: Request microcode on the BSP
x86/microcode/intel: Look into the patch cache first
x86/microcode: Do not upload microcode if CPUs are offline
x86/microcode/intel: Writeback and invalidate caches before updating microcode
x86/microcode/intel: Check microcode revision before updating sibling threads
x86/microcode: Get rid of struct apply_microcode_ctx
x86/spectre_v2: Don't check microcode versions when running under hypervisors
x86/vsyscall/64: Drop "native" vsyscalls
x86/entry/64/compat: Save one instruction in entry_INT80_compat()
x86/entry: Do not special-case clone(2) in compat entry
x86/syscalls: Use COMPAT_SYSCALL_DEFINEx() macros for x86-only compat syscalls
x86/syscalls: Use proper syscall definition for sys_ioperm()
x86/entry: Remove stale syscall prototype
x86/syscalls/32: Simplify $entry == $compat entries
objtool: Fix 32-bit build
Pull timer fix from Thomas Gleixner:
"Just a single fix which adds a missing Kconfig dependency to avoid
unmet dependency warnings"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/atmel-st: Add 'depends on HAS_IOMEM' to fix unmet dependency
Pull RAS fixes from Thomas Gleixner:
"Two small fixes for RAS/MCE:
- Serialize sysfs changes to avoid concurrent modificaiton of
underlying data
- Add microcode revision to Machine Check records. This should have
been there forever, but now with the broken microcode versions in
the wild it has become important"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE: Serialize sysfs changes
x86/MCE: Save microcode revision in machine check records
Pull perf updates from Thomas Gleixner:
"Another set of perf updates:
- Fix a Skylake Uncore event format declaration
- Prevent perf pipe mode from crahsing which was caused by a missing
buffer allocation
- Make the perf top popup message which tells the user that it uses
fallback mode on older kernels a debug message.
- Make perf context rescheduling work correcctly
- Robustify the jump error drawing in perf browser mode so it does
not try to create references to NULL initialized offset entries
- Make trigger_on() robust so it does not enable the trigger before
everything is set up correctly to handle it
- Make perf auxtrace respect the --no-itrace option so it does not
try to queue AUX data for decoding.
- Prevent having different number of field separators in CVS output
lines when a counter is not supported.
- Make the perf kallsyms man page usage behave like it does for all
other perf commands.
- Synchronize the kernel headers"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix ctx_event_type in ctx_resched()
perf tools: Fix trigger class trigger_on()
perf auxtrace: Prevent decoding when --no-itrace
perf stat: Fix CVS output format for non-supported counters
tools headers: Sync x86's cpufeatures.h
tools headers: Sync copy of kvm UAPI headers
perf record: Fix crash in pipe mode
perf annotate browser: Be more robust when drawing jump arrows
perf top: Fix annoying fallback message on older kernels
perf kallsyms: Fix the usage on the man page
perf/x86/intel/uncore: Fix Skylake UPI event format
Pull locking fix from Thomas Gleixner:
"rt_mutex_futex_unlock() grew a new irq-off call site, but the function
assumes that its always called from irq enabled context.
Use (un)lock_irqsafe() to handle the new call site correctly"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Make rt_mutex_futex_unlock() safe for irq-off callsites
add mmc device nodes and proper setup for used pins
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Jimin Wang <jimin.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
ebt_among is special, it has a dynamic match size and is exempt
from the central size checks.
commit c4585a2823 ("bridge: ebt_among: add missing match size checks")
added validation for pool size, but missed fact that the macros
ebt_among_wh_src/dst can already return out-of-bound result because
they do not check value of wh_src/dst_ofs (an offset) vs. the size
of the match that userspace gave to us.
v2:
check that offset has correct alignment.
Paolo Abeni points out that we should also check that src/dst
wormhash arrays do not overlap, and src + length lines up with
start of dst (or vice versa).
v3: compact wormhash_sizes_valid() part
NB: Fixes tag is intentionally wrong, this bug exists from day
one when match was added for 2.6 kernel. Tag is there so stable
maintainers will notice this one too.
Tested with same rules from the earlier patch.
Fixes: c4585a2823 ("bridge: ebt_among: add missing match size checks")
Reported-by: <syzbot+bdabab6f1983a03fc009@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
recent and hashlimit both create /proc files, but only check that
name is 0 terminated.
This can trigger WARN() from procfs when name is "" or "/".
Add helper for this and then use it for both.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: <syzbot+0502b00edac2a0680b61@syzkaller.appspotmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.
Fixes: b718121685 ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Two small fixes are for this cycle:
- fix max_chunk_size for rcar-dmac for R-Car Gen3
- fix clock resource of mv_xor_v2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RhQT
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.16-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Two small fixes are for this cycle:
- fix max_chunk_size for rcar-dmac for R-Car Gen3
- fix clock resource of mv_xor_v2"
* tag 'dmaengine-fix-4.16-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: mv_xor_v2: Fix clock resource by adding a register clock
dmaengine: rcar-dmac: fix max_chunk_size for R-Car Gen3
Renesas driver, and fixes wakeup from external stuff.
-----BEGIN PGP SIGNATURE-----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=8lyD
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"This is a single GPIO fix for the v4.16 series affecting the Renesas
driver, and fixes wakeup from external stuff"
* tag 'gpio-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: rcar: Use wakeup_path i.s.o. explicit clock handling
This patch adds SATA support fot MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch adds PCIe support for MT7622.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: fix type in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add ethernet device nodes which enable GMAC1 with SGMII interface
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add nodes for NOR flash, parallel Nand flash with error correction code
support.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: RogerCC Lin <rogercc.lin@mediatek.com>
Cc: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>