[Why]
If two monitors with TMDS signals were timing synced and one was
disconnected, the stream would go out of sync too early due to
the PLL turning off and the system could hang
[How]
On link disable output, change PHY FSM transition from TX_EN-to-PHY_OFF
to TX_EN-to-PLL_ON for TMDS
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the ptr handle to amdgpu_ip_block ptr in all
the functions affected.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are more IPS modes other than DMUB_IPS_ENABLE that enables IPS. We
need to enable the hotplug detect idle workqueue for those modes as
well.
[How]
Modify the if condition to initialize the workqueue in all IPS modes
except for DMUB_IPS_DISABLE_ALL.
Fixes: 65444581a4 ("drm/amd/display: Determine IPS mode by ASIC and PMFW versions")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current state should be used when waiting for DET update
instead of new context.
For any streams decreasing in DET, pipes used in the current state
should be checked since those pipes need to free their DET before
DET can be reallocated.
[How]
Pass in current_state instead of context.
Use pipe from current_state instead of context. This assumes that
pipe in the current_state is an OTG_MASTER pipe if the pipe in the context is an OTG_MASTER pipe.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Some eDP panels suffer from flicking when HDR is enabled in KDE. This
quirk works around it by skipping VSC that is incompatible with eDP
panels.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3151
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where an MPO plane is being dragged around partially off-screen,
it is possible to get a flip where the only scaling parameters to change
are the clip rect size and position. Currently, clip rect size changes
are considered medium updates, which can result in the clip rect being used
for HW programming being larger than the clip rect that was used for the
last DML validation. This can lead to mismatches in different parts of the
pipe and can result in a p-state hang.
[How]
- consider clip rect size changes scaling changes, therefore full updates
- refactor get_scaling_info_update_type for clarity
- remove clip_size_change update flag
Clip rect size changes were previously demoted from full updates as an
optimization when the MPO + ODM policy changed to always pre-allocate MPO
pipes, but it created the issue described above. Personally testing this
use case, the performance feels fine with full update spam, and we expect
this is a fairly infrequent use case. If the performance needs to be
optimized in the future, consider reworking the entire update type logic
to run a DML pass and determine the update type based on what DML says
will actually change.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain transitions from HW to SW cursor can be missed, which will
result in black visual confirm instead of expected blue/red. Need to add
handling for cursor visual confirm to dc_update_visual_confirm_color.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Videos using YUV420 format may result in high power being used.
Disabling MPO may result in lower power usage.
Update interface that can be used to check power profile of a dc_state.
[How]
Allow pstate switching in VBlank as last entry in strategy candidates.
Add helper functions that can be used to determine power level:
-get power profile after a dc_state has undergone full validation
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The "dpp35_dppclk_control" routine is incorrectly disabling the register clock gater
when the DPP is enabled.
The "DISPCLK_R_GATE_DISABLE" should never be set to 1 in the normal operating mode.
This will disable the clock gater and the DPPCLK register clock branch will always be running.
As a consequence, the dynamic power will be higher than expected.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
set dispclk to 0 cause stability issue.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently the absence of UHBR cable ID caps from USB-C PD does not block UHBR
rates. In situations where DPCD reports valid UHBR capability but USB-C PD
does not, such as using a USB-C to DP1.4 dongle connected to a native DP2.1
cable, link loss and lightup failures can be seen as a result.
Additionally, in edge cases where a platform supports cable ID but DMUB
doesn't correctly return cable ID caps, driver currently also allows UHBR.
[HOW]
Block UHBR rates over DP alt mode if cable id indicates no UHBR support.
Additionally, block UHBR rates if a cable ID supported platform receives no
reply from a DMUB cable id query.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current pipe unlock order set within dcn401_interdependent_update_lock.
Separate the logic from the functionality to allow for unit testing
and make it easier to debug.
[How]
Add a flag to indicate if a pipe unlock order should be set.
Create function to determine unlock order.
Indicate which pipes should be unlocked first using
array stored in dc scratch memory.
Pipes indicated in array can be unlocked in any order.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
cm2_params is used to set update_flags.
It's value is not intended to be modified.
[WHAT]
Change the declaration of cm2_params to be a constant variable
Reviewed-by: Tao Huang <tao.huang@amd.com>
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Signed-off-by: Shunlu Zhang <Shunlu.Zhang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Triple buffer enablement currently does not work properly
[HOW]
Allow triple buffer enablement to happen properly on
fast updates
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Sung Lee <sunglee@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A stream without dsc_aux should not be eliminated from
the dsc determination. Whether it needs a dsc recompute depends on
whether its mode has changed or not. Eliminating such a no-dsc stream
from the dsc determination policy will end up with inconsistencies
in the new dc_state when compared to the current dc_state,
triggering a dsc recompute that should not have happened.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Turning off OTG before DIG is on and backlight is on, might cause:
DIG FIFO underflow.
EDP output unexpected video data. That might violate EDP spec.
EDP spec requires black light should be off before validate
video data is turned off.
Currently garbage issue only occurs in one type of EDP to MIPI converter.
[How]
Add monitor patch to call blank_stream() before disable_crtc().
That will be no impact for current sequence.
If there are more types of EDP panels meeting this issue later,
we might remove this monitor patch and fix the current sequence.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Existing last step of dsc policy is to restore pbn value under minimum compression
when try to greedily disable dsc for a stream failed to fit in MST bw.
Optimized dsc params result from optimization step is not necessarily the minimum compression,
therefore it is not correct to restore the pbn under minimum compression rate.
Restore the pbn under minimum compression instead of the value from optimized pbn could result
in the dsc params not correct at the modeset where atomic_check failed due to not
enough bw. One or more monitors connected could not light up in such case.
Restore the optimized pbn value, instead of using the pbn value under minimum
compression.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
When integer scaling is enabled, set taps to 1 and disable adaptive
scaler and sharpener.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Mismatch in DCN35 DML2 cause bw validation failed to acquire unexpected DPP pipe to cause
grey screen and system hang. Remove EnhancedPrefetchScheduleAccelerationFinal value override
to match HW spec.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add partition config nodes in sysfs to get resource instance details for
a particular partition mode. A resource could be anything like an xcc,
vcn decoder, system dma units etc.
Details of various resource instances are available under
/sys/bus/pci/devices/.../compute_partition_config/
Select a partition configuration:
/sys/bus/pci/devices/.../compute_partition_config/xcp_config
Number of instances of a resource:
/sys/bus/pci/devices/.../compute_partition_config/<rsrc_name>/num_inst
Total partitions sharing the resource:
/sys/bus/pci/devices/.../compute_partition_config/<rsrc_name>/num_shared
v2: Update node name as per spec
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the ptr handle to amdgpu_ip_block ptr in all
the functions.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Extract the resume sequence from sdma_v5_0_gfx_resume for
starting/restarting an individual instance.
Signed-off-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct file *f is unused in queue creation, remove it.
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes the elida-kd35t133 panel to use multi style functions for
improved error handling.
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Tejas Vipin <tejasvipin76@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240925080003.1250448-1-tejasvipin76@gmail.com
This reverts commit 8d20a066fa.
It's causing a failure in the abm_gradual igt test.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use struct_size() to calculate the number of bytes to allocate for a
new message.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Add the __counted_by_le compiler attribute to the flexible array member
Chunks to improve access bounds-checking via CONFIG_UBSAN_BOUNDS and
CONFIG_FORTIFY_SOURCE.
Change the data type of the flexible array member Chunks from __u8[] to
struct srv_copychunk[] for ChunkCount to match the number of elements in
the Chunks array. (With __u8[], each srv_copychunk would occupy 24 array
entries and the __counted_by compiler attribute wouldn't be applicable.)
Use struct_size() to calculate the size of the copychunk_ioctl_req.
Read Chunks[0] after checking that ChunkCount is not 0.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Use struct_size() to calculate the output buffer length.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The bpf_redirect_info is shared between the SKB and XDP redirect paths,
and the two paths use the same numeric flag values in the ri->flags
field (specifically, BPF_F_BROADCAST == BPF_F_NEXTHOP). This means that
if skb bpf_redirect_neigh() is used with a non-NULL params argument and,
subsequently, an XDP redirect is performed using the same
bpf_redirect_info struct, the XDP path will get confused and end up
crashing, which syzbot managed to trigger.
With the stack-allocated bpf_redirect_info, the structure is no longer
shared between the SKB and XDP paths, so the crash doesn't happen
anymore. However, different code paths using identically-numbered flag
values in the same struct field still seems like a bit of a mess, so
this patch cleans that up by moving the flag definitions together and
redefining the three flags in BPF_F_REDIRECT_INTERNAL to not overlap
with the flags used for XDP. It also adds a BUILD_BUG_ON() check to make
sure the overlap is not re-introduced by mistake.
Fixes: e624d4ed4a ("xdp: Extend xdp_redirect_map with broadcast support")
Reported-by: syzbot+cca39e6e84a367a7e6f6@syzkaller.appspotmail.com
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Closes: https://syzkaller.appspot.com/bug?extid=cca39e6e84a367a7e6f6
Link: https://lore.kernel.org/bpf/20240920125625.59465-1-toke@redhat.com
Switch to device_for_each_child_node_scoped() to simplify the code by
removing the need for a call to fwnode_handle_put() in the error path.
This also prevents possible memory leaks if new error paths are added
without the required call to fwnode_handle_put().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240928-gpio_device_for_each_child_node_scoped-v1-2-c20eff315f4f@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Switch to device_for_each_child_node_scoped() to simplify the code by
removing the need for a call to fwnode_handle_put() in the error path.
This also prevents possible memory leaks if new error paths are added
without the required call to fwnode_handle_put().
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240928-gpio_device_for_each_child_node_scoped-v1-1-c20eff315f4f@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Dell All In One (AIO) models released after 2017 may use a backlight
controller board connected to an UART.
In DSDT this uart port will be defined as:
Name (_HID, "DELL0501")
Name (_CID, EisaId ("PNP0501")
The Dell OptiPlex 5480 AIO has an ACPI device for one of its UARTs with
the above _HID + _CID. Loading the dell-uart-backlight driver fails with
the following errors:
[ 18.261353] dell_uart_backlight serial0-0: Timed out waiting for response.
[ 18.261356] dell_uart_backlight serial0-0: error -ETIMEDOUT: getting firmware version
[ 18.261359] dell_uart_backlight serial0-0: probe with driver dell_uart_backlight failed with error -110
Indicating that there is no backlight controller board attached to
the UART, while the GPU's native backlight control method does work.
Add a quirk to use the GPU's native backlight control method on this model.
Fixes: cd8e468efb ("ACPI: video: Add Dell UART backlight controller detection")
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20240918153849.37221-1-hdegoede@redhat.com
[ rjw: Changelog edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the parse_perf_domain function, if the call to
of_parse_phandle_with_args returns an error, then the reference to the
CPU device node that was acquired at the start of the function would not
be properly decremented.
Address this by declaring the variable with the __free(device_node)
cleanup attribute.
Signed-off-by: Miquel Sabaté Solà <mikisabate@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://patch.msgid.link/20240917134246.584026-1-mikisabate@gmail.com
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
notify_hwp_interrupt() is called via sysvec_thermal() ->
smp_thermal_vector() -> intel_thermal_interrupt() in hard irq context.
For this reason it must not use a simple spin_lock that sleeps with
PREEMPT_RT enabled. So convert it to a raw spinlock.
Reported-by: xiao sheng wen <atzlinux@sina.com>
Link: https://bugs.debian.org/1076483
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: xiao sheng wen <atzlinux@sina.com>
Link: https://patch.msgid.link/20240919081121.10784-2-ukleinek@debian.org
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Drop unused auxbus/auxdev support from the PTP code due to
move to the ice_adapter.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use struct ice_adapter to hold shared PTP data and control PTP
related actions instead of auxbus. This allows significant code
simplification and faster access to the container fields used in
the PTP support code.
Move the PTP port list to the ice_adapter container to simplify
the code and avoid race conditions which could occur due to the
synchronous nature of the initialization/access and
certain memory saving can be achieved by moving PTP data into
the ice_adapter itself.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Address E825C devices by PCI ID since dual IP core configurations
need 1 ice_adapter for both devices.
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add ice_get_ctrl_ptp() wrapper to simplify the PTP support code
in the functions that do not use ctrl_pf directly.
Add the control PF pointer to struct ice_adapter
Rearrange fields in struct ice_adapter
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement configuring 1PPS signal output from CGU. Use maximal amplitude
because Linux PTP pin API does not have any way for user to set signal
level.
This change is necessary for E825C products to properly output any
signal from 1PPS pin.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Sergey Temerkhanov <sergey.temerkhanov@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
PTP pins assignment and their related SDPs (Software Definable Pins) are
currently hardcoded.
Fix that by reading NVM section instead on products supporting this,
which are E810 products.
If SDP section is not defined in NVM, the driver continues to use the
hardcoded table.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When setting a new supported function for a pin on E810, disable other
enabled pin that shares the same GPIO.
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
