[ Upstream commit 219be4711a ]
This will help on validating the userq input args, and
rejecting for the invalid userq request at the IOCTLs
first place.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a33be64b98 ]
This patch fixes to support different block size.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 955f3bc4af ]
On DGFX, during init_post_hwconfig() step, we are reinitializing
CTB BO in VRAM and we have to replace cleanup action to disable CT
communication prior to release of underlying BO.
But that introduces some discrepancy between DGFX and iGFX, as for
iGFX we keep previously added disable CT action that would be called
during unwind much later.
To keep the same flow on both types of platforms, always replace old
cleanup action and register new one.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Satyanarayana K V P <satyanarayana.k.v.p@intel.com>
Link: https://lore.kernel.org/r/20250908102053.539-2-michal.wajdeczko@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0e7f358e7 ]
Instead of writing the first byte of the infoframe (and hoping that the
rest is default / zeroes), hook Audio InfoFrame support into the
write_infoframe / clear_infoframes callbacks and use
drm_atomic_helper_connector_hdmi_update_audio_infoframe() to write the
frame.
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250903-adv7511-audio-infoframe-v1-2-05b24459b9a4@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce63fbdf84 ]
This is the CSI PHY version found in QCS2290/QCM2290 SoCs.
The table is extracted from downstream camera driver.
Signed-off-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfbd5aa534 ]
The OmniVision OG01A1B image sensor is a monochrome sensor, it supports
8-bit and 10-bit RAW output formats only.
That said the planar greyscale Y8/Y10 media formats are more appropriate
for the sensor instead of the originally and arbitrary selected SGRBG one,
since there is no red, green or blue color components.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7df6f339a ]
The datasheet of ov08x40 doesn't match the hardware behavior.
0x3821[2] == 1 is the original state and 0 the horizontal flip enabled.
Signed-off-by: Hao Yao <hao.yao@intel.com>
Reviewed-by: Hans de Goede <hansg@kernel.org>
Tested-by: Hans de Goede <hansg@kernel.org> # ThinkPad X1 Carbon Gen 12 & Gen 13
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5318e6e1c ]
Add ASUS to the list of OEMs that are allowed to use
the PPAG and TAS feature.
Signed-off-by: Nidhish A N <nidhish.a.n@intel.com>
Reviewed-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250909061931.499af6568e89.Iafb2cb1c83ff82712c0e9d5529f76bc226ed12dd@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ffc73cdb8 ]
Add USB ID 2001:332a for D-Link AX9U rev. A1 which is a RTL8851BU-based
Wi-Fi adapter.
Only managed mode and AP mode are tested and it works in both.
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250902035755.1969530-1-zenmchen@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5f6bd3ee3 ]
Currently, the test allocates BAR sizes according to fixed table bar_size.
This does not work with controllers which have fixed size BARs that are
smaller than the requested BAR size. One such controller is Renesas R-Car
V4H PCIe controller, which has BAR4 size limited to 256 bytes, which is
much less than one of the BAR size, 131072 currently requested by this
test. A lot of controllers drivers in-tree have fixed size BARs, and they
do work perfectly fine, but it is only because their fixed size is larger
than the size requested by pci-epf-test.c
Adjust the test such that in case a fixed size BAR is detected, the fixed
BAR size is used, as that is the only possible option.
This helps with test failures reported as follows:
pci_epf_test pci_epf_test.0: requested BAR size is larger than fixed size
pci_epf_test pci_epf_test.0: Failed to allocate space for BAR4
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250905184240.144431-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27bc5eaf00 ]
Recent changes to make netlink socket memory accounting must
have broken the implicit assumption of the netlink-dump test
that we can fit exactly 64 dumps into the socket. Handle the
failure mode properly, and increase the dump count to 80
to make sure we still run into the error condition if
the default buffer size increases in the future.
Link: https://patch.msgid.link/20250906211351.3192412-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd74a86bc7 ]
Add the missing linking of NAPIs to netdev queues when enabling
interrupt vectors in order to support NAPI configuration and
interfaces requiring get_rx_queue()->napi to be set (like XSk
busy polling).
As currently, idpf_vport_{start,stop}() is called from several flows
with inconsistent RTNL locking, we need to synchronize them to avoid
runtime assertions. Notably:
* idpf_{open,stop}() -- regular NDOs, RTNL is always taken;
* idpf_initiate_soft_reset() -- usually called under RTNL;
* idpf_init_task -- called from the init work, needs RTNL;
* idpf_vport_dealloc -- called without RTNL taken, needs it.
Expand common idpf_vport_{start,stop}() to take an additional bool
telling whether we need to manually take the RTNL lock.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> # helper
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Ramu R <ramu.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f195421318 ]
CP_ALWAYS_ON counter falls under GX domain which is collapsed during
IFPC. So switch to GMU_ALWAYS_ON counter for any CPU reads since it is
not impacted by IFPC. Both counters are clocked by same xo clock source.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673373/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a27d774045 ]
There are some special registers which are accessible even when GX power
domain is collapsed during an IFPC sleep. Accessing these registers
wakes up GPU from power collapse and allow programming these registers
without additional handshake with GMU. This patch adds support for this
special register write sequence.
Signed-off-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673368/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e28022873c ]
Currently, misc_deregister() uses list_del() to remove the device
from the list. After list_del(), the list pointers are set to
LIST_POISON1 and LIST_POISON2, which may help catch use-after-free bugs,
but does not reset the list head.
If misc_deregister() is called more than once on the same device,
list_empty() will not return true, and list_del() may be called again,
leading to undefined behavior.
Replace list_del() with list_del_init() to reinitialize the list head
after deletion. This makes the code more robust against double
deregistration and allows safe usage of list_empty() on the miscdevice
after deregistration.
[ Note, this seems to keep broken out-of-tree drivers from doing foolish
things. While this does not matter for any in-kernel drivers,
external drivers could use a bit of help to show them they shouldn't
be doing stuff like re-registering misc devices - gregkh ]
Signed-off-by: Xion Wang <xion.wang@mediatek.com>
Link: https://lore.kernel.org/r/20250904063714.28925-2-xion.wang@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10fb1b2fca ]
If two fault IRQs arrive in short succession recovery work will be
queued up twice.
When recovery runs a second time it may end up killing an unrelated
context.
Prevent this by masking off interrupts when triggering recovery.
Signed-off-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Akhil P Oommen <akhilpo@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/670023/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2cc1e60c1 ]
Update Adreno 623's dt-binding to remove smmu_clk which is not required
for this GMU.
Signed-off-by: Jie Zhang <quic_jiezh@quicinc.com>
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/672455/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d6a29a19b ]
Somehow we never noticed this when arm64 became a thing, many years ago.
v2: also fix npages
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/669785/
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b434ed000 ]
Not all FRAM chips have a device ID and implement the corresponding read
command. For such chips this led to the following error on module
loading:
at25 spi2.0: Error: no Cypress FRAM (id 00)
The device ID contains the memory size, so devices without this ID are
supported now by setting the size manually in Devicetree using the
"size" property.
Tested with FM25L16B and "size = <2048>;":
at25 spi2.0: 2 KByte fm25 fram, pagesize 4096
According to Infineon/Cypress datasheets, these FRAMs have a device ID:
FM25V01A
FM25V02A
FM25V05
FM25V10
FM25V20A
FM25VN10
but these do not:
FM25040B
FM25640B
FM25C160B
FM25CL64B
FM25L04B
FM25L16B
FM25W256
So all "FM25V*" FRAMs and only these have a device ID. The letter after
"FM25" (V/C/L/W) only describes the voltage range, though.
Link: https://lore.kernel.org/all/20250401133148.38330-1-m.heidelberg@cab.de/
Signed-off-by: Markus Heidelberg <m.heidelberg@cab.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20250815095839.4219-3-m.heidelberg@cab.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da7e8b3823 ]
In vt_ioctl(), the handler for VT_RESIZE always returns 0, which prevents
users from detecting errors. Add the missing return value so that errors
can be properly reported to users like vt_resizex().
Signed-off-by: Zizhi Wo <wozizhi@huaweicloud.com>
Link: https://lore.kernel.org/r/20250904023955.3892120-1-wozizhi@huaweicloud.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fa89f3a7 ]
Starting with commit f99508074e ("PM: domains: Detach on
device_unbind_cleanup()"), there is no longer a need to call
dev_pm_domain_detach() in the bus remove function. The
device_unbind_cleanup() function now handles this to avoid
invoking devres cleanup handlers while the PM domain is
powered off, which could otherwise lead to failures as
described in the above-mentioned commit.
Drop the explicit dev_pm_domain_detach() call and rely instead
on the flags passed to dev_pm_domain_attach() to power off the
domain.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20250827101747.928265-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc6a5b540c ]
GENI UART driver currently supports only non-DFS (Dynamic Frequency
Scaling) mode for source frequency selection. However, to operate correctly
in DFS mode, the GENI SCLK register must be programmed with the appropriate
DFS index. Failing to do so can result in incorrect frequency selection
Add support for Dynamic Frequency Scaling (DFS) mode in the GENI UART
driver by configuring the GENI_CLK_SEL register with the appropriate DFS
index. This ensures correct frequency selection when operating in DFS mode.
Replace the UART driver-specific logic for clock selection with the GENI
common driver function to obtain the desired frequency and corresponding
clock index. This improves maintainability and consistency across
GENI-based drivers.
Signed-off-by: Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250903063136.3015237-1-viken.dadhaniya@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87c5ff5615 ]
In the __cdnsp_gadget_init() and cdnsp_gadget_exit() functions, the gadget
structure (pdev->gadget) was freed before its endpoints.
The endpoints are linked via the ep_list in the gadget structure.
Freeing the gadget first leaves dangling pointers in the endpoint list.
When the endpoints are subsequently freed, this results in a use-after-free.
Fix:
By separating the usb_del_gadget_udc() operation into distinct "del" and
"put" steps, cdnsp_gadget_free_endpoints() can be executed prior to the
final release of the gadget structure with usb_put_gadget().
A patch similar to bb9c74a5bd14("usb: dwc3: gadget: Free gadget structure
only after freeing endpoints").
Signed-off-by: Chen Yufeng <chenyufeng@iie.ac.cn>
Link: https://lore.kernel.org/r/20250905094842.1232-1-chenyufeng@iie.ac.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed6f727c57 ]
Set the hid req->zero flag of ep0/in_ep to true by default,
then the UDC drivers can transfer a zero length packet at
the end if the hid transfer with size divisible to EPs max
packet size according to the USB 2.0 spec.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/1756204087-26111-1-git-send-email-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f616757dd ]
The "usxgmii" phy-mode that the Felix switch ports support on LS1028A is
not quite USXGMII, it is defined by the USXGMII multiport specification
document as 10G-QXGMII. It uses the same signaling as USXGMII, but it
multiplexes 4 ports over the link, resulting in a maximum speed of 2.5G
per port.
This change is needed in preparation for the lynx-10g SerDes driver on
LS1028A, which will make a more clear distinction between usxgmii
(supported on lane 0) and 10g-qxgmii (supported on lane 1). These
protocols have their configuration in different PCCR registers (PCCRB vs
PCCR9).
Continue parsing and supporting single-port-per-lane USXGMII when found
in the device tree as usual (because it works), but add support for
10G-QXGMII too. Using phy-mode = "10g-qxgmii" will be required when
modifying the device trees to specify a "phys" phandle to the SerDes
lane. The result when the "phys" phandle is present but the phy-mode is
wrong is undefined.
The only PHY driver in known use with this phy-mode, AQR412C, will gain
logic to transition from "usxgmii" to "10g-qxgmii" in a future change.
Prepare the driver by also setting PHY_INTERFACE_MODE_10G_QXGMII in
supported_interfaces when PHY_INTERFACE_MODE_USXGMII is there, to
prevent breakage with existing device trees.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250903130730.2836022-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c0b9ed240 ]
devmem test fails on NIPA. Most likely we get skb(s) with readable
frags (why?) but the failure manifests as an OOM. The OOM happens
because ncdevmem spams the following message:
recvmsg ret=-1
recvmsg: Bad address
As of today, ncdevmem can't deal with various reasons of EFAULT:
- falling back to regular recvmsg for non-devmem skbs
- increasing ctrl_data size (can't happen with ncdevmem's large buffer)
Exit (cleanly) with error when recvmsg returns EFAULT. This should at
least cause the test to cleanup its state.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250904182710.1586473-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f3c044f3 ]
[Why]
There is a `scale` sysfs attribute that can be used to indicate when
non-linear brightness scaling is in use. As Custom brightness curves
work by linear interpolation of points the scale is no longer linear.
[How]
Indicate non-linear scaling when custom brightness curves in use and
linear scaling otherwise.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <superm1@kernel.org>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf32515a70 ]
v1:
Returns different error codes based on the scenario to help the user app understand
the AMDGPU device status when an exception occurs.
v2:
change -NODEV to -EBUSY.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 895b61395e ]
[why&how]
control flag for the wait during pipe update wait for vupdate should
be set if update type is not fast or med to prevent an invalid sleep
operation
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cdfb61b3 ]
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa819e3a7c ]
Some SOCs which are part of the cyan skillfish family
rely on an explicit firmware for IP discovery. Add support
for the gpu_info firmware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f320ed01cf ]
Correct valid_bits and ms_chk_bits of section info field for bad page
threshold exceed CPER to match OOB's behavior.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 376358bb97 ]
Since there are too many variants available for Foxconn T99W696 modem, and
they all share the same configuration, use PCI_ANY_ID as the subsystem
device ID to match each possible SKUs and support all of them.
Signed-off-by: Slark Xiao <slark_xiao@163.com>
[mani: reworded subject/description and dropped the fixes tag]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20250819020013.122162-1-slark_xiao@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecf6508923 ]
These registers exist and at least on the t602x variant the IRQ only
clears when theses are cleared.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Sven Peter <sven@kernel.org>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Link: https://lore.kernel.org/r/20250826-dart-t8110-stream-error-v1-1-e33395112014@jannau.net
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c571019d8 ]
Since SEV or SNP may already be initialized in the previous kernel,
attempting to initialize them again in the kdump kernel can result
in SNP initialization failures, which in turn lead to IOMMU
initialization failures. Moreover, SNP/SEV guests are not run under a
kdump kernel, so there is no need to initialize SEV or SNP during
kdump boot.
Skip SNP and SEV INIT if doing kdump boot.
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/d884eff5f6180d8b8c6698a6168988118cf9cba1.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38e5f33ee3 ]
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU device table register is locked and exclusive to the previous
kernel. Attempts to copy old device table from the previous kernel
fails in kdump kernel as hardware ignores writes to the locked device
table base address register as per AMD IOMMU spec Section 2.12.2.1.
This causes the IOMMU driver (OS) and the hardware to reference
different memory locations. As a result, the IOMMU hardware cannot
process the command which results in repeated "Completion-Wait loop
timed out" errors and a second kernel panic: "Kernel panic - not
syncing: timer doesn't work through Interrupt-remapped IO-APIC".
Reuse device table instead of copying device table in case of kdump
boot and remove all copying device table code.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/3a31036fb2f7323e6b1a1a1921ac777e9f7bdddc.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9be15fbfc6 ]
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/576445eb4f168b467b0fc789079b650ca7c5b037.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f32fe7cb01 ]
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU completion wait buffers (CWBs), command buffers and event buffer
registers remain locked and exclusive to the previous kernel. Attempts
to allocate and use new buffers in the kdump kernel fail, as hardware
ignores writes to the locked MMIO registers as per AMD IOMMU spec
Section 2.12.2.1.
This results in repeated "Completion-Wait loop timed out" errors and a
second kernel panic: "Kernel panic - not syncing: timer doesn't work
through Interrupt-remapped IO-APIC"
The list of MMIO registers locked and which ignore writes after failed
SNP shutdown are mentioned in the AMD IOMMU specifications below:
Section 2.12.2.1.
https://docs.amd.com/v/u/en-US/48882_3.10_PUB
Reuse the pages of the previous kernel for completion wait buffers,
command buffers, event buffers and memremap them during kdump boot
and essentially work with an already enabled IOMMU configuration and
re-using the previous kernel’s data structures.
Reusing of command buffers and event buffers is now done for kdump boot
irrespective of SNP being enabled during kdump.
Re-use of completion wait buffers is only done when SNP is enabled as
the exclusion base register is used for the completion wait buffer
(CWB) address only when SNP is enabled.
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Tested-by: Sairaj Kodilkar <sarunkod@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Link: https://lore.kernel.org/r/ff04b381a8fe774b175c23c1a336b28bc1396511.1756157913.git.ashish.kalra@amd.com
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb1745fc6 ]
Since the dma-resv is shared we don't need to reserve and add a fence
slot fence twice, plus no need to loop through the dependencies.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://lore.kernel.org/r/20250829164715.720735-2-matthew.auld@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c50729c68a ]
Handle the case where the hmm range partially covers a huge page (like
2M), otherwise we can potentially end up doing something nasty like
mapping memory which is outside the range, and maybe not even mapped by
the mm. Fix is based on the xe userptr code, which in a future patch
will directly use gpusvm, so needs alignment here.
v2:
- Add kernel-doc (Matt B)
- s/fls/ilog2/ (Thomas)
Reported-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://lore.kernel.org/r/20250828142430.615826-11-matthew.auld@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69777753a8 ]
When the EEPROM MAC is read by way of ADDRH, it can return all 0s the
first time. Subsequent reads succeed.
This is fully reproduceable on the Phytec PCM049 SOM.
Re-read the ADDRH when this behaviour is observed, in an attempt to
correctly apply the EEPROM MAC address.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://patch.msgid.link/20250903132610.966787-1-colin.foster@in-advantage.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2506af5f81 ]
The GuC communication protocol allows GuC to send NO_RESPONSE_RETRY
reply message to indicate that due to some interim condition it can
not handle incoming H2G request and the host shall resend it.
But in some cases, due to errors, this unsatisfied condition might
be final and this could lead to endless retries as it was recently
seen on the CI:
[drm] GT0: PF: VF1 FLR didn't finish in 5000 ms (-ETIMEDOUT)
[drm] GT0: PF: VF1 resource sanitizing failed (-ETIMEDOUT)
[drm] GT0: PF: VF1 FLR failed!
[drm:guc_ct_send_recv [xe]] GT0: H2G action 0x5503 retrying: reason 0x0
[drm:guc_ct_send_recv [xe]] GT0: H2G action 0x5503 retrying: reason 0x0
[drm:guc_ct_send_recv [xe]] GT0: H2G action 0x5503 retrying: reason 0x0
[drm:guc_ct_send_recv [xe]] GT0: H2G action 0x5503 retrying: reason 0x0
To avoid such dangerous loops allow only limited number of retries
(for now 50) and add some delays (n * 5ms) to slow down the rate of
resending this repeated request.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Reviewed-by: Julia Filipchuk <julia.filipchuk@intel.com>
Link: https://lore.kernel.org/r/20250903223330.6408-1-michal.wajdeczko@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c221cbf8dc ]
When the 3.3Vaux supply is present, fetch it at the probe time and keep it
enabled for the entire PCIe controller lifecycle so that the link can enter
L2 state and the devices can signal wakeup using either Beacon or WAKE#
mechanisms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded the subject, description and error message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250820022328.2143374-1-hongxing.zhu@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
