[ Upstream commit 9672ed3de7 ]
The ufs_mtk_clk_scale() trace event currently stores the address of the
name string directly via __field(const char *, name). This pointer may
become invalid after the module is unloaded, causing page faults when the
trace buffer is subsequently accessed.
This can occur because the MediaTek UFS driver can be configured as a
loadable module (tristate in Kconfig), meaning the name string passed to
the trace event may reside in module memory that becomes invalid after
module unload.
Fix this by using __string() and __assign_str() to copy the string contents
into the ring buffer instead of storing the pointer. This ensures the trace
data remains valid regardless of module state.
This change increases the memory usage for each ftrace entry by a few bytes
(clock names are typically 7-15 characters like "ufs_sel" or
"ufs_sel_max_src") compared to storing an 8-byte pointer.
Note that this change does not affect anything unless all of the following
conditions are met:
- CONFIG_SCSI_UFS_MEDIATEK is enabled
- ftrace tracing is enabled
- The ufs_mtk_clk_scale event is enabled in ftrace
Signed-off-by: Keita Morisaki <keita.morisaki@tier4.jp>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Link: https://patch.msgid.link/20260202024526.122515-1-keita.morisaki@tier4.jp
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5145b27730 ]
Explicitly set non-cached caching attributes for MMIO regions.
Default write-back mode can cause CPU to cache device memory,
causing invalid reads and unpredictable behavior.
Invalid read and write issues were observed on ARM64 when mapping the
notification area to userspace via mmap.
Signed-off-by: Kommula Shiva Shankar <kshankar@marvell.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20260102065703.656255-1-kshankar@marvell.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e17f0d4cc0 ]
Some randconfig builds run into excessive stack usage with gcc-14 or
higher, which use __attribute__((cold)) where earlier versions did not do
that:
drivers/scsi/BusLogic.c: In function 'blogic_init':
drivers/scsi/BusLogic.c:2398:1: error: the frame size of 1680 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
The problem is that a lot of code gets inlined into blogic_init() here. Two
functions stick out, but they are a bit different:
- blogic_init_probeinfo_list() actually uses a few hundred bytes of kernel
stack, which is a problem in combination with other functions that also
do. Marking this one as noinline means that the stack slots get get
reused between function calls
- blogic_reportconfig() has a few large variables, but whenever it is not
inlined into its caller, the compiler is actually smart enough to reuse
stack slots for these automatically, so marking it as noinline saves
most of the stack space by itself.
The combination of both of these should avoid the problem entirely.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260203163321.2598593-1-arnd@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8be14dd48d ]
After a RAS error occurs on the accelerator device, the accelerator
device will be reset. The live migration state will be abnormal
after reset, and the original state needs to be restored during
the reset process.
Therefore, reset processing needs to be performed in a live
migration scenario.
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/20260122020205.2884497-3-liulongfang@huawei.com
Signed-off-by: Alex Williamson <alex@shazbot.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 151cabd140 ]
When a SATA DAS enclosure is connected behind a Thunderbolt PCIe
switch, hot-unplugging the whole enclosure causes pciehp to tear down
the PCI hierarchy before the SCSI layer issues SYNCHRONIZE CACHE and
START STOP UNIT for the disks.
libata still queues these commands and the AHCI driver tries to access
the HBA registers even though the PCI channel is already offline. This
results in a series of timeouts and error recovery attempts, e.g.:
[ 824.778346] pcieport 0000:00:07.0: pciehp: Slot(14): Link Down
[ 891.612720] ata8.00: qc timeout after 5000 msecs (cmd 0xec)
[ 902.876501] ata8.00: qc timeout after 10000 msecs (cmd 0xec)
[ 934.107998] ata8.00: qc timeout after 30000 msecs (cmd 0xec)
[ 936.206431] sd 7:0:0:0: [sda] Synchronize Cache(10) failed:
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
...
[ 1006.298356] ata1.00: qc timeout after 5000 msecs (cmd 0xec)
[ 1017.561926] ata1.00: qc timeout after 10000 msecs (cmd 0xec)
[ 1048.791790] ata1.00: qc timeout after 30000 msecs (cmd 0xec)
[ 1050.890035] sd 0:0:0:0: [sdb] Synchronize Cache(10) failed:
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
With this patch applied, the same hot-unplug looks like:
[ 59.965496] pcieport 0000:00:07.0: pciehp: Slot(14): Link Down
[ 60.002502] sd 7:0:0:0: [sda] Synchronize Cache(10) failed:
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
...
[ 60.103050] sd 0:0:0:0: [sdb] Synchronize Cache(10) failed:
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
In this test setup with two disks, the hot-unplug sequence shrinks from
about 226 seconds (~3.8 minutes) between the Link Down event and the
last SYNCHRONIZE CACHE failure to under a second. Without this patch the
total delay grows roughly with the number of disks, because each disk
gets its own SYNCHRONIZE CACHE and qc timeout series.
If the underlying PCI device is already gone, these commands cannot
succeed anyway. Avoid issuing them by introducing
ata_adapter_is_online(), which checks pci_channel_offline() for
PCI-based hosts. It is used from ata_scsi_find_dev() to return NULL,
causing the SCSI layer to fail new commands with DID_BAD_TARGET
immediately, and from ata_qc_issue() to bail out before touching the
HBA registers.
Since such failures would otherwise trigger libata error handling,
ata_adapter_is_online() is also consulted from ata_scsi_port_error_handler().
When the adapter is offline, libata skips ap->ops->error_handler(ap) and
completes error handling using the existing path, rather than running
a full EH sequence against a dead adapter.
With this change, SYNCHRONIZE CACHE and START STOP UNIT commands
issued during hot-unplug fail quickly once the PCI channel is offline,
without qc timeout spam or long libata EH delays.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Henry Tseng <henrytseng@qnap.com>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc29063070 ]
When the connection establishment request is rejected from the server
side, then the actual error number sent back should be used.
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://patch.msgid.link/20260107161517.56357-10-haris.iqbal@ionos.com
Reviewed-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57be33f85e ]
For NXP NCI devices (e.g. PN7150), the interrupt is level-triggered and
active high, not edge-triggered.
Using IRQF_TRIGGER_RISING in the driver can cause interrupts to fail
to trigger correctly.
Remove IRQF_TRIGGER_RISING and rely on the IRQ trigger type configured
via Device Tree.
Signed-off-by: Carl Lee <carl.lee@amd.com>
Link: https://patch.msgid.link/20260205-fc-nxp-nci-remove-interrupt-trigger-type-v2-1-79d2ed4a7e42@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd24173439 ]
While compile testing on less common architectures, I noticed that gcc-10 on
s390 finds a bug that all other configurations seem to miss:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c: In function 'myri10ge_set_multicast_list':
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:391:25: error: 'cmd.data0' is used uninitialized in this function [-Werror=uninitialized]
391 | buf->data0 = htonl(data->data0);
| ^~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:392:25: error: '*((void *)&cmd+4)' is used uninitialized in this function [-Werror=uninitialized]
392 | buf->data1 = htonl(data->data1);
| ^~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c: In function 'myri10ge_allocate_rings':
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:392:13: error: 'cmd.data1' is used uninitialized in this function [-Werror=uninitialized]
392 | buf->data1 = htonl(data->data1);
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:1939:22: note: 'cmd.data1' was declared here
1939 | struct myri10ge_cmd cmd;
| ^~~
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:393:13: error: 'cmd.data2' is used uninitialized in this function [-Werror=uninitialized]
393 | buf->data2 = htonl(data->data2);
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:1939:22: note: 'cmd.data2' was declared here
1939 | struct myri10ge_cmd cmd;
It would be nice to understand how to make other compilers catch this as
well, but for the moment I'll just shut up the warning by fixing the
undefined behavior in this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patch.msgid.link/20260205162935.2126442-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81a2ce6b6 ]
After asserting Secondary Bus Reset to downstream devices via a GB10 Root
Port, the link may not retrain correctly, e.g., the link may retrain with a
lower lane count or config accesses to downstream devices may fail.
Prevent use of Secondary Bus Reset for devices below GB10.
Signed-off-by: Johnny-CC Chang <Johnny-CC.Chang@mediatek.com>
[bhelgaas: drop pci_ids.h update (only used once), update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20251113084441.2124737-1-Johnny-CC.Chang@mediatek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44d2f70b1f ]
The Qualcomm Hamoa & Glymur Root Ports don't advertise an ACS capability,
but they do provide ACS-like features to disable peer transactions and
validate bus numbers in requests.
Add an ACS quirk for Hamoa & Glymur.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260109-acs_quirk-v1-1-82adf95a89ae@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c41e2fb67e ]
Platform, ACPI, or IOMMU drivers call pci_request_acs(), which sets
'pci_acs_enable' to request that ACS be enabled for any devices enumerated
in the future.
OF platforms called pci_enable_acs() for the first device before
of_iommu_configure() called pci_request_acs(), so ACS was never enabled for
that device (typically a Root Port).
Call pci_enable_acs() later, from pci_dma_configure(), after
of_dma_configure() has had a chance to call pci_request_acs().
Here's the call path, showing the move of pci_enable_acs() from
pci_acs_init() to pci_dma_configure(), where it always happens after
pci_request_acs():
pci_device_add
pci_init_capabilities
pci_acs_init
- pci_enable_acs
- if (pci_acs_enable) <-- previous test
- ...
device_add
bus_notify(BUS_NOTIFY_ADD_DEVICE)
iommu_bus_notifier
iommu_probe_device
iommu_init_device
dev->bus->dma_configure
pci_dma_configure # pci_bus_type.dma_configure
of_dma_configure
of_iommu_configure
pci_request_acs
pci_acs_enable = 1 <-- set
+ pci_enable_acs
+ if (pci_acs_enable) <-- new test
+ ...
bus_probe_device
device_initial_probe
...
really_probe
dev->bus->dma_configure
pci_dma_configure # pci_bus_type.dma_configure
...
pci_enable_acs
Note that we will now call pci_enable_acs() twice for every device, first
from the iommu_probe_device() path and again from the really_probe() path.
Presumably that's not an issue since we also call dev->bus->dma_configure()
twice.
For the ACPI platforms, pci_request_acs() is called during ACPI
initialization time itself, independent of the IOMMU framework.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://patch.msgid.link/20260102-pci_acs-v3-1-72280b94d288@oss.qualcomm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f5e57c622 ]
Like pci_bus_lock(), pci_slot_lock() needs to lock the bridge device to
prevent warnings like:
pcieport 0000:e2:05.0: unlocked secondary bus reset via: pciehp_reset_slot+0x55/0xa0
Take and release the lock for the bridge providing the slot for the
lock/trylock and unlock routines.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Link: https://patch.msgid.link/20260130165953.751063-3-kbusch@meta.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e242d09b58 ]
Correctable and Uncorrectable Error Status Registers on reporting agents
are cleared upon PCI device enumeration in pci_aer_init() to flush past
events. They're cleared again when an error is handled by the AER driver.
If an agent reports a new error after pci_aer_init() and before the AER
driver has probed on the corresponding Root Port or Root Complex Event
Collector, that error is not handled by the AER driver: It clears the
Root Error Status Register on probe, but neglects to re-clear the
Correctable and Uncorrectable Error Status Registers on reporting agents.
The error will eventually be reported when another error occurs. Which
is irritating because to an end user it appears as if the earlier error
has just happened.
Amend the AER driver to clear stale errors on reporting agents upon probe.
Skip reporting agents which have not invoked pci_aer_init() yet to avoid
using an uninitialized pdev->aer_cap. They're recognizable by the error
bits in the Device Control register still being clear.
Reporting agents may execute pci_aer_init() after the AER driver has
probed, particularly when devices are hotplugged or removed/rescanned via
sysfs. For this reason, it continues to be necessary that pci_aer_init()
clears Correctable and Uncorrectable Error Status Registers.
Reported-by: Lucas Van <lucas.van@intel.com> # off-list
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Lucas Van <lucas.van@intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://patch.msgid.link/3011c2ed30c11f858e35e29939add754adea7478.1769332702.git.lukas@wunner.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb2f81792 ]
User forums report issues when assigning ASM1164 SATA controllers to VMs,
especially in configurations with multiple controllers. Logs show the
device fails to retrain after bus reset. Reports suggest this is an issue
across multiple platforms. The device indicates support for PM reset,
therefore the device still has a viable function level reset mechanism.
The reporting user confirms the device is well behaved in this use case
with bus reset disabled.
Reported-by: Patrick Bianchi <patrick.w.bianchi@gmail.com>
Link: https://forum.proxmox.com/threads/problems-with-pcie-passthrough-with-two-identical-devices.149003/
Signed-off-by: Alex Williamson <alex.williamson@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20260109000211.398300-1-alex.williamson@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b89fc7c252 ]
When canceling the reconnect worker, care must be taken to reset the
reconnect-pending bit. If the reconnect worker has not yet been
scheduled before it is canceled, the reconnect-pending bit will stay
on forever.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Link: https://patch.msgid.link/20260203055723.1085751-6-achender@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e25dbf561e ]
The gcc-16.0.1 snapshot produces a false-positive warning that turns
into a build failure with CONFIG_WERROR:
In file included from arch/x86/include/asm/string.h:6,
from net/vmw_vsock/vmci_transport.c:10:
In function 'vmci_transport_packet_init',
inlined from '__vmci_transport_send_control_pkt.constprop' at net/vmw_vsock/vmci_transport.c:198:2:
arch/x86/include/asm/string_32.h:150:25: error: argument 2 null where non-null expected because argument 3 is nonzero [-Werror=nonnull]
150 | #define memcpy(t, f, n) __builtin_memcpy(t, f, n)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
net/vmw_vsock/vmci_transport.c:164:17: note: in expansion of macro 'memcpy'
164 | memcpy(&pkt->u.wait, wait, sizeof(pkt->u.wait));
| ^~~~~~
arch/x86/include/asm/string_32.h:150:25: note: in a call to built-in function '__builtin_memcpy'
net/vmw_vsock/vmci_transport.c:164:17: note: in expansion of macro 'memcpy'
164 | memcpy(&pkt->u.wait, wait, sizeof(pkt->u.wait));
| ^~~~~~
This seems relatively harmless, and it so far the only instance of this
warning I have found. The __vmci_transport_send_control_pkt function
is called either with wait=NULL or with one of the type values that
pass 'wait' into memcpy() here, but not from the same caller.
Replacing the memcpy with a struct assignment is otherwise the same
but avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Bryan Tan <bryan-bt.tan@broadcom.com>
Link: https://patch.msgid.link/20260203163406.2636463-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a9424c756 ]
Several registers referenced in this driver's source code do not
actually exist (they are not writable and read as zero in my testing).
They exist in this driver because it originated as a copy of the dm9601
driver. Notably, these include the multicast filter registers - this
causes the driver to not support multicast packets correctly. Remove
the multicast filter code and register definitions. Instead, set the
chip to receive all multicast filter packets when any multicast
addresses are in the list.
Reviewed-by: Simon Horman <horms@kernel.org> (from v1)
Signed-off-by: Ethan Nelson-Moore <enelsonmoore@gmail.com>
Link: https://patch.msgid.link/20260203013924.28582-1-enelsonmoore@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61cef6454c ]
It appears that in commit 7efd79c0e6 ("bnxt_en: Add drop action
support for ntuple"), bnxt gained support for ntuple filters for packet
drops.
However, support for this does not seem to work in recent kernels or
against net-next:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
rmgr: Cannot insert RX class rule: Operation not supported
Cannot insert classification rule
The issue is that the existing code uses ethtool_get_flow_spec_ring_vf,
which will return a non-zero value if the ring_cookie is set to
RX_CLS_FLOW_DISC, which then causes bnxt_add_ntuple_cls_rule to return
-EOPNOTSUPP because it thinks the user is trying to set an ntuple filter
for a vf.
Fix this by first checking that the ring_cookie is not RX_CLS_FLOW_DISC.
After this patch, ntuple filters for drops can be added:
% sudo ethtool -U eth0 flow-type udp4 src-ip 1.1.1.1 action -1
Added rule with ID 0
% ethtool -n eth0
44 RX rings available
Total 1 rules
Filter: 0
Rule Type: UDP over IPv4
Src IP addr: 1.1.1.1 mask: 0.0.0.0
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
Action: Drop
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260131003042.2570434-1-joe@dama.to
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 820ba7dd68 ]
ath10k_wmi_event_peer_sta_ps_state_chg() uses lockdep_assert_held() to
assert that ar->data_lock should be held by the caller, but neither
ath10k_wmi_10_2_op_rx() nor ath10k_wmi_10_4_op_rx() acquire this lock
before calling this function.
The field arsta->peer_ps_state is documented as protected by
ar->data_lock in core.h, and other accessors (ath10k_peer_ps_state_disable,
ath10k_dbg_sta_read_peer_ps_state) properly acquire this lock.
Add spin_lock_bh()/spin_unlock_bh() around the peer_ps_state update,
and remove the lockdep_assert_held() to be aligned with new locking,
following the pattern used by other WMI event handlers in the driver.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Link: https://patch.msgid.link/20260123175611.767731-1-n7l8m4@u.northwestern.edu
[removed excess blank line]
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af1e82232b ]
The LDO (Low Dropout Regulator) setting is missing after suspend/resume
in some platforms, and it will cause card loss. Therefore, reconfigure
this setting to avoid it.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260127085036.44060-6-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86a8e8e0dd ]
Similar to Lantech 8330-262D-E, the Lantech 8330-265D also reports
2500MBd instead of 3125MBd.
Also, all 8330-265D report normal RX_LOS in EEPROM, but some signal
inverted RX_LOS. We therefore need to ignore RX_LOS on these modules.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://patch.msgid.link/20260128170044.15576-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70e9a5760a ]
NIX SQ manager sticky mode is known to cause stalls when multiple SQs
share an SMQ and transmit concurrently. Additionally, PSE may deadlock
on transitions between sticky and non-sticky transmissions. There is
also a credit drop issue observed when certain condition clocks are
gated.
work around these hardware errata by:
- Disabling SQM sticky operation:
- Clear TM6 (bit 15)
- Clear TM11 (bit 14)
- Disabling sticky → non-sticky transition path that can deadlock PSE:
- Clear TM5 (bit 23)
- Preventing credit drops by keeping the control-flow clock enabled:
- Set TM9 (bit 21)
These changes are applied via NIX_AF_SQM_DBG_CTL_STATUS. With this
configuration the SQM/PSE maintain forward progress under load without
credit loss, at the cost of disabling sticky optimizations.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260127125147.1642-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc6383d4f0 ]
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek
RTL8761BU Bluetooth adapter.
Reference:
https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth
Signed-off-by: Jacopo Scannella <code@charlie.cat>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49d0901e26 ]
hci_conn_enter_active_mode() uses queue_delayed_work() with the
intention that the work will run after the given timeout. However,
queue_delayed_work() does nothing if the work is already queued, so
depending on the link policy we may end up putting the connection
into idle mode every hdev->idle_timeout ms.
Use mod_delayed_work() instead so the work is queued if not already
queued, and the timeout is updated otherwise.
Signed-off-by: Stefan Sørensen <ssorensen@roku.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb091013a ]
The connection link policy is only set when establishing an outgoing
ACL connection causing connection idle modes not to be available on
incoming connections. Move the setting of the link policy to the
creation of the connection so all ACL connection will use the link
policy set on the HCI device.
Signed-off-by: Stefan Sørensen <ssorensen@roku.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dd1dda652 ]
il3945_store_measurement() calls il3945_get_measurement() which internally
calls il_send_cmd_sync() without holding il->mutex. However,
il_send_cmd_sync() has lockdep_assert_held(&il->mutex) indicating that
callers must hold this lock.
Other sysfs store functions in the same file properly acquire the mutex:
- il3945_store_flags() acquires mutex at 3945-mac.c:3110
- il3945_store_filter_flags() acquires mutex at 3945-mac.c:3144
Add mutex_lock()/mutex_unlock() around the il3945_get_measurement() call
in the sysfs store function to fix the missing lock protection.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260125193005.1090429-1-n7l8m4@u.northwestern.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e31fa691d0 ]
il4965_store_tx_power() calls il_set_tx_power() without holding il->mutex.
However, il_set_tx_power() has lockdep_assert_held(&il->mutex) indicating
that callers must hold this lock.
All other callers of il_set_tx_power() properly acquire the mutex:
- il_bg_scan_completed() acquires mutex at common.c:1683
- il_mac_config() acquires mutex at common.c:5006
- il3945_commit_rxon() and il4965_commit_rxon() are called via work
queues that hold the mutex (like il4965_bg_alive_start)
Add mutex_lock()/mutex_unlock() around the il_set_tx_power() call in
the sysfs store function to fix the missing lock protection.
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20260125194039.1196488-1-n7l8m4@u.northwestern.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878406d4d6 ]
Currently, HCLGE_FD_AD_QID has only 10 bits and supports a
maximum of 1023 queues. However, there are actually scenarios
where the queue_id exceeds 1023.
This patch adds an additional bit to HCLGE_FD_AD_QID to ensure
that queue_id greater than 1023 are supported.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20260123094756.3718516-2-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4faaf65a7 ]
idev->mr_maxdelay is read and written locklessly,
add READ_ONCE()/WRITE_ONCE() annotations.
While we are at it, make this field an u32.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260122172247.2429403-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fffa44b6e ]
Currently, ext4_zero_range passes EXT4_EX_NOCACHE flag to avoid caching
extents however this is not respected by convert_initialized_extent().
Hence, modify it to accept flags from the caller and to pass the flags
on to other extent manipulation functions it calls. This makes
sure the NOCACHE flag is respected throughout the code path.
Also, we no longer explicitly pass CONVERT_UNWRITTEN as the caller takes
care of this.
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/07008fbb14db727fddcaf4c30e2346c49f6c8fe0.1769149131.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad22d24be6 ]
RDS connections carry a state "rds_conn_path::cp_state"
and transitions from one state to another and are conditional
upon an expected state: "rds_conn_path_transition."
There is one exception to this conditionality, which is
"RDS_CONN_ERROR" that can be enforced by "rds_conn_path_drop"
regardless of what state the condition is currently in.
But as soon as a connection enters state "RDS_CONN_ERROR",
the connection handling code expects it to go through the
shutdown-path.
The RDS/TCP multipath changes added a shortcut out of
"RDS_CONN_ERROR" straight back to "RDS_CONN_CONNECTING"
via "rds_tcp_accept_one_path" (e.g. after "rds_tcp_state_change").
A subsequent "rds_tcp_reset_callbacks" can then transition
the state to "RDS_CONN_RESETTING" with a shutdown-worker queued.
That'll trip up "rds_conn_init_shutdown", which was
never adjusted to handle "RDS_CONN_RESETTING" and subsequently
drops the connection with the dreaded "DR_INV_CONN_STATE",
which leaves "RDS_SHUTDOWN_WORK_QUEUED" on forever.
So we do two things here:
a) Don't shortcut "RDS_CONN_ERROR", but take the longer
path through the shutdown code.
b) Add "RDS_CONN_RESETTING" to the expected states in
"rds_conn_init_shutdown" so that we won't error out
and get stuck, if we ever hit weird state transitions
like this again."
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Signed-off-by: Allison Henderson <allison.henderson@oracle.com>
Link: https://patch.msgid.link/20260122055213.83608-2-achender@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8da7e88682 ]
This fixes transmit power too low under 2GHz connection. Previously
we missed the settings of 2GHz, add the according calibrated tables.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260117044157.2392958-10-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f6d7a325f ]
During MLO connections, A1 of the probe responses we received are
in link address, these frames will then be dropped by mac80211 due to
not matching the MLD address in ieee80211_scan_accept_presp().
Fix this by using MLD address to scan when not using random MAC address.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260114013950.19704-13-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833dcd75d5 ]
When the TX queue length reaches the threshold, the netdev watchdog
immediately detects a TX queue timeout.
This patch updates the trans_start timestamp of the transmit queue
on every asynchronous USB URB submission along the transmit path,
ensuring that the network watchdog accurately reflects ongoing
transmission activity.
Signed-off-by: Mingj Ye <insyelu@gmail.com>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://patch.msgid.link/20260120015949.84996-1-insyelu@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dfffa5479 ]
When compiling a driver written for MIPS on OpenRISC that uses the nop()
function, it fails due to the following error:
drivers/watchdog/pic32-wdt.c: Assembler messages:
drivers/watchdog/pic32-wdt.c:125: Error: unrecognized instruction `nop'
The driver currently uses the generic version of nop() from
include/asm-generic/barrier.h:
#ifndef nop
#define nop() asm volatile ("nop")
#endif
Let's fix this on OpenRISC by defining an architecture-specific version
of nop().
This was tested by performing an allmodconfig openrisc cross compile on
an aarch64 host.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202601180236.BVy480We-lkp@intel.com/
Signed-off-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 735ee8582d ]
Quoting reporter:
In net/netfilter/xt_tcpmss.c (lines 53-68), the TCP option parser reads
op[i+1] directly without validating the remaining option length.
If the last byte of the option field is not EOL/NOP (0/1), the code attempts
to index op[i+1]. In the case where i + 1 == optlen, this causes an
out-of-bounds read, accessing memory past the optlen boundary
(either reading beyond the stack buffer _opt or the
following payload).
Reported-by: sungzii <sungzii@pm.me>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a49fc8d8a ]
The upstream commit, 71d8c47fc6
("netfilter: conntrack: introduce clash resolution on insertion race"),
sets allow_clash=true in the UDP/UDPLITE protocol handler
but does not set it in the generic protocol handler.
As a result, packets composed of connectionless protocols at each layer,
such as UDP over IP-in-IP, still drop packets due to conflicts during conntrack insertion.
To resolve this, this patch sets allow_clash in the nf_conntrack_l4proto_generic.
Signed-off-by: Yuto Hamaguchi <Hamaguchi.Yuto@da.MitsubishiElectric.co.jp>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01942af95a ]
When performing buffered writes, we may need to split and convert an
unwritten extent into a written one during the end I/O process. However,
we do not reserve space specifically for these metadata changes, we only
reserve 2% of space or 4096 blocks. To address this, we use
EXT4_GET_BLOCKS_PRE_IO to potentially split extents in advance and
EXT4_GET_BLOCKS_METADATA_NOFAIL to utilize reserved space if necessary.
These two approaches can reduce the likelihood of running out of space
and losing data. However, these methods are merely best efforts, we
could still run out of space, and there is not much difference between
converting an extent during the writeback process and the end I/O
process, it won't increase the risk of losing data if we postpone the
conversion.
Therefore, also use EXT4_GET_BLOCKS_METADATA_NOFAIL in
ext4_convert_unwritten_extents_endio() to prepare for the buffered I/O
iomap conversion, which may perform extent conversion during the end I/O
process.
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Link: https://patch.msgid.link/20260105014522.1937690-2-yi.zhang@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f8dd813a1 ]
Fast commits only log operations that have dedicated replay support.
EXT4_IOC_GROUP_EXTEND grows the filesystem to the end of the last
block group and updates the same on-disk metadata without going
through the fast commit tracking paths.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
EXT4_IOC_GROUP_EXTEND grows the filesystem.
This forces those transactions to fall back to a full commit,
ensuring that the group extension changes are captured by the normal
journal rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes online
resize via GROUP_EXTEND safer and easier to reason about under fast
commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_resize.img bs=1M count=0 seek=256
mkfs.ext4 -O fast_commit -F /root/fc_resize.img
mkdir -p /mnt/fc_resize && mount -t ext4 -o loop /root/fc_resize.img /mnt/fc_resize
2. Extended the filesystem to the end of the last block group using a
helper that calls EXT4_IOC_GROUP_EXTEND on the mounted filesystem
and checked fc_info:
./group_extend_helper /mnt/fc_resize
cat /proc/fs/ext4/loop0/fc_info
shows the "Resize" ineligible reason increased.
3. Fsynced a file on the resized filesystem and confirmed that the fast
commit ineligible counter incremented for the resize transaction:
touch /mnt/fc_resize/file
/root/fsync_file /mnt/fc_resize/file
sync
cat /proc/fs/ext4/loop0/fc_info
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-6-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2705645134 ]
When running `kvm-xfstests -c ext4/1k -C 1 generic/383` with the
`DOUBLE_CHECK` macro defined, the following panic is triggered:
==================================================================
EXT4-fs error (device vdc): ext4_validate_block_bitmap:423:
comm mount: bg 0: bad block bitmap checksum
BUG: unable to handle page fault for address: ff110000fa2cc000
PGD 3e01067 P4D 3e02067 PUD 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 2386 Comm: mount Tainted: G W
6.18.0-gba65a4e7120a-dirty #1152 PREEMPT(none)
RIP: 0010:percpu_counter_add_batch+0x13/0xa0
Call Trace:
<TASK>
ext4_mark_group_bitmap_corrupted+0xcb/0xe0
ext4_validate_block_bitmap+0x2a1/0x2f0
ext4_read_block_bitmap+0x33/0x50
mb_group_bb_bitmap_alloc+0x33/0x80
ext4_mb_add_groupinfo+0x190/0x250
ext4_mb_init_backend+0x87/0x290
ext4_mb_init+0x456/0x640
__ext4_fill_super+0x1072/0x1680
ext4_fill_super+0xd3/0x280
get_tree_bdev_flags+0x132/0x1d0
vfs_get_tree+0x29/0xd0
vfs_cmd_create+0x59/0xe0
__do_sys_fsconfig+0x4f6/0x6b0
do_syscall_64+0x50/0x1f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
==================================================================
This issue can be reproduced using the following commands:
mkfs.ext4 -F -q -b 1024 /dev/sda 5G
tune2fs -O quota,project /dev/sda
mount /dev/sda /tmp/test
With DOUBLE_CHECK defined, mb_group_bb_bitmap_alloc() reads
and validates the block bitmap. When the validation fails,
ext4_mark_group_bitmap_corrupted() attempts to update
sbi->s_freeclusters_counter. However, this percpu_counter has not been
initialized yet at this point, which leads to the panic described above.
Fix this by moving the execution of ext4_percpu_param_init() to occur
before ext4_mb_init(), ensuring the per-CPU counters are initialized
before they are used.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Zhang Yi <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20251209133116.731350-1-libaokun@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89b4336fd5 ]
Fast commits only log operations that have dedicated replay support.
Online resize via EXT4_IOC_GROUP_ADD updates the superblock and group
descriptor metadata without going through the fast commit tracking
paths.
In practice these operations are rare and usually followed by further
updates, but mixing them into a fast commit makes the overall
semantics harder to reason about and risks replay gaps if new call
sites appear.
Teach ext4 to mark the filesystem fast-commit ineligible when
ext4_ioctl_group_add() adds new block groups.
This forces those transactions to fall back to a full commit,
ensuring that the filesystem geometry updates are captured by the
normal journal rather than partially encoded in fast commit TLVs.
This change should not affect common workloads but makes online
resize via GROUP_ADD safer and easier to reason about under fast
commit.
Testing:
1. prepare:
dd if=/dev/zero of=/root/fc_resize.img bs=1M count=0 seek=256
mkfs.ext4 -O fast_commit -F /root/fc_resize.img
mkdir -p /mnt/fc_resize && mount -t ext4 -o loop /root/fc_resize.img /mnt/fc_resize
2. Ran a helper that issues EXT4_IOC_GROUP_ADD on the mounted
filesystem and checked the resize ineligible reason:
./group_add_helper /mnt/fc_resize
cat /proc/fs/ext4/loop0/fc_info
shows "Resize": > 0.
3. Fsynced a file on the resized filesystem and verified that the fast
commit stats report at least one ineligible commit:
touch /mnt/fc_resize/file
/root/fsync_file /mnt/fc_resize/file
sync
cat /proc/fs/ext4/loop0/fc_info
shows fc stats ineligible > 0.
Signed-off-by: Li Chen <me@linux.beauty>
Link: https://patch.msgid.link/20251211115146.897420-5-me@linux.beauty
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ade47c974 ]
Add missing READ_ONCE() when reading ipv6.sysctl.flowlabel_reflect,
as its value can be changed under us.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20260115094141.3124990-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e69fda4d07 ]
According to Wi-Fi Aware (TM) 4.0 specification 2.8, A NAN device can
have one NAN management interface. This applies also to multi radio
devices.
The current code allows a driver to support more than one NAN interface,
if those are not in the same radio.
Fix it.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20260107135129.fdaecec0fe8a.I246b5ba6e9da3ec1481ff197e47f6ce0793d7118@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
