The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.
Reported-by: GSR <gsr.bugs@infernal-iceberg.com>
Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978
Fixes: 8fb2e440b2 (cpupower: Show Intel turbo ratio support via ...)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull turbostat utility fixes for v4.11 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Array index 'i' is used before limits check.
Fix this by doing limits check first.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case count is not multiple of 4, there is a read access in
wil_memcpy_toio_32() from outside src buffer boundary.
In wil_memcpy_fromio_32(), in case count is not multiple of 4, there is
a write access to outside dst io memory boundary.
Fix these issues with proper handling of the last 1 to 4 copied bytes.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver fails to load FW for sparrow D0 devices in some cases.
Fix this by returning correct value from wil_fw_verify_file_exists
when D0 FW file is not detected for any reason.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During the suspend flow, wil6210 HW can send sporadic interrupts,
while PCIe bus is not operational.
To prevent that, keep the interrupts disabled during the suspend
flow and re-enable them only after PCIe enablement in resume.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing code that ignores connection events during
reset flow will never take effect since it locks the
same mutex taken by the reset flow.
In addition, in case of unsolicited disconnect events ignore
those as well since device is about to get reset.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Communication with FW must be done before wil->status
is initialized in order to properly handle cases where
communication with FW halts during reset sequence.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In 'ath10k_ce_alloc_pipe' the compile time sanity check to
ensure that there is sufficient buffers in CE4 for HTT Tx
MSDU descriptors, but this did not take into account of the
case with 'peer flow control' enabled, fix this.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix fallout too.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are two bugs in the follow-MAC code:
* it treats the radiotap header as the 802.11 header
(therefore it can't possibly work)
* it doesn't verify that the skb data it accesses is actually
present in the header, which is mitigated by the first point
Fix this by moving all of this out into a separate function.
This function copies the data it needs using skb_copy_bits()
to make sure it can be accessed if it's paged, and offsets
that by the possibly present vendor radiotap header.
This also makes all those conditions more readable.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Interrupt numbers are never negative, zero serves as the special invalid
value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We ignore the d1 and d2 dividers in the audio PLL, and force them to
1 (register value 0) at probe time. However the comment preceding the
audio PLL definition says we enforce the default value, which is not
the same.
Fix the preceding comment to match what we do in code.
Fixes: b8eb71dcdd ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In commit 2beaa601c8 ("clk: sunxi-ng: Implement minimum for
multipliers"), the multiplier minimums in the set_rate callback
for NM and NKMP style clocks were not updated.
This patch fixes them to match their round_rate callbacks.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A zero multiplier does not make sense for clocks.
Use 1 as the minimum when a multiplier minimum isn't specified.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Apparently some DP sinks are a little nuts and cause HPD to drop
intermittently during modesets. This happens eg. on an ASUS PB287Q.
In oder to recover from this we can't really use the previous
connector status to determine if the link needs retraining, so let's
just ignore that piece of information and do the retrain
unconditionally. We do of course still check whether the link is
supposed to be running or not.
To actually get read out the EDID and update things properly we
also need to nuke the goto out added by commit 7d23e3c37b
("drm/i915: Cleaning up intel_dp_hpd_pulse"). I'm actually not sure
why that was there. Perhaps to avoid an EDID read if the connector
status didn't appear to change, but that sort of thing is quite racy
and would have failed anyway if we failed to keep up with the
hotplugs (if we missed the HPD down in between two HPD ups). And
now that we take this codepath unconditionally we definitely need
to drop the goto as otherwise we would never do the EDID read.
v2: Drop the goto that made us skip EDID reads entirely. Doh!
v3: Rebase due to locking changes
s/apparely/apparently/ in the comment (Chris)
Cc: stable@vger.kernel.org
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Reported-by: Palmer Dabbelt <palmer@dabbelt.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99766
References: https://lists.freedesktop.org/archives/intel-gfx/2017-February/119779.html
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170412193017.21029-1-ville.syrjala@linux.intel.com
When channel contexts are used, there's no global power level
(the power_level is always 0). Use the per-interface TX power
in mac80211_hwsim to have a proper setting for both cases.
This fixes the bgscan_simple and bgscan_learn test cases when
the number of channels advertised by hwsim is >1 by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code to have common code for changing monitor
options when adding and changing virtual interfaces. This
will make it easier to add BPF filters to both paths. Note
that this code carefully checks the error conditions first
and only then applies the changes, to guarantee atomicity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the parsing of monitor flags and the MU-MIMO options.
This will allow adding more things cleanly in the future and
also allows setting the latter already when creating a monitor
interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MU-MIMO monitor follow functionality is broken because it
doesn't clear the MU-MIMO owner even if both follow features
are disabled. Fix that, and while at it move the code into a
new helper function. Call this also when creating a new monitor
interface to prepare for an upcoming cfg80211 change allowing
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing monitor parameters, not setting the MU-MIMO attributes
should mean that they're not changed - it's documented that to turn
the feature off it's necessary to set all-zero group membership and
an invalid follow-address. This isn't implemented.
Fix this by making the parameters pointers, stop reusing the macaddr
struct member, and documenting that NULL pointers mean unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of dropping such frames only when removing the
monitor info, drop them earlier (keeping the warning)
and simplify removing monitor info. While at it, make
that function return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wopcm registers are write-once, so any write after the first one
will just be ignored. The registers survive a GPU reset but not
always a suspend/resume cycle, so to keep things simple keep the
writes in the intel_uc_init_hw function instead of moving it earlier
to make sure we attempt them every time we try to load GuC.
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491524332-23860-1-git-send-email-daniele.ceraolospurio@intel.com
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds a driver for the Nokia H4+ protocol, which is used
at least on the Nokia N9, N900 & N950.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add binding document for serial bluetooth chips using
Nokia H4+ protocol.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Geminilake vendor nid is different from other Skylake variants, but rest
of the initialization code is same.
So a variable is added in hdmi_spec to store the platform specific vendor
nid and move the initialization code to a helper function to be used by
both platform specific init.
Fixes: 126cfa2f5e ("ALSA: hda: Add Geminilake HDMI codec ID")
Signed-off-by: Ander Conselvan De Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Cc: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=A/S/
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, gvt, nouveau, udl and etnaviv fixes.
I was away the end of last week, so some of these would have been in
rc6, and it's Easter from tomorrow, so I decided I better dequeue what
I have now.
The nouveau changes, just add a hw enable for GP107 display (like a
pci id addition really), and fix a couple of regressions. i915 has
some more gvt fixes, along with a few run of the mill ones, the rcu
one seems like a few people have hit it.
Otherwise a small udl and small etnaviv fix"
* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
drm/udl: Fix unaligned memory access in udl_render_hline
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
...
This contain a fix for the atomic update support recently added to the
Rockchip driver where the clock reference count would become unbalanced
and result in the clock feeding the PWM to always be disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration.
-----BEGIN PGP SIGNATURE-----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=ftQo
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"This contain a fix for the atomic update support recently added to
the Rockchip driver where the clock reference count would become
unbalanced and result in the clock feeding the PWM to always be
disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration"
* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
pwm: lpss: Set enable-bit before waiting for update-bit to go low
pwm: lpss: Split Tangier configuration
When clang detects a non-boolean constant in a logical operation it
generates a 'constant-logical-operand' warning. In
ieee80211_try_rate_control_ops_get() the result of strlen(<const str>)
is used in a logical operation, clang resolves the expression to an
(integer) constant at compile time when clang's builtin strlen function
is used.
Change the condition to check for strlen() > 0 to make the constant
operand boolean and thus avoid the warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reserving a runtime region results in splitting the EFI memory
descriptors for the runtime region. This results in runtime region
descriptors with bogus memory mappings, leading to interesting crashes
like the following during a kexec:
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1 #53
Hardware name: Wiwynn Leopard-Orv2/Leopard-DDR BW, BIOS LBM05 09/30/2016
RIP: 0010:virt_efi_set_variable()
...
Call Trace:
efi_delete_dummy_variable()
efi_enter_virtual_mode()
start_kernel()
? set_init_arg()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
...
Kernel panic - not syncing: Fatal exception
Runtime regions will not be freed and do not need to be reserved, so
skip the memmap modification in this case.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 8e80632fb2 ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Link: http://lkml.kernel.org/r/20170412152719.9779-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As those debug messages might appear in every timer call for scheduler,
it's too noisy, eat too much log and aren't meaningful. So remove them.
Cc: Ping Gao <ping.a.gao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
We want dax capable drivers to be able to publish a set of dax
operations [1]. However, we do not want to further abuse block_devices
to advertise these operations. Instead we will attach these operations
to a dax device and add a lookup mechanism to go from block device path
to a dax device. A dax capable driver like pmem or brd is responsible
for registering a dax device, alongside a block device, and then a dax
capable filesystem is responsible for retrieving the dax device by path
name if it wants to call dax_operations.
For now, we refactor the dax pseudo-fs to be a generic facility, rather
than an implementation detail, of the device-dax use case. Where a "dax
device" is just an inode + dax infrastructure, and "Device DAX" is a
mapping service layered on top of that base 'struct dax_device'.
"Filesystem DAX" is then a mapping service that layers a filesystem on
top of that same base device. Filesystem DAX is associated with a
block_device for now, but perhaps directly to a dax device in the
future, or for new pmem-only filesystems.
[1]: https://lkml.org/lkml/2017/1/19/880
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for introducing a struct dax_device type to the kernel
global type namespace, rename dax_dev to dev_dax. A 'dax_device'
instance will be a generic device-driver object for any provider of dax
functionality. A 'dev_dax' object is a device-dax-driver local /
internal instance.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>