The reset deassert time for the DP83TD510E is incorrectly set to
60000us, while the datasheet states that the minimum time required
after an hard reset is 30us (while 60ms is the time required for the
Power-On Reset after supply stabilization). The error probably arose
from the two timings being indicated by the same symbol (T2).
Lower the required time to 35us, aligning it to the value required for
the PHY to complete the reset AND to be able to accept the RMII master
clock. This saves ~60ms on boot if the MDIO driver is built-in.
Signed-off-by: Francesco Valla <francesco@valla.it>
Link: https://lore.kernel.org/r/20250105162630.243899-1-francesco@valla.it
Signed-off-by: Nishanth Menon <nm@ti.com>
SolidRun HummingBoard-T has two options for M.2 connector, supporting
either PCI-E or USB-3.1 Gen 1 - depending on configuration of a mux
on the serdes lane.
The required configurations in device-tree were modeled as overlays.
The USB-3.1 overlay uses /delete-property/ to unset a boolean property
on the usb controller limiting it to USB-2.0 by default.
Overlays can not delete a property from the base dtb, therefore this
overlay is at this time useless.
Convert both overlays into full dts by including the base board dts.
While the pcie overlay was functional, both are converted for a
consistent user experience when selecting between the two mutually
exclusive configurations.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-devicetree/CAMuHMdXTgpTnJ9U7egC2XjFXXNZ5uiY1O+WxNd6LPJW5Rs5KTw@mail.gmail.com
Fixes: bbef42084c ("arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3")
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20250101-am64-hb-fix-overlay-v2-1-78143f5da28c@solid-run.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on AM68-SK-Base-Board in
Endpoint mode of operation. PCIE1 on AM68-SK-Base-Board supports x2 Lane
operation unlike its counterpart on J721S2-EVM which supports x1 Lane.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-4-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add overlay to enable the PCIE1 instance of PCIe on J721E-EVM in Endpoint
mode of operation. Additionally, in order to support both PCIE0 and PCIE1
in Endpoint Mode of operation, enable applying device-tree overlays on
"k3-j721e-evm-pcie0-ep.dtb", thereby allowing the overlay for PCIE1 in
Endpoint mode to be applied on the aforementioned DTB.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The list of "dtbs" should contain the resultant "dtb" formed by applying
the "dtbo" overlay on the base "dtb", rather than the "dtbo" itself.
Hence, change "k3-j7200-evm-pcie1-ep.dtbo" to "k3-j7200-evm-pcie1-ep.dtb"
in the list of "dtbs".
Fixes: f43ec89bbc ("arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint Mode")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205105041.749576-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
CTRLMMR_MCU_SPI1_CTRL register controls if MCU_SPI1 is directly
connected to SPI3 in the MAIN Domain (default) or if MCU_SPI1
and SPI3 are independently pinned out. By default, the field
SPI1_LINKDIS (Bit 0) is set to 0h. In order to disable the direct
connection, the SPI1_LINKDIS (Bit 0) needs to be set to 1h. Model
this functionality as a "reg-mux" device and based on the idle-state
property, enable/disable the connection bewtween MCU_SPI1 and MAIN_SPI3.
The register field description has been referred from J7200 TRM [1]
(Table 5-517. CTRLMMR_MCU_SPI1_CTRL Register Field Descriptions).
[1] https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Link: https://lore.kernel.org/r/20241127075644.210759-1-a-dutta@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the "bootph-all" property to the "usb0" device-tree node. This is
required for the USB0 instance of USB to be functional at all stages
of USB DFU boot.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241220054550.153360-1-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The GIC Redistributor control range is mapped twice. Remove the extra
entry from the reg range.
Fixes: 5fc6b1b626 ("arm64: dts: ti: Introduce AM62A7 family of SoCs")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20241210-am62-gic-fixup-v1-2-758b4d5b4a0a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The GIC Redistributor control register range is mapped twice. Remove
the extra entry from the reg range.
Fixes: f1d17330a5 ("arm64: dts: ti: Introduce base support for AM62x SoC")
Reported-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20241210-am62-gic-fixup-v1-1-758b4d5b4a0a@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add nodes for the R5F and C7x cores on the SoC. This includes the mailbox
and memory carveouts used by these remote cores.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20241203174114.94751-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Mailbox nodes defined in the top-level J722s/AM62p SoC dtsi files are
incomplete and may not be functional unless they are extended with a
chosen interrupt and connection to a remote processor.
Disable the Mailbox nodes in the dtsi files and only enable the ones
that are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20241203174114.94751-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This node is already defined in the included k3-am62x-sk-common.dtsi.
Remove this redefinition.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20241203164031.20211-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable support for mcu_i2c0 and add pinmux required to bring out the
mcu_i2c0 signals on 40-pin RPi expansion header on the J722S EVM.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Shreyash Sinha <s-sinha@ti.com>
Reviewed-by: Prasanth Babu Mantena <p-mantena@ti.com>
Link: https://lore.kernel.org/r/20241105091224.23453-1-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Ethernet boot requires CPSW node to be present starting from R5 SPL stage.
Add bootph-all property in CPSW MAC's eFuse node cpsw_mac_syscon to enable
this node during SPL stage along with later boot stages so that CPSW port
will get static MAC address.
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://lore.kernel.org/r/20241114165331.1279065-1-c-vankar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Remove "ti,(rx|tx)-fifo-depth" properties which are both unused in the
kernel and undocumented. Most likely they are leftovers from downstream.
There are similar properties, but DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
represents the default value so adding them is not necessary.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241115193359.3618020-1-robh@kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
ICSSG has 7 available clocks per instance. Add all the cloks to ICSSG
nodes. ICSSG currently uses ICSSG_ICLK (clk id 20) which operates at
250MHz. Switch ICSSG clock to ICSSG_CORE clock (clk id 0) which operates at
333MHz.
ICSSG_CORE clock will help get the most out of ICSSG as more cycles are
needed to fully support all ICSSG features.
This commit also changes assigned-clock-parents of coreclk-mux to
ICSSG_CORE clock from ICSSG_ICLK.
Performance update in dual mac mode
With ICSSG_CORE Clk @ 333MHz
Tx throughput - 934 Mbps
Rx throughput - 914 Mbps,
With ICSSG_ICLK clk @ 250MHz,
Tx throughput - 920 Mbps
Rx throughput - 706 Mbps
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Tested-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241113110955.3876045-3-danishanwar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The ICSSG module has 7 clocks for each instance.
These clocks are ICSSG0_CORE_CLK, ICSSG0_IEP_CLK, ICSSG0_ICLK,
ICSSG0_UART_CLK, RGMII_MHZ_250_CLK, RGMII_MHZ_50_CLK and RGMII_MHZ_5_CLK
These clocks are described in AM64x TRM Section 6.4.3 Table 6-398.
Add these clocks to the dt binding of ICSSG.
Link: https://www.ti.com/lit/pdf/spruim2 (AM64x TRM)
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20241113110955.3876045-2-danishanwar@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
In order for the MCU domain to access this PMIC, a regulator
needs to be marked appropriately otherwise it is not seen by SPL and
therefore not configured.
This is necessary if the MCU domain is to program the TPS6594 MCU ESM
state machine, which is required to wire up the watchdog in a manner
that will reset the board.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Beleswar Padhi <b-padhi@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Enric Balletbo i Serra <eballetb@redhat.com>
Link: https://lore.kernel.org/r/20241113-b4-j784s4-tps6594-bootph-v4-2-102ddaa1bdc6@redhat.com
Signed-off-by: Nishanth Menon <nm@ti.com>
In order for the MCU domain to access this PMIC, a regulator
needs to be marked appropriately otherwise it is not seen by SPL and
therefore not configured.
This is necessary if the MCU domain is to program the TPS6594 MCU ESM
state machine, which is required to wire up the watchdog in a manner
that will reset the board.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Beleswar Padhi <b-padhi@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Enric Balletbo i Serra <eballetb@redhat.com>
Link: https://lore.kernel.org/r/20241113-b4-j784s4-tps6594-bootph-v4-1-102ddaa1bdc6@redhat.com
Signed-off-by: Nishanth Menon <nm@ti.com>
After the SoC has entered the Deep Sleep mode, USB1 can be used to wakeup
the SoC based on USB events triggered by USB devices. This requires that
the pin corresponding to the Type-A connector remains pulled up even after
the SoC has entered the Deep Sleep mode. Hence, enable Deep Sleep pullup /
pulldown selection for the USB1_DRVVBUS pin and set its Deep Sleep state to
PULL_UP.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205120134.754664-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The behavior of pins in deep sleep mode can be configured by programming
the corresponding bits in the respective Pad Configuration register. Add
macros to support this.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241205120134.754664-2-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add the missing vcc-supply property to the EEPROM node which resolves
the following warning:
at24 1-0051: supply vcc not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-4-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Specify the regulator for the EEPROM supply voltage and associate it
with the EEPROM device. This resolves the following warning:
at24 0-0050: supply vcc not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-3-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
Specify I/0 voltage & core supply regulators used by the SII902x
HDMI bridge and make them known to the bridge.
This resolves the following warning:
sii902x 1-0039: supply iovcc not found, using dummy regulator
sii902x 1-0039: supply cvcc12 not found, using dummy regulator
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-2-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
The phyBOARD-Lyra connects only 16 pins to the SII902x HDMI bridge's RGB
input. The default 24-bit setting causes incorrect color output. Update
to 16-bit to match the hardware configuration.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20241101131427.3815341-1-w.egorov@phytec.de
Signed-off-by: Nishanth Menon <nm@ti.com>
core: add of based component probing
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular device
can be detected by some firmware provided identifier, other times that
information is not available, and the kernel has to try to probe each
device.
Instead of a delicate dance between drivers and device tree quirks, this
change introduces a simple I2C component probe function. For a given
class of devices on the same I2C bus, it will go through all of them,
doing a simple I2C read transfer and see which one of them responds. It
will then enable the device that responds.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEOZGx6rniZ1Gk92RdFA3kzBSgKbYFAmdMOCwACgkQFA3kzBSg
KbaLWQ//e+29c9Trh+Typ6YCknuCFmM12xNUEPgce93EldERZjfCsdlHEchJnjEe
RX5Mw+UxT7NqFUD6G2YQQw35LMj/PDws4Q/q3OwAvurj2PqoKEGIbdTxUEbGrLtT
aYRUjGoqjPk3gAkqfKEQp8X8bvqKJfQ/xeXcZyy7Ij8xPU1LC/W6So4vpZA7oZkZ
UfwrUXu2NM/DKfLATeSH3vnlBrrpco9BdjImDanP8BpuYHQ0aNt7IToDytd3/rLZ
WKQPbHqVzzBUHm8Tf+DTyeVtII/ID078z+RW7htPrzPtzhVu2DN56w3z7/+EsVIy
XKb1PiJo5HlFev4gxhIcUgf8L5JYE8MyU8eeRWAcDObiBYVcSP34P7Xoykczjuq9
22IFNSdaqMVdigo9v4p7U99fVjoi3oUqIVsSb2HkmND8bPw3+jtyq1GxTFvTeOw8
EVJGuGjYrPiko26zNgK/WZaumpB+fsH7uRioSb1ejlSQk0BcNv4YqjYaMx9aT7Xj
+zF7luuxpkWTkPCjk57GX55K/BFzkA9jhJdKqjImBS+Q9Rn3k5bHyRdNPUDIeWs0
Yl5dhg6QbLHyuPC2R/hJiV6X4uFloH9+Oh99T3lLzcVNc2mllPQDN9F4I8q5nWB8
Eq5U95fnegfdVkiWnbNCnTCux/mypm35Gx46BffTiAJL2U9pSIE=
=MAxU
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
- Remove unused bprintf() function
bprintf() was added with the rest of the "bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZ0yNShQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qmJ6AP9i8pFOjeMfb2hOBpJTzORkIXEbz5nG
OCK/5aeSdjxy8QEAqafBSr5IQOxaTCFve1p7WSwdgmi2ZLmqEasaud0LmAk=
=5bp1
-----END PGP SIGNATURE-----
Merge tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function __udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
-----BEGIN PGP SIGNATURE-----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=X4bb
-----END PGP SIGNATURE-----
Merge tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause some
virtual interrupts to get lost
- More platform_driver::remove() conversion
-----BEGIN PGP SIGNATURE-----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=xeni
-----END PGP SIGNATURE-----
Merge tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Move the ->select callback to the correct ops structure in
irq-mvebu-sei to fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause
some virtual interrupts to get lost
- More platform_driver::remove() conversion
* tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Switch back to struct platform_driver::remove()
irqchip/gicv3-its: Add workaround for hip09 ITS erratum 162100801
irqchip/irq-mvebu-sei: Move misplaced select() callback to SEI CP domain
by erratum 1386 so that the matching loop actually terminates instead of
going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the relocatable
kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN has been
disabled
-----BEGIN PGP SIGNATURE-----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=RC2M
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add a terminating zero end-element to the array describing AMD CPUs
affected by erratum 1386 so that the matching loop actually
terminates instead of going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the
relocatable kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN
has been disabled
* tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Terminate the erratum_1386_microcode array
x86/Documentation: Update algo in init_size description of boot protocol
x86/microcode/AMD: Flush patch buffer mapping after application
x86/mm: Carve out INVLPG inline asm for use by others
x86/cpu: Fix PPIN initialization
The point behind strscpy() was to once and for all avoid all the
problems with 'strncpy()' and later broken "fixed" versions like
strlcpy() that just made things worse.
So strscpy not only guarantees NUL-termination (unlike strncpy), it also
doesn't do unnecessary padding at the destination. But at the same time
also avoids byte-at-a-time reads and writes by _allowing_ some extra NUL
writes - within the size, of course - so that the whole copy can be done
with word operations.
It is also stable in the face of a mutable source string: it explicitly
does not read the source buffer multiple times (so an implementation
using "strnlen()+memcpy()" would be wrong), and does not read the source
buffer past the size (like the mis-design that is strlcpy does).
Finally, the return value is designed to be simple and unambiguous: if
the string cannot be copied fully, it returns an actual negative error,
making error handling clearer and simpler (and the caller already knows
the size of the buffer). Otherwise it returns the string length of the
result.
However, there was one final stability issue that can be important to
callers: the stability of the destination buffer.
In particular, the same way we shouldn't read the source buffer more
than once, we should avoid doing multiple writes to the destination
buffer: first writing a potentially non-terminated string, and then
terminating it with NUL at the end does not result in a stable result
buffer.
Yes, it gives the right result in the end, but if the rule for the
destination buffer was that it is _always_ NUL-terminated even when
accessed concurrently with updates, the final byte of the buffer needs
to always _stay_ as a NUL byte.
[ Note that "final byte is NUL" here is literally about the final byte
in the destination array, not the terminating NUL at the end of the
string itself. There is no attempt to try to make concurrent reads and
writes give any kind of consistent string length or contents, but we
do want to guarantee that there is always at least that final
terminating NUL character at the end of the destination array if it
existed before ]
This is relevant in the kernel for the tsk->comm[] array, for example.
Even without locking (for either readers or writers), we want to know
that while the buffer contents may be garbled, it is always a valid C
string and always has a NUL character at 'comm[TASK_COMM_LEN-1]' (and
never has any "out of thin air" data).
So avoid any "copy possibly non-terminated string, and terminate later"
behavior, and write the destination buffer only once.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bprintf() is unused. Remove it. It was added in the commit 4370aa4aa7
("vsprintf: add binary printf") but as far as I can see was never used,
unlike the other two functions in that patch.
Link: https://lore.kernel.org/20241002173147.210107-1-linux@treblig.org
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Acked-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
-----BEGIN PGP SIGNATURE-----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=bPnr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
-----BEGIN PGP SIGNATURE-----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=ZCsN
-----END PGP SIGNATURE-----
Merge tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull ima fix from Paul Moore:
"One small patch to fix a function parameter / local variable naming
snafu that went up to you in the current merge window"
* tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: uncover hidden variable in ima_match_rules()
-----BEGIN PGP SIGNATURE-----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=6cbB
-----END PGP SIGNATURE-----
Merge tag 'block-6.13-20242901' of git://git.kernel.dk/linux
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
-----BEGIN PGP SIGNATURE-----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=b84h
-----END PGP SIGNATURE-----
Merge tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
* Fixes.
RISC-V:
* Svade and Svadu (accessed and dirty bit) extension support for host and
guest. This was acked on the mailing list by the RISC-V maintainer, see
https://patchew.org/linux/20240726084931.28924-1-yongxuan.wang@sifive.com/.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmdKS0QUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroP7hggAmt5CJesFGIuDwQgJX1KuNWAS84AX
Oq5SPZLH0XjE5YDm6AusSzvbtOhRM6mARU5/iqMRE6Mqpf4MXpP9tOo6xaDiL7+m
bOFsDYEO73WQyrIfFUCZ7dXiTbDVtQfNH8Z1yQwHPsa1d+WDYY3tLbCe5qCdqYMF
JDiB7K0cQzPDmhCwf3Zf8mW2ZRI0QsTqiuFUfVGGNgFDspWfBFBqkLCkrMNmbp9z
ye375oKb2VCe6OBJCY+Nl6tdoBUkz+CtZDCxkxuh0Uk4NmsUC9JMye9iwgU9DuI7
nagFuvpUGcgbZvrx1ly47TL+wcEFLwnBJ0xBZTGIgVoZHj/wX9GM+tSgIw==
=semZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
- sh: intc: Fix use-after-free bug in register_intc_controller()
- sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
-----BEGIN PGP SIGNATURE-----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=8ud9
-----END PGP SIGNATURE-----
Merge tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Two small fixes.
The first one by Huacai Chen addresses a runtime warning when
CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected
which occurs because the cpuinfo code on sh incorrectly uses NR_CPUS
when iterating CPUs instead of the runtime limit nr_cpu_ids.
A second fix by Dan Carpenter fixes a use-after-free bug in
register_intc_controller() which occurred as a result of improper
error handling in the interrupt controller driver code when
registering an interrupt controller during plat_irq_setup() on sh"
* tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: intc: Fix use-after-free bug in register_intc_controller()
sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE5RElWfyWxS+3PLO2a9axLQDIXvEFAmdKK6QACgkQa9axLQDI
XvFvxg//SIcw9gQL+2POTH4taZ5Xk4lsUyCKygVINhO54RE1iKMAhsr5qar7YQtE
0/sxOdHACqO0BATNGQMbwhHYvn7RkfcqnoXihvLxOwPp8Nqdf4W55eOIwQCPfVaZ
p2N/Iy2SYEO044gIH6N8KzoFLjH7hwvXDtaWD6o+Fq9NEAwLMRn55QyIGfyM//V3
6igBD1vjPKwxX7qIIlNqsn1l80jk8weF5uWeU1g06lSFSSRNGQ9PGT7oTLmgiKrl
8daE8E+1++rKmelANNe4CZ2Ig9tFNonaE8jRFuEJMEu/mZ5AAMksGh1M7eaz/ODU
ov6AukUVFRr+EsfSYlARhEgBKEssuRSDRiYuwTYPGHhDmyf+wNSu0u9K3p99DdJv
Fu55u4weVShg/ooOY3HtPWm3WnSoaxO7L4OOVd6yxeF2McUyRI9qFrADkpr4D3Sv
9aCGX9UdIuuTbEuXf3jacMhPq97QP9KAshWNEmzo9OZze7vLcbDz3IVeTanHIUOg
PieUgcnLW0dOxPz+tXYzOs3Ebf0pU8nQY3Eyj3YP7GsJkJMQh3usNC2t/oYhsnyj
OsohGT97CyBAgGtdlGsiNknIKisD3LIwa4gkJ+4sFIvFr5jfdrfCTvl23DieI8bf
9YETifEaSrJ+R/wzP0cMUUAauBC0gxS4HMPXGETe02U+ziGt3LU=
=ZNzJ
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
perf/arm-cmn: Ensure port and device id bits are set properly
perf/arm-smmuv3: Fix lockdep assert in ->event_init()
arm64: disable ARCH_CORRECT_STACKTRACE_ON_KRETPROBE tests
since 2024.07.26:
assorted minor bug fixes
assorted platform specific tweaks
initial RAPL PSYS (SysWatt) support
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce the counter as a part of global, platform counters structure.
We open the counter for only one cpu, but otherwise treat it as an
ordinary RAPL counter, allowing for grouped perf read.
The counter is disabled by default, because it's interpretation may
require additional, platform specific information, making it unsuitable
for general use.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add '+' to optstring when early scanning for --no-msr and --no-perf.
It causes option processing to stop as soon as a nonoption argument is
encountered, effectively skipping child's arguments.
Fixes: 3e4048466c ("tools/power turbostat: Add --no-msr option")
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Force the --no-perf early to prevent using it as a source. User asks for
raw values, but perf returns them relative to the opening of the file
descriptor.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, the graphics device is enumerated as
/sys/class/drm/card1 instead of /sys/class/drm/card0. The current
implementation does not handle this scenario, resulting in the loss of
graphics C6 residency and frequency information.
Add support for /sys/class/drm/card1, ensuring that turbostat can
retrieve and display the graphics columns for these platforms.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
