cgroup/for-6.12 is about to receive updates that are dependent on changes
from both for-6.11-fixes and for-6.12. Pull in for-6.11-fixes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Take into account the plane rotation and flipping when calculating src
positions for the wide plane parts.
This is not an issue yet, because rotation is only supported for the
UBWC planes and wide UBWC planes are rejected anyway because in parallel
multirect case only the half of the usual width is supported for tiled
formats. However it's better to fix this now rather than stumbling upon
it later.
Fixes: 80e8ae3b38 ("drm/msm/dpu: add support for wide planes")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601059/
Link: https://lore.kernel.org/r/20240627-dpu-virtual-wide-v5-3-5efb90cbb8be@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
YUV formats require only CSC to be enabled. Even decimated formats
should not require scaler. Relax the requirement and don't check for the
scaler block while checking if YUV format can be enabled.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/601049/
Link: https://lore.kernel.org/r/20240627-dpu-virtual-wide-v5-2-5efb90cbb8be@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Before re-starting link training reset the link phy params namely
the pre-emphasis and voltage swing levels otherwise the next
link training begins at the previously cached levels which can result
in link training failures.
Fixes: 8ede2ecc3e ("drm/msm/dp: Add DP compliance tests on Snapdragon Chipsets")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/605946/
Link: https://lore.kernel.org/r/20240725220450.131245-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
For cases where the crtc's connectors_changed was set without enable/active
getting toggled , there is an atomic_enable() call followed by an
atomic_disable() but without an atomic_mode_set().
This results in a NULL ptr access for the dpu_encoder_get_drm_fmt() call in
the atomic_enable() as the dpu_encoder's connector was cleared in the
atomic_disable() but not re-assigned as there was no atomic_mode_set() call.
Fix the NULL ptr access by moving the assignment for atomic_enable() and also
use drm_atomic_get_new_connector_for_encoder() to get the connector from
the atomic_state.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/59
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Patchwork: https://patchwork.freedesktop.org/patch/606729/
Link: https://lore.kernel.org/r/20240731191723.3050932-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
It was found that some hotplug operations may cause multiple
rebuild_sched_domains_locked() calls. Some of those intermediate calls
may use cpuset states not in the final correct form leading to incorrect
sched domain setting.
Fix this problem by using the existing force_rebuild flag to inhibit
immediate rebuild_sched_domains_locked() calls if set and only doing
one final call at the end. Also renaming the force_rebuild flag to
force_sd_rebuild to make its meaning for clear.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit e2ffe502ba ("cgroup/cpuset: Add cpuset.cpus.exclusive for
v2") adds a user writable cpuset.cpus.exclusive file for setting
exclusive CPUs to be used for the creation of partitions. Since then
effective_xcpus depends on both the cpuset.cpus and cpuset.cpus.exclusive
setting. If cpuset.cpus.exclusive is set, effective_xcpus will depend
only on cpuset.cpus.exclusive. When it is not set, effective_xcpus
will be set according to the cpuset.cpus value when the cpuset becomes
a valid partition root.
When cpuset.cpus is being cleared by the user, effective_xcpus should
only be cleared when cpuset.cpus.exclusive is not set. However, that
is not currently the case.
# cd /sys/fs/cgroup/
# mkdir test
# echo +cpuset > cgroup.subtree_control
# cd test
# echo 3 > cpuset.cpus.exclusive
# cat cpuset.cpus.exclusive.effective
3
# echo > cpuset.cpus
# cat cpuset.cpus.exclusive.effective // was cleared
Fix it by clearing effective_xcpus only if cpuset.cpus.exclusive is
not set.
Fixes: e2ffe502ba ("cgroup/cpuset: Add cpuset.cpus.exclusive for v2")
Cc: stable@vger.kernel.org # v6.7+
Reported-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix the dp_panel_get_supported_bpp() API to return the minimum
supported bpp correctly for relevant cases and use this API
to correct the behavior of DP driver which hard-codes the max supported
bpp to 30.
This is incorrect because the number of lanes and max data rate
supported by the lanes need to be taken into account.
Replace the hardcoded limit with the appropriate math which accounts
for the accurate number of lanes and max data rate.
changes in v2:
- Fix the dp_panel_get_supported_bpp() and use it
- Drop the max_t usage as dp_panel_get_supported_bpp() already
returns the min_bpp correctly now
changes in v3:
- replace min_t with just min as all params are u32
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/43
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/607073/
Link: https://lore.kernel.org/r/20240805202009.1120981-1-quic_abhinavk@quicinc.com
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
DPU debugging macros need to be converted to a proper drm_debug_*
macros, however this is a going an intrusive patch, not suitable for a
fix. Wire DPU_DEBUG and DPU_DEBUG_DRIVER to always use DRM_DEBUG_DRIVER
to make sure that DPU debugging messages always end up in the drm debug
messages and are controlled via the usual drm.debug mask.
I don't think that it is a good idea for a generic DPU_DEBUG macro to be
tied to DRM_UT_KMS. It is used to report a debug message from driver, so by
default it should go to the DRM_UT_DRIVER channel. While refactoring
debug macros later on we might end up with particular messages going to
ATOMIC or KMS, but DRIVER should be the default.
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/606932/
Link: https://lore.kernel.org/r/20240802-dpu-fix-wb-v2-2-7eac9eb8e895@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
The previous patch to fix the newfstatat() syscall entry ended up breaking
fstat() instead. Unfortunately these two are not handled the same way, so
I messed this one up the exact opposite way.
Fixes: 343416f0c1 ("syscalls: fix syscall macros for newfstat/newfstatat")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to the implementation of cgroup_css_set_fork(), it will fail
if cset cannot be found and the can_fork/cancel_fork methods will not
be called in this case, which means that the argument 'cset' for these
methods must not be NULL, so remove the unrechable paths in them.
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Case #1:
SQLite App GC Thread Kworker Shrinker
- f2fs_ioc_start_atomic_write
- f2fs_ioc_commit_atomic_write
- f2fs_commit_atomic_write
- filemap_write_and_wait_range
: write atomic_file's data to cow_inode
echo 3 > drop_caches
to drop atomic_file's
cache.
- f2fs_gc
- gc_data_segment
- move_data_page
- set_page_dirty
- writepages
- f2fs_do_write_data_page
: overwrite atomic_file's data
to cow_inode
- f2fs_down_write(&fi->i_gc_rwsem[WRITE])
- __f2fs_commit_atomic_write
- f2fs_up_write(&fi->i_gc_rwsem[WRITE])
Case #2:
SQLite App GC Thread Kworker
- f2fs_ioc_start_atomic_write
- __writeback_single_inode
- do_writepages
- f2fs_write_cache_pages
- f2fs_write_single_data_page
- f2fs_do_write_data_page
: write atomic_file's data to cow_inode
- f2fs_gc
- gc_data_segment
- move_data_page
- set_page_dirty
- writepages
- f2fs_do_write_data_page
: overwrite atomic_file's data to cow_inode
- f2fs_ioc_commit_atomic_write
In above cases racing in between atomic_write and GC, previous
data in atomic_file may be overwrited to cow_file, result in
data corruption.
This patch introduces PAGE_PRIVATE_ATOMIC_WRITE bit flag in page.private,
and use it to indicate that there is last dirty data in atomic file,
and the data should be writebacked into cow_file, if the flag is not
tagged in page, we should never write data across files.
Fixes: 3db1de0e58 ("f2fs: change the current atomic write way")
Cc: Daeho Jeong <daehojeong@google.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The macro stat_inc_cp_count accepts a parameter si,
but it was not used, rather the variable sbi was directly used,
which may be a local variable inside a function that calls the macros.
Signed-off-by: Julian Sun <sunjunchao2870@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The macro on_f2fs_build_free_nids accepts a parameter nmi,
but it was not used, rather the variable nm_i was directly used,
which may be a local variable inside a function that calls the macros.
Signed-off-by: Julian Sun <sunjunchao2870@gmail.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Currently, we are using a mix of traditional UFS and zone UFS to support
some functionalities that cannot be achieved on zone UFS alone. However,
there are some issues with this approach. There exists a significant
performance difference between traditional UFS and zone UFS. Under normal
usage, we prioritize writes to zone UFS. However, in critical conditions
(such as when the entire UFS is almost full), we cannot determine whether
data will be written to traditional UFS or zone UFS. This can lead to
significant performance fluctuations, which is not conducive to
development and testing. To address this, we have added an option
zlu_io_enable under sys with the following three modes:
1) zlu_io_enable == 0:Normal mode, prioritize writing to zone UFS;
2) zlu_io_enable == 1:Zone UFS only mode, only allow writing to zone UFS;
3) zlu_io_enable == 2:Traditional UFS priority mode, prioritize writing to
traditional UFS.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Wu Bo <bo.wu@vivo.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
While calculating the end addresses of main area and segment 0, u32
may be not enough to hold the result without the danger of int
overflow.
Just in case, play it safe and cast one of the operands to a
wider type (u64).
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: fd694733d5 ("f2fs: cover large section in sanity check of super")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When dealing with large extents and calculating file offsets by
summing up according extent offsets and lengths of unsigned int type,
one may encounter possible integer overflow if the values are
big enough.
Prevent this from happening by expanding one of the addends to
(pgoff_t) type.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: d323d005ac ("f2fs: support file defragment")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The result of multiplication between values derived from functions
dir_buckets() and bucket_blocks() *could* technically reach
2^30 * 2^2 = 2^32.
While unlikely to happen, it is prudent to ensure that it will not
lead to integer overflow. Thus, use mul_u32_u32() as it's more
appropriate to mitigate the issue.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 3843154598 ("f2fs: introduce large directory support")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Introudce a new help get_dnode_base() to wrap common code from
get_dnode_addr() and data_blkaddr() for cleanup.
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Fixes the register ID of SPSR_FIQ.
SPSR_FIQ is a 64-bit register and the 64-bit register size mask is
0x0030000000000000ULL.
Fixes: fd3bc912d3 ("KVM: Documentation: Document arm64 core registers in detail")
Signed-off-by: Takahiro Itazuri <itazur@amazon.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230606154628.95498-1-itazur@amazon.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Commit 5e5c50964e ("arm64: dts: ti: k3-j722s: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed a hole within gpio-range for main_pmx0. As a result, automatic
mapping of GPIO to pin control for gpios within the main_pmx0 domain is
broken. Fix this by correcting the gpio-range.
Fixes: 5e5c50964e ("arm64: dts: ti: k3-j722s: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-4-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed a hole within gpio-range for main_pmx0. As a result, automatic
mapping of GPIO to pin control for gpios within the main_pmx0 domain is
broken. Fix this by correcting the gpio-range.
Fixes: d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-3-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed introducing the range description for the mcu_gpio node. As a
result, automatic mapping of GPIO to pin control for mcu gpios is
broken. Fix this by introducing the proper ranges.
Fixes: d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-2-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
This is a preparation to support skipping empty events.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240803211332.1107222-5-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The annotation__pcnt_width() calculates the screen width for the
overhead (percent) area considering event groups properly. Use this
function consistently so that we can make sure it has similar output
in different modes. But there's a difference in stdio and tui output:
stdio uses 8 and tui uses 7 for a percent.
Let's use 8 and adjust the print width in __annotation_line__write()
properly.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240803211332.1107222-4-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We want to use it in different places so make sure it sets properly
in symbol__annotate() before creating the disasm lines.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240803211332.1107222-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The data_nr keeps the number of entries in al->data[] so it should use
it when it iterates the array. The notes->src->nr_events should have
the same number but it'd be natural to use al->data_nr.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/20240803211332.1107222-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jesse Taube <jesse@rivosinc.com> says:
Add functions to pi/fdt_early.c to help parse the FDT to check if
the isa string has the Zkr extension. Then use the Zkr extension to
seed the KASLR base address.
The first two patches fix the visibility of symbols.
* b4-shazam-merge:
RISC-V: Use Zkr to seed KASLR base address
RISC-V: pi: Add kernel/pi/pi.h
RISC-V: lib: Add pi aliases for string functions
RISC-V: pi: Force hidden visibility for all symbol references
Link: https://lore.kernel.org/r/20240709173937.510084-1-jesse@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Parse the device tree for Zkr in the isa string.
If Zkr is present, use it to seed the kernel base address.
On an ACPI system, as of this commit, there is no easy way to check if
Zkr is present. Blindly running the instruction isn't an option as;
we have to be able to trust the firmware.
Signed-off-by: Jesse Taube <jesse@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Tested-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240709173937.510084-5-jesse@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add pi.h header for declarations of the kernel/pi prefixed functions
and any other related declarations.
Suggested-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Jesse Taube <jesse@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240709173937.510084-4-jesse@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
memset, strcmp, and strncmp are all used in the __pi_ section,
add SYM_FUNC_ALIAS for them.
When KASAN is enabled in <asm/string.h> __pi___memset is also needed.
Suggested-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Jesse Taube <jesse@rivosinc.com>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240709173937.510084-3-jesse@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Eliminate all GOT entries in the .pi section, by forcing hidden
visibility for all symbol references, which informs the compiler that
such references will be resolved at link time without the need for
allocating GOT entries.
Include linux/hidden.h in Makefile, like arm64, for the
hidden visibility attribute.
Signed-off-by: Jesse Taube <jesse@rivosinc.com>
Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Link: https://lore.kernel.org/r/20240709173937.510084-2-jesse@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
An empty sysctl table entry was inadvertently left behind for observation
sysctl. The breaks on 6.11 with the following errors:
[ 219.654850] sysctl table check failed: dev/xe/(null) procname is null
[ 219.654862] sysctl table check failed: dev/xe/(null) No proc_handler
Drop the empty entry.
Fixes: 8169b2097d ("drm/xe/uapi: Rename xe perf layer as xe observation layer")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/2419
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240805062057.3547560-1-ashutosh.dixit@intel.com
Negate the values reported for the accelerometer z-axis in order to
match Documentation/devicetree/bindings/iio/mount-matrix.txt.
Fixes: 14a213dcb0 ("ARM: dts: n900: use iio driver for accelerometer")
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Reviewed-By: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20240722113137.3240847-1-absicsz@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The cyttsp4 touchscreen driver was contributed in 2013 and since then
has seen no updates. The driver uses platform data (no device tree
support) and there are no users of it in the mainline kernel. There were
occasional fixes to it for issues either found by static code analysis
tools or via visual inspection, but otherwise the driver is completely
untested.
Remove the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/ZrAZ2cUow_z838tp@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver does not try to power down the rails at system suspend or
when touchscreen is not in use, but rather enables regulators at probe
time. Power savings are achieved by requesting the controller to enter
low power mode.
Switch to devm_regulator_bulk_get_enable() instead of separately
requesting regulators, enabling them, and installing a custom
devm-action to disable them on unbind/remove, which simplifies the
code.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ZrAgj9rG6oVqfdoK@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver does not use legacy GPIO API, stop including this header.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ZrAaOu_vf-cVBhRn@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver does not use legacy GPIO API, stop including this header.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/ZrAaHWNvaAfDlDfI@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ensure that the touchscreen response has correct "report id" byte
before processing the touch data and discard other messages.
Fixes: 42370681bd ("Input: Add support for ILITEK Lego Series")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240805085511.43955-3-francesco@dolcini.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When built with W=1, the driver throws the following warning:
../drivers/bus/ti-sysc.c:169: warning: Excess struct member
'disable_on_idle' description in 'sysc'
Fix it by removing the excess description.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240805101118.427133-1-d-gole@ti.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use of_property_present() to test for property presence rather than
of_get_property(). This is part of a larger effort to remove callers
of of_get_property() and similar functions. of_get_property() leaks
the DT property data pointer which is a problem for dynamically
allocated nodes which may be freed.
The code was also incorrectly assigning the return value to a 'struct
property' pointer. It didn't matter as "prop" was never dereferenced.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240731191312.1710417-1-robh@kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For different reasons i2c transaction may fail or report id in the
message may be wrong. Avoid closing the frame in this case as it will
result in all contacts being dropped, indicating that nothing is
touching the screen anymore, while usually it is not the case.
Fixes: 42370681bd ("Input: Add support for ILITEK Lego Series")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240805085511.43955-2-francesco@dolcini.it
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The IP of QDMA ls1028/ls1043/ls1046/ is same as ls1021. So allow compatible
string fallback to fsl,ls1021a-qdma.
The difference is that ls1021a-qdma have 3 irqs, and other have 5 irqs.
Fix below CHECK_DTB warning.
arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dtb: dma-controller@8380000: compatible: ['fsl,ls1046a-qdma', 'fsl,ls1021a-qdma'] is too long
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240710145400.2257718-1-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Newer firmware allows to query touchpad resolution information by
reading from resolution register. Presence of resolution register is
signalled via bit 29 of the "register presence" register. On devices
that lack this resolution register we fall back to using pitch and
number of receivers data to calculate size of the sensor.
Signed-off-by: Marge Yang <marge.yang@tw.synaptics.com>
Signed-off-by: Vincent Huang <Vincent.Huang@tw.synaptics.com>
Link: https://lore.kernel.org/r/20240805083636.1381205-1-marge.yang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the late-read buffer in the CS35L56 SoundWire interface to
read OTP memory.
The OTP memory has a longer access latency than chip registers
and cannot guarantee to return the data value in the SoundWire
control response if the bus clock is >4.8 MHz. The Cirrus
SoundWire peripheral IP exposes the bridge-to-bus read buffer
and status bits. For a read from OTP the bridge status bits are
polled to wait for the OTP data to be loaded into the read buffer
and the data is then read from there.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e1830f66f6 ("ASoC: cs35l56: Add helper functions for amp calibration")
Link: https://patch.msgid.link/20240805140839.26042-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
