Add some logic for Spread Spectrum control. It is used in conjuncture
with SDM fractional dividers. SSC has to be disabled when we configure
the divider settings.
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a callback to the pll_params for custom dynamic ramping
functions which can be specified per PLL.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add logic which (if specified for a pll) can verify that a PLL is set
to the proper default value and if not can set it. This can be
specified per PLL as each will have different default values.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code makes use of the SDM fractional divider if present to
constrain the allowable programming range of the PLL divider register
bitfields to take advantage of higher frequency granularity that can
be induced by the SDM divider.
Based on original work by Aleksandr Frid <afrid@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 SoC's have 2 PLLs for memory usage. Add plumbing to register
and handle PLLMB.
PLLMB is used to allow switching between 2 PLLM's without having to use
and intermediate backup PLL, as we need to lock the PLL before we can
switch to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra210 SoC's, the logic to enable several of the plls is different
from previous generations. Therefore, add registration functions specific
to Tegra210 which will handle them appropriately.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
cppcheck picked up that there were a couple of missing va_end()
calls in functions using va_start().
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
rsrc-card is DPCM supported version of simple-card. Thus it has similar
DT format. OTOH, snd_soc_dai_link requests cpu/codec, but one of them
will be snd-soc-dummy in DPCM case, and DPCM requests frontend/backend
dai_link. This means it might have multi backend/codec.
And, SND_SOC_DAIFMT_xxx is based on "codec". Because of these
difference, current rsrc card can't detect correct dai_fmt.
This patch detect correct dai fmt from 1st "codec".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1efb53a220 ("ASoC: simple-card: Remove support for setting differing
DAI formats") removed set_fmt support from simple-card.
rsrc-card follows same style, because it is based on simple-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver will use tdm slot on TDM Multi Mode support.
This patch enables tdm slot on rsrc card driver on DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When power up, a "pop" is heard on line-in and mic-in.
An analysis of the PCM shows it lasts ~400ms
and looks like a filter response.
VAG power up should be delayed by 400ms as VAG power down is.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Older firmwares don't specify access flags for the controls,
unfortunately the usage of some of these firmware relies on being able
to read back values from the DSP. The current control code will only do
this for volatile controls. This patch will read the control from the
hardware if no flags are specified and the control is currently
enabled, which should cover these legacy use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When tearing down page tables, we return early for the final level
since we know that we won't have any table pointers to follow.
Unfortunately, this also means that we forget to free the final level,
so we end up leaking memory.
Fix the issue by always freeing the current level, but just don't bother
to iterate over the ptes if we're at the final level.
Cc: <stable@vger.kernel.org>
Reported-by: Zhang Bo <zhangbo_a@xiaomi.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It is ILLEGAL to set STE.S1STALLD to 1 if stage 1 is enabled and
either the stall or terminate models are not supported.
This patch fixes the STALLD check and ensures that we don't set STALLD
in the STE when it is not supported.
Signed-off-by: Prem Mallappa <pmallapp@broadcom.com>
[will: consistently use IDR0_STALL_MODEL_* prefix]
Signed-off-by: Will Deacon <will.deacon@arm.com>
When acknowledging global errors, the GERRORN register should be written
with the original GERROR value so that active errors are toggled.
This patch fixed the driver to write the original GERROR value to
GERRORN, instead of an active error mask.
Signed-off-by: Prem Mallappa <pmallapp@broadcom.com>
[will: reworked use of active bits and fixed commit log]
Signed-off-by: Will Deacon <will.deacon@arm.com>
There is no need to keep a useful accessor for a public structure hidden
away in a private implementation. Move it out alongside the structure
definition so that other implementations may reuse it.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When invalidating an IOVA range potentially spanning multiple pages,
such as when removing an entire intermediate-level table, we currently
only issue an invalidation for the first IOVA of that range. Since the
architecture specifies that address-based TLB maintenance operations
target a single entry, an SMMU could feasibly retain live entries for
subsequent pages within that unmapped range, which is not good.
Make sure we hit every possible entry by iterating over the whole range
at the granularity provided by the pagetable implementation.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: added missing semicolons...]
Signed-off-by: Will Deacon <will.deacon@arm.com>
IOMMU hardware with range-based TLB maintenance commands can work
happily with the iova and size arguments passed via the tlb_add_flush
callback, but for IOMMUs which require separate commands per entry in
the range, it is not straightforward to infer the necessary granularity
when it comes to issuing the actual commands.
Add an additional argument indicating the granularity for the benefit
of drivers needing to know, and update the ARM LPAE code appropriately
(for non-leaf invalidations we currently just assume the worst-case
page granularity rather than walking the table to check).
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the case of corrupted page tables, or when an invalid size is given,
__arm_lpae_unmap() may recurse beyond the maximum number of levels.
Unfortunately the detection of this error condition only happens *after*
calculating a nonsense offset from something which might not be a valid
table pointer and dereferencing that to see if it is a valid PTE.
Make things a little more robust by checking the level is valid before
doing anything which depends on it being so.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Whilst the architecture only defines a few of the possible CERROR values,
we should handle unknown values gracefully rather than go out of bounds
trying to print out an error description.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The basic flow for add a device:
arm_smmu_add_device
|->iommu_group_get_for_dev
|->iommu_group_get
return group; (1)
|->ops->device_group : Init/increase reference count to/by 1.
|->iommu_group_add_device : Increase reference count by 1.
return group (2)
|->return 0;
Since we are adding one device, the flow is (2) and the group reference
count will be increased by 2. So, we need to add iommu_group_put at the
end of arm_smmu_add_device to decrease the count by 1.
Also take the failure path into consideration when fail to add a device.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When we initialise a bypass STE, we memset the structure to zero and
set the Valid and Config fields to indicate that the stream should
bypass the SMMU. Unfortunately, this results in an SHCFG field of 0
which means that the shareability of any incoming transactions is
overridden with non-shareable, leading to potential coherence problems
down the line.
This patch fixes the issue by initialising bypass STEs to use the
incoming shareability attributes. When translation is in effect at
either stage 1 or stage 2, the shareability is determined by the
page tables.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The free_io_pgtable_ops() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM SMMUv3 driver uses dma_{alloc,free}_coherent to manage its
queues and configuration data structures.
This patch converts the driver to the managed (dmam_*) API, so that
resources are freed automatically on device teardown. This greatly
simplifies the failure paths and allows us to remove a bunch of
handcrafted freeing code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
PRIQ_0_OF has been removed from the SMMUv3 architecture, so remove its
corresponding (and unused) #define from the driver.
Signed-off-by: Will Deacon <will.deacon@arm.com>
AZX_DCAPS_POSFIX_VIA is coupled always with AZX_DRIVER_VIA type, so we
don't have to keep this bit in dcaps. Save one more!
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AZX_DCAPS_RIRB_DELAY is dedicated only for Nvidia and its purpose is
just to set a flag in bus. So it's better to be set in the toplevel
driver, either hda_intel.c or hda_tegra.c, instead of the common
hda_controller.c. This also allows us to strip this flag from dcaps,
so save one more bit there.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By default DISPC asserts hsync and vsync sequentially, i.e. there's
first hsync and that is immediately followed by vsync. This is the only
available behaviour on OMAP2/3, and default behaviour on OMAP4+.
OMAP4+ has ALIGN bit in POL_FREQ register, which makes DISPC assert both
syncs at the same time.
It has been observed that some panels don't like sequential syncs (AM5
EVM's panel). After studying the datasheets for multiple panels and
encoders, and MIPI DPI spec, it looks like there is no standard way to
handle this.
Sometimes the datasheets don't mention the required syncs behaviour at
all, sometimes the datasheets have images that hint towards simultaneous
syncs, and sometimes it is explicitly mentioned that simultaneous syncs
are needed. No panels or encoders requiring sequential sync was found.
It thus seems to be safe to default to simultaneous syncs when the ALIGN
bit is available. This fixed AM5 EVM's panel, and no side effects have
been observed on other panels or encoders.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Update omapdss driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enable new kernel cpu hotplug functionality by allowing cpu dlpar requests
to be initiated from sysfs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the ability to hotplug add cpus via rtas hotplug events by either
specifying the drc index of the CPU to add, or providing a count of the
number of CPUs to add.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the ability to dlpar remove CPUs via hotplug rtas events, either by
specifying the drc-index of the CPU to remove or providing a count of cpus
to remove.
To remove multiple cpus in a single request we create a list of possible
DR (Dynamic Reconfiguration) cpus and their drc indexes that can be
removed. We can then traverse the list remove each cpu and easily clean
up in any cases of failure.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update the cpu dlpar add/remove paths to do better error recovery when
a failure occurs during the add/remove operation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Re-factor the cpu hotplug code to support doing cpu hotplug completely in
the kernel and using the existing sysfs probe/release interfaces. This
patch pulls out pieces of existing cpu hotplug code into common routines,
dlpar_cpu_add() and dlpar_cpu_remove(), to be used by both interfaces.
There are no functional changes introduced.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functional changes, this patch is simply a move of the cpu hotplug
code from pseries/dlpar.c to pseries/hotplug-cpu.c. This is in an effort
to consolidate all of the cpu hotplug code in a common place.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When DLPAR adding a CPU we should verify that the CPU does not already
exist. Failure to do so can generate a kernel oops;
[ 9.465585] kernel BUG at arch/powerpc/platforms/pseries/dlpar.c:382!
[ 9.465796] Oops: Exception in kernel mode, sig: 5 [#1]
This oops can be generated by causing a probe to be performed on a cpu
by writing to the sysfs cpu probe file (/sys/devices/system/cpu/probe).
This patch adds a check for the existence of cpu prior to probing the cpu
so userspace doing the wrong thing won't trigger a BUG_ON().
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PPC476FPE has a different PVR from previous PPC476 processors. The
kexec code checks the PVR in order to correctly setup the MMU. When
the initial support for 476FPE processors was added the corresponding
change in the kexec code was missed. This patch simply adds the check
and solves the following bug on kexec:
kexec: Starting new kernel
Bye!
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0xee9a50f8
cpu 0x0: Vector: 400 (Instruction Access) at [ee9d7d20]
pc: ee9a50f8
lr: ee9a50e4
sp: ee9d7dd0
msr: 21020
current = 0xee40f000
pid = 960, comm = kexec
enter ? for help
[link register ] ee9a50e4
[ee9d7dd0] c0013748 default_machine_kexec+0x58/0x70 (unreliable)
[ee9d7df0] c0012f04 machine_kexec+0x34/0x40
[ee9d7e00] c00aa1ec kernel_kexec+0x9c/0xb0
[ee9d7e20] c005d704 SyS_reboot+0x1f4/0x220
[ee9d7f40] c000db68 ret_from_syscall+0x0/0x3c
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
NVLink is a high speed interconnect that is used in conjunction with a
PCI-E connection to create an interface between CPU and GPU that
provides very high data bandwidth. A PCI-E connection to a GPU is used
as the control path to initiate and report status of large data
transfers sent via the NVLink.
On IBM Power systems the NVLink processing unit (NPU) is similar to
the existing PHB3. This patch adds support for a new NPU PHB type. DMA
operations on the NPU are not supported as this patch sets the TCE
translation tables to be the same as the related GPU PCIe device for
each NVLink. Therefore all DMA operations are setup and controlled via
the PCIe device.
EEH is not presently supported for the NPU devices, although it may be
added in future.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move __raw_rm_writeq() from platforms/powernv/pci-ioda.c to
include/asm/io.h so that it can be used by other code.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit removed the pcidev field from struct pci_dn as it was no
longer in use by the kernel. However to support finding the
association of Nvlink devices to GPU devices from the device-tree this
field is required.
This reverts commit 250c7b277c ("powerpc/pci: Remove unused struct
pci_dn.pcidev field").
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The name of PCI root bus's M64 resource isn't initialized properly.
When dumping "/proc/iomem", "<BAD>" is seen for those M64 resources
on PCI root buses.
~# cat /proc/iomem | grep -e "BAD"
3b0000000000-3b0fefffffff : <BAD>
3b1000000000-3b1fefffffff : <BAD>
3c0000000000-3c0fefffffff : <BAD>
3c1000000000-3c1fefffffff : <BAD>
3c2000000000-3c2fefffffff : <BAD>
This fixes the issue by setting the name of PCI root bus's M64
resource to that of PHB's device node full name. With the patch,
no "<BAD>" is seen from "/proc/iomem".
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
User space checkpoint and restart tool (CRIU) needs the page's change
to be soft tracked. This allows to do a pre checkpoint and then dump
only touched pages.
This is done by using a newly assigned PTE bit (_PAGE_SOFT_DIRTY) when
the page is backed in memory, and a new _PAGE_SWP_SOFT_DIRTY bit when
the page is swapped out.
To introduce a new PTE _PAGE_SOFT_DIRTY bit value common to hash 4k
and hash 64k pte, the bits already defined in hash-*4k.h should be
shifted left by one.
The _PAGE_SWP_SOFT_DIRTY bit is dynamically put after the swap type in
the swap pte. A check is added to ensure that the bit is not
overwritten by _PAGE_HPTEFLAGS.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
CC: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The STD_EXCEPTION_PSERIES macro takes both a vector number, and a
location (memory address). However both are always identical, so combine
them to save repeating ourselves.
This does mean an exception handler must always exist at the location in
memory that matches its vector number. But that's OK because this is the
"STD" macro (standard), which does exactly that. We have other macros
for the other cases, eg. STD_EXCEPTION_PSERIES_OOL (out of line).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HMT_MEDIUM_PPR_DISCARD is a macro which is present at the start of most
of our first level exception handlers. It conditionally executes a
HMT_MEDIUM instruction, which sets the processor priority to medium.
On on modern systems, ie. Power7 and later, it is nop'ed out at boot.
All it does is make the exception vectors more cramped, and consume 4
bytes of icache.
On old systems it has the effect of boosting the processor priority at
the start of exception processing. If we were previously in the idle
loop for example, we may be at low or very low priority. This is
desirable as we want to process the exception as fast as possible.
However looking closely at the generated code, we see that in all cases
we execute another HMT_MEDIUM just four instructions later. With code
patching applied, the final code on an old (Power6) system will look
like, eg:
c000000000000300 <data_access_pSeries>:
c000000000000300: 7c 42 13 78 mr r2,r2 <-
c000000000000304: 7d b2 43 a6 mtsprg 2,r13
c000000000000308: 7d b1 42 a6 mfsprg r13,1
c00000000000030c: f9 2d 00 80 std r9,128(r13)
c000000000000310: 60 00 00 00 nop
c000000000000314: 7c 42 13 78 mr r2,r2 <-
So I suggest that the added code complexity of HMT_MEDIUM_PPR_DISCARD is
not justified by the benefit of boosting the processor priority for the
duration of four instructions, and therefore we drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any users of enter_rtas() outside of rtas.c, so make
it "private", by moving the declaration inside rtas.c. Hopefully this
will encourage people to use one of the wrappers which takes the sharp
edges off the RTAS calling sequence.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although call_rtas_display_status() does actually want to use the
regular RTAS locking, it doesn't want the extra logic that is in
rtas_call(), so currently it open codes the logic.
Instead we can use rtas_call_unlocked(), after taking the RTAS lock.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
