dwmac4 has multiple banks of perfect filter entries, independently
configurable during IP integration.
The multi_addr bank reports a number between 0 and 31 corresponding to
the actual number of entries in that bank, while the 32 and 64 banks
are all-or-nothing.
Expose these caps over debugfs as well.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Link: https://patch.msgid.link/20260831070121.349778-2-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
David Yang says:
====================
net: dsa: motorcomm: Add LED support
LEDs can be described in the device tree using the standard LED node
notation. Currently, only parallel mode and strict 1:1 mapping (i.e. the
HW default) are supported.
====================
Link: https://patch.msgid.link/20260831044818.4103477-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add LEDs definition example for yt921x to describe how they should be
defined for a correct usage.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260831044818.4103477-6-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Each port has at most 3 LEDs connected and can be declared using the
standard LEDs structure.
Currently, only parallel mode and strict 1:1 mapping (i.e. the HW
default) are supported.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831044818.4103477-5-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SMI operations are going to be used across different modules. Minor
changes are applied to fix build errors.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831044818.4103477-4-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
yt921x is already the longest single-file DSA driver, so it's time to
split it into parts.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831044818.4103477-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mutex_is_locked() was used to check the lock status. While it should not
be triggered unless a bug is introduced, it does not warn on lock being
held by another thread. Fix it with lockdep helpers.
Fixes: 186623f4aa ("net: dsa: yt921x: Add support for Motorcomm YT921x")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831044818.4103477-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 03b4702fc5 ("net: phy: air_en8811h: move LED GPIO
configuration to config_init") moved the EN8811H LED GPIO setup from
probe to config_init because an MD32 restart clears the output-enable
bits.
AN8811HB follows the same initialization sequence: an8811hb_probe()
enables GPIO3/4/5, and later config_init() calls restart MD32.
Move the AN8811HB GPIO setup to the end of an8811hb_config_init(),
matching the current EN8811H path.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyou Xu <xuziyougm@gmail.com>
Link: https://patch.msgid.link/20260829033844.1975-1-xuziyougm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
dev->flags are not technically ops lock protected. The IFF_UP flag
will not change when dev->lock is held, but other flags may change
so KCSAN would probably not be impressed. Because of this we added
a dedicated dev->up which is safe to read under dev->lock.
qstats want to make sure device is up, use dev->up.
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Reviewed-by: Joe Damato <joe@dama.to>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260831164159.1124679-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netdev_nl_queue_fill_lease() returns ENOMEM on nla_put failures.
This is wrong, the error code should be EMSGSIZE. But it doesn't
matter, caller of netdev_nl_queue_fill_lease() just checks if
the retcode is zero or not, and uses EMSGSIZE.
Reviewed-by: Joe Damato <joe@dama.to>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Bobby Eshleman <bobbyeshleman@meta.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20260831164159.1124679-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Lynx PCS never supported 25GBASE-R. Add it, so that a 25G DPMAC on
LX2160A can be driven by phylink.
The SerDes side had the mode since the commit
1cab8fba50 ("phy: lynx-28g: add support for 25GBASER")
and dpaa2-mac maps DPMAC_ETH_IF_CAUI to PHY_INTERFACE_MODE_25GBASER,
but the PCS never handled it, so phylink_validate() failed with the
interface.
25GBASE-R is a serial mode without clause-37 in-band autonegotiation,
exactly like 10GBASE-R: it does not needs any configuration, its state
is read with phylink_mii_c45_pcs_get_state(), and it reports
LINK_INBAND_DISABLE.
phylink_mii_c45_pcs_get_state() is extended in the same patch because
without it the link comes up reporting Unknown/Unknown.
Suggested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Co-developed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20260922-for-upstream-lynx-25gbaser-v1-v2-1-1e6cf79c7b52@free.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Golle says:
====================
net: dsa: mt7530: modernise register access and add two DSA ops
The mt7530 driver carries its own register accessors that predate the
regmap conversion and now largely duplicate what regmap already
provides, including locking. Most of this series removes that layer.
It first moves the MDIO bus locking into the switch regmap via
.lock/.unlock callbacks, matching the PCS regmaps, so any path reaching
the regmap is serialised automatically. With the wrappers no longer
adding locking, the thin mt7530_mii_* indirection is folded away and the
remaining accessors are replaced mechanically with the plain regmap API,
using the coccinelle semantic patches included in the commit messages.
The two remaining reset polls are converted to
regmap_read_poll_timeout() and the then-unused dummy poll machinery is
dropped. Open-coded register fields are converted to
FIELD_GET/FIELD_PREP. None of this is intended to change behaviour.
The last two patches implement .port_fast_age, which flushes dynamically
learned MAC entries on topology changes, and .port_change_conduit, which
moves a user port's CPU-port affinity at runtime.
The swallowed MDIO errors Sashiko flagged on v4 5/8 have meanwhile been
fixed in tree by "fix swallowed MDIO read errors" and "fix remaining
swallowed MDIO access errors", both merged into net-next. This respin is
rebased on top of them: regmap_* return values are no longer ignored,
which is what most of the semantic patches had to be reworked for.
====================
Link: https://patch.msgid.link/cover.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow changing the CPU port affinity of user ports at runtime via the
IFLA_DSA_CONDUIT netlink attribute. This updates the port matrix to
forward to the new CPU port instead of the old one.
Limit the operation to MT7531. There, trapped link-local frames follow
the per-port affinity, as the MT7531_CPU_PMAP destination mask is
further restricted by the port matrix. A conduit change is hence fully
honoured by the hardware, for regular traffic as well as for trapped
frames.
The MT7530 switch, including the variant embedded in the MT7621 SoC,
instead traps frames to the single CPU port set in the CPU_PORT field
of the MFC register, regardless of the affinity of the inbound user
port. With user ports affine to different CPU ports there is no
correct value for that field, so per-port CPU affinity cannot be fully
implemented for trapped frames. Routing a WAN port via the second SoC
GMAC is conventionally covered by the PHY muxing feature on these
switches, which bypasses the switch fabric and does not involve a CPU
port at all.
The switches on the MT7988, EN7581, AN7583 and EN7528 SoCs only have a
single CPU port, leaving no other conduit to change to.
As the op lives in the shared mt7530_switch_ops, populate the extack
when rejecting the unsupported variants instead of returning a bare
-EOPNOTSUPP. Also reject a conduit that belongs to a different switch
in the tree, whose port index has no meaning in the local port matrix.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/cfc6a478a384a7f309f08d9f76be8fd029c1f202.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the .port_fast_age DSA operation by flushing all non-static
(dynamically learned) MAC address entries from the address table.
The switch does not offer a combined "non-static AND per-port" match
mode, so the flush is global and the port argument is not used. Unlike
b53 and realtek, which flush the dynamic entries of the affected port
only, an STP topology change on one port therefore also flushes the
dynamically learned entries of the other ports; they are quickly
relearned.
Access the address table control register under priv->reg_mutex, as done
by all other ATC users (FDB and MDB add/del/dump), to serialise the
write-then-poll command sequence, and log a message should the command
fail.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/60f83ade0e371dfe2d974d5d192056935c3ab5c9.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use FIELD_GET and FIELD_PREP instead of open-coding register fields.
Replace 0x1f constant with (PHY_MAX_ADDR - 1).
Some field macros (ATC_HASH, VTCR_VID and STAG_VPID) were previously
defined as object-like macros referencing an undeclared 'x' and were
therefore unusable; convert them into proper FIELD_PREP() accessors.
The masks are equivalent to the open-coded values they replace, with
one exception: mt7530_vlan_cmd() now masks vid through VTCR_VID(vid)
instead of OR-ing it in raw, guarding the adjacent VTCR_FUNC field
against any bits set above the 12-bit VID width. VLAN IDs are always
in 0-4094, so this is a no-op in practice; it is a real hardening
rather than a strictly equivalent mechanical substitution.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/bd4eaf10fb6aa7a1bd056514b61b4481175708a5.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the two remaining switch reset polls to
regmap_read_poll_timeout() and remove struct mt7530_dummy_poll,
INIT_MT7530_DUMMY_POLL() and the mt7530_mii_poll() helper. As with the
command polls addressed by the preceding fixes, a failed read now
terminates the poll with an error instead of being fed to the loop
condition as a zero value.
Generated using the following semantic patch, plus removal of the two
now-unused definitions from mt7530.h:
// Poll the register through regmap so a failed read ends the poll.
@@
expression priv, reg;
identifier p, ret, val;
@@
- INIT_MT7530_DUMMY_POLL(&p, priv, reg);
- ret = readx_poll_timeout(mt7530_mii_poll, &p, val, val != 0,
- 20, 1000000);
+ ret = regmap_read_poll_timeout(priv->regmap, reg, val, val != 0,
+ 20, 1000000);
@@
identifier p;
@@
- struct mt7530_dummy_poll p;
... when != p
@@
identifier p;
type T;
@@
-static T mt7530_mii_poll(struct mt7530_dummy_poll *p) { ... }
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/609dcd8dd0c335e36bbc8df41413da58af1dbfb4.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace all mt7530_read() calls with direct regmap_read() calls and
remove the wrapper function. The wrapper returned 0 on failed reads;
preserve that behaviour by zeroing the read-back buffer at the start of
mt7530_regmap_read(), so callers that do not check the return code keep
seeing a deterministic value. The WARN_ON_ONCE error logging is dropped.
Most callsites follow the val = mt7530_read(priv, reg) pattern and are
converted mechanically using the following semantic patch:
@@
expression priv, reg;
identifier val;
@@
-val = mt7530_read(priv, reg);
+regmap_read(priv->regmap, reg, &val);
Remaining inline uses are converted by hand.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/a1dc338ae368554ec6faa974df7ba6f3660ae12b.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace all mt7530_rmw() calls with regmap_update_bits(), mt7530_set()
with regmap_set_bits(), and mt7530_clear() with regmap_clear_bits().
Remove the wrapper function definitions.
Generated using the following semantic patch:
@@
expression priv, reg, mask, set;
@@
-mt7530_rmw(priv, reg, mask, set)
+regmap_update_bits(priv->regmap, reg, mask, set)
@@
expression priv, reg, val;
@@
-mt7530_set(priv, reg, val)
+regmap_set_bits(priv->regmap, reg, val)
@@
expression priv, reg, val;
@@
-mt7530_clear(priv, reg, val)
+regmap_clear_bits(priv->regmap, reg, val)
Six regmap_update_bits() call sites with multi-line masks are rewrapped
by hand afterwards, as spatch joins their argument lines.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/182be19b483e77eb1d4ed835813359a27acd8e9c.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace all mt7530_write() calls with direct regmap_write() calls
and remove the wrapper function. The per-call error logging is
dropped -- regmap has its own tracing infrastructure.
Generated using the following semantic patch:
@@
expression priv, reg, val;
@@
-mt7530_write(priv, reg, val)
+regmap_write(priv->regmap, reg, val)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/fbb6ee8860fa60326a8af132ed114555e7163350.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With the lock wrappers removed in the previous commit, mt7530_write()
was a trivial wrapper around mt7530_mii_write(), and mt7530_read()
around mt7530_mii_read() via _mt7530_read(). Fold the function bodies
and eliminate the intermediate functions.
The _mt7530_read() poll helper for readx_poll_timeout() is renamed to
mt7530_mii_poll() and calls mt7530_read().
Callers are updated using the following semantic patch:
@@
expression E1, E2, E3;
@@
-mt7530_mii_write(E1, E2, E3)
+mt7530_write(E1, E2, E3)
@@
expression E1, E2;
@@
-mt7530_mii_read(E1, E2)
+mt7530_read(E1, E2)
@@
expression list args;
@@
-readx_poll_timeout(_mt7530_read, args)
+readx_poll_timeout(mt7530_mii_poll, args)
The two readx_poll_timeout() call sites keep their original line
wrapping, which spatch reflows for the longer helper name.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/591c4e7ff5b1b6d39aac7f0f04eb67f36f40d8a2.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch register regmap was created with .disable_locking = true,
relying on callers to manually lock the MDIO bus. Move the locking
into the regmap using .lock/.unlock callbacks, matching the PCS
regmaps that already do this. This allows any code path reaching the
regmap to be automatically protected.
With regmap handling bus locking, the manual mt7530_mutex_lock/unlock
calls in mt7530_write(), _mt7530_read(), mt7530_rmw() and
mt7530_port_change_mtu() become redundant and are removed, as is the
bus lock held across the ATC/VTCR command poll sequences.
The handle_mask_sync callback added by commit dd52b3df25 ("net: dsa:
mt7530: serialize the regmap IRQ chip like every other user") to hold
mt7530_mutex_lock() around the regmap-irq mask register write is
likewise removed. With the regmap now self-locking, regmap-irq's
default unmask_base sync is serialized on its own, and so are the
status read, ack write and init_ack_masked write that had no hook,
closing the gaps that commit left open. The per-device copy of the irq
chip it needed goes away too.
The MT7531 indirect PHY access functions need serialization of their
multi-step register sequences, but no longer need to hold bus->mdio_lock
across the whole operation. Switch them to reg_mutex.
core_write()/core_rmw() are the only remaining callers of
mt7530_mutex_lock(). They access TRGMII core PHY registers via the
clause 22 MMD indirect protocol -- a separate register space that
bypasses regmap and needs manual bus->mdio_lock protection.
The lock removals are generated using the following semantic patch:
// Collapse mt7530_write() now that regmap serialises bus access.
@@
expression priv, reg, val;
identifier ret;
@@
{
- int ret;
-
- mt7530_mutex_lock(priv);
-
- ret = mt7530_mii_write(priv, reg, val);
-
- mt7530_mutex_unlock(priv);
-
- return ret;
+ return mt7530_mii_write(priv, reg, val);
}
// Remove mt7530_mutex_lock/unlock around single regmap-based calls.
@@
expression priv, reg, mask, set;
@@
{
- mt7530_mutex_lock(priv);
-
regmap_update_bits(priv->regmap, reg, mask, set);
-
- mt7530_mutex_unlock(priv);
}
@@
expression p;
identifier val;
@@
{
- u32 val;
- mt7530_mutex_lock(p->priv);
- val = mt7530_mii_read(p->priv, p->reg);
- mt7530_mutex_unlock(p->priv);
- return val;
+ return mt7530_mii_read(p->priv, p->reg);
}
@@
expression priv;
identifier val;
@@
- mt7530_mutex_lock(priv);
val = mt7530_mii_read(priv, MT7530_GMACCR);
...
mt7530_mii_write(priv, MT7530_GMACCR, val);
- mt7530_mutex_unlock(priv);
// The ATC/VTCR command polls no longer need the bus lock held across
// the poll and the status read-back.
@@
expression priv, reg, cond;
identifier ret, val;
@@
- mt7530_mutex_lock(priv);
-
ret = regmap_read_poll_timeout(priv->regmap, reg, val, cond, 20, 20000);
if (!ret)
ret = regmap_read(priv->regmap, reg, &val);
-
- mt7530_mutex_unlock(priv);
// The MT7531 indirect PHY sequences keep serialising themselves, but
// against reg_mutex rather than the MDIO bus lock.
@@
expression priv;
identifier ret, val;
@@
- mt7530_mutex_lock(priv);
+ mutex_lock(&priv->reg_mutex);
ret = regmap_read_poll_timeout(priv->regmap, MT7531_PHY_IAC, val, ...);
@@
expression priv;
@@
out:
- mt7530_mutex_unlock(priv);
+ mutex_unlock(&priv->reg_mutex);
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/6927a774b87238800de5d6c0c717b0afd02d320b.1788190568.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Markus Stockhausen says:
====================
net: mdio: realtek-rtl9300: Add RTL83xx support
The Realtek Otto switch platform consists of four different series
- RTL838x aka maple : 28 port 1G Switches
- RTL839x aka cypress : 52 port 1G Switches
- RTL930x aka longan : 28 port 1G/2.5G/10G Switches
- RTL931x aka mango : 56 port 1G/2.5G/10G Switches
While the MDIO hardware polling unit and its necessity for the MAC
layer was always well known, no detailed documentation was available.
For this series the MDIO bus was inspected with a logic analyzer for
a better understanding how polling and kernel access interact on the
bus. All this will be explained now in the driver comments.
This patch series adds support for the RTL83xx devices. For this
- Enhance device tree binding.
- Add special handling for limitations enforced by hardware polling.
These already have minor side effects on RTL93xx devices but are even
more critical for the RTL83xx hardware.
- Add RTL83xx coding.
====================
Link: https://patch.msgid.link/20260831143439.2404484-1-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Realtek MDIO driver has been enhanced to support multiple
devices from the RTL83xx/RTL93xx series. Reword Kconfig and
module description accordingly.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-14-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIO driver has been prepared for multiple device support. Add all
required bits for the RTL839x (aka cypress) series. This is straightforward
but some things are worth mentioning.
- The device has a lot in common with the RTL931x series. It has 8192
(Realtek) pages and 7 MMIO registers.
- There are two SMI buses for 1G PHYs. Neither the bus nor address map
registers exist.
- The hardware has not much to configure. So the setup_controller()
function is not needed.
- The bit specific registers (polling & port_mask) are 2x32 bit wide. The
ports 0..31 got to <reg> and the ports 32..51 go to <reg+4>.
- C22 read/write functions must be called with PARK_PAGE = 0. Keep code
clean and avoid setting it to zero, matching the behavior of the RTL9310
logic.
- As per SDK the broadcast register allows to write to multiple ports
at the same time. Unlike RTL9310 where this is filled with a bit mask
for the current port RTL8390 does not use it for normal reads/writes.
It is simply set to 0 like the SDK does.
- The SDK fills the EXT_PAGE register with 0x1ff for C22 access and with
0x0 for C45 access. The reason for this is currently unknown and a
meaningful name can not be given. Align the driver coding with the
RTL9300_PHY_CTRL_PARK_PAGE settings and simply fill the hardcoded value.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-13-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MDIO driver has been prepared for multiple device support. Add all
required bits for the RTL838x (aka maple) series. This is straightforward
but some things are worth mentioning.
- The device has a lot in common with the RTL930x series. It has 28 ports,
4096 (Realtek) pages and 4 MMIO registers. With this a lot of the
existing RTL9300 defines could be reused. But to avoid confusion and
for better readability duplicate the defines with a proper prefix.
- The MDIO engine has no fail bit. Thus the mask is set to zero.
- There is only one SMI bus for 1G PHYs. No bus_map_base register exists.
- The setup_controller() function needs no C45 configuration as polling
only works in C22 mode
- The PHY access must be activated by a special register flag.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-12-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL838x devices with 28 ports produce PHY access timeout errors during
one of three boots while waiting for MDIO command completion. This is
currently set to 1ms.
Background: Access to the Realtek Otto ethernet MDIO bus must wait for
a free slot between two hardware polls. The polling sequence consists
of at least 17 commands on the RTL838x devices. This delay can be nicely
seen when disabling polling completely. The following times are measured
on a bus running on the default 2.5MHz. Time measured is from the last
register write that sets the command-start-bit until the hardware
responds with the command-finished-bit set.
- average c22 read with polling enabled on all ports: ~380us
- average c22 read with polling enabled on one port: ~380us
- average c22 read with polling completely disabled: ~180us
For this bus frequency the bare hardware runtime for a single command
(32 bit preamble + 32 bit data) is ~25us. So the hardware adds quite
some overhead. On top of this comes the fact that the RTL838x devices
are low on resources (500Mhz 4Kec core with 16K cache).
Increase the timeout to 10ms to be on the safe side.
Remark! In a future patch the bus clock frequency will be made
configurable with a minimum frequency of 1.25MHz. Setting this
(e.g. for debugging purposes) doubles the command run times but
will safely stay below 10ms.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-10-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware polling unit of the Realtek switches has a very special
handling for c22 PHY register 31 (aka Realtek page register) in place.
- On the RTL838x it is permanently reset to zero.
- On other devices there is some magic saving/restoring (aka parking)
in the background in place.
This makes access to PHYs a gamble.
It is vital to keep the polling alive so the MAC layer can rely on
consistent data. Intercept access to c22 register 31 and handle it
internally. Store the desired value for each port in the driver. When
issuing hardware access to other registers add the page to the command
towards the controller. Given this, the hardware will run two c22
commands that are not interrupted by polling.
... hardware poll ...
phy_write(phy, 31, page)
phy_write(phy, reg, value)
... hardware poll ...
Looking at this implementation one might argue that disabling/enabling
polling might be a cleaner solution. But one must remember that
- This driver differentiates clearly between C22 and C45 buses. During
probing it enables only one of the protocols for a bus.
- All known devices run RTL8218 (B/D/E) or RTL8214FC on 1G
- RTL839x gives link flapping when deactivating polling for a port
So a solution for a Realtek-only ecosystem is required. This commit
copies the downstream-proven driver-only page handling patch without
any new MDIO callbacks and is the lowest common denominator. If a
non-Realtek PHY is identified on a c22 bus the attachment aborts. It
should be noted that bus scan runs with the page handling already in
place before the check in notify_phy_attach(). This is accepted for
now.
Remark: To keep this simple, writes to register 31 are only accepted
if they are lower than the device specific raw page - 0..4094/8190.
Otherwise -EINVAL is returned. Under the above assumption (Only 1G
Realtek PHYs on a c22 bus) this is no limitation.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-9-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During PHY probing and configuration complex configuration sequences
might be issued and firmware might be loaded. Hardware polling can
interfere badly with that. E.g. a hardware polling MMD c45 over c22
request might break an ongoing firmware loading sequence.
To avoid such issues the polling of the Realtek Otto switches can be
(de)activated with one or two 32 bit mask registers. Each bit enables
(=1) or disables (=0) the polling of the corresponding port. Make use
of this as follows:
- Disable polling for all ports when the MDIO driver starts.
- Reenable polling just after the PHY has been attached.
- Disable polling just before the PHY is being detached.
This synchronizes the kernel and hardware polling to some extent. It
gracefully handles deferred probing of PHYs in case the driver is
loaded asynchronously during boot. Additionally it brings the hardware
polling into a consistent operation mode for devices where U-Boot does
not take care.
Important notes about the implementation:
Realtek is very inconsistent about its register naming. RTL930x uses
SMI_POLL_CTRL for polling control while it is SMI_PORT_POLLING_CTRL
on RTL931x. Keep these vendor names.
These devices do not support power management for the whole system.
So mdio_bus_phy_resume() is not used and it is not required to
disable/enable hardware polling for that usecase.
These devices have no CPU MAC to PHY design. Thus abort phy_attach()
in case PHYs are not mapped to valid switch ports. All MDIO bus
commands will fail afterwards, leaving it in an unusable state.
Enabling/disabling hardware polling is a simple regmap bit access.
For this it is enough to rely on the regmap internal lock.
This polling enabling/disabling does not solve the current inability
of the driver to handle C45-over-C22 access during normal operation.
For all existing designs this is not needed.
[1] https://github.com/openwrt/openwrt/blob/main/target/linux/realtek/files-6.18/drivers/net/mdio/mdio-realtek-otto.c#L818
[2] https://lore.kernel.org/netdev/680696024a8648535ce6dee771fe4de67802e0e8.1769053496.git.daniel@makrotopia.org/
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-8-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Realtek MDIO driver relies on devm managed resources for lifetime
management and allocates its internal central controller structure
otto_emdio_priv via devm_kzalloc(). This can lead to a use-after-free
in the following sitauation:
- If the driver is removed or unbound via sysfs the controller devm
cleanup is triggered immediately. A corrupt devicetree might produce
a load failure and a cleanup too.
- However the MDIO buses are allocated with devm_mdiobus_alloc_size()
and are reference counted. So if a MAC driver still holds a reference
to a PHY device on the bus, the mii_bus will remain alive.
- Any action that is run for the buses afterwards still relies on the
availability of the central priv structure. This will access already
freed memory.
There are multiple mitigations to choose from
- Clone all controller->priv data into the bus->priv structure.
- disable sysfs bind/unbind attributes
- Check for "bus->state != MDIOBUS_REGISTERED" in all callbacks
This SoC-integrated MDIO controller cannot be physically hot-plugged
and manual unbinding gives no benefit. The driver is usually
integrated into the kernel and not loaded as a module. Avoid a
complex driver rewrite (data duplication) for now and set
suppress_bind_attrs to true to prevent unbinding via sysfs. This
mitigates issues for the known use cases.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-7-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some MDIO buses require programming PHY polling registers depending
on the PHY type. RealTek switch SoCs are the most prominent example
of a DSA switch which doesn't allow to program MAC speed, duplex and
flow-control settings without using PHY polling to do so [1].
Avoid a half-baked solution in the MDIO bus driver because
- it must reinvent the bus scanning to determine the PHYs and
- it must anticipate the right point in time (e.g. deferred PHYs).
Hence there is a need to inform the MDIO bus driver that a PHY is
being attached or detached. Provide two hooks in struct mii_bus
- notify_phy_attach(): called in phy_attach_direct() after PHY
hardware has been initialized and just before PHY is resumed.
- notify_phy_detach(): called in phy_detach() right after PHY
has been suspended.
Worth to notice: As of now phy_detach() is not 100% LIFO symmetric
to phy_attach_direct(). E.g. sysfs links are torn down before
suspend while being created before resume. Without reordering of the
detach function the above mentioned notifier placement is the best
possible symmetric implementation. An unconditional call of
notify_phy_detach() was favoured [3].
Remark! A slightly different version of this patch was part of a
former series [2]. The discussion already showed that an initialization
hook should be placed somewhere late during the whole setup. This
commit implants it right after phy_init_hw() as suggested. On top of
this it adds the detach hook.
[1] https://github.com/openwrt/openwrt/pull/21515#discussion_r2714069716
[2] https://lore.kernel.org/netdev/cover.1769053496.git.daniel@makrotopia.org/
[3] https://lore.kernel.org/netdev/9e40f50b-357a-4a93-9f59-94847850835d@lunn.ch/#t
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-6-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the upcoming MDIO bus notification enhancements the PHY detach path
needs to inform the bus about these actions. Until now phy_detach() is
used for the regular detach path as well as from the phy_attach_direct()
error paths So in the future there must be a clear indication if a
notification is needed (normal path) or not (cleanup path).
Carve out the phy_detach() code into a new helper phy_detach_internal()
and make phy_detach() a short stub that calls the new helper.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-5-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hardware polling breaks C45 over C22 PHY access. Currently this
is accepted by the driver but it silently fails with undefined
results. Make the situation clear to the caller by adding checks,
returning an error and giving a one-time warning message.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-4-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a detailed explanation how the hardware polling unit in the
Realtek Otto switches works. This simplifies developing future
patches and reviewing them.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20260831143439.2404484-3-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The lower end Realtek Otto switches provide 1G only and are divided into
two series:
- Maple : RTL838x up to 28 ports
- Cypress: RTL839x up to 52 ports
The Maple based devices have 3 different SoCs: RTL8380, RTL8381 and
RTL8382. The Cypress series consists of the RTL8391, RTL8392 and
RTL8393 SoCs. The MDIO controller of these switches works like the
existing RTL93xx logic but has different characteristics and different
registers. Add new compatibles in the device tree.
With the extended compatibility list change the title to better reflect
its scope. Especially add the "Ethernet" tag as these devices have
multiple MDIO controllers.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260831143439.2404484-2-markus.stockhausen@gmx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mike Rapoport says:
====================
USB: replace page allocator calls with kmalloc()
This is a (small) part of larger work of replacing page allocator calls
with kmalloc.
My initial intention a few month ago was to remove ugly casts [1], but then
willy pointed out that Linus objected to something like this [2] and it
looks like more than a decade old technical debt.
Largely, anything that doesn't need struct page (or a memdesc in the
future) should just use kmalloc() or kvmalloc() to allocate memory.
kmalloc() guarantees alignment, physical contiguity and working
virt_to_phys() and beside nicer API that returns void * on alloc and
doesn't require to know the allocation size on free, kmalloc() provides
better debugging capabilities than page allocator.
Another thing is that touching these allocation sites gives the reviewers
opportunity to see if a PAGE_SIZE buffer is actually needed or maybe
another size is appropriate.
For larger allocations that don't need physically contiguous memory
kvmalloc() can be a better option that __get_free_pages() because under
memory pressure it's is easier to allocate several order-0 pages than a
physically contiguous chunk with the same number of pages.
And last, but not least, removing needless calls to page allocator should
help with memdesc (aka project folio) conversion. There will be way less
places to audit to see if the user was actually using struct page.
The patches are deliberately kept small: each one deals with a single
driver or subsystem and with a single type of allocation, so that every
conversion can be reviewed, and if needed reverted, on its own.
====================
Link: https://patch.msgid.link/20260830-usb-v1-0-aa349c302246@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
speedtch_upload_firmware() allocates a temporary buffer used to feed the
firmware to the device.
This buffer can be allocated with kmalloc() as there's nothing special
about it to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260830-usb-v1-3-aa349c302246@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
cxacru_fw() allocates a temporary buffer used to feed the firmware to the
device and cxacru_bind() allocates the transfer buffers for the command
URBs.
These buffers can be allocated with kmalloc() as there's nothing special
about them to go directly to the page allocator.
kmalloc() provides a better API that does not require ugly casts and
kfree() does not need to know the size of the freed object.
Performance difference between kmalloc() and __get_free_pages() is not
measurable as both allocators take an object/page from a per-CPU list for
fast path allocations.
For the slow path the performance is anyway determined by the amount of
reclaim involved rather than by what allocator is used.
Replace use of __get_free_page() with kmalloc() and free_page() with
kfree().
Link: https://lore.kernel.org/all/635405e4-9423-4a25-a6e7-e03c8ea0bcbe@redhat.com
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
Link: https://patch.msgid.link/20260830-usb-v1-2-aa349c302246@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 71338aa7d0 ("net: convert %p usage to %pK") which is from
2011 and changed the %p annotation for pointer to %pK. Back then the
default behaviour for %p was to print the pointer. The %pK modifier was
introduced to able to control the behaviour of specific pointer values
without changing the behaviour of %p for everyone. It was dedicated to
avoid leaking pointers via /proc.
There was also the idea to remove the check from formatting the string
and move to the open callback with some helpers but this did not happen.
Things changed over time. The default behaviour for %p is now to print a
hash pointer which does not leak the address but allows to correlate if
two pointers are equal.
The policy on %p is to not introduce new ones. This is somehow in
between since it already exists. The pointer are usually socket pointers
and I don't see any value in exposing them. Therefore I am following the
recommendation of removing them. Since their usage in /proc/ can be
considered ABI I replace the pointer with a 0.
Replace the %pK annotation with 0 value. Correct the spacing for the
cases where pointer is at the beginning.
Reviewed-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20260901160345.eeknHmY2@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A netdevsim VF port cannot process incoming data. It never runs
nsim_queue_init(), so ns->rq is NULL, and nsim_vf_netdev_ops has no
->ndo_open, so its NAPI is never set up either.
nsim_setup() offers NETIF_F_LOOPBACK to both PF and VF ports. Turning
it on for a VF makes nsim_start_xmit() take ns itself as peer_ns and
dereference peer_ns->rq[], which panics.
A VF cannot deliver packets at all: it can't be linked as a peer either,
since netdev_is_nsim() only matches the PF netdev_ops, so ns->peer is
always NULL and every skb ends up dropped. Give VF ports a dedicated
xmit that just drops the traffic, so VFs no longer depend on PF-only
state in nsim_start_xmit().
Reproduce in qemu:
modprobe netdevsim
echo "90 1" > /sys/bus/netdevsim/new_device
echo 2 > /sys/bus/netdevsim/devices/netdevsim90/sriov_numvfs
devlink dev eswitch set netdevsim/netdevsim90 mode switchdev
ethtool -K eth2 loopback on # eth2 is the vfnum 0 port
ip link set eth2 up
Panic:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 UID: 0 PID: 141 Comm: kworker/0:3 Not tainted 7.2.0+ #338 PREEMPT
Workqueue: mld mld_ifc_work
RIP: 0010:nsim_start_xmit (drivers/net/netdevsim/netdev.c:159)
dev_hard_start_xmit ( net/core/dev.c:3953)
sch_direct_xmit (net/sched/sch_generic.c:372)
__dev_queue_xmit (net/core/dev.c:4262 net/core/dev.c:4884)
neigh_resolve_output (net/core/neighbour.c:1616)
ip6_finish_output2 (net/ipv6/ip6_output.c:138)
ip6_finish_output (net/ipv6/ip6_output.c:221)
ip6_output (net/ipv6/ip6_output.c:248)
......
Cc: stable+noautosel@kernel.org # netdevsim is a test harness, it's never loaded on production systems
Signed-off-by: Jiayuan Chen <jiayuan.chen@linux.dev>
Link: https://patch.msgid.link/20260901061851.61734-1-jiayuan.chen@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
selftests: drv-net: split up gro.py
gro.py runs its full set of cases three times over - against SW GRO,
HW GRO and LRO. It's our test with the longest runtime. The 318 cases
take 12m30s on mlx5 with a debug kernel.
We will likely add more subcases here as the time goes on, so it's
time to start splitting it up. Long runtime wastes time on retries
(if any of the 300+ cases fails we try to check if it's a real failure
or flake an re-run the whole thing). It also forces us to increase
timeout for the whole test suite.
v1: https://lore.kernel.org/20260831163734.1121891-1-kuba@kernel.org
====================
Link: https://patch.msgid.link/20260901200728.2063720-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The XDP test takes 9m30s on the slowest NIC with debug kernel.
Let's give ourselves a 50% margin and set the timeout to 15min.
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260901200728.2063720-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gro.py runs its full set of cases three times over - against SW GRO,
HW GRO and LRO. It's our test with the longest runtime. The 318 cases
take 12m30s on mlx5 with a debug kernel.
Bumping the timeout for all tests feels wrong when we can so easily
split the GRO test by execution mode. Shorter runtime also helps retry
just the failing portion / mode (we retry failing tests to try to
detect flakes vs real failures).
Move the main logic to gro_lib.py and add one program per mode -
gro_sw.py, gro_hw.py and gro_lro.py, 102 cases each. Move PPPoE to
a dedicated test. It has been tacked onto the tests in an ugly way,
and it only runs against SW GRO anyway.
Note that unfortunately this will case a rename of all test cases.
The mode moves from the case name to the test name
gro.py test.sw_ipv4_data_same
becomes
gro_sw.py test.ipv4_data_same
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260901200728.2063720-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to free up the gro_hw.py name for the HW-GRO half of gro.py,
which we need to split by mode (sw / hw / lro). The file checks mostly
qstat counters, so name it after stats.
Reviewed-by: Joe Damato <joe@dama.to>
Reviewed-by: Nimrod Oren <noren@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260901200728.2063720-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The binding references ethernet-controller.yaml schema, which already
defines a dependency of pcs-handle-names on pcs-handle, thus duplicating
it here is redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Link: https://patch.msgid.link/20260901061255.25734-2-krzysztof.kozlowski@oss.qualcomm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel says:
====================
net: dsa: realtek: enable RTL8365MB power supplies
The RTL8365MB family has several external power rails (analog, digital I/O
and PLL supplies) that on some boards are gated by regulators. Until now the
driver assumed they were always on, so it could not be used on designs that
keep these rails software-controlled.
This series adds a device-tree description for those supplies and enables
them in the driver before the chip is accessed:
The supplies are optional: boards that hard-wire the rails work unchanged
====================
Link: https://patch.msgid.link/20260831123637.666457-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace the open-coded dev_err() + ERR_CAST() on the reset GPIO error
path with dev_err_cast_probe(), matching the reset controller above and
staying quiet on -EPROBE_DEFER.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://patch.msgid.link/20260831123637.666457-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The power supplies powering the IC may not necessarily be enabled by the
time the driver probes. The binding describes the power rails, so enable
them at probe with devm_regulator_bulk_get_enable(), before the reset line
is requested and driven, so the chip is powered before its pins are driven.
Boards that do not describe these supplies fall back to dummy regulators
(with a "supply not found" warning) and keep working as before.
A board that describes supplies but no reset line still needs to wait for
the chip to boot before the first register access, so apply the existing
start delay in that case too.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://patch.msgid.link/20260831123637.666457-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Document the RTL8365MB power rails as optional supplies. They are optional
because the rails are often always-on; some designs break them out for
granular hwmon monitoring and regulator control.
They are scoped to realtek,rtl8365mb: different Realtek switch families use
different power-rail naming schemes, so these rails do not apply to other
families such as realtek,rtl8366rb (VDDA/VDD_CORE/VDDIO/...).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Reviewed-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20260831123637.666457-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
