HDMI audio is available on the Rock 5B HDMI TX ports.
Enable it for both ports.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-4-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
For hdmi0_sound, use the simple-audio-card driver with the hdmi0 QP node
as CODEC and the i2s5 device as CPU.
Similarly for hdmi1_sound, the CODEC is the hdmi1 node and the CPU is
i2s6, but only added in the rk3588-extra.dtsi device tree as the second
TX HDMI port is not available on base versions of the SoC.
The simple-audio-card,mclk-fs value is set to 128 as it is done in
the downstream driver.
The #sound-dai-cells value is set to 0 in the hdmi0 and hdmi1 nodes so
that they can be used as audio codec nodes.
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3588 Tiger Haikou
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Fixes: 419d191810 ("ASoC: simple-card-utils: use __free(device_node) for device node")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20250217215641.372723-3-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT changes to enable the second HDMI output port on
Rockchip RK3588 EVB1.
While at it, switch the position of &vop_mmu and @vop to maintain the
alphabetical order.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-5-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
The HDMI1 PHY PLL clock source cannot be added directly to vop node in
rk3588-base.dtsi, along with the HDMI0 related one, because HDMI1 is an
optional feature and its PHY node belongs to a separate (extra) DT file.
Therefore, add the HDMI1 PHY PLL clock source to VOP2 by overwriting its
clocks & clock-names properties in the extra DT file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-4-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI1 PHY.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250223-vop2-hdmi1-disp-modes-v2-3-f4cec5e06fbe@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable USB3 OTG and it's related PHY node. And the PHY will
also be shared with the upcoming DisplayPort controller.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20250223100757.73531-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add dt node for RK3528 clock and reset unit. Clock "gmac0_clk" is
generated by internal Ethernet phy, a fixed clock node is added as a
placeholder to avoid orphans.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250217061142.38480-9-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are two types of clocks in RK3528 SoC, CRU-managed and
SCMI-managed. Independent IDs are assigned to them.
For the reset part, differing from previous Rockchip SoCs and
downstream bindings which embeds register offsets into the IDs, gapless
numbers starting from zero are used.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250217061142.38480-6-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3588 Tiger routes I2C2 signals to the Q7 Camera FFC connector (P2) but
nothing on the SoM itself is on that bus, therefore it'll be up to the
adapter connected to the Q7 Camera FFC connector (P2) to enable the I2C2
controller, if need be.
Thus, disable it by default.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-9-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX30 Ringneck only exposes I2C3 as LVDS_BLC_CLK/DAT on Q7 golden fingers
but nothing is on that bus on the SoM itself. Therefore, let's enable
the I2C3 bus where it makes sense, in the Haikou carrierboard DTS.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-8-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The signals are exposed on Q7 golden fingers but it's not a given that
the carrierboard will have an Ethernet jack. So let's move the enabling
of the Ethernet controller to the carrierboard DTS instead.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-7-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Haikou carrierboard has an EEPROM on LVDS_BLC_CLK/DAT which are
signals that can carry either I2C or be used as HPD for eDP0/1.
Only eDP0 is routed from RK3399 Puma SoM but only exposed on Haikou
through the Video Connector, a fake PCIe connector. So to be able to use
eDP one would need to use a Device Tree overlay. Therefore, let's
default to having an EEPROM in Haikou carrierboard DTS.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-6-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2S0 is routed to the Q7 golden fingers and, on Haikou carrierboard, to
an I2S codec. Nothing aside from signal routing is done on the SoM,
therefore it's the duty of the carrierboard to enable I2S0 whenever an
I2S codec is present.
Such is the case of the Haikou carrierboard, therefore let's migrate the
enabling of this controller to the carrierboard DTS instead of the SoM
DTSI.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-5-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The bus is only exposed on Q7 Camera FFC connector which accepts
external adapters such as Q7 Camera Demo.
The enabling of I2C6 should therefore be done in the adapter Device Tree
Overlay and not in the SoM DTSI, so let's disable it by default.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-4-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
I2C6 is not exposed on Q7 golden fingers which is for routing signals to
the carrierboard but on Q7 Camera connector, for routing signals to an
additional adapter (e.g. Q7 Camera Demo adapter).
Therefore, let's move the modification of I2C6 bus to Puma DTSI.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-3-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The DDC bus is necessarily on I2C3, that's how it's exposed by RK3399
Puma on the Q7 golden fingers, so let's move it to the SoM DTSI instead.
If the carrierboard doesn't route it for some reason, /delete-property/
can be used to remove it.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-2-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In its default configuration (SW2 on "UART1"), UART5 is exposed on the
DB9 RS232/RS485 connector. While the same signals are also exposed on
Q7_GPIO5 and Q7_GPIO6, a GPIO header, and thus could be used for other
purposes, RK3399 Puma Haikou and PX30 Ringneck Haikou do enable the UART
controller exposed on the DB9 connector, so let's keep consistency
across our modules and enable it on RK3588 Tiger Haikou by default too.
Add a comment while at it to explicit where this controller is routed
to.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250218-tsd-align-haikou-v1-1-5c44d1dd8658@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa ROCK 4D board is based on the Rockchip rk3576 SoC.
The device tree adds support for basic devices:
- UART
- SD Card
- Ethernet
- USB
- RTC
It has 4 USB ports but only 3 are usable as the top left one is used
for maskrom.
It has a USB-C port that is only used for powering the board.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Link: https://lore.kernel.org/r/20250218160714.140709-3-detlev.casanova@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the otp node to the rk3576 soc devicetree including the
individual fields we know about.
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250210224510.1194963-7-heiko@sntech.de
This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with RK3399 Puma SoM.
The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.
Its main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250221-ringneck-dtbos-v2-5-310c0b9a3909@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with PX30 Ringneck SoM.
The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.
Itss main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250221-ringneck-dtbos-v2-4-310c0b9a3909@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The HAIKOU-LVDS-9904379 adapter is an adapter for PX30 Ringneck with the
Haikou carrierboard. It is to be inserted in the fake PCIe slot labelled
Video Connector.
This adapter expects an Admatec 9904379 1024x600 LVDS display with
backlight and touchscreen. An EEPROM is also found on the adapter.
This adds support for this adapter on PX30 Ringneck when inserted in
Haikou carrierboard.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250221-ringneck-dtbos-v2-3-310c0b9a3909@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the RK3588's standalone hardware random number generator node to its
device tree, and enable it.
Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Link: https://lore.kernel.org/r/20250204-rk3588-trng-submission-v2-6-608172b6fd91@collabora.com
[changed reset-id to its numeric value while the constant makes its
way through the crypto tree]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As the name implies, it is built around the RK3576 SoC with 4x Cortex-A72
cores, four Cortex-A53 cores and Mali-G52 MC3 GPU.
Storage options are EMMC, SD-Card, a 2242 M.2 slot and the possibility to
use UFS 2.0 storage.
Video Output options are a HDMI port, a DSI connector as well as Display-
Port via the TypeC connector (all of them not yet supported).
Networking options are a Low-profile Gigabit Ethernet RJ45 port with
Motorcomm YT8531 PHY as well as WiFi via an AMPAK AP6256 module.
USB ports on the board are 1x USB 3.0 port, 1x USB 2.0 port, 1x USB Type-C
and it comes with 40-pin GPIO header
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250210205126.1173631-3-heiko@sntech.de
Add devicetree binding for the ROC-RK3576-PC SBC.
The board is based on the RK3576 SoC (4*Cortex-A72 + 4*Cortex-A53).
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250210205126.1173631-2-heiko@sntech.de
The Pre-ICT tester adapter connects to RK3588 Jaguar SBC through its
proprietary Mezzanine connector.
It exposes a PCIe Gen2 1x M.2 connector and two proprietary camera
connectors. Support for the latter will come once the rest of the camera
stack is supported.
Additionally, the adapter loops some GPIOs together as well as route
some GPIOs to power rails.
This adapter is used for manufacturing RK3588 Jaguar to be able to test
the Mezzanine connector is properly soldered.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org> # Makefile
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250211-pre-ict-jaguar-v6-4-4484b0f88cfc@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to commit 4065853475 ("arm64: dts: rockchip: Add rock5b
overlays for PCIe endpoint mode"), Rock 5B can operate in PCIe endpoint
mode. For that to work, the rk3588-rock-5b-pcie-ep.dtbo overlay needs to
be applied on Rock 5B base Device Tree. If that Rock 5B is connected to
another Rock 5B, the latter needs to apply the
rk3588-rock-5b-pcie-srns.dtbo overlay.
In order to make sure the overlays are still valid in the future, let's
add a validation test by applying the overlays on top of the main base
at build time.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250211-pre-ict-jaguar-v6-3-4484b0f88cfc@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Edgeble NCM6A/NCM6B can have WiFi modules connected and this is
handled via an overlay (commit 951d6aaa37 ("arm64: dts: rockchip: Add
Edgeble NCM6A WiFi6 Overlay")).
Despite the name of the overlay, it applies to both NCM6A and NCM6B[1].
In order to make sure the overlay is still valid in the future, let's
add a validation test by applying the overlay on top of the main bases
at build time.
[1] https://lore.kernel.org/linux-rockchip/CA+VMnFyom=2BmJ_nt-At6hTQP0v+Auaw-DkCVbT9mjndMmLKtQ@mail.gmail.com/
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250211-pre-ict-jaguar-v6-2-4484b0f88cfc@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The WolfVision PF5 can have a PF5 Visualizer display and PF5 IO Expander
board connected to it. Therefore, let's generate an overlay test so the
application of the two overlays are validated against the base DTB.
Suggested-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Michael Riesch <michael.riesch@wolfvision.net>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Link: https://lore.kernel.org/r/20250211-pre-ict-jaguar-v6-1-4484b0f88cfc@cherry.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Going over the 80-column width limit, and using all 100 columns, is intended
for improving code readability. This wasn't the case in a few places in the
Quartz64 Model A/B board dts files, so let's reflow them a bit, to both obey
the 80-column limit and make them a bit more readable.
No intended functional changes are introduced by these changes.
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/7eea4ebdb19d5f43d24074a166e6c46bb5424d46.1739218324.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Remove Optee node from rk3588 devicetree. When Optee is present and
used the node will be added automatically by U-Boot when
CONFIG_OPTEE_LIB=y and CONFIG_SPL_ATF_NO_PLATFORM_PARAM is not set.
When Optee is not present or used, the node will trigger a probe
that generates a (harmless) message on the kernel log.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20250130181005.6319-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Edgeble-6TOPS modules configure HDMI1 for HDMI Out from RK3588.
Enable it on Edgeble-6TOPS IO Board dtsi.
Cc: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20241227132936.168100-1-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the necessary DT changes to enable the second HDMI output port on
Radxa ROCK 5B.
While at it, switch the position of &vop_mmu and @vop to maintain the
alphabetical order.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Alexandre ARNOUD <aarnoud@me.com>
Link: https://lore.kernel.org/r/20241211-rk3588-hdmi1-v2-4-02cdca22ff68@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the second HDMI TX port found on RK3588 SoC.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Jagan Teki <jagan@edgeble.ai> # edgeble-6tops-modules
Tested-by: Alexandre ARNOUD <aarnoud@me.com>
Link: https://lore.kernel.org/r/20241211-rk3588-hdmi1-v2-3-02cdca22ff68@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In preparation to enable the second HDMI output port found on RK3588
SoC, add the related PHY node. This requires a GRF, hence add the
dependent node as well.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: Jagan Teki <jagan@edgeble.ai> # edgeble-6tops-modules
Tested-by: Alexandre ARNOUD <aarnoud@me.com>
Link: https://lore.kernel.org/r/20241211-rk3588-hdmi1-v2-2-02cdca22ff68@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
H96 Max V58 has its spdif_tx0 controller wired to a dedicated optical
Toslink SPDIF socket, enable it in the device tree
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Link: https://lore.kernel.org/r/20250120-rk3588-spdif-v1-3-1415f5871dc7@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip company name has update to below name since 2021:
Rockchip Electronics Co., Ltd.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241205082258.857018-1-kever.yang@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add dts for Ariaboard Photonicat RK3568.
Partially based on downstream board dts. [1]
Working IO:
Debug UART
SDIO QCA9377 WiFi and Bluetooth
M.2 E-Key PCIe WiFi and Bluetooth
M.2 B-Key USB Modem WWAN
Ethernet WAN Port
MicroSD Card slot
eMMC
HDMI Output
Mali GPU
USB Type-A
Not working IO:
Ethernet LAN Port (Lack of SGMII support)
Power management MCU on UART4 (Driver pending)
Not working IO in MCU:
Battery voltage sensor
Board temperature sensor
Hardware Power-off
Hardware Watchdog
Network status LED
Real-time clock
USB Charger voltage sensor
About onboard power management MCU:
A heartbeat must be sent to the MCU within 60 seconds,
otherwise the MCU will restart the system.
When powering off, a shutdown command needs to be sent to the MCU.
When the power button is long pressed, the MCU will send a shutdown
command to the system. If system does not shutdown within 60 seconds,
the power will be turned off directly.
MCU only provides voltage for charger and battery.
Manufacturer removed RK8xx PMIC.
[1] https://github.com/photonicat/rockchip_rk3568_kernel/blob/novotech-5.10/arch/arm64/boot/dts/rockchip/rk3568-photonicat-base.dtsi
Signed-off-by: Junhao Xie <bigfoot@classfun.cn>
Link: https://lore.kernel.org/r/20250114001411.1848529-4-bigfoot@classfun.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa Rock 5C supports both CRU-based (default) and PMIC-based reset
upon thermal runaway conditions. The former resets the SoC by internally
poking the CRU from TSADC, while the latter power-cycles the whole board
by pulling the PMIC reset line low in case of uncontrolled overheating.
Switch to a PMIC-based reset, as the more 'thorough' of the two.
Tested by temporarily setting rockchip,hw-tshut-temp to 65C to simulate
overheating - this causes the board to reset when any of the on-chip
temperature sensors surpasses the tshut temperature.
Requires Alexander's patch [1] fixing TSADC pinctrl assignment
[1] https://lore.kernel.org/r/20250130053849.4902-1-eagle.alexander923@gmail.com
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250204-rock-5c-tshut-v1-1-33301e4eef64@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the recommended chassis-type root node property so userspace can
request the form factor and adjust their behavior accordingly.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250207111157.297276-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The hdptxphy is a combo transmit-PHY for HDMI2.1 TMDS Link, FRL Link, DP
and eDP Link. Therefore, it is better to name it hdptxphy0 other than
hdptxphy_hdmi0, which will be referenced by both hdmi0 and edp0 nodes.
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250206030330.680424-3-damon.ding@rock-chips.com
[added armsom-sige7, where hdmi-support was added recently and also
the hdptxphy0-as-dclk source I just added]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
For now only HDMI0 output is supported, hence add the related PLL clock.
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20250204-vop2-hdmi0-disp-modes-v3-5-d71c6a196e58@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since commit c4b09c5620 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI0 PHY.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20250204-vop2-hdmi0-disp-modes-v3-4-d71c6a196e58@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
